(S)Solving the Zune connection error - Windows Phone 7 Development and Hacking

Solution about that wp7 device like HTC HD7 connected to the computer cannot be identified.
This solution only applies to that relocked/locked HD7`s USB Mode Status is Diag Mode and cannot be identified.The Zune had no way to synchronize HD7.Some drivers problem can refer to the website http://support.microsoft.com/kb/944909/zh-cn
My solution is limited only to the following:
1.HD7 installed USBModeSwitch.xap in the unlock state and change USB Mode Status from normal Zune Mode to Diag Mode with the UMS tool.After that,then in the absence of the usb mode status back to the case of zune mode,it was uninstalled by some reason,and lost the unlock permissions.
2.Other relevant conditions not mentioned above.
The whole drivers installed in all the circumstances,at this time HD7 connected to the computer via usb cable,but zune software did not recognize and synchronize HD7.Look in device manager is displayed as "unknown device" with two yellow failed to identify the device.
This moment hd7 state in the tri-color screen (vol- button and power button),state in the usb mode (vol- button,photography button and power button),PC equipment can identify HD7.And it can reflash official verdor rom.
I tried contacting some gay from xda forum and try to resolve this USB error.
1.My phone is u.s. Tmobile HD7,spl state not unlocked ,no security unlock words exist.
2.The USB error exists in the spl underlying,system reset and flash series offical vendor rom can not make the situation better.
3.Solution to ,way through the Y-cable and goldcard to flash another vendor series offical rom,or spl unlock to get SuperCID to flash the rom.
Tips,
1.The way through the Y-cable and goldcard to flash another vendor series offical rom can be found in xda forum.
2.Now HD7 spl lock can be unlock via Y-cable + goldcard + whitecard.Through that SuperCID permission can be obtain so that I can flash any rom I want.

mzdairy said:
Solution about that wp7 device like HTC HD7 connected to the computer cannot be identified.
This solution only applies to that relocked/locked HD7`s USB Mode Status is Diag Mode and cannot be identified.The Zune had no way to synchronize HD7.Some drivers problem can refer to the website http://support.microsoft.com/kb/944909/zh-cn
My solution is limited only to the following:
1.HD7 installed USBModeSwitch.xap in the unlock state and change USB Mode Status from normal Zune Mode to Diag Mode with the UMS tool.After that,then in the absence of the usb mode status back to the case of zune mode,it was uninstalled by some reason,and lost the unlock permissions.
2.Other relevant conditions not mentioned above.
The whole drivers installed in all the circumstances,at this time HD7 connected to the computer via usb cable,but zune software did not recognize and synchronize HD7.Look in device manager is displayed as "unknown device" with two yellow failed to identify the device.
This moment hd7 state in the tri-color screen (vol- button and power button),state in the usb mode (vol- button,photography button and power button),PC equipment can identify HD7.And it can reflash official verdor rom.
I tried contacting some gay from xda forum and try to resolve this USB error.
1.My phone is u.s. Tmobile HD7,spl state not unlocked ,no security unlock words exist.
2.The USB error exists in the spl underlying,system reset and flash series offical vendor rom can not make the situation better.
3.Solution to ,way through the Y-cable and goldcard to flash another vendor series offical rom,or spl unlock to get SuperCID to flash the rom.
Tips,
1.The way through the Y-cable and goldcard to flash another vendor series offical rom can be found in xda forum.
2.Now HD7 spl lock can be unlock via Y-cable + goldcard + whitecard.Through that SuperCID permission can be obtain so that I can flash any rom I want.
Click to expand...
Click to collapse
For Chinese it can be refered to the website below
http://www.qdppc.com/thread-45087-1-1.html

Whitecard,in China we named it like that,is a white SIM card which is widely used in industrial production and testing process communication.After using this SIM card to unlock the phone system boot mode will be changed,when the phone is switch on when the loading system engineering test unit will be loaded into the startup intend.

Hi,
i have the problem as described above (Unknown Device error)
But i don't understand how i can solve it....
PLEASE can you give me information what i need, and what i have to do exactly...
i'm desperate
Thank you....

Read my post content carefully.

So my understanding is this:
1: You boot the phone while holding down the -ve volume button
2: Connect the phone to the computer when the three different colour bands are showing
3: Wait until windows detects all the necessary drivers. BTW my computer detected it as a Qualcomm CDMA device. Is this normal?
4: Now this is where I got lost. You flash it with a ROM from a DIFFERENT telecom?
5: Once it has been flashed you do something with a Y-cable, a whitecard (a blank SIM card I think) and a goldcard (don't have a clue what this is)
6: Now superCID (something I once again don't have a clue about) does something so you can flash any ROM you want.
I don't see how this solves the issue of returning the phone to Zune mode but maybe someone else can make sense of it.
I, and many others, would greatly appreciate the help.
Thank you.

