Hoping someone had a tip to help me out. Im trying to get my radio updated so that I can properly run skyraider 3.3. I cant seem to get the radio to run in recovery when i try to book from the SD card. Am I missing something here? Any Ideas?
Is your sd card formatted FAT? The most common issue is not having your sd card formatted to FAT 32 , make sure it is for hboot to properly read it.
Is the file name proper? The zip file is case sensitive. Be sure the file name is in upper case before the dot and lower case after the dot.
Sent from my Incredible
Its properly formated as FAT. I cant seem to remember i left the name alone was this suppose to be update.zip on the root of the card? right now i have it in a sub file
The sd card should be FAT32 for hboot to properly see it, the file should be named PB31IMG.zip , and be on the root of the card.
The official radio thread;
http://forum.xda-developers.com/showthread.php?t=774155
Hope this helps.
Sent from my Incredible
Im pretty sure the SD card is formated correctly because its worked on all other flashes. Its still not taking the new radio even after showing its loading. It is formated as FAT 32. I have tried both the newest radios. When reading from Hboot it flashes bad image several times and then finally says checking the image and then nothing. Any other suggestions..... anyone?
Just to clarify Im trying to get skyraider 3.3.3 working (keeps rebooting on me after flashing it) someone said i needed to upgrade from the 2.05 radio. I have wiped. When it boots up to the setup screen it tells me that ROM manager has to be forced closed and then about 15 sec later it freezes and reboots.
I cant seem to get the radio to run in recovery when i try to book from the SD card.
Click to expand...
Click to collapse
You flash radios in BOOTLOADER not RECOVERY.
SynbiosVyse said:
You flash radios in BOOTLOADER not RECOVERY.
Click to expand...
Click to collapse
Im sorry I miss spoke I have been in bootloader. Any suggestions?
Kipphh said:
Im sorry I miss spoke I have been in bootloader. Any suggestions?
Click to expand...
Click to collapse
If you are 100% sure that you are formatted in FAT32 and have the file name correct then you possibly have the same problem i did which was my stock SD card went bad and I had to get another.
I have a mytouch slide and im stuck on....
(htt p://theunlockr.co m/2010/08/16/how-to-root-the-htc-mytouch-slide-exploid-method/) 8:50 It says ESPRIMG not found?
I also tried this....
(htt p://w ww.youtube .c om/watch?v=sVjoKvy-YZg) 3:30
I have unpluged it many times and on my comp it is not on recovery???
please help thank you
(links are with out spaces sorry im a new user and the time on the side of the link is where in the part in the video is located and i feel ive done everything correct)
This is tearing me apart!!!!
ESPRIMG not found error is usually fixed by reformatting your SD card, taking care to use the FAT32 format (not just FAT). Format your card and put everything you need back on it and try again...
HTH,
JTB
JTownBrewer said:
ESPRIMG not found error is usually fixed by reformatting your SD card, taking care to use the FAT32 format (not just FAT). Format your card and put everything you need back on it and try again...
HTH,
JTB
Click to expand...
Click to collapse
Im a noob how do i do that.
I can't remember if it works to format the card with it in your phone or if you need to take the card out and plug it into your computer through a card reader .. think it works through the phone.
So plug your phone into you computer and make sure that the sd card contents are available through the computer (you might have to turn on the disk drive setting on your phone).
In Windows you would then right click on the drive for your phone's SD card and select format. Then make sure the format is set to FAT32.
JTB
Ok I've rooted every thing but I got a few problems
I get no cell phone service
And I want the slide rom not the nexus one and all I rooted for was to get the froyo ota for the slide that went unrealsed so if you can help I greatly love it thank you
heres the guide i used....
http://forum.xda-developers.com/wiki/index.php?title=File:HTC_Espresso.png
this is what i want....
http://forum.xda-developers.com/showthread.php?t=928250
If all you want is the official Froyo update then you can now go download it directly from HTC. See the Offical Froyo is out on HTC site! thread.
Note that following that path will remove root from your phone.
If you would rather keep root you have a few other options. There are a few sense rom variants including the one you linked to.
If you already have root and have installed rom manager then you shouldn't have any trouble using that to install a new rom, create backups, etc.
Not sure what your comment about nexus 1 meant? You certainly cannot install a nexus rom on the slide. Did you mean the Cyanogenmod ROMs?
JTB
My nephew tried to root his A100 and somehow ending up where now all he gets is the "recovery verified failed-spin forever" message. I have done some research on this forum and others and I am seeing some updates and such to put on the SD card to try and reboot the tablet to its factory settings. My problem is this-how do I access the SD card if the tablet won't boot? When I connect the USB to my laptop it doesnt recognize the mount(or whatever you call it) so I am unable to read or transfer files to the SD card.
