Related
Okay i have a big problem...
I have rooted my device, however didn't run the ENG build, so my recovery is dependent on the pushing of the update.zip...
I flashed the myfroyo5 after pushing the update.zip... and ADB worked great, found the device in HBOOT and recovery.
Now after flashing this ROM, when i try and reboot back HBOOT no devices found.. however when i'm at the home screen with Myfroyo5 booted up, it sees the device..
Now i can't run any update, or get into clockwork recovery because i can't push the update.zip, because ADB can't see my device....
Please help! Any idea how i can get it to see my device with Myfroyo5? Otherwise i'm stuck with Myfroyo5 and can't reverse or do anything with it
Before all i did was change the option from device storage, to charge only, and that's how it worked...
again any ideas are appreciated!
wow 58 views and no one has any ideas? Please help!
Try turning on USB debugging mode?
Yes its always on, always check marked
I feel like I did have a similar problem at one point, but I don't remember how I resolved it. Sorry.
gee maybe you should have flashed the eng build as everyone was told to do when they rooted their slide. try a dozen different large and small SD cards, i don't really think that is what makes it work but others seem to disagree and maybe once you swap them out you'll get lucky. but first i would try flashing the eng build
tubaking182 said:
gee maybe you should have flashed the eng build as everyone was told to do when they rooted their slide. try a dozen different large and small SD cards, i don't really think that is what makes it work but others seem to disagree and maybe once you swap them out you'll get lucky. but first i would try flashing the eng build
Click to expand...
Click to collapse
Must your replies always, ALWAYS have some snarky bit about how the person asking the question screwed up?
Humans are prone to error. You have valuable insight but beating someone's ego up before you give it really offsets your kindness.
Sent from my T-Mobile myTouch 3G Slide using XDA App
They don't always have snarky bits, but when 90% of problems are caused by not following directions then it apparently needs to be retold, I help a lot and I gave ideas to try here. Odds are he can still flash the eng build and then get into clockwork, but not following directions causes issues like this.
Sent from my T-Mobile myTouch 3G Slide using XDA App
I see your point but, as I recall, the ENG build came after root had been put out there for a day or so. I'm also pretty sure it came after SlideMeRoot1.
Things like this, along with simple mistakes, can cause these errors. You are helpful but I just find the "hey, dummy" tone to be overkill.
Not everyone who screws up is out to **** up your day, ya know? I've been having my own ENG build problems because I made a mistake. It doesn't mean I don't know how to follow directions, it just means I made a mistake, the way every human on the planet does.
I apologize, as well, because my own real life smiley fun tone doesn't translate well to the forum. IE: you good kid.
tubaking182 said:
They don't always have snarky bits, but when 90% of problems are caused by not following directions then it apparently needs to be retold, I help a lot and I gave ideas to try here. Odds are he can still flash the eng build and then get into clockwork, but not following directions causes issues like this.
Sent from my T-Mobile myTouch 3G Slide using XDA App
Click to expand...
Click to collapse
Sent from my T-Mobile myTouch 3G Slide using XDA App
well first off.. i did follow directions... and it didn't work... and i've flashed multiple roms by just re-doing the ota.zip then the update.zip push, to get me into clockwork, until i flashed myfroyo5
which does not allow me to "charge only" which is why ADB doesn't allow to recognize my device in HBOOT/Recovery.
On the contra-ire i do know what i'm doing however a little bit of "knowledge" to point out maybe something that will fix an issue i have would be great.
Now i'm running myfroyo5, the device is seen by adb when the phones booted up, however upon reset to HBOOT/Recovery no devices are found. I've tried putting ENG build on my Sdcard, and HBOOT doesn't see it, also, i've tried pushing flash_image to /data/local, and mtd0.img to /data/local, and the files will not move.
That is part of my problem i'm assuming, i'll try another SD card to see if it will fix it, but i'm not sure its something that simple... but who knows, right?
javolin13 said:
well first off.. i did follow directions... and it didn't work... and i've flashed multiple roms by just re-doing the ota.zip then the update.zip push, to get me into clockwork, until i flashed myfroyo5
which does not allow me to "charge only" which is why ADB doesn't allow to recognize my device in HBOOT/Recovery.
On the contra-ire i do know what i'm doing however a little bit of "knowledge" to point out maybe something that will fix an issue i have would be great.
Now i'm running myfroyo5, the device is seen by adb when the phones booted up, however upon reset to HBOOT/Recovery no devices are found. I've tried putting ENG build on my Sdcard, and HBOOT doesn't see it, also, i've tried pushing flash_image to /data/local, and mtd0.img to /data/local, and the files will not move.
That is part of my problem i'm assuming, i'll try another SD card to see if it will fix it, but i'm not sure its something that simple... but who knows, right?
Click to expand...
Click to collapse
Just use CR new root method for the ota update and then follow the steps to flash ENG build. wouldnt that work? cause its unneccessary for the device to be recognized in hboot in adb that way =\ just guesing
i would do all that too.... you know i think the issue is the copying the files over... none of them are actually moving where they need to go!...
And when i try to do it manually the folder says "read only file system" and when i try to push files it says "1188 KB/s <0 bytes in XXXX.000s>
so none of the image files are moving over to allow me to flash ENG build... i swapped different SD cards and now i can flash the ENG build, but i cant move the files to /data/local before i do that, so right now its pointless to flash it...
javolin13 said:
i would do all that too.... you know i think the issue is the copying the files over... none of them are actually moving where they need to go!...
And when i try to do it manually the folder says "read only file system" and when i try to push files it says "1188 KB/s <0 bytes in XXXX.000s>
so none of the image files are moving over to allow me to flash ENG build... i swapped different SD cards and now i can flash the ENG build, but i cant move the files to /data/local before i do that, so right now its pointless to flash it...
Click to expand...
Click to collapse
do u have root in the shell script when u try to push the files over?
yes i do, that's whats really weird... i do adb shell, and i get #
when i do it the cat way, it does what it needs to, yet when i go search for the files using linda file manager they're still not there...
i dont want to flash eng build and it not work...
javolin13 said:
yes i do, that's whats really weird... i do adb shell, and i get #
when i do it the cat way, it does what it needs to, yet when i go search for the files using linda file manager they're still not there...
i dont want to flash eng build and it not work...
Click to expand...
Click to collapse
i mean u could always just unroot and start from square one
can't unroot if my device is not seen with adb in hboot / recovery
javolin13 said:
well first off.. i did follow directions... and it didn't work... and i've flashed multiple roms by just re-doing the ota.zip then the update.zip push, to get me into clockwork, until i flashed myfroyo5
which does not allow me to "charge only" which is why ADB doesn't allow to recognize my device in HBOOT/Recovery.
