Related
Folks:
My PDA2k stylus has become too loose and I am starting to drop it everywhere: my pockets, my car, etc. In all likelihood, if I don't find a solution pronto, I'll be using my fingers because of a lost stylus.
Is anyone out there having this problem? How do you deal with it?
Thanks in advance.
Fernando
my XDA2s is getting worse, its 2 months old and gets used, give it another month and i be needing to get a big big box of replacement stylus's
Stylus problem? no problem.
Hey guys!
I'd just leave the regular stylus in my MDAIII and I went and got these check it out : http://www.truetip.com
They have all kind of stylus stuff that may can work out for you. I bought a few :wink: of each and I hardly every use the one in my unit. I hope this helps, Take care fellas! :wink:
I've just encountered this problem and went the "Classy" way with my solution.
Magic tape wraped twice around the top of the stylus. Fingers crossed I'll have no more retracing my steps fun looking for a missing stylus. :lol:
hmmmn just put (stick) small neoprene inside the hole (opening)....
[5561 004.jpg]
[5561 006.jpg]
thanks,
jojo
Or just buy some more styluses i bought 3 from here and recieved the item next day. I'm also going to buy an xda2s handsfree from him as i have lost that 2.
http://search.ebay.co.uk/_W0QQsassZairportinfo
expansys.com has a lot of different kinds of stylus for PDA2K or similar. there are regular and with pen included.
expansys has offices in diferents countries. check yours.
Tano
Leave it in for service, it's the only way that HTC will understand that they need to go up some notches on the Hardware quality.
There is no way I'm taping anything on a 1.000,-$ unit
Mine is headding for service once more in the near future.
tano said:
expansys.com has a lot of different kinds of stylus for PDA2K or similar. there are regular and with pen included.
expansys has offices in diferents countries. check yours.
Tano
Click to expand...
Click to collapse
these ones are original styluses
http://search.ebay.co.uk/_W0QQsassZairportinfo
There is no way I'm taping anything on a 1.000,-$ unit
Click to expand...
Click to collapse
Good point. This thing cost more than my old car. Just whilt we're on the topic of hardware that was clearly not tested thoroughly before it as marketed, does anyone else's sliding mechanism scratch the keyboard?
yep on the left hand side. and i hardly ever use the keyboard so its not down to wear and tear.
to be honest the xda2s does feel cheap when its on your hand.
scratch on the left side of keyboard... hardly used the keyboard though...
and a gap between the lcd and battery slider on the right hand side...
I fixed mine with a single layer of tape around the top of the stylus. Now just enough grip to hold on.
rich
Mine went back to the O2 service centre on Sunday! The slider was never right from the day I got it (this one was my second) and I lost a stylus the other day. The sliding keyboard was so far away from the chassis I could see daylight through it!
I also had the "wear" makes on BOTH sides of the keyboard and the Sales assistant said that they ALWAYS get those on every unit they get back, which I'm told is quite a few!
I'm waiting on a response from them as I suspect as before, they will just give me a brand new one. Anyway, I'm thinking of Ebaying the XDAIIs and getting myself an Orange c550/Qtek 8200 (HTC Robbie) Smartphone as I'm not impressed with the build quality compared to the XDAII/IIi!
We'll see!
Dom
Loose stylus - Stylus falls out
I dropped my BA 5 meters onto a concrete floor. It landed on the corner and bent the corner in. I just picked it up and it still worked. I use it in a industrial enviroment so it looks ugly, but always works. My old Ipaqs couldn't handle a one meter fall onto carpet without cracking the screen.
Oh yeah! Here's the fix to the original problem on this thread. It's really a easy fix. It's been 5 months since I lost a stylus.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-If your corner is bent straighten it now(see above)
-Reassemble BA
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade!
Good Luck,
N2O2
The Low-Tech Way
I crammed a little wad of paper into the area between the case and the little plastic spring. Works like a charm!
Hi guys, just wondering if any users out there are having the same problems as me. ive had my Blue Angel now for a good 6 months and im very happy with it appart from it doesnt ring which is very very annoying :twisted: anyone know a fix for this?
But main reason for this post is; has anyone got the same problem that the holder for the stylus has become used and now doesnt hold the stylus in place anymore? i remember there being a click when pushing the stylus in. but now it just falls out when i tip the PDA upside down.