I am using a blank SD card since he didnt have an external card of his own. So I guess my question is this-is there any way to read the SD card via USB that I am missing, or do I have to place the files from my laptop to the SD card directly, and then replace the SD card in his tablet(I hope this all makes sense!) Also, when it says to put the update.zip on the SD card, it is the whole zip file or the folder within?
Thanks so much for your patience. Im trying to save my nephews rear end because his mom is pretty mad he screwed up a new tablet that she spent good money for.
Tim S. said:
My nephew tried to root his A100 and somehow ending up where now all he gets is the "recovery verified failed-spin forever" message. I have done some research on this forum and others and I am seeing some updates and such to put on the SD card to try and reboot the tablet to its factory settings. My problem is this-how do I access the SD card if the tablet won't boot? When I connect the USB to my laptop it doesnt recognize the mount(or whatever you call it) so I am unable to read or transfer files to the SD card.
I am using a blank SD card since he didnt have an external card of his own. So I guess my question is this-is there any way to read the SD card via USB that I am missing, or do I have to place the files from my laptop to the SD card directly, and then replace the SD card in his tablet(I hope this all makes sense!) Also, when it says to put the update.zip on the SD card, it is the whole zip file or the folder within?
Thanks so much for your patience. Im trying to save my nephews rear end because his mom is pretty mad he screwed up a new tablet that she spent good money for.
Click to expand...
Click to collapse
Was he running ICS or HC? Is he able to boot into recovery (most likely not, but that is needed to flash the ICS update)? See if he can remember what he did. You could place the sd card in a card reader and send the file directly to it. Yes, you place the entire zip file on the sd card (do not extract it).
Ask him which thread/method he tried to use. That should help figure out wat he was messing around with in the first place
Sent from my A100 using tapatalk
Ok thank you guys very much. I will call him tomorrow and find out what he did(or tried to do). Appreciate your help.
Ok...so he's not sure exactly what he did because he is saying his friend did it haha. I asked him to call his friend, but the friend was a kid he met at the skatepark and he doesnt know where he lives...hmmm... anyhoo, where does that leave me?
I put the zip file on my SD card from my phone and put it into the tablet, did the power on/volume up trick and got the same "spin forever" message. If anyone can walk me through another process I am open to putting in the time.
My next move(or last one) would be to call Acer and plead my nephew's case and hope they would honor the warranty(but then I would have to lend my nephew the money to ship the tablet back and forth haha because his mom won't pay for it!)
Again, thank you so much.
Tim S. said:
Ok...so he's not sure exactly what he did because he is saying his friend did it haha. I asked him to call his friend, but the friend was a kid he met at the skatepark and he doesnt know where he lives...hmmm... anyhoo, where does that leave me?
I put the zip file on my SD card from my phone and put it into the tablet, did the power on/volume up trick and got the same "spin forever" message. If anyone can walk me through another process I am open to putting in the time.
My next move(or last one) would be to call Acer and plead my nephew's case and hope they would honor the warranty(but then I would have to lend my nephew the money to ship the tablet back and forth haha because his mom won't pay for it!)
Again, thank you so much.
Click to expand...
Click to collapse
Did you try resetting it? This may be quite crazy but, you could try unlocking the bootloader, flashing a recovery, then flashing a rom.
Sometimes people rename the file and add an extra "zip" and that gives the error you describe. Take the file onto your computer (I am using Windows, and do not know Linux) right click and rename the file "update". Do not add zip.
Try that.
or they tried the acer recovery app from the market and borked the stock recovery. if thats the case youll have to find the thread crossix has the original files on and follow his instructions.
Sent from my A500 using xda premium
ptesmoke said:
or they tried the acer recovery app from the market and borked the stock recovery. if thats the case youll have to find the thread crossix has the original files on and follow his instructions.
Sent from my A500 using xda premium
Click to expand...
Click to collapse
That could be the issue, but the method crossix gave to fix it requires it to be done through the terminal (so the device needs to be booted up for it to be done).
The zip file is named correctly(not with an additional .zip)..When you say to flash, I'm not sure what that means. Does that mean putting the files on the SD card through my computer? Also, yes, I did try resetting it and same result. I have submitted a service ticket to Acer waiting to hear back. Thanks for all your input, sorry to be such a noob..
Tim S. said:
The zip file is named correctly(not with an additional .zip)..When you say to flash, I'm not sure what that means. Does that mean putting the files on the SD card through my computer? Sorry to be such a noob..