On the contra-ire i do know what i'm doing however a little bit of "knowledge" to point out maybe something that will fix an issue i have would be great.
Now i'm running myfroyo5, the device is seen by adb when the phones booted up, however upon reset to HBOOT/Recovery no devices are found. I've tried putting ENG build on my Sdcard, and HBOOT doesn't see it, also, i've tried pushing flash_image to /data/local, and mtd0.img to /data/local, and the files will not move.
That is part of my problem i'm assuming, i'll try another SD card to see if it will fix it, but i'm not sure its something that simple... but who knows, right?
Click to expand...
Click to collapse
I had the same problem just about and used the following thread. http://forum.xda-developers.com/showthread.php?t=710056 <-- BIG THANKS to Beartard for taking the time to type this all out. It worked just fine. I picked it up from - Installing the Engineering ROM - I kept my old update.zip file on the root of my sd card, and I got everthing back to normal, and everything works like new. Hope this helps
Suntar said:
I had the same problem just about and used the following thread. http://forum.xda-developers.com/showthread.php?t=710056 <-- BIG THANKS to Beartard for taking the time to type this all out. It worked just fine. I picked it up from - Installing the Engineering ROM - I kept my old update.zip file on the root of my sd card, and I got everthing back to normal, and everything works like new. Hope this helps
Click to expand...
Click to collapse
Thanks for the idea, but flashing the ENG build is pointless unless i can push the flash_image, and mtd0.img to /data/local... which for some reason my phone will not allow me to do this part;
Code:
type "adb push flash_image /data/local" and hit enter.
2. Type "adb push mtd0.img /data/local" and hit enter.
[Edit: I've now resolved this issue. Thanks to all who helped. Please see end of thread for my solution. I've made some edits below too. When things looked bad, the solution was to remove the microSD card, copy and load a more reliable PC36IMG.zip (there are a huge number out there), and only then could I use adb when the red triangle was present. Note that just renaming stuff randomly or worrying about the USB cable isn't a proper way to come up with a solution even though I did it also (and that may be the case for some units but it can't be the general problem or solution). I'd guess there's a huge amount of misinformation out there and some people may have tried random stuff but it looks like from playing with all this, there is a method to the madness of how phone and the adb communicate, as well as how the phone loads, and once you UNDERSTAND HOW that process, all this stops being so much of a black magic.
Note that the problem I had was because I used an outdated set of instructions. Here are the ones that worked for me in the end:
http://forum.xda-developers.com/showthread.php?t=829045
Thanks to all who did reply to my message.
]
--------
I've tried literally everything I've read to get out of my red triangle situation so please help if you can. This is not your standard "hold volume up and power button" response.
I was trying to get to root using the method at evo4g.me.
And I got a red triangle after the first application of the PC36IMG.ZIP. I then held the volume up and power button and, I get a blue lettered screen with 4 options:
reboot system now
apply sdcard:update.zip
wipe data/factory reset
wipe cache partition
Well, I've seemingly tried everything but I can't seem to get past this screen. I've pulled the battery out and rebooted, I go back to the above screen. Option 1 above gets me back to the same spot. Option 2 says it can't find sdcard/update.zip. I did option 3 but it does that and turns off and on and comes back to this same position. Even when I try to hold the volume button down. When I try to access this using adb, I get "device offline".
I can take the battery out, hold the volume down button, and then power on, and it takes me the through the same steps as before and I don't seem to have control over the choice of whether it should load the PC36IMG.ZIP file or not (i.e., the menu I see before it doesn't to be controllable by me).
So I'm at a loss. I really would like to finish this process and get to root, which shouldn't be too hard in my view but here I am.
I could move the SD card elsewhere and put an update.zip file on there but I'm not sure what to do here exactly so I can recover (and hopefully with root). Is this the correct thing to be thinking about? Move the SD card to another device, replace the .ZIP file, and then go from there? Is there a way to do this without moving the SD card?
[Edit: this is indeed what I did in the end. I found the correct PCIMG.zip file by trial and error.]
Thanks a lot!
BTW, I backed up all my apps on my sdcard so I should be fine right? I'm not sure what I'd need to do reinstall them.
[Edit: I lost some public keys, etc. with app reinstalls but I just had too many apps doing backups in different places and wasn't matching the right app restore to the right location in part.]
--
Backgrround: I'm new to the Evo 4G and in general new to doing stuff like rooting phones and the like, so please forgive me if my questions (or actions) or too naive. I have been using Unix systems all my life and Linux when there were fewer than 100,000 users of it (back in 1992-1993) and am extremely comfortable with it and do all my science (work) exclusively with Linux.
ramdom said:
I've tried literally everything I've read to get out of my red triangle situation so please help if you can. This is not your standard "hold volume up and power button" response.
I was trying to get to root using the method at evo4g.me.
And I got a red triangle after the first application of the PC36IMG.ZIP. I then held the volume up and power button and, I get a blue lettered screen with 4 options:
reboot system now
apply sdcard:update.zip
wipe data/factory reset
wipe cache partition
Well, I've seemingly tried everything but I can't seem to get past this screen. I've pulled the battery out and rebooted, I go back to the above screen. Option 1 above gets me back to the same spot. Option 2 says it can't find sdcard/update.zip. I did option 3 but it does that and turns off and on and comes back to this same position. Even when I try to hold the volume button down. When I try to access this using adb, I get "device offline".
I can take the battery out, hold the volume down button, and then power on, and it takes me the through the same steps as before and I don't seem to have control over the choice of whether it should load the PC36IMG.ZIP file or not (i.e., the menu I see before it doesn't to be controllable by me).
So I'm at a loss. I really would like to finish this process and get to root, which shouldn't be too hard in my view but here I am.
I could move the SD card elsewhere and put an update.zip file on there but I'm not sure what to do here exactly so I can recover (and hopefully with root). Is this the correct thing to be thinking about? Move the SD card to another device, replace the .ZIP file, and then go from there? Is there a way to do this without moving the SD card?
Thanks a lot!
BTW, I backed up all my apps on my sdcard so I should be fine right? I'm not sure what I'd need to do reinstall them.
--
Edits based on trying to fix this: when I do `adb devices`, I get:
List of devices attached
HT0B6HL05287 offline
--
Backgrround: I'm new to the Evo 4G and in general new to doing stuff like rooting phones and the like, so please forgive me if my questions (or actions) or too naive. I have been using Unix systems all my life and Linux when there were fewer than 100,000 users of it (back in 1992-1993) and am extremely comfortable with it and do all my science (work) exclusively with Linux.
