hello
i have samsung s8530 with damaged imei 000000000000 i try to repair it But i cant find any tool that can do it ?
i try to read full dump with Jtag and after that i open it with hexeditore and start to search for Imei i fond alot off imei, i change them and save me dump file and write it again to phone but phone hang at start and stop i flashed it with normal firmware with multloader phone wok ok but with damaged imei same before condition ???
any idea to repair it ??????
and what if i get anew phone and read full dump with jtage and writ to my phone u think that will help or not ??
thanks
JTAG + S8530 sounds interesting.
I'll write you PM...
Best Regards
yes i see your massge but i need more information check your pm plz.
thank's
Related
i tried to solve my problem for 1 day before i make this thread.i have an unbraded ls ks20 with english rom v10c.i tried to pass a greek rom (v10g vodafone).after flash it and the phone start setup shows me a message "illegal use" so i went back to english rom.since then my phone doesn't conect to the network "no service".everything else works fine .what should i do?did i kill my brand new lg ks20?
i really need help!
Never flashed before - but you need a special file (nv?) that is unique to your phone. If you didn't back that up, yes you killed it ! If you did search XDA for instructions on how to restore it.
You can do this step to find your signal.
1.backup your ks-20 NV file,the file you can backup from firmware.
2.firm ENG rom and chose ERASE ESF.
3.complete the flash,you can go in the system,and find Windag_open.cab install on the device,and open engineer mode.
4.open firmware,only flash nv file,since reset ,you will find the signal.
I do this to find my signal
lol, He loss calibration data from handset!!!! If there is no service after flashing without NV backup, only way to resolve that problem to flash the NVRAM with backup of another handset and correct IMEI and BT address.
To everyone,
If u need .nv2 file, pm me with ur imei no. and email address, i can generate one for you, but the last digit, which is calculated by your phone, would likely to be different and also i can only generate branded .nv2 since i only got branded .nv2 file. It could be work in unbranded phone but just u need to flash a branded rom or hybrid rom to use with it.
thank you raykisi you are the best it works 100%.
LG KS20 Network Problems
Sorry,
My e-mail is [email protected]
I can't help you with only your email address
Read the posts in my signiture pls
LG KS20 Network Problem
I have read it. Again, many thanks, specially to you; everithing from there was very helpfull.
I will give you the IMEI number: 357323-01-137914-1
I have managed to write the IMEI to the phone with QPSt; do i need to do something else?
If i conect back with QPST shows the IMEI (without the last digit)
Unfortunatell i don't have a valid backup for the nv file
Any help will be great
Ths in advance
Hi raykisi,
I still have my .qcn file... but what I'm trying to do is a little bit different: put a KS20 rom on a MS25 mobile (similar mobile that we have here in Brazil).
I tried to recover my network config using my qcn backup but I couldn't...
My phone always shows "No Service".
Tooo bad...
;(
Hope you can help me...
Thanya
What does ERASE EST do? Why would you think this whole procedure will help find the signal? I asked because my KS20 doesn't find any signal in a lot of places but my wife's KS20 does. I am wondering if there is anything I can try to resolve my problem. Thanks.
sam_sun said:
You can do this step to find your signal.
1.backup your ks-20 NV file,the file you can backup from firmware.
2.firm ENG rom and chose ERASE ESF.
3.complete the flash,you can go in the system,and find Windag_open.cab install on the device,and open engineer mode.
4.open firmware,only flash nv file,since reset ,you will find the signal.
I do this to find my signal
Click to expand...
Click to collapse
can anybody know about it. .
i have a HP iPAQ 614c and after bios upgrade ( bios is not suporting my phone, but i read that after) they cant start. . . bootloader is dead (cant use any combination of keys to enter in bootloader) . .and i was reading that the only metod is a JTAG . .re-programing flash memory. . i would make a JTAG cable but i cant find testpoints on ipaq. . can somebody knows how to help me?
p.s. i was searching on the internet and i cant find any service manual. . .
anybody
is this possible. . that nobody know solution ???
I'm trying to find a solution
while connected to your phone and set up a jtag
prepared eboot.bin
need to learn from eboot.bin
address at which he wrote in RAM
and run
but so far I do not know the address
I hope someone can help me. I tried almost everything. My wave just won't boot normally. It all started when I tried to downgrade from Bada 2.0 (S8500XPKH3) to 1.2 (S8500XXJL2) and got a security port error while flashing (used Multiloader 5.65). My wave wouldn't boot up so I got someone to repair it with JTAG. Good thing it was revived. It can now go to download mode, however, i tried flashing almost all firmware versions (Bada 1.0, 1.2, 2.0) in different regions from samfirmware but to no avail.