Related

mda exac in serial mode help !!!

sombody messed it up with jafwm, now is dead when i go to bootloader mode
its only serial mode when i connect usb cable windows says unrecognized device and before was ok even when was not powering on windows recognize device. Then i try to flash it again with jafwm and first part of rom was erased but nothing was writen to phone (writting error).
My question is : - is there any possibility to flash it from memory card or by serial cable, or how to fix bootloader ???
br
Try asking Raskal directly or posting here:
http://forums.phone-tools.cn/forumdisplay.php?f=170
Richard
alredy done that couple weeks ago and no reply thats way i am looking for another way to fix it

USB Device Not Recognised on Bootloader

I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device

I'm in bootloader screen beacause the notebook power off

Hi,
I've tried to upgrading with 9000_WWE_20202_20307_11500.exe found in this forum, but the notebook power off (bad economic mode also with the AC plugged) at the ExtRam update on 1%, just after the Radio.
But when I tried to re-run the program nothing change, just the bootloader v1.01.
Now the program recognize that there are nothing installed and ask to install all new Roms but after the second screen the utility tell me everytime: "ERROR 114 RADIO ROM UPDATE ERROR"
Somebody can help me?
Since the OS ROM is updated in the last step(to be precise, Step 3), you can easily take your device out of this bootloader mode.
1)open MS activesync on your desktop
2)go to connection settings and disable 'incoming USB connections"
3)run the exe(see the attachment)
your device should be out of bootloader mode.
PS: you can re-run the ROM upgrade again after your device gets back to life
Now my Universal is completly OFF
Hi, thanks a lot for your attention, I trye to follow your instructions but now after the Exit of bootloader, I can't update my Universal.
After read dozens of messages... I try to explain better my situation:
1) the first update was blocked by the power off in my notebook in the beginning on the ExtendedRam (1%)
2) after this I tryed to re-run the update program and this recognize NO ROM on my UNiversal and asking for replace with all new ROM, but a "error 114: Radio Rom update" don't let make the update. (that repeated many time and every time I tryed to reset, cold reset, warm reset... following all the messages that explained many different way to de-block the situation)
3) Now the screen is absolutly black and the PC say me taht the "USB Device Not Recognized"
Can you help-me?
Thanks for all...
I've search and now I've found the way
Thanks for your help, I have come back at bootloader mode and I can put in the wm6 version !
Bye
hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...
seranares said:
hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...
Click to expand...
Click to collapse
It's ok, after a reboot of my pda & PC, I can exit the bootloader.
Thks for this program

no usb connection

my diamond stucks in the bootlaoder when i put into the pc i don't get usb, the pc says qualcomm cdma technologies msm searh driver but i dont have it please help
Sounds like you need to flash from your phone as per instructions from other thread:
First make sure you flash Hard SPL then
Extract the RUU_Diamond_HTC_Europe_2.03.401.2_Radio_Signed_Dia mond_52.51.25.26_1.09.25.23_Ship.exe file (or whatever one you are wanting to flash) to a new directory on your PC
Find the RUU_signed.nbh file in this new directory and rename it to Diamimg.nbh
Copy Diamimg.nbh to the root of Internal Storage
Hold in the volume down button + the back button (thats the top right button on the front to the right of the big middle jog control) + soft reset
Follow instructions on screen
When the process is complete (it will say UPDATE SUCCESS) then reset
If it says rom image not found then you may need to follow the thread about stuck at 0-5% and use NBH util to mod the image to change the model ID
ketie007 said:
my diamond stucks in the bootlaoder when i put into the pc i don't get usb, the pc says qualcomm cdma technologies msm searh driver but i dont have it please help
Click to expand...
Click to collapse
Hi
It is look like you are trying to flash a GSM rom to a CDMA diamond. you should read the CDMA section about your problem. Do not try any GSM roms on the CDMA device, as far as i know GSM rom won't work.
Good luck
the phone just crashed, i didn't wont to update my ram, wen i want to hard spl i dont find a phone
when i hard reset the phone says
trigger usb host....
retry enter usb....
don't find a map in explorer to
what can i do is the phone for the bin
help me please
Your device in bootloader state. Can you see the connection changes from serial to usb? If confirmed so you have a good chance to go further!
Do you have a appropriate active sync driver on your computer? Did it work before? If confirmed you should activate - Connection Settings - so the PC can detect your HTC device by usb
You know the rest of the procedure!
Deleted post
i dont see any progress, i sopose i've dont have the driver,
the bootloader stays on serial and the active sync didn't find the connection
ketie007 said:
i dont see any progress, i sopose i've dont have the driver,
the bootloader stays on serial and the active sync didn't find the connection
Click to expand...
Click to collapse
Hi
Disconnect phone from usb then reconnect to usb.
In pc install activesync driver which will be found by pc itself.
If this is not successfull left diamond connected and restart the pc it will automatically install activesync driver.
then flash a rom from pc.
Good luck

Unknown USB device (failed request for device descriptor)

I have a problem.
My screen is broken. Now I want to send him to OnePlus.
But before that I want unroot it. Or at least reset to factory defaults. But both things fails.
I have the latest FreedomOS Rom. Since then I can no longer use TWRP. When I start my phone to the recovery the screen goes black and nothing happens anymore.
The same happens when I put it back to factory settings through the settings menu .
I've read there is a modified version of TWRP.
From here begins the real problem. Windows doesn't recognizes my phone.
In Device Manager it appear as "unknown USB device (failed request for device descriptor)"
What I've tried:
Boot in to Bootloader
Original (Dash) USB cable
Other USB cable
WIndows 10
Windows 7
USB debugging on
USB debugging off
OEM unlocking on
OEM unlocking off
USB configuration: File transfer
USB configuration: MTP
USB Configuration: Charge
Anyone have an idea?
Maybe it's the ROM. But I cannot flash another ROM because I can not get into TWRP.
Maybe it's an option to flash the modified TWRP without a computer. So right from the bootloader. But I do not know if this is possible. And how it should be done.
You're in wrong device forum. This is specific for One M8 not OnePlus.
For One M8, most of the time HTC USB drivers will fix that unknown USB device problem.
Maybe something like that for OnePlus, so ask in your device specific forum.
Och, I'm sorry. Please close this topic for me. I'll make a new one in the right place.

Categories

Resources