Click to expand...
Click to collapse
That is the stock recovery you are seeing there, does it let you do anything at all in the bootloader? If you can get it into fastboot mode you can fix it from there.
I rooted using regaw's instructions also, and also got that damn triangle, lol. Pretty sure all I did was reboot to bootloader and let it update the PC36.img again to get out of it.
xHausx said:
That is the stock recovery you are seeing there, does it let you do anything at all in the bootloader? If you can get it into fastboot mode you can fix it from there.
Click to expand...
Click to collapse
Yes, I believe so. I can let the PC36IMG.ZIP reload again and then AFTER that I can say "no" to the update and then "no" to reboot devices and I can get into a menu that says:
FASTBOOT
RECOVERY
CLEAR STORAGE
SIMLOCK
HSB USB
From there I can select FASTBOOT and head into another menu that says:
BOOTLOADER
REBOOT
REBOOT BOOTLOADER
POWER DOWN
Trying BOOTLOADER gets me through the same HBOOT cycle where the PC36IMG.ZIP is reloaded and asked to be applied. Trying REBOOT gives me a white HTC screen (unless I need to wait a while).
Thanks! I assume I need to pull the SD card out, load it on my computer through another source, and then remove the PC36IMG.ZIP file and then replace it with something else that I can use to get rooted? Or will just removing the PC36IMG.ZIP file do it?
I'm also looking to achieve root so if I am going to the trouble of removing the SD card and putting it back, I'd like to know if if there's another PC36IMG.ZIP that'll let me have a nice version of the HTC evo that is rooted.
--Ram
I know a few people who have recently purchased EVOs and they still have Hardware version 3 and Hboot .97
what versions do you guys have on your phones?
If the hboot is still .97 you can used unrevoked forever for a full root and nand unlock.
if higher there is a tutorial on these forums for Hboot 2.02.
chris66 said:
I rooted using regaw's instructions also, and also got that damn triangle, lol. Pretty sure all I did was reboot to bootloader and let it update the PC36.img again to get out of it.
Click to expand...
Click to collapse
How did you do it?
Tuffgong4 said:
I know a few people who have recently purchased EVOs and they still have Hardware version 3 and Hboot .97
what versions do you guys have on your phones?
If the hboot is still .97 you can used unrevoked forever for a full root and nand unlock.
if higher there is a tutorial on these forums for Hboot 2.02.
Click to expand...
Click to collapse
I have:
SUPERSONIC EVT2-3 SHIP S-ON
HBOOT-2.02-0000
TOUCH-PANEL-ATMELC-03_16ac
RADIO-2.15.00.09.01
Oct 14 2010, 19:14:47
I assume the tutorial you're referring to is here:
http://forum.xda-developers.com/showthread.php?t=829045
But I'm not sure how to get out of this particular PC36IMG.ZIP (gotten from evo4g.me) and replace it with the PC36IMG.ZIP posted in the above URL above easily, since I can no longer access this device using adb. Unless I am missing something obvious.
Well, I'm learning a lot! Thanks!
I do agree having root on these systems will be fantastic. I don't understand why it's not just a ready option. Things like tethering, etc. should be a given and built into the $10 cost or something else of the network. I'd like to port things like csh on there, and have a powerful terminal like I can get in the Mac OS X. Is there any way this is possible at all? We can get bigger and bigger microSD cards right? An entire stripped down Linux system can fit in a few gigs (but I want to be able to use it as a phone too).
--Ram
Went backward in the directions.
This the whole post that I used, pretty sure I just went backward and started again, it did take a seemingly HUGE amount of time the first time thru flashing the PC36.img
http://forum.xda-developers.com/showthread.php?t=765496
PULL THE SD CARD and put the image on the root? , lol
chris66 said:
Went backward in the directions.
This the whole post that I used, pretty sure I just went backward and started again, it did take a seemingly HUGE amount of time the first time thru flashing the PC36.img
http://forum.xda-developers.com/showthread.php?t=765496
PULL THE SD CARD and put the image on the root? , lol
Click to expand...
Click to collapse
The instructions at the above URL are what I used to get to this place with the red triangle that I can't seem to get out of. I can no longer access the phone using adb so I can't push anything. I can't access the phone through my computer right now once it has become stuck at the red triangle, this is my main issue. No access. Nothing. It just says "error: device offline" no matter what I try.
You don't think the SD CARD strategy will work?
This is where I scared the **** outta myself.....
"If this doesn't work (ie the PC36IMG.zip does NOT load) backup all of your sdcard contents onto your computer, reformat your sdcard to FAT32, redownload the PC36IMG.zip, and drag and drop it onto the sdcard, then reboot into the bootloader and try again. This should fix the issue."
It worked for me, but I don't know what hardware version and all you have.
ramdom said:
The instructions are the URL are what I used to get to this place with the red triangle that I can't seem to get out of. I can no longer access the phone using adb so I can't push anything. I can't access the phone through my computer right now once it has become stuck at the red triangle, this is my main issue. No access. Nothing. It just says "error: device offline" no matter what I try.
You don't think the SD CARD strategy will work?
Click to expand...
Click to collapse
just pull the sd card out of the evo (behind the battery) and put the new img on the root of the card.
chris66 said:
This is where I scaref the **** outta myself.....
"If this doesn't work (ie the PC36IMG.zip does NOT load) backup all of your sdcard contents onto your computer, reformat your sdcard to FAT32, redownload the PC36IMG.zip, and drag and drop it onto the sdcard, then reboot into the bootloader and try again. This should fix the issue."
It worked for me, but I don't know what hardware version and all you have.
Click to expand...
Click to collapse
Me too, but I pay for the extra warranty that's supposed to cover nearly everything, which I think should cover this.
So from the above instructions, am I to understand that I remove the sdcard out and clean it out in my computer and install a new PC36IMG?
Should I try the one from here? Even here, there are like 3 versions:
http://forum.xda-developers.com/showthread.php?t=829045
Sorry for all the questions. Normally I'd hack and figure this out without even googling it but after googling it, the amount of stuff out there is enormous which is throwing me off. I think I have like 10 versions of the PC36IMG and not sure which to go with next that'll not destroy everything and give me root! Crazy.
Tuffgong4 said:
just pull the sd card out of the evo (behind the battery) and put the new img on the root of the card.
Click to expand...