I browsed through the forums hoping I can get an answer but I didn't see any similar case. I'm sure I'm doing the flashing right 'coz I get "All files complete." when flashing is done. Only that, every firmware that I try, it just stays in the logo screen when it starts up.
I'm looking forward for any response.
Best regards.
I guessed you have done all well. But still try this process:
1. Download a fresh, full and original firmware for your region from samMobile.com
(The firmware version does not matter, but it has to be full and for your region).
2. Make sure your battery is fully charged
3. Remove SIM and memory card from phone.
4. Ensure that all kies drivers are successfully installed.
5. Use multiLoader v5.65
6. Cross-check that your USB plug is not damaged (if possible use another one)
7. When flashing, make sure you tick the FULL DOWNLOAD option in multiLoader.
Try the above and report back. Best of luck.
yeah you should tick boot change and full download for a complete fresh installation
Good thing it was revived
Click to expand...
Click to collapse
Depend on how it was repaired via JTAG...
Maybe NV items are overwritten... this could be bad.
It is not the best idea to use Fullflash from others...
I have RIFF Box experiences...
Best Regards
P.S.:
Try to flash some Rsrc2_S8500(Mid).rc2
Maybe Bluescreen tell you what is missing...
adfree said:
Depend on how it was repaired via JTAG...
Maybe NV items are overwritten... this could be bad.
It is not the best idea to use Fullflash from others...
I have RIFF Box experiences...
Best Regards
P.S.:
Try to flash some Rsrc2_S8500(Mid).rc2
Maybe Bluescreen tell you what is missing...
Click to expand...
Click to collapse
Thanks for the tips guys. I tried the routine checking. I've also tried different a different pc. Same thing.
I'm more inclined to this adfree. NV items might be corrupted. I just know the basics of flashing.I tried several Rsrc2_s8500 (Mid) and yes I got a blue screen with details. I don't know how to interpret it myself but I remember there was IMEI not active. Will post the details later. Hope you or someone can share your thoughts.
Best regards.
I tried S8500XPKH3 again with Rsrc2_S8500(Mid).rc2 and I got this from Multiloader 5.65:
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Amss 12740.3KB OK[5.0s]
Apps 26214.4KB OK[12.3s]
Rsrc1 37748.7KB OK[14.4s]
Rsrc2 2884.3KB OK[1.3s]
FFS 49217.5KB OK[111.8s]
CSC 36085.8KB OK[106.0s]
SHPAPP 203259.9KB OK[368.3s]
All files complete[638.0s]
Phone reboots and comes up with blue screen:
S/W version: S8500+XP+KH3
Modem: Q6270B-KPRBL-1.5.45t
SHP: VPP R5 2.1.1
Build Host: S1-AGENT08
Build At: 2011/08/16 20:56:16
Aoo Debug Level: 0
ASSERTION_ASSERT: 0 failed. (file SysSecureBoot.c, line 4193) BoAn4193
<Call stack information>
PC = 4000C8D3 OemDumpRegister
LR = 4000C8D7 OemDumpRegister
<Mocha Task Call stack>
_SysAssertReport
__SysSecBootReadNetLockInfoFromFile
ALL HW Information:
HW VERSION: S8500_rev07
IMEI VERSION: Not Active
RF CAL DATE: Not Active
Bad Block Information:
nNumBMPs: 0
nAge: 0
Run Time Bad Block Occurred:
Init BMPs - 2, Current BMPs = 0
Nucleus Task Information:
Running Task name - Mocha Slices = 0000001E Wait = 00000000
Signal = 00000000 Priority = 0
I've been working on this for a week now but no matter what firmware I flash, i can't get my wave to boot normally
Try qualcomm tools to activate imei
ask Adfree or use google to find the qualcomm tools program and then make your imei active using your pc.
what region was your 8500 originally?
remember that different region firmware use different boot files.
Try to use the boot files that was on your wave originally.
For some reason, it's showing "IMEI not active" when I get the blue screen after flashing with Rsrc2_S8500(Mid).rc2.
I read adfree's qualcomm tools guide and it was more on editing the product code. And, i can't access the configuration mode/hidden menu since I can't boot the phone normally.
IMEI is NV item 550 and ...
But it is secured by...
I have never tried on S8500...
Lost IMEI is enough evidence, that NV items are corrupt/missing/damaged...
I'll try to analyze your Error message...
.. will report later.
Best Regards
Edit 1...
