Related
I was rooted and running a 2.2 rom and wanted to install the damagecontrol 3.2 rom, which, as I understand it, requires NAND to be unlocked. I downloaded Simple Root and tried to unlock NAND.
When I turn on the phone I get stuck in a boot loop.
I try the recovery console. It takes a few minutes to load PC36diag.zip, the update for NAND which I already installed.
When I say no to the update and no to restarting I get into the menu, but if I try RECOVERY it loads the phone with the exclamation point, but I am unable to connect using the adb batch file I have always used before.
Also, when I try HBOOT USB the drivers aren't able to be installed. The device is read as "Android 1.0".
Can someone please help me?
devin.slick said:
I was rooted and running a 2.2 rom and wanted to install the damagecontrol 3.2 rom, which, as I understand it, requires NAND to be unlocked. I downloaded Simple Root and tried to unlock NAND.
When I turn on the phone I get stuck in a boot loop.
I try the recovery console. It takes a few minutes to load PC36diag.zip, the update for NAND which I already installed.
When I say no to the update and no to restarting I get into the menu, but if I try RECOVERY it loads the phone with the exclamation point, but I am unable to connect using the adb batch file I have always used before.
Also, when I try HBOOT USB the drivers aren't able to be installed. The device is read as "Android 1.0".
Can someone please help me?
Click to expand...
Click to collapse
Bootloop means you need to do a full wipe.
First thing's first, delete the PC36IMG.zip file from your SD. Then when you get the image of a phone with an exclamation mark, hold down the power and volume up key to get into recovery.
As for the last bit, I'm sorta' confused what you're problem is.
Part of my problem is that I can't delete the file from the SD card. Can't get into the OS and can't turn on USB.
Something similar happened to me. For me, instead of booting Damage Control, I switched it to Fresh and booted Fresh v3.0 and it worked and booted. Then I unlocked the Nand and made a nandroid. Then whipped everything 2 times and booted DC and it worked fine after that.
devin.slick said:
Part of my problem is that I can't delete the file from the SD card. Can't get into the OS and can't turn on USB.
Click to expand...
Click to collapse
You can get in to usb and put fresh on there by going to recovery mode and selecting one of the options that says USB, i can't remember the exact wording.
Added: I just checked it's called "USB-MS toggle"
devin.slick said:
Part of my problem is that I can't delete the file from the SD card. Can't get into the OS and can't turn on USB.
Click to expand...
Click to collapse
When you get the exclamation mark screen, hold down the Power and Volume Down key. Once in recovery mode, select the USB-MS Toggle feature, this mounts your SD card yto your PC. You should then be able to access the root of your SD card via the Removable Disk icon on your computer.
It wouldn't let me load USB from the console/whatever either... Another weird driver issue.
But after several more hard battery pulls I let it try again to boot and it showed me the "HTC, quietly brilliant" boot screen, which was different that what it had before.. I let it load and now I'm in android, but it says my SD card is removed.
Is this a part of the process necessary to unlock NAND?... Do I have NAND?
devin.slick said:
It wouldn't let me load USB from the console/whatever either... Another weird driver issue.
But after several more hard battery pulls I let it try again to boot and it showed me the "HTC, quietly brilliant" boot screen, which was different that what it had before.. I let it load and now I'm in android, but it says my SD card is removed.
Is this a part of the process necessary to unlock NAND?... Do I have NAND?
Click to expand...
Click to collapse
Check and see if your USB connection is in Charge Only or Disk Drive mode.
devin.slick said:
Is this a part of the process necessary to unlock NAND?... Do I have NAND?
Click to expand...
Click to collapse
no. You make your nand back up when you are in recovery mode and you select nand back up and it backs up everything. You'll need to follow through with the rest of the Nand unlocking instructions.
Did you download and follow the steps of the flash_image and mtg-eng.img etc etc...? Then the rest of the steps?
That's the first thing I tried to do when android loaded. It's not even an option. It says I removed my SD card.
I restarted, denied the update to get through to recovery, and I still can't connect with adb -it shows "Unknown Device" in the device manager.
devin.slick said:
That's the first thing I tried to do when android loaded. It's not even an option. It says I removed my SD card.
I restarted, denied the update to get through to recovery, and I still can't connect with adb.
Click to expand...