Click to collapse
Thanks a lot. Pulling the evo card was easier than I thought it would be. Which particular one? I'm looking here:
http://forum.xda-developers.com/showthread.php?t=829045
Should I just manually copy all these files over to the sdcard and then reboot and see what happens? I guess I'll try that. Thanks.
Thanks guys!
--Ram
Well, I solved this problem and am now enjoying root. Thanks to all who helped. I followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=829045
But I still couldn't get past step 10. I even read the FAQ and followed the renaming suggestions (this wasn't the issue but I did it anyway) and it still didn't work. Basically the problem was that I wasn't even able to get to the shell even though I was able to use adb to push files (weird?).
So I was playing around with the EVO-recovery.zip (http://www.knowyourcell.com/htc/htc-evo-4g/evo-4g-guides/463925/how_to_root_the_htc_evo_4g.html) and ran the recovery-linux.sh script, which then put me into the green recovery screen. The rest was straight forward after that (as per the instructions at the URL above). So perhaps the difference of which adb to use was what it was, since that zip file comes with its own adb.
I am now rooted. Now what?
My wi fi doesn't seem to work, and neither does the google wireless tethering app, which is one of the reasons I wanted to root. When I run "adb shell" I now get a "#" instead of a "$" so I assume this (among other things, including the S-OFF) means I am rooted. So no wi-fi, did I trash something?
[Edit: I fixed this by installing the fresh ROM; thanks chris66 and others who helped!]
I'm just using the stock ROM provided from the URL above. Not sure what the best one to use is and how to use it.
[Edit: Stil no idea. Way too many ROMs out there. It's crazy. Fresh seems to have a good rep. It works pretty well, after one week.]
I also backed up all my apps on my sdcard, is there a way to restore them in one quick fell swoop instead of opening them one by one?
[Edit: I figured out how to do the multiselection option and apply it apps. A good file manager will do the backups for you. I went from ASTRO to ES File Explorer. Latter looks slightly cleaner. Probably better ones out there.]
Thanks to all who helped! I am excited about playing around with all this further. Only PITA is reconfiguring everything again the way I like it.
[Edit: Favourite apps are ConnectBot; Android Wireless Tether; AndroidVNC; DropBox; ES File Explorer; System Panel; --- from Ubuntu, I ADB to access stuff at the prompt which when having a # is really really powerful. Maybe I was wrong but before I put the new ROM on I didn't think the "more" command was available.]
Cool, try superuser and the wifi app from the market. Flash almost any of the newer roms, and they're already both usable, wifi and usb.
Sent from my PC36100 using XDA App
I do not know why you say this...
MOD EDIT: Rooters beware. Proceed with extreme caution, as these are highly uncharted waters.
Hi,
I am here to provide you a new method in rooting your xoom, it does not require to flash the decrypted boot.img image.
I have tried it only on my Wifi XOOM, which is a UK version. (With a Japan version of ROM, downloaded from Motodev and upgrade to 3.1)
***EDIT***
I have also tried on a HK 3g xoom (which shows MZ601 in MTP but MZ602 in fastboot). It works without any problem, and internal storage preserved untouched.
===============================================================
I am NOT a xoom developer, nor a rom cook. I am just a user of xoom, which know
a little on developing and are willing to try new things.
So, I can not be sure that the method below works on your device. By following the
things below, your xoom may have a chance to brick.
I am not responsible for any brick or mulfunction device.
===============================================================
To root your xoom, you should start with flashing your device with the clockworkmod recovery (Please refer to the post by solarnz).
After flashing the clockworkmod recovery, do the following.
1. Download the attached ROOT.zip, place it on the root directory of the external sd card, and rename it to update.zip
2. Restart your device to the recovery by:
Type "adb reboot recovery" from your pc
OR press volumn down ~2 seconds after the motorola logo appears when the device starts,
then volumn up when "-->Android recovery" appears.
3. Apply the update in the recovery.
That's it. Your device should be already rooted.
=======================================================================
I am not the inventor of the method, I think about this since I have a Samsung i9000,
and the method of rooting the i9000 is by applying a update.zip file.
I have created the ROOT.zip file by changing the i9000 root zip file with the newer su and superuser.apk (From here: http://forum.xda-developers.com/showthread.php?t=1010568)
I have also changed the updater-script in order to let the updater mount the correct partition for the update.
I am not sure if this update applies to other devices (especially for the 3g ones). This should work if the system partition have name "/dev/block/platform/sdhci-tegra.3/by-name/system".
I would like to thank solarnz for providing the clockmodwork recovery for xoom,
the one who invented the method of rooting the i9000 with a update.zip (I cannot find who make that, sorry...),
and also Xaositek for providing the su and superuser.apk files (I am too lazy to find it by myself...).
========================================================================
That's all. Please try on your device (especially for those stock 3.2) if you would like to take some risk, and report if it is success or not.
Thanks.
eddielo said:
Hi,
I am here to provide you a new method in rooting your xoom, it does not require to flash the decrypted boot.img image.
I have tried it only on my Wifi XOOM, which is a UK version. (With a Japan version of ROM, downloaded from Motodev and upgrade to 3.1)
===============================================================
I am NOT a xoom developer, nor a rom cook. I am just a user of xoom, which know
a little on developing and are willing to try new things.
So, I can not be sure that the method below works on your device. By following the
things below, your xoom may have a chance to brick.
I am not responsible for any brick or mulfunction device.
===============================================================
To root your xoom, you should start with flashing your device with the clockworkmod recovery (Please refer to the post by solarnz).
After flashing the clockworkmod recovery, do the following.
1. Download the attached ROOT.zip, place it on the root directory of the external sd card, and rename it to update.zip
2. Restart your device to the recovery by:
Type "adb reboot recovery" from your pc
OR press volumn down ~2 seconds after the motorola logo appears when the device starts,
then volumn up when "-->Android recovery" appears.
3. Apply the update in the recovery.
That's it. Your device should be already rooted.
=======================================================================
I am not the inventor of the method, I think about this since I have a Samsung i9000,
and the method of rooting the i9000 is by applying a update.zip file.
I have created the ROOT.zip file by changing the i9000 root zip file with the newer su and superuser.apk (From here: http://forum.xda-developers.com/showthread.php?t=1010568)
I have also changed the updater-script in order to let the updater mount the correct partition for the update.
I am not sure if this update applies to other devices (especially for the 3g ones). This should work if the system partition have name "/dev/block/platform/sdhci-tegra.3/by-name/system".
I would like to thank solarnz for providing the clockmodwork recovery for xoom,
the one who invented the method of rooting the i9000 with a update.zip (I cannot find who make that, sorry...),
and also Xaositek for providing the su and superuser.apk files (I am too lazy to find it by myself...).