Click to expand...
Click to collapse
No. To flash the file, you just need to place it on your external sd card, then boot into recovery (it seems like your's is corrupted though).
I ended up sending the Tablet in for service. Fingers crossed that will fix it free of charge under the warranty! Thanks again for everyone's help!
So I never got the 4.3 OTA BUT I did install the UCUEMJB Bootloader, but not the modem to use the 4.3 Dandroid Rom, about all month before that I was happily on CM11, and loved it. I try Dandroid because I hate Touchwiz so much, but thought this might cure my want to switch ROMs all the time.
I tried to port the Moto X 4.2.2 Rom, and decided to flash it. The phone came on once with the Samsung logo, Went off, and usually it would vibrate and vibrate meaning something is wrong, this time it just went off and didn't vibrate at all.
It is hard bricked from my understanding, but I have no way of getting a JTAG Done, and I'm waiting on a JIG I ordered, but this is becoming too long without a phone. I bought 3 100K Ohm resistors, and tried the method here: http://forum.xda-developers.com/showthread.php?t=889128 and I can't seem to get it to work.
I tried the USB Debrick img for the JB Bootloader, but that didn't work neither. The battery is good, and works and everything, Just trying to rule out everything so many you can help me a little better.
Does anyone have any idea what to do? I can't afford a Riff box neither.. if I can get it fixed I'll just stick with one Rom this time, lol.
is there any way to JTAG without the Riff Box, or anything I can do? I'm willing to try anything at my power.
Thanks in Advance.
lemonboi5 said:
So I never got the 4.3 OTA BUT I did install the UCUEMJB Bootloader, but not the modem to use the 4.3 Dandroid Rom, about all month before that I was happily on CM11, and loved it. I try Dandroid because I hate Touchwiz so much, but thought this might cure my want to switch ROMs all the time.
Click to expand...
Click to collapse
You should try http://forum.xda-developers.com/showthread.php?t=2549068 you were on 4.3 these files are for 4.3
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
theramsey3 said:
You should try http://forum.xda-developers.com/showthread.php?t=2549068 you were on 4.3 these files are for 4.3
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Thanks for the reply!
I have been looking at that all morning, so even if I flashed the Moto X Rom that was ported, I shouldn't need JTAG?
Also, let me get this straight.. I use WinDiskImager to put the img file on the SD card, via my SD card reader, and then Pull the battery, put in the SD card, put in the battery, and turn on the phone? because I've tried that and it doesn't work at all for me.. unless I'm missing something here, I'd love to know!
You are using a 16GB or larger card right?
You aren't trying to get the phone to power on just yet. Only trying to get to recovery mode so you can flash stock 4.3 stuff and get going again.
With that said...
It appears it is only about 70 percent successful. I have had reports from folks that said they had to write the .Img file several times in a row in their SD card slot in the computer to get it to work.
You may have to get a debrick file from someone running the same rom you were trying to flash.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
When you plug your phone into your PC, do you get a box that pops up and reads something like "can't load drivers QHSUSB DLOAD"?? If so, this is what I did. I followed the instructions in this thread:
http://forum.xda-developers.com/showthread.php?t=2581166
I used the AT&T image from this thread (I was on Paranoid Android 4.3, FYI):
http://forum.xda-developers.com/showthread.php?t=2345860
Worked just fine.
Now, the link in the post above me mentions Odin'ing back to 4.1 so you don't have to boot from your SD card anymore. I didn't do that. When mine booted, it booted into Recovery and I flashed my Paranoid Android 4.3 ROM and GApps. That worked fine and all my data was intact, but yeah, it meant That I'd have to boot from SD card every time. To get past that, I plugged my phone in, copied the AT&T .img file from my PC (note, I copied...I didn't image it. When you image it, it pulls files from the .img file and writes a partition containing them. You don't want to do that in this case) to a random internal SD card file folder on my phone. I had to do it that way cause that AT&T .img was too big to fit on my SD card imaged with the debrick boot files. I then I opened my file manager app on my phone and moved the .img file to the /SDCARD folder. From there I used the terminal emulator and followed the instructions from the link I posted first, typing
su
dd if=/sdcard/debrick.img of=/dev/block/mmcblk0
Took my SD card out. Restarted. It booted into recovery again, I flashed my PA 4.3 ROM and at that point I was able to boot without the SD card and didn't have to Odin back to an older version. Finally, I used the SD formatter here:
https://www.sdcard.org/downloads/formatter_4/
And formatted my SD card back to allow full usage. Copied all my old files and pics back on it and I was straight!
theramsey3 said:
You are using a 16GB or larger card right?