Click to collapse
are you connected with charge only? try hot sync (you need to install the program, which include drivers. this is on the htc website)
Mine worked for hot sync but not charge only
Looks like you may need to run through this. http://forum.xda-developers.com/showthread.php?t=695243
I've been reading that post.
When I select fastboot, it gives me other options.
bootloader
reboot
reboot bootloader
powerdown
If I select bootloader it takes me back to the main menu, if I select reboot, I get back to android and still do not have access to my SD card, so I can't get out of the debugging rom, or whatever it is.
I put another SD card in, so I don't have to wait on the update.zip to be read every single reboot, but that's all it did.
Am I doing something wrong?
Don't know then... sorry. You can try starting over from the beginning?
Best of luck.
FML.
Someone? I'm totally stuck.
And my phone says the the charger isn't delivering sufficient voltage... and I'm down to 8%.
HEEELLLPPP
its always an good idea to have a micro sd to sd adapter
After 3 locations, I found a Sprint store that actually existed... had them copy an update.zip that I brought on a flash drive onto my micro sd card. I tried booting into recovery and it didn't do the update. They suggested another store that does repairs, so I went to my 5th store, where I just dropped off my phone, hoping they'll reflash it fore me. I'm expecting a call back.
What a wonderful birthday this is turning out to be... lol. FML
UPDATE: I called them and they said the phone needs to be exchanged... but I don't know how they're going to react to it having the recovery/debug version of android on it.
Does anyone have ANY advice?
Just tell them to put in a fully charged battery for you. Then when you get it home try the Simple Root Guide you tried at first. This time post your issue (if you have any others) in that thread and myself or Jiqqa will help. Make sure before starting that guide that you have .NET framework and HTC sync installed on your computer. But you should be able to root phone and then be able to flash custom ROM after that.
Hey guys,,
i have a problem. i wanna root my phone via unrevoked and tried to install the HBOOT drivers. but when i plug in my phone the device manager doesn't name it as "Android 1.0" like it's shown in the tutorial, it is named "ADB". furthermore i can't install the hboot driver. any solutions?
The hboot drivers are installed when in hboot on the phone
so power down, power up holding the volume down and power.
Then device should show up as android device
ADB is when the phone is in debugging mode.
If you install "PdaNetA245_intl" this will install the ADB driver and you can cancel installation before installing the full application.
Unrevoked should then work
kingsizeriz said:
The hboot drivers are installed when in hboot on the phone
so power down, power up holding the volume down and power.
Then device should show up as android device
ADB is when the phone is in debugging mode.
If you install "PdaNetA245_intl" this will install the ADB driver and you can cancel installation before installing the full application.
Unrevoked should then work
Click to expand...
Click to collapse
Thing is, i can't select "HBOOT" in this fastbootmenu
Turn the phone on holding the volume down button. This will boot you into HBOOT
EddyOS said:
Turn the phone holding the volume down button. This will boot you into HBOOT
Click to expand...
Click to collapse
ok I'll try.. just a moment
So now I am in this HBOOT-mode, where I have the options "Fastboot, recovery, clear storage, simlock".
but now my PC can't identify anymore. it seems... when I plug in my device , where HBOOT stands normally, turns into "HBOOT USB PLUG" but that returns to HBOOT very fast...
it worked after plugging it in for about the 10th time!!!
sooo.... now I rebooted the phone activated debugging and plugged it back in.. now it recognizes it again as ADB and wants to install a new driver and unrevoked can't find it... how to go on?!
Urool said:
sooo.... now I rebooted the phone activated debugging and plugged it back in.. now it recognizes it again as ADB and wants to install a new driver and unrevoked can't find it... how to go on?!
Click to expand...
Click to collapse
Read my first reply. i have answered your previous question and this question, however it seems that you have just disregarded it.
ok rooting seemed to work now... but i tried to get a new rom on it.. so i followed the tutorial but couldn't find the ROM on my zip and when I want to reboot the phone it seemes to freeze @ the HTC bootscreen... i also tried with a wipe and booting again but it seems to totally freeze since i let it load for ~5 minutes now.
Urool said:
ok rooting seemed to work now... but i tried to get a new rom on it.. so i followed the tutorial but couldn't find the ROM on my zip and when I want to reboot the phone it seemes to freeze @ the HTC bootscreen... i also tried with a wipe and booting again but it seems to totally freeze since i let it load for ~5 minutes now.