========================================================================
That's all. Please try on your device (especially for those stock 3.2) if you would like to take some risk, and report if it is success or not.
Thanks.
Click to expand...
Click to collapse
How do you flash cwm if your device if locked? Also the purpose of the rooted boot.img is to allow you to mount your device for adb commands.
Sent from my PG86100 using Tapatalk
yeah no offense but this sounds a little sketch... I see you make a quote at the bottom asking people to report success if they try... I personally would not try this.
Unlocking and rooting is really not that hard and not very time consuming using current methods
Of course, for installing CWM, you have to unlock your device by using "fastboot oem unlock", but that will not brick your device anyway.
For this method, you do not need to issue adb commands to root your device, so no need to have a modified boot.img.
Also, for the current rooting methods, it is not 100% work on some device (like the HK 3g version, which reported missing of internal storage after rooting with currently available method), I would like to see if this work on that.
Rooters beware. Proceed with extreme caution, as these are highly uncharted waters.
eddielo said:
For this method, you do not need to issue adb commands to root your device, so no need to have a modified boot.img.
Click to expand...
Click to collapse
I think you missed my point. Rooted boot.img isn't used for rooting. Its used for adb commands like adb remount. Say i want to adb push a file to my xoom, ls a directory on my xoom, or adb rename system files. Those are all reason you need the rooted boot.img.
Sorry, this is not a rooting method. All what this is doing is flashing su, busybox and Superuser.apk.
There is more to rooting a device than this. You also need an insecure boot image.
I am sorry if I do not catch the real meaning of rooting a device.
What I think of rooting is to let my device, starting from everything stock, untouched, to a state that applications that need root, like Titanium backup or root explorer, works without problem.
I have tried on my two devices with this method, titanium backup works perfectly, root explorer can remount the system partition to rw and can successfully copy files and delete files from that.
The insecure boot.img image, as far as I know, provides everyone to use "adb remount" and make changes to the system directory. But my method do not need adb in copying the binaries and chmod them. You may call it flashing, but after that, su works without problem.
Please, try it first. If you think it is not a method of rooting, I am sorry about that.
Actually guys, don't dismiss him just yet, over in the Galaxy S II forums we only flash insecured images long enough to root the OS then flash back to a secure one, so you have root access but no remount or system r/w.
It's a (fairly) legitimate method and is exactly how I rooted my xoom this time round, well not exactly, I did it like this:
unlock
flash solarnz CWM
adb mount system r/w
push su and busybox
reboot
install superuser from market
done
This is how most people run their GSII and means you can use root apps but no insecure boot image (because the GSII shows a warning on every boot with insecure images and keeps a binary flash counter, cheeky samsung).
This will at least get you to the point where you can su from within android and dump your boot image to modify it yourself, which is what I just did to update my Euro 3G root guide.
So does this mean just "rooted".....like can't flash a rom?
Sent from my Xoom using XDA Premium App
roughneckboren said:
So does this mean just "rooted".....like can't flash a rom?
Sent from my Xoom using XDA Premium App
Click to expand...
Click to collapse
Rooting has nothing to do with installing a rom. To install a rom, you just need to unlock and fastboot flash CWM. This guide in noway helps you flash a rom.
alias_neo said:
Actually guys, don't dismiss him just yet, over in the Galaxy S II forums we only flash insecured images long enough to root the OS then flash back to a secure one, so you have root access but no remount or system r/w.
It's a (fairly) legitimate method and is exactly how I rooted my xoom this time round, well not exactly, I did it like this:
unlock
flash solarnz CWM
adb mount system r/w
push su and busybox
reboot
install superuser from market
done
This is how most people run their GSII and means you can use root apps but no insecure boot image (because the GSII shows a warning on every boot with insecure images and keeps a binary flash counter, cheeky samsung).
This will at least get you to the point where you can su from within android and dump your boot image to modify it yourself, which is what I just did to update my Euro 3G root guide.
Click to expand...
Click to collapse
Without an rooted boot.img your recovery will get wiped out every time you boot the OS.
So will this let you make a titanium backup of your data? That way you could recover your data after using the regular unlock method that erases everything?
silvinoa said:
So will this let you make a titanium backup of your data? That way you could recover your data after using the regular unlock method that erases everything?
Click to expand...
Click to collapse
Yes and NO...
Yes this method will allow you to run titanium backup. But to use this method you have to unlock, which erases everything.
[HOWTO] ClockworkMod Recovery & TWRP - Upgrade/Downgrade (Touch/Non-Touch Recovery)
IF YOU TRASH YOUR PHONE USING THIS PROCEDURE, THEN IT IS A VERY GOOD INDICATION YOU ARE AN IDIOT AND SHOULD NOT BE FLASHING ANY ROMS NOR PARTICIPATING ON THESE FORUMS. . . . JUST SAYIN'. . . .
Please be VERY careful when using this method as you can brick your phone. Make sure you triple check the file you downloaded is the right size and placed in the right area, but most importantly that the command lines you type are exactly right. If you are not comfortable using this method, then please do not and go find a flashable version of these recoveries.
I've posted a procedure to format/'flash' your recovery while on your phone in one of the threads on here and was asked by a Forum Mod to make a quickie guide to be placed as a sticky on the dev boards so others might benefit.
Anyway, here is a very quick and easy way to change your ClockworkMod recovery with a couple of command lines.
The TWRP link is in the second post.
Now for the ClockworkMod Instructions:
1. First, go here and look up your ClockworkMod recovery that pertains to your phone: http://www.clockworkmod.com/rommanager
2. Download the .img file for your phone and save it on your computer.
3. Rename the .img file to recovery.img and save it to your internal sd card of your phone. For example: recovery-clockwork-6.0.1.4-hercules.img ------> recovery.img
4. Open up Terminal Emulator on your phone and type the following 2 commands:
su
dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p22
(please note the second command is a one line command with spaces between "dd & if=" and ".img & of=")
If your Rom identifies your internal sdcard as /emmc instead of /sdcard, then make the adjustment to command line (dd if=/emmc/recovery.img) instead of what is posted above.
That simple.
You can also issue these commands from adb shell if you are connected to your computer.
If Terminal Emulator does not have Superuser or SuperSU permissions for root privileges then make sure it does. You can also go from NON Touch CWM to Touch CWM using this and vice versa. Simply make sure you have the right recovery for your phone and rename it to recovery.img.