You aren't trying to get the phone to power on just yet. Only trying to get to recovery mode so you can flash stock 4.3 stuff and get going again.
With that said...
It appears it is only about 70 percent successful. I have had reports from folks that said they had to write the .Img file several times in a row in their SD card slot in the computer to get it to work.
You may have to get a debrick file from someone running the same rom you were trying to flash.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Its an 8GB Sandisk D: Is there a difference in the way it performs? I'm flat broke atm, but if someone can point me in direction of a cheap 16GB or bigger card, I'll go after it for sure.
Charles: said:
When you plug your phone into your PC, do you get a box that pops up and reads something like "can't load drivers QHSUSB DLOAD"?? If so, this is what I did. I followed the instructions in this thread:
http://forum.xda-developers.com/showthread.php?t=2581166
I used the AT&T image from this thread (I was on Paranoid Android 4.3, FYI):
http://forum.xda-developers.com/showthread.php?t=2345860
Worked just fine.
Now, the link in the post above me mentions Odin'ing back to 4.1 so you don't have to boot from your SD card anymore. I didn't do that. When mine booted, it booted into Recovery and I flashed my Paranoid Android 4.3 ROM and GApps. That worked fine and all my data was intact, but yeah, it meant That I'd have to boot from SD card every time. To get past that, I plugged my phone in, copied the AT&T .img file from my PC (note, I copied...I didn't image it. When you image it, it pulls files from the .img file and writes a partition containing them. You don't want to do that in this case) to a random internal SD card file folder on my phone. I had to do it that way cause that AT&T .img was too big to fit on my SD card imaged with the debrick boot files. I then I opened my file manager app on my phone and moved the .img file to the /SDCARD folder. From there I used the terminal emulator and followed the instructions from the link I posted first, typing
su
dd if=/sdcard/debrick.img of=/dev/block/mmcblk0
Took my SD card out. Restarted. It booted into recovery again, I flashed my PA 4.3 ROM and at that point I was able to boot without the SD card and didn't have to Odin back to an older version. Finally, I used the SD formatter here:
https://www.sdcard.org/downloads/formatter_4/
And formatted my SD card back to allow full usage. Copied all my old files and pics back on it and I was straight!
Click to expand...
Click to collapse
is your SD card bigger than 8GB? That's what I have, and I'll try all of this and report back
My phone doesn't turn on at all, So You mean to copy the IMG file to the SD Card? or the files from the IMG File to the SD card? I am not able to get into any file managers and ADB can't read my phone at all :/
First off, you need a card larger than 8gb. It has to be at least 16gb. Mine was 32gb.
Second, to get it to turn on at all, you need to use the disk imager listed in the thread I posted. WinDiskManager or whatever it's called. Grab the AT&T .img file from the second link (that's the one that worked for me...not sure it will for you) and save it somewhere on your PC. Open the disk imager and choose the AT&T .img file, then use the drop down and select your SD card (whatever letter your PC assigned it) and finally, click "write". That will image the files contained in the .img file to your SD card and partition it as bootable. Put the SD card in your phone, turn it on, and it should turn on to recovery at least. Once we get there, we can tackle moving the .img file to where it needs to be on your phone so you don't have to boot from the SD card anymore.
Yes exactly it is mandatory that your card MUST be 16 gb or bigger. What we are doing is mimicking the internal storage on the phone and tricking the phone into booting into recovery to fix what we messed up. Walmart has fairly cheap SD cards. They're cheaper than $50 to get a jtag and faster too.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Oh okay I get it now. Thanks for the explanation. I'll be on the look out for a 16GB.
Oh okay I get it now. Thanks for the explanation. I'll be on the look out for a 16GB. I found some cheap on Ebay for $10 when I get paid I'll get one! (Living check to check... lol) I also went ahead and bought a jig for $1.89, I'm asking around if any of my friends have an extra 16GB SD, most likely not though. Thanks for the replies!
BTW, My phone is like. Dead. Doesnt even power on or anything, but I do get the QHSUSB DLOAD thing, and if I plug it in without a battery I get a Red LED indicator, is that how you guys have explained previous phone states?
I never had it plugged in without the battery, but yes, when I plugged it into my PC, I got what you're getting. We should be able to get you back in business. Hurry up and get an SD card. Hell, go buy one, use it, then return it.
Charles: said:
I never had it plugged in without the battery, but yes, when I plugged it into my PC, I got what you're getting. We should be able to get you back in business. Hurry up and get an SD card. Hell, go buy one, use it, then return it.