Click to expand...
Click to collapse
Did you perform a wipe? Wipes are vital to maintaining a functional ROM. Time could also depend on the size of the ROM you flash, so it could take a while. If you have been waiting for +20 min, try to go old fashioned and push a stock onto your sd. Or you could go even more old fashioned and take out the sdcard and put the ROM onto it. Make sure the ROM is not corrupt
Sorry to bring an old thread back up guys.
I'm having the exact same problem helping a friend root, could you provide a link for the program you did in your first post please as googling it returns those crappy host file sites that never work..
I presume that step is necessary?
here you go
http://unrevoked.com/rootwiki/doku.php/public/unrevoked3
Not sure what happened, but my Desire won't get past the logo boot screen any longer, and RECOVERY mode in HBOOT just reboots the phone (regardless whether the SD card is installed or not). I can get into FASTBOOT however. I tried communicating with the Desire via adb console on my Windows XP system (after ensuring that I have the latest version of HTC Sync installed). "adb" commands do not recognize the phone (error: device not found). "Fastboot" commands do recognize the phone. (The command "fastboot devices", gives me this in return: SH09ER801629). So I'm not sure if my USB drivers are okay with adb, but the fastboot success seems to suggest so. (Also, "MyHTC" shows up under "Android Devices" in Device Manager).
The phone was rooted with ClockWork Mod using UnRevoked, and had Teppic stock Froy v.2.10.405.2 initd as the OS. Originally, it had TELUS-branded Eclair. I've downloaded the TELUS Froyo RUU.exe, but don't know how to install it on the phone, if I can't access RECOVERY mode or adb console. I don't think I ever set up a Gold Card, to my recollection. Also, I've been out of the smartphone scene for 6 months, and did no mods, no flashes, no program installs to my phone in that time. So it's a mystery as to why this is happening. But the phone had been acting up lately, rebooting by itself during a call every so often.
HBOOT screen:
Bravo PVT-3 SHIP S-ON
HBOOT 0.83 0001
RADIO 5.10.05.30
Cyanoid said:
Not sure what happened, but my Desire won't get past the logo boot screen any longer, and RECOVERY mode in HBOOT just reboots the phone (regardless whether the SD card is installed or not). I can get into FASTBOOT however. I tried communicating with the Desire via adb console on my Windows XP system (after ensuring that I have the latest version of HTC Sync installed). "adb" commands do not recognize the phone (error: device not found). "Fastboot" commands do recognize the phone. (The command "fastboot devices", gives me this in return: SH09ER801629). So I'm not sure if my USB drivers are okay with adb, but the fastboot success seems to suggest so. (Also, "MyHTC" shows up under "Android Devices" in Device Manager).
The phone was rooted with ClockWork Mod using UnRevoked, and had Teppic stock Froy v.2.10.405.2 initd as the OS. Originally, it had TELUS-branded Eclair. I've downloaded the TELUS Froyo RUU.exe, but don't know how to install it on the phone, if I can't access RECOVERY mode or adb console. I don't think I ever set up a Gold Card, to my recollection. Also, I've been out of the smartphone scene for 6 months, and did no mods, no flashes, no program installs to my phone in that time. So it's a mystery as to why this is happening. But the phone had been acting up lately, rebooting by itself during a call every so often.
HBOOT screen:
Bravo PVT-3 SHIP S-ON
HBOOT 0.83 0001
RADIO 5.10.05.30
Click to expand...
Click to collapse
if i'm not mistaken you can run the ruu and it should see the device if connected to pc with fastboot loaded.
as for trying to get back without losing data i'm new to all this so no idea
if you had run ruu on the phone and it was wrong type (i.e gsm ruu on cdma phone or other way round) then that explains the lack of capability.
Thanks for the tip. I ran the Froyo TELUS RUU.exe (should be the right type, as I have a Telus phone). It wouldn't work (in both main HBOOT screen and FASTBOOT screen). Gave me an "error 170". It could not connect to the phone, despite that I'm on Windows XP, that it says "Android Bootloader Interface" in Windows Device Manager, that it says "HBOOT USB PLUG" on the HBOOT screen when connected via USB, and that I am able to issue FASTBOOT commands from the PC. But I can't issue adb commands, so it appears I can only "partially" communicate with the phone from the PC.