As for explanations:
dd if= command is a common Unix program whose primary purpose is the low-level copying and conversion of raw data.
dd stands for "data description"
if stands for "input file"
of stands for "output file"
the = is the location of the data you are using. ie. /sdcard/recovery.img
the /dev/block/mmcblk0p22 is the location/partition of the recovery on your phone.
So essentially you are doing a low level rewrite of the recovery image on your phone via command lines.
***Also, the best way to remember this command line is to not to. Copy the command line and save it to your own personal contact info in Google under Notes and then you will have it with you wherever you go. You really do not want to mess with getting it wrong. You could brick your phone if you mess things up.
Anyway, I hope this helps. . . . it really is very easy to execute without fault.
Works with TWRP too.
This also works with changing to and from TWRP. Download the image (for our phones it's TWRP 2.3.1.1) rename it to recovery.img and follow the above instructions and you are good to go.
Follow this link to get the image file: http://teamw.in/project/twrp2/101
***I attached the old TWRP 2.2.2.0 is case you run into problems with the newer versions not restoring backups properly or renaming backups correctly.***
Excellent Thread, I hope Dev's requiring specific CWM versions can link to your post.
Thanks for your efforts.
Noellenchris
XDA Forum MOD
Thanks for the instructions! Thanks even more for explaining the command lines.
Just thought I'd point out a small bug with the Touch Recovery. If you flash one of the newer ICS roms like Darkside Evolution through the Touch Recovery, once booted, the ROM WILL NOT SLEEP through time out. I've confirmed this with 2 separate ICS roms. Flashing non-touch recovery through Rom Manager fixes this problem.
Wouldn't it be easier to use gscript and run the commands as you need them?
Thanks for the HOW TO I actually was looking for it.
What is wrong with ROM Manager? I use it to go between Touch and normal all the time and it works flawlessly.
dextroamphetamine said:
What is wrong with ROM Manager? I use it to go between Touch and normal all the time and it works flawlessly.
Click to expand...
Click to collapse
For some people Rom Manager doesn't work. On the T-Mobile SGH-T989 Galaxy SII, Rom Manager will only allow you to go to 5.0.2.6 not 5.0.2.7. And, I think you have to upgrade Rom Manager to go to Touch. I bought Rom Manager, and don't use Touch Recovery, so I am not sure.
I like to use the command structure verses program because I know it works, it's fast, and I can see the results if an error occurs.
Oh yeah...this was really simple...Thanks...went from Touch back to Non Touch.
Give this a try
If you want a simple way to flash the Touch Recovery then give this a try. I will be adding the Hard Recovery as well in the next release.
SGSII T989 Root Toolkit
http://forum.xda-developers.com/showthread.php?t=1650908
http://forum.xda-developers.com/showthread.php?p=26200755
I get a write error: No space left on device. 1001+0 records in 1000+0 records out 512000 bytes transferred in 0.132 secs.
I reboot into recovery and it's still on 5.0.2.6
Edit: so i closed the terminal and I ran it again, and now my phone won't turn on. I get a USB device in windows called QHSUSB_DLOAD. I hold the power button, and the device disappears, but it won't turn on. I let go of the button, the same device reappears.
albanianbrotha said:
Edit: so i closed the terminal and I ran it again, and now my phone won't turn on. I get a USB device in windows called QHSUSB_DLOAD. I hold the power button, and the device disappears, but it won't turn on. I let go of the button, the same device reappears.
Click to expand...
Click to collapse
hate to be the dude that tells you this but i'm pretty sure qhsusb_dload is magic windows talk for "hard bricked phone." had that problem a while back. however all is not lost - these guys have a great reputation for Lazarus-ing dead phones.
hobakill said:
hate to be the dude that tells you this but i'm pretty sure qhsusb_dload is magic windows talk for "hard bricked phone." had that problem a while back. however all is not lost - these guys have a great reputation for Lazarus-ing dead phones.
Click to expand...
Click to collapse
Haha no worries bro. I mean worries that it failed for no reason, but I already sent it in, he just got it today. Same person you linked. Definitely trying to install ics again when i get it. Plus I think the ota ics for tmo came out yesterday or something? Probably a better experience than what was already out there with the radio and stuff.
the files from the CWM site are not .img for me, they are .ndif is it the same procedure?
MustangFTW said:
the files from the CWM site are not .img for me, they are .ndif is it the same procedure?
Click to expand...
Click to collapse
No! Do NOT use this procedure with that file extension!
What recovery are you trying to install? And for what phone? I briefly ran my cursor over the various files and the download links are either .img or .zip files. I did not see .ndif file extension.
PM me if you need additional help.
Would you happen to have the .img file for 5.0.2.7??
Edit* Nvm.. a quick google search and I was able to find it. You are a life saver.. I tried updating my recovery to the 6.0.1.2 Hercules port and for a couple days, it was working great up until an hr. ago. Nothing would flash and it would just hang in recovery... so I found this thread and thankfully I was able to downgrade back down to 5.0.2.7.
If you were local, I would take you out and get you piss drunk for helping me save my device. Cheers!!!!
fresherthanU said:
Would you happen to have the .img file for 5.0.2.7??
Edit* Nvm.. a quick google search and I was able to find it. You are a life saver.. I tried updating my recovery to the 6.0.1.2 Hercules port and for a couple days, it was working great up until an hr. ago. Nothing would flash and it would just hang in recovery... so I found this thread and thankfully I was able to downgrade back down to 5.0.2.7.
If you were local, I would take you out and get you piss drunk for helping me save my device. Cheers!!!!
Click to expand...
Click to collapse
You're welcome, I'm glad I could help you. But, the link to the .img files is in the OP instructions. . . .
Unfortunately this method did not work for me... I have tried many ways to update my CWM and none of them worked, it is almost hopeless for me
Good news! You made front page! http://www.xda-developers.com/andro...gn=Feed:+xda-developers/ShsH+(xda-developers)
Today, my phone got bricked after I installed Magisk, am i am looking for a way of sorting it out. The phone was running Android 9 DP3 when rooted, and I was following HighOnAndroids root guide on Youtube for reference,
I unlocked my bootloader and successfully installed TWRP. After this, I installed Magisk, which went throuygh perfectly fine. However, after rebooting the phone, I am stuck on the google splash screen, with a small progress bar that stays for the duration of the time on this screen. After about 2 minutes, the phone reboots into TWRP again.
Does anyone know how I could return to stock Android or at least escape this issue?