SysSecureBoot
SysSecBootReadNetLockInfoFromFile
Click to expand...
Click to collapse
Maybe also Netlock? So maybe without IMEI Security check failes...
I think the guy who tried to resurrect my phone was using JTAG Medusa. Is there any possibility something went wrong during the process? I was just happy that the phone can go on download mode but didn't expect that whichever firmware I try, phone is just stuck on logo.
With regard to the IMEI, should i recover it, will it have a good chance to fix the problem? Can i use qualcomm tools even if the phone can only run on download mode?
if use medusa make this erase full flash after that write full from support stop writ flash in 6% in flash procedure after this flash full flash all files with boot after this pach wit z3x pachv2.Repair imei and al by ok
tested with s8500 whoo come in donload mode with 3 butons vol - lock and power
in first when try flash bada 1.0 soft after ffs write in screen see missing fota 2.0 please instal instal bada 1.2 after this
@OP:
Your SysSec data, which is closely related to NvData, has been damaged, probably by JTAG ovewrite. These data are encrypted by device-unique key.
It is possible to repair it without JTAG, through modified FOTA. But I don't think I'm the one to try this. Last time I played with that data I damaged my BL3. :\
Thanks for those who provided their insights. I kind of gave up last week and had to bring my phone to the service center. Fortunately or not, the tech had to replace the motherboard which cost around 170 USD including the "repair fee". My phone's back with a new motherboard and ready for some risky flashing again. Hehe.
Anyway, thanks again guys. Good day to y'all!
full erase flash only 6% from full after thath full flash with orginal flasher now read wit rj45 cable with z3x nvm from phone in 550 string see if imei is 359321654 need write 8a31391256 and write in phone now imei ok or select in z3x i 5500 put orginal imei and sn repair all come good and working
after all ok read full again from phone search s8500 and see you detail if need edit as your orginal string
ЄЇ~GT-S8500............їµ±№....................................TMU.....2010-06-01....АМАз±Х..................S8500BOJE7_TMOJE7...564C......9750......86210000114318......KAC007021M(S8500)...-
During my plays with RIFF JTAG and few stupid experiments with full erase I'm now facing same problem...
Strange, but this happens with my own JTAG dump...
Will see how long I need to repair this...
Best Regards
It seems no good idea to be. To erase whole NAND via JTAG...
Anyway... long time and luck... I was able to bypass Boot Cycle and then to Restore NV items via QPST...
Maybe 1 part of solution is, to use Firmware BOJE7 with Bootloader XXJEE...
Then maybe your handset start...
Now you can access menu to change to Qualcomm Diag Port for restoring NV items...
Best Regards
Hi
as u see @ a subject a meid (imei) is lost >>>>
i was changing rom and its hang and restart without working soo i open a emergency mode and i lost i nv(m) and a meid (imei)!!!! and i did't find any shop can repair it..... please any suggestion plz
I am trying to unbrick my i8150. When it is connected to Win7x64. It is detected as Quallcom HS. I am going to use QPST to recover my i8150. But i need boot and phone images (hex images). Can anyone help me to get these files??
Also QCN file may be needed... Please help me....
Location Turkey.
hakanbilir said:
I am trying to unbrick my i8150. When it is connected to Win7x64. It is detected as Quallcom HS. I am going to use QPST to recover my i8150. But i need boot and phone images (hex images). Can anyone help me to get these files??
Also QCN file may be needed... Please help me....
Location Turkey.
Click to expand...
Click to collapse
odin can detect ur phone or not?
dec0der said:
odin can detect ur phone or not?
Click to expand...
Click to collapse
Odin can detect But odin is not the solution. Because bootloader corrupted. Can you do some backup with QPST and ODIN. I wil try them.
Odin can NOT detect. Only QPST...
Please I need some help.
I am playing with I9001, I8150 Bootloader on S8600 device...
I have RIFF JTAG, but limited skills...
1.
I9001 OSBL is loaded into RAM at which address?
Code:
0x8000 0000 ?
Is this wrong?
2.
Somebody have access to these JTAG, BOOTLOADER related sources?
http://forum.xda-developers.com/showpost.php?p=52583740&postcount=32
Thanx in advance.
If someone need QPST support for I8150...
Maybe I can help:
http://forum.xda-developers.com/attachment.php?attachmentid=2754655&d=1400627472
See this Video... it is S8600, but procedure could be the same.
Only DBL + OSBL + MBR from I8150 must be inside...
I can help...
See this Thread about Background infos...
http://forum.xda-developers.com/showthread.php?t=2116846&page=29
Best Regards