Should I try CLEAR STORAGE, or could that fully brick my phone?
On the HBOOT screen, these are the status messages that load:
Loading...[PB99DIAG.zip]
No Image!
Loading...[PB99DIAG.nbh]
No Image!
Loading...[PB99IMG.zip]
No Image!
Loading...[PB99DIMG.nbh]
No Image or wrong image!
waynestir said:
if i'm not mistaken you can run the ruu and it should see the device if connected to pc with fastboot loaded.
as for trying to get back without losing data i'm new to all this so no idea
if you had run ruu on the phone and it was wrong type (i.e gsm ruu on cdma phone or other way round) then that explains the lack of capability.
Click to expand...
Click to collapse
USB Brick
For me, it sounds like a typical usb brick :/ I hope you still have rooted ROM. Search through this forum for unbricking guide.
Put the ROM.zip from the RUU on your SDCard but name it PB99IMG.zip and then boot with volume down again to enter HBOOT, it should give you the option to flash your phone back to factory default then.
HTC Desire Stuck on HTC logo - Recovery not Working - SOLVED!!
madcr0w said:
Put the ROM.zip from the RUU on your SDCard but name it PB99IMG.zip and then boot with volume down again to enter HBOOT, it should give you the option to flash your phone back to factory default then.
Click to expand...
Click to collapse
Thanks! I just tried that on the advice of another poster on another forum (before reading your reply), and that's the one and only thing that worked!
Especially when, after the RUU.exe wouldn't install, RECOVERY mode wouldn't work, nor adb, nor HTC Sync. Yes, I've lost my root access, but small consideration, considering I haven't lost my $500 investment! I'm sticking with stock now, as I'd rather not risk having a brick in the future.
As for what went wrong, I can't say for sure. But considering it took months after I had installed a ROM or otherwise modified the phone for problems to show up, I'm guessing it was probably the overclocking heating the chips. Which led to eventual random reboots during phone calls, and the eventual freezing of the boot screen, and subsequent inability of HBOOT to load PB99IMG.ZIP.
xda rocks, thanks to you and all those who took the time to reply.
sorry for delayed responce. I'm sure you had already found a solution by now but in the off chance you didn't.
you have to load fastboot not hboot.
from a power off state hold back button and power on phone. this will load fastboot and ruu will find device when run.
Cyanoid said:
Thanks for the tip. I ran the Froyo TELUS RUU.exe (should be the right type, as I have a Telus phone). It wouldn't work (in both main HBOOT screen and FASTBOOT screen). Gave me an "error 170". It could not connect to the phone, despite that I'm on Windows XP, that it o Image!
Click to expand...
Click to collapse
Fastboot will only work in Fastboot. ADB will only work when phone is booted and USB Debugging is on.
I don't know that as fact, I only know it from personal experience.
Use Fastboot to flash a new ROM, or at least a new recovery image. If you can get into Fastboot, you 'should' be able to fix your phone.
expza said:
Fastboot will only work in Fastboot. ADB will only work when phone is booted and USB Debugging is on.
I don't know that as fact, I only know it from personal experience.
Use Fastboot to flash a new ROM, or at least a new recovery image. If you can get into Fastboot, you 'should' be able to fix your phone.
Click to expand...
Click to collapse
+1 There is a good guide to fastboot commands on the android wiki:
http://android-dls.com/wiki/index.php?title=Fastboot
Should be a case of wiping system, data, cache, then flashing recovery image. Then boot into that and restore a backup or flash a rom.
Cyanoid said:
Thanks! I just tried that on the advice of another poster on another forum (before reading your reply), and that's the one and only thing that worked!
Especially when, after the RUU.exe wouldn't install, RECOVERY mode wouldn't work, nor adb, nor HTC Sync. Yes, I've lost my root access, but small consideration, considering I haven't lost my $500 investment! I'm sticking with stock now, as I'd rather not risk having a brick in the future.
As for what went wrong, I can't say for sure. But considering it took months after I had installed a ROM or otherwise modified the phone for problems to show up, I'm guessing it was probably the overclocking heating the chips. Which led to eventual random reboots during phone calls, and the eventual freezing of the boot screen, and subsequent inability of HBOOT to load PB99IMG.ZIP.
xda rocks, thanks to you and all those who took the time to reply.