Many thanks
James
Jameswebb97 said:
Today, my phone got bricked after I installed Magisk, am i am looking for a way of sorting it out. The phone was running Android 9 DP3 when rooted, and I was following HighOnAndroids root guide on Youtube for reference,
I unlocked my bootloader and successfully installed TWRP. After this, I installed Magisk, which went throuygh perfectly fine. However, after rebooting the phone, I am stuck on the google splash screen, with a small progress bar that stays for the duration of the time on this screen. After about 2 minutes, the phone reboots into TWRP again.
Does anyone know how I could return to stock Android or at least escape this issue?
Many thanks
James
Click to expand...
Click to collapse
Use duces script to flash June google factory image.
jlokos said:
Use duces script to flash June google factory image.
Click to expand...
Click to collapse
I followed the guide on the DeucesScript XDA page but the command window keeps saying "'fastboot' is not recognized as an internal or external command, operable program or batch file."
Jameswebb97 said:
I followed the guide on the DeucesScript XDA page but the command window keeps saying "'fastboot' is not recognized as an internal or external command, operable program or batch file."
Click to expand...
Click to collapse
You need this information (the stuff I made bold + the hyperlink):
Code:
If you are having issues with this script:
Download the latest fastboot and adb Platform Tools UPDATED Dec. 22, 2017!!! This is the most common problem!!!
Download/Update Google USB Drivers
Video: Force-Installing the Android USB Drivers Fastboot & ADB
[B]Verify you have the [URL="https://wiki.lineageos.org/adb_fastboot_guide.html"]environment variable (path)[/URL] set for adb and fastboot[/B]
Try a different USB port
Try a different cable
Format Userdata in Stock Recovery
Try to boot stock before doing mods like Locking Bootloader / Kernel / TWRP / Magisk
Jameswebb97 said:
I followed the guide on the DeucesScript XDA page but the command window keeps saying "'fastboot' is not recognized as an internal or external command, operable program or batch file."
Click to expand...
Click to collapse
umph....hate to tell you, but you have a long way to go...
so before going on this "journey", I would suggest you booting into TWRP again, and try installing (not adb sideloading, just in case you're doing that) Magisk again. Also, be sure you are using the latest (might be considered "beta") 16.4 for taimen... I'm thinking your boot.img or dtbo.img simply may have gotten glitchy and repatching (by installing Magisk again) might fix it...
Also, if you want to go a step further, you might want to consider using the official Magisk uninstaller. Since Magisk makes a copy of your stock boot and dtbo image, it may put that back so you can get it in working order to get into the system (although without root), and then figure things out and/or reinstall Magisk (through TWRP is best) while all things Magisk was removed...
Good luck and hope this helps....
Make sure you are trying to open from the correct location, and put .\fastboot
EvilDobe said:
You need this information (the stuff I made bold + the hyperlink):
Code:
If you are having issues with this script:
Download the latest fastboot and adb Platform Tools UPDATED Dec. 22, 2017!!! This is the most common problem!!!
Download/Update Google USB Drivers
Video: Force-Installing the Android USB Drivers Fastboot & ADB
[B]Verify you have the [URL="https://wiki.lineageos.org/adb_fastboot_guide.html"]environment variable (path)[/URL] set for adb and fastboot[/B]
Try a different USB port
Try a different cable
Format Userdata in Stock Recovery
Try to boot stock before doing mods like Locking Bootloader / Kernel / TWRP / Magisk
Click to expand...
Click to collapse
Ive tried all of this now, i got the script working, but now the phne says it is corrupt and i cannot get into recovery. Is this game over do you think?
simplepinoi177 said:
umph....hate to tell you, but you have a long way to go...
so before going on this "journey", I would suggest you booting into TWRP again, and try installing (not adb sideloading, just in case you're doing that) Magisk again. Also, be sure you are using the latest (might be considered "beta") 16.4 for taimen... I'm thinking your boot.img or dtbo.img simply may have gotten glitchy and repatching (by installing Magisk again) might fix it...
Also, if you want to go a step further, you might want to consider using the official Magisk uninstaller. Since Magisk makes a copy of your stock boot and dtbo image, it may put that back so you can get it in working order to get into the system (although without root), and then figure things out and/or reinstall Magisk (through TWRP is best) while all things Magisk was removed...
Good luck and hope this helps....
Click to expand...
Click to collapse
This is good advice, thanks. i have a new problem (ugh), where i got the script working through changing the paths, but now the phone says that it is corrupt and i cannot access TWRP. Game over?
Jameswebb97 said:
Ive tried all of this now, i got the script working, but now the phne says it is corrupt and i cannot get into recovery. Is this game over do you think?
Click to expand...
Click to collapse
With the unlocked bootloader it'll always say the device is corrupt. Manually put the device into the bootloader & flash the DeucesScript. You're basically starting over at this point but it is possible to get up & going again.
Jameswebb97 said:
This is good advice, thanks. i have a new problem (ugh), where i got the script working through changing the paths, but now the phone says that it is corrupt and i cannot access TWRP. Game over?
Click to expand...
Click to collapse
EvilDobe said:
With the unlocked bootloader it'll always say the device is corrupt. Manually put the device into the bootloader & flash the DeucesScript. You're basically starting over at this point but it is possible to get up & going again.
Click to expand...
Click to collapse
EvilDobe might be right...but I have a bit to offer before maybe starting all over...
I doubt you needed to edit the script and "change the paths." Most likely you merely did not have the images (you extracted from the .zip of the Full Factory image you got from the Google Developers site) inside the "platform-tools" folder with the adb & fastboot .exe and all the other files and folders.
In any case, I suggest you get the TWRP image file [.img] (NOT the installer .zip necessarily), put the .img file "... inside the "platform-tools" folder with the adb & fastboot .exe and all the other files and folders." (I've seen some users simply cut and paste those 2 .exe files only to the extracted folder -- this is why I state it this way) Then, power down your device. After it's off, hold down the Volume Down button and press & hold the Power button (this is the manual way to get into the Bootloader Mode). Once there, plug your phone into your computer (USB-A to USB-C would be best) and open a command prompt/powershell ("run as administrator" or with administrative priveleges) and direct it to the platform-tools folder (i.e. if I put it on my desktop, it would be "C:\Users\MyName\Desktop\platform-tools"), you can temporarily boot into TWRP via command
Code:
fastboot boot twrp-3.2.1-2-taimen.img
When in TWRP (hopefully), I suggest trying to do what I advised before -- try either Magisk installer to repatch the boot and dtbo image, or Magisk Uninstaller to attempt to replace your boot and dtbo to stock.
*NOTE: Of course, this is assuming you are running Microsoft Windows (if not, you will need to input .\ as @naiku suggested) and also the whole "device is corrupt" is due to "funky" boot image issues. If not, I/we can guide you to flashing the Full Factory back onto the phone (hopefully without losing data and settings)...