Click to expand...
Click to collapse
Holy crap sir, I like the way you think.
Edit:
So I was able to get my sister to loan me the money to get one and return it lol.
So now I flash it with the AT&T Debrick Img...
pull the battery, insert SD, insert battery, try to turn it on?
Or am I missing something? lol
Going to pick it up now, just wanted to retrieve the "What now" steps ahead of time! Thanks everyone!
Charles: said:
I never had it plugged in without the battery, but yes, when I plugged it into my PC, I got what you're getting. We should be able to get you back in business. Hurry up and get an SD card. Hell, go buy one, use it, then return it.
Click to expand...
Click to collapse
I got an SD card, I tried the img's and it still wont turn on D:
Its a Class 10 Samsung 16GB Micro SD card, Currently keep trying to write the Debrick-SGH-i747U-CUEMJB3.img, and trying it out, still not working. Is that the OTA Bootloader? JB3? Or just JB? Or maybe its the J2 Bootloader I have with a JB3 Modem... forgive me lol.
Dead phone still.. I think I wanna cry lol
Edit:
In addition this is what I'm getting..
qualcomm hs-usb qdloader 9008 (COM4)
No idea what that means, but it shows up in Device Manager.
I've been trying and trying to flash this img and get it to come on, still not working
Did you image the SD card with this program?:
http://sourceforge.net/projects/win32diskimager/
After you image it, check your SD card in Windows Explorer and verify there are files on it. There should be quite a few.
If you did and the image you tried to flash didn't work, did you try the AT&T image that I linked to in my first post? This one?
http://d-h.st/iEy
Charles: said:
Did you image the SD card with this program?:
http://sourceforge.net/projects/win32diskimager/
After you image it, check your SD card in Windows Explorer and verify there are files on it. There should be quite a few.
If you did and the image you tried to flash didn't work, did you try the AT&T image that I linked to in my first post? This one?
http://d-h.st/iEy
Click to expand...
Click to collapse
The files are on the SD card in a folder called "image".. that doesn't sound good. I browsed for the .img and wrote it to the sd and everything D: I've done this a lot, any idea?
lemonboi5 said:
The files are on the SD card in a folder called "image".. that doesn't sound good. I browsed for the .img and wrote it to the sd and everything D: I've done this a lot, any idea?
Click to expand...
Click to collapse
Yes...that's correct. My SD card had numerous files in a folder named "Image", so it seems you're doing that portion correctly.
Did you try the AT&T image that I linked to? That one was named different from the one you referred to in your previous post.
Just to cover your bases, try both AT&T images that were linked to in this thread. If it's still not working...don't know what to tell you.
Charles: said:
Yes...that's correct. My SD card had numerous files in a folder named "Image", so it seems you're doing that portion correctly.
Did you try the AT&T image that I linked to? That one was named different from the one you referred to in your previous post.
Just to cover your bases, try both AT&T images that were linked to in this thread. If it's still not working...don't know what to tell you.
Click to expand...
Click to collapse
Yes, I've tried that one, and the one that theramseys uploaded, I just don't know if I'm doing something wrong here.
I stick in the sd card, and try to turn it on? it doesn't power on still.
So stuck here I've done the 3 button combo, and everything. it just wont turn on :/ Any more ideas? Should I just try it with linux? but then again how bad can Windiskimgr actually be?
I miss my phone so much! lol
I dunno, man. I flashed the image I posted, put the SD card in and it turned on. Just pressed the power button.
Charles: said:
I dunno, man. I flashed the image I posted, put the SD card in and it turned on. Just pressed the power button.
Click to expand...
Click to collapse
No tricks to it? I even tried using dd in linux, still nothing. If all fails I hope the jig works that I ordered. I was porting that Moto X rom from a Cyanogenmod 10.1.3 Base, but had swapped out mostly permissions and framework, I didn't touch the boot.img or anything like that.. I did kind of touch up on the updater-script, but still I don't see how that'd brick it, usually it'd give me a status7 or something if it didnt work, or even vibrate, turn on, then vibrate twice and restart, till I'd put it back into recovery, but with that 4.3 Rom I was throwing root issues, and every time I re-flashed it, I had to re isntall CWM
Yeah, just uncovered a new chapter of the story.. lol Hopefully we can work with this at all.
I tried to downgrade to a 4.2.2 Version from 4.3, and had a 4.3 Bootloader,
before all of this I was happily on the CM11 Rom, and should have stuck with it.. Curiosity killed the kitkat.