Click to expand...
Click to collapse
can u plz help me frm with post u solved ur probs....i m stuck too
1st Post, got my htc desire this morning and after researching for a long time already knew i wanted to root my device.I followed the instructions on this site.[HOWTO] Root Your Desire In 1 Click With UnrEVOked! *UPDATED 20/7* - xda-developers I used unrevoked3, and rooted the device. no trouble Ive backed up the device with titanium backup. Placed cyanogen onto the 4gb sd card which came with the phone.Power off the device. Rebooted whilst holding the volume down button. Got the options up. Navigated to recovery and selected it with the power button. The screen goes blank. The o2 screen comes up saying welcome and thats it, it freezes. I have to pull the battery out of the back in order to reset the device and then it starts up perfectly normal. Tried accessing recovery mode using the clockworkmod but i get the same result.All of the points on the link above were followed. Im pretty much right at the bottom! still researching the net for the answer but im now in need of additional
Does your phone get hot and overheated during the htc logo? It did so to me and it turned out to that my CPU had melted and overheated. Take it to your retailer and they will fix it for free because it's not your fault, it's the phone that overheated.
Try this:
-download this with ur pc and rename it a PB99IMG.zip (not PB99IMG.zip.zip ok?)
-then put it on the root of ur sdcard (not in some folder) through an sd card reader
-ensure the battery is charged much than 30%..better more
-with the phone off (remove battery and put again) press and HOLD the volume down key and press (still holding the volume down key) and hold the power button..hold both and wait to enter in the hboot
-there wait a bit, and it will ask to u if u want apply the update, select yes with the volume keys and confirm with power button
awayra said:
1st Post, got my htc desire this morning and after researching for a long time already knew i wanted to root my device.I followed the instructions on this site.[HOWTO] Root Your Desire In 1 Click With UnrEVOked! *UPDATED 20/7* - xda-developers I used unrevoked3, and rooted the device. no trouble Ive backed up the device with titanium backup. Placed cyanogen onto the 4gb sd card which came with the phone.Power off the device. Rebooted whilst holding the volume down button. Got the options up. Navigated to recovery and selected it with the power button. The screen goes blank. The o2 screen comes up saying welcome and thats it, it freezes. I have to pull the battery out of the back in order to reset the device and then it starts up perfectly normal. Tried accessing recovery mode using the clockworkmod but i get the same result.All of the points on the link above were followed. Im pretty much right at the bottom! still researching the net for the answer but im now in need of additional
Click to expand...
Click to collapse
Just go to my troubleshooting guide, you'll probably find an answer there.
Send it back for warranty repair.
Sent from my Motorola Startac running Atari 2600 software!
@nhrsak - you save me, thanks very much!!
Did you try getting s-off with Revolutionary?
I had problems when i was s-on, but when i s-offed, everything went fine.
Have you tried flashing recovery.img via AndroidFlasher(from XDA)?
[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work
Hi guys,
I've watched the n00b video and been googling for the last few hours as well as reading through various pages on the XDA forum. I've found a lot of problems that are kinda similar and tried various solutions but don't seem to be quite getting there.
Basically I had Virtuous Affinity as the OS and clockworkmod installed (should be the most up to date versions of both, they were put on no more than a week ago) as well. I also had a backup of current OS and so on on the SD card, as well as the original zip of the rom.
I decide I want to give ICS a go and so I downloaded the betamod ICS and then loaded it. It asked me if I wanted to do a dalvik cache wipe, a dalvik cache + data wipe and a third option I don't recall. I went with the dalvik cache wipe (at the time I was under the impression that was the correct course of action) then put it back in my pocket while ICS installed.
I get my phone out of my pocket later and it's kinda stuck on what looks like (but logically isn't, I'm guessing it was meant to be a splash screen type thing while ICS installed or some such) a screensaver which just loops endlessly. The only thing you can really do is take the battery out and turn her on again, in which case you once again end up in the endless screensaver loop.
I've tried booting to recovery using volume - and the power button and unfortunately it just boots straight into the looping screensaver again.
Getting a bit worried and feeling adventurous I tried seeing what I could do with ADB, however the computer seemed unable to recognise that any device was connected with ADB devices not listing anything.