Good luck and hope this helps...
simplepinoi177 said:
EvilDobe might be right...but I have a bit to offer before maybe starting all over...
I doubt you needed to edit the script and "change the paths." Most likely you merely did not have the images (you extracted from the .zip of the Full Factory image you got from the Google Developers site) inside the "platform-tools" folder with the adb & fastboot .exe and all the other files and folders.
In any case, I suggest you get the TWRP image file [.img] (NOT the installer .zip necessarily), put the .img file "... inside the "platform-tools" folder with the adb & fastboot .exe and all the other files and folders." (I've seen some users simply cut and paste those 2 .exe files only to the extracted folder -- this is why I state it this way) Then, power down your device. After it's off, hold down the Volume Down button and press & hold the Power button (this is the manual way to get into the Bootloader Mode). Once there, plug your phone into your computer (USB-A to USB-C would be best) and open a command prompt/powershell ("run as administrator" or with administrative priveleges) and direct it to the platform-tools folder (i.e. if I put it on my desktop, it would be "C:\Users\MyName\Desktop\platform-tools"), you can temporarily boot into TWRP via command
Code:
fastboot boot twrp-3.2.1-2-taimen.img
When in TWRP (hopefully), I suggest trying to do what I advised before -- try either Magisk installer to repatch the boot and dtbo image, or Magisk Uninstaller to attempt to replace your boot and dtbo to stock.
*NOTE: Of course, this is assuming you are running Microsoft Windows (if not, you will need to input .\ as @naiku suggested) and also the whole "device is corrupt" is due to "funky" boot image issues. If not, I/we can guide you to flashing the Full Factory back onto the phone (hopefully without losing data and settings)...
Good luck and hope this helps...
Click to expand...
Click to collapse
Pleased to be editing this comment; managed to get it working following your step by step. Think i'm going to stay away from rooting something this expensive in the future! Thanks so much!
Jameswebb97 said:
Pleased to be editing this comment; managed to get it working following your step by step. Think i'm going to stay away from rooting something this expensive in the future! Thanks so much!
Click to expand...
Click to collapse
I wouldn't go that far with staying away. When I come across people IRL that want to start doing this stuff I always tell them to read the instructions, step through them, read the instructions again, ask questions (as you did here) BEFORE you get started, read the instructions again, and only when you're confident start messing with your device. This is a fun, and at times stressful, hobby. It's great when everything goes according to plan but it's an omg omg omg omg omg omg moment when you mess something up.
Start with baby steps. The straight upgrade to P is fairly simple provided your device is unlocked. Get that working & you'll be set. I have root on my DP3 & the only thing I've done so far is delete some apps from system that I know I don't want/need. If your main goal is to just enjoy your phone, test out Android P, and maybe go back... root isn't needed. Once everything is squared away & you're running for a day or so you can always fastboot to recovery, make a backup, and then try to add root. I hope you don't shy away & get deeper into the hobby. It truly starts to get fun when you begin to understand more of what is going on.
Jameswebb97 said:
Pleased to be editing this comment; managed to get it working following your step by step. Think i'm going to stay away from rooting something this expensive in the future! Thanks so much!
Click to expand...
Click to collapse
Hey I'm so glad you got it working! Leave me a "Thanks!" would make it up to me ... I'm always happy to help out and get things figured out...yet I don't get the satisfaction of knowing if it does end up helping a lot of the time because a good number don't come back with their experience...so thanks for that! Glad you got it going...
EvilDobe said:
I wouldn't go that far with staying away. When I come across people IRL that want to start doing this stuff I always tell them to read the instructions, step through them, read the instructions again, ask questions (as you did here) BEFORE you get started, read the instructions again, and only when you're confident start messing with your device. This is a fun, and at times stressful, hobby. It's great when everything goes according to plan but it's an omg omg omg omg omg omg moment when you mess something up.
Start with baby steps. The straight upgrade to P is fairly simple provided your device is unlocked. Get that working & you'll be set. I have root on my DP3 & the only thing I've done so far is delete some apps from system that I know I don't want/need. If your main goal is to just enjoy your phone, test out Android P, and maybe go back... root isn't needed. Once everything is squared away & you're running for a day or so you can always fastboot to recovery, make a backup, and then try to add root. I hope you don't shy away & get deeper into the hobby. It truly starts to get fun when you begin to understand more of what is going on.
Click to expand...
Click to collapse
And it's as @EvilDobe means.....
I remember back in the days of the Motorola Droids (OG Droid1, Droid 3, & Droid 4) where you could really mess things up and come out with a big ol' "brick" "paperweight" as there were many instances where you could not come back from (i.e. updating to a certain point, then attempting to downgrade when Google/Motorola/Verizon put blocks that breaks it). But this isn't the case these days. @Jameswebb97, at least with the Pixel 2's, Oreo and/or P(Android OS 9), it's actually more difficult than easy to get that too far gone. The only reason why I can help so many troubleshooting their issues is because I, myself, have wrecked my current device in some serious ways! So I can relate and have experience in helping in the same situations. I've gotten it to where it says "device is corrupt," (which isn't all that uncommon), BUT with the added desperate troubleshooting where I had to wipe/erase, changing partition types, format several partitions, even go about "resizing" the partition to match the "target extraction size" of the Full Factory flash, and even as far as learning to manually flash the various system partitions and that there are two (system_a & system_b) but, in Google's infinite wisdom(?), one flashes to system_a and the other to system_other!!! And I haven't even started on reading others' issues when going after the Slot A and Slot B complications -- I didn't even attempt to touch this in that troubleshooting story.
My point is: I think I've broken my device farther than most people and got it so close to the brink, and yet I was able to bring it back and am still using that same device today (most people would usually, at that point, go and get a RMA replacement). Honestly, as long as you have access to Bootloader Mode (which Google, in their infinite wisdom, seems to have placed it in the main board memory or separate memory rather than storage as to make it always accessible which makes it hard to "lose"), you have a really good (seemingly perfect) "safety net" in which you can always flash back to a working, stock state -- which is why it's the best policy to just make good backups before experimenting so, if anything, you get back to this state and restore all your data. I'm not trying to convince you to root or to try custom ROMs or anything -- even though there are many great reasons and capabilities of rooting -- I am simply appealingl to your sense of curiosity and reassure you so you aren't held back and you don't restrict and limit yourself if you don't want to, but are to fearful to experiment.
I hope you don't take this post as "lecturing" or anything, just some thoughts I hope you consider...
Glad it worked out in the end for you!