I've read up a lot and I'm at a loss as to what to do - there's a rom on the SD card and there also should have been a backup but I just can't get it into recovery.
I do have the ability to view the SD card on another device and interact with it, so if there's a potential SD fix, that's certainly not out the window.
But yeah, I'm clueless how to proceed here and very green at the whole rom business. Can anyone advise what I might try to do from here? I don't care what state I end up going back to, or if I lose my data, I can get all that back, I just want the phone in some semblance of basic operation.
I'll be keeping an eye on the thread, if I've left out any pertinent data ask away and thanks in advance for anyone with a clue how I can fix this mess .
EDIT: Post may be better off in ICS thread above and I do apologise if so, I would move it but I seem unable to delete it.
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
ik222 said:
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
Click to expand...
Click to collapse
I have, it doesn't work. I've left the battery out for a fairly long period. Volume - + power still just brings it back to the "screensaver" loop.
Thanks for the suggestion though.
Turn the phone off completely; pull the battery out for a bit then replace it and don't touch anything. Don't try to turn it on. Plug the phone by usb to your pc (still turned off). At the command prompt in the folder containing adb.exe type "adb reboot recovery" - the phone should power on and go to recovery where you can wipe properly and reflash whatever you want.
You should be able to boot to recovery using the volume down + power button combo (hold the volume-down key, then press and hold the power button and keep both held until you get to the bootloader menu); the only thing that's wrong with your phone is that you've flashed one ROM over another without wiping it first, so the ROM can't load but this shouldn't affect your bootloader or recovery.
Worst case you can flash a RUU which will restore it to the official firmware; you'll then need to re-root and re-install a recovery image to be able to flash custom ROMs again.
Very helpful post, thanks! I'll try all that and see how I go, I'll post if I still have trouble.
Yeah I dunno why I can't boot to recovery it's weird. The volume button wasn't working, so I removed it and am pressing in the volume down portion of the volume button with a pen while holding down the power button. It's possible perhaps I'm not successfully depressing volume down, but I'm 99% sure I am and that that's not it. I am however doing it as you and other guides advise, depress volume down, hold it and then depress power and hold both for about three seconds, no joy!
Anyway, as said, I'll try what you're recommending and see how I go. Thanks!
hopscotchjunkie said:
At the command prompt in the folder containing adb.exe type "adb reboot recovery"
Click to expand...
Click to collapse
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Ethicistabdiel said:
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Click to expand...
Click to collapse
Yeah that was what I meant; I've got a feeling that that only works when the phone is powered off if you had USB debugging activated on the phone beforehand, so if that's not working that might be why.
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Accidental double post, sorry.
You need to try get into recovery mode, where you can do a full wipe and see if that fixes anything.
Firstly, remove your battery then re-install it, your phone should still be turned off at this stage. Press and hold the volume down button, then additionally press and hold the power butter, until something appears on the screen. If the bootloader appears, you can then boot into recovery from there.
If the above fails to work, report back with your results and hopefully something else will be suggested.
Ethicistabdiel said:
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Click to expand...
Click to collapse
Your only other option to get into recovery is the volume-down/power-on combination. Like I said, I can't think why that's not working unless it's related to your missing volume button (maybe it's not maintaining a constant pressure on the button when you're using whatever to press through the hole).
If you still can't get that to work, I would suggest finding a stock RUU and flashing that. It's an .exe file that runs from your PC and will return your ROM, bootloader and radio back to stock. Obviously that means you'll lose root and your custom recovery so you'll need to do all that again from scratch. There's a sticky in the dev section with a link to a thread with various RUUs (it's named something along the lines of "shipped & test ROMs" - I'll check that and link to it once I've dragged myself out of bed to the computer). You'll lose all your data, but if you took a backup beforehand you can restore that once you're back up and running.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
http://forum.xda-developers.com/showthread.php?t=824357&page=5
Guessing you mean that as far as the ruu thread. Am downloading a stock rom atm, with shaped internet till tomorrow, meh! Will see how I go. Have a feeling phone was probably Vodafone branded at stock though, so that could make for extra fiddling but yeah, fingers crossed.
If you are able too install a stock-rom you can work from their than install 4EXT recovery
touch than you doen't need the volume buttons.
I downloaded the most recent stock rom on the link above. When I try to install it though, phone off or on, it advises a USB connection error. Is this likely to be because I originally had vodafone stock and need to make a gold card, or should it still at least be recognising it? It does advise not to run any programs on the phone or anything when while installing the update, but of course, as long as my phones turned on it's stuck on the damned screensaver loop.
http://forum.xda-developers.com/archive/index.php/t-841890.html
Gonna give that a go, fingers crossed!
D'oh, just found out my mobile was Three at stock and not Vodafone, the search continues .
Gah, I'm about tearing my hair out here, I want my damned phone back . Stuck using a $79 Huwawei Vodafone thing at the moment and it's so so so awful.
Anyway. I was under the impression that making a goldcard would mean I could RUU a non-Three stock rom on the phone. I made a goldcard following these instructions; http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
Then I turned the phone on as the RUU advises, (meaning it's scrolling through the feckin' "screensaver") and start the process and once again get a USB connection error.
What's the better process at this stage, try and take it back to Three stock? I don't see how I can at the moment, the only Three stock I can find seems to be rom, not RUU, meaning I'd need to load from the phone, which I can't due to no recovery. Or should I keep trying to get the goldcard thing to work, maybe try some different RUU's or something?
I'm open to any other suggestions as well. Had a bit more of a fiddle around with my volume down button, no matter what I do though, I can't get recovery mode. Always boots first to the white HTC screen and then starts the infernal "screensaver" loop.
Ethicistabdiel said:
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
Click to expand...
Click to collapse
How come the volume down button be broken. When you were using Affinity Rom weren't you able to use your volume button for music. Remove SD card from phone then press "First - Volume down gently for 2 sec" & press-hold power button when it goes into bootload place your sd card back select option "REBOOT RECOVERY". I think your panicking too much just be patient nothing is wrong, i think your just hurrying it up...
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Ethicistabdiel said:
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Click to expand...
Click to collapse
The only option i can think of is "Fix your volume button from your nearest Service centre". Without that you cant do anything. I am Sorry....
Coming from a phone with microSD extension, I had never encountered such an issue:
I bought this phone with a stock 4.2 Rom installed and tried to install a custom Rom. I first installed the latest version of touch recovery (tried it and it seemed to work fine) and did a backup using the default settings. Then I erroneously chose to format system and data, thinking that I could then "install from zip". Strangely, these steps deleted everything in the /sdcard directory and I couldnt select "external SD" (because the phone isnt equipped with it anyways?). Then I made a second mistake and restarted the phone, despite the message warning that I no longer had an OS installed. I took the battery out, and then held the power down while pressing the power button. The phone couldn't get into recovery, but instead showed a screen with the android logo, a large "Start" sign above it, and "Downloading...", "Do not turn off target !!" below it. Pressing the power button now got the phone to show just "Google" and a lock logo under it. The PC (windows 7) can not detect the phone throughout the process.
I tried the latest tool kit and samsung's USB driver but couldnt get the phone recognized by the PC.
Does this mean that the phone is doomed???
Please help!!!
Trent
Relax, it's not easy to 'doom' your Nexus. Especially with all the hard-workers in XDA
Try accessing Recovery mode by holding down BOTH vol up + vol down, as well as power. Holding just vol down + power is 'Download Mode', and at the least you can get to this. Means your phones far from doomed
Thanks a lot for the reply!
As a matter of fact, I also figured out how to get back to recovery (if only I had read your post earlier, my pain would've been much less!). But the problem remains that I can not get a target ROM onto the phone, since: 1. whatever I did seemed to have gotten rid of the nand backup supposedly stored in /data/media/TWRP/BACKUPS/ (I'm using TWRP V. 2.3.2.1). 2. I can not get my PC(or Mac, for that matter) to recognize the phone or the internal storage.
Any pointer from here?
Thanks again!!!
Trent
You can download a factory image and install with fastboot. It's quite easy and instructions are readily available on this forum. You can then install a custom ROM afterwards if stock is not your thing.
Found the answer finally!
It's the adb push method. Basically, it's to install adb drivers and execute a few commands via the command window. Not too bad... Don't know much about fastboot yet though ... If anyone else needs more details, please PM me (to save public bandwidth).
Thanks a lot anyways, whpnhp and jocalderone!!!
Trent