Anyone whos opened up a BA can you give any details on how the holder works? can it be modded so that it grips the stylus again? im one for opening up electrinics and playing with them but since i use this for alot of my work i cant risk it.
many thanks for any replies.
DJUPLIFT
I have the same issues. I tried to take mine apart but could not seem to separate the back side of the case. I removed 3 screws from behind the battery, and one from either side of the device. I too would like any input.
It totally blows... cos i always end up taking the phone out of my pocket and sometimes i dont hear the stylus drop. ive already lost two like this... it might end up being more expensive to just keep buying stylus than to open the BA and screw it up... All in all my ones been opened already :shock:
i dropped it on concrete and somehow the touchscreen stopped working although the screen was intact. O2 replaced it with a brand new one for diddly sqwat!! FANTASTIC!!!
i might just take it appart next weekend and have a little look inside see if there is a way to access this comparment and maybe doing a little DIY style modding!
if i come up with any conclusions ill post them with some pics of course!
DJUPLIFT
a friend of mine took his apart and there does not appear to be a way to tighten the stylus. He said it was just a small plastic protusion that held it in place. Once it wears, you are out of luck. Have not seen this myself, but thats what he tells me..
Regards
chris
that's correct, it's just a plastic clip protruding to grab the gap on the stylus. if it's broken, you may just have to put a tape or sticker around the stylus to make it tighter.
there are 4 screws (one under the void sticker) where the battery goes. i just took mine apart to tighten slider. it's back to sliding smoothly & tight, however, there's still a noticeable gap (between the screen plate & keyboard plate).
anyone knows how to eliminate this gap (about 2mm)?
Try this solution: http://forum.xda-developers.com/viewtopic.php?t=15120&highlight=loose+stylus
Cheers
Frankman
I use 1 layer of tape around the stylus. spanning the groove in the stylus. This seems to make it a good bit tighter, but does not fix the problem entirely. Hope that helps..
Regards
Chris
i dont like the idea of having tape on my stylus... looks well tacky going into a metting with clients!!
so i took some black insulation tape and made small squares with an art blade and stuck them to the inner edge of the holder... now it sits there nice and tight like a school girl
S O R T E D!!!!
cheers for the help guys/gals.... if any....
An idiot friend of mine put a blade of grass in the stylus holder and now it wont come out. How do I fish it out? The good thing is, my stylus doesn't slide out so easily anymore.
I have also encountered this problem(i got my BA 6 months till now), however it is not that loose as what ur described. at lease it never drop out when i was outside. (after reading this i become worry about it)
I used to own a IPAQ 5550, when i got my BA, i thought the quality of the stylus is better than ipaq's plastic stylus(should have some heavy stuff insde..), i like the BA's metalic stylus.
Now i found that the IPAQ plastic stylus + the spring-like system inside the whole is much better...i want to have one BA + the metalic stylus + the spring-like system to hold the stylus....
if some day i am that unlucky to lost my BA's stylus i will try to use the 3-in-one PDA pen... once it lost one, i may lost another... i wont use normal stylus if it happened.
DJUPLIFT wrote[/quote]
i dont like the idea of having tape on my stylus... looks well tacky going into a metting with clients!!
You have to use that "invisable" tape and only the keyboard and buttons if its a Director or above! :lol:
Click to expand...
Click to collapse
Loose stylus - Stylus falls out
This has worked for me. It's been 5 months, and it still works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Reassemble your BA.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Yet again we're having to come up with dodgy (although well thought out) solutions to HTC's shoddy design flaws. My BA is about 3 - 4 months old and its up to this already. I keep finding my stylus on the floor.
Thing is, all these solutions void the warranty and I have to take mine back soon (See the Xray thread ) and am hoping for a replacement on insurance.
The P800 and XDA2 had this problem as well, but surprisingly I have NEVER lost a single stylus in my life! I always just happen to find them again. One time I found my P800 stylus 2 days later in the street between my college and my flat :S
Re: Loose stylus - Stylus falls out
N2O2 said:
This has worked for me. It's been 5 months, and it still works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Reassemble your BA.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Click to expand...
Click to collapse
Great idea! It's perfect!
THANK YOU N2O2
N2O2
You just made the wiki hall of fame
http://wiki.xda-developers.com/index.php?pagename=BA_Sty_stopper
Any Kentucky Fried Chícken fans out there?
After losing 5 styli - not only because they were loose in the holder (one went on the motorcycle after I missed the holder hole and then let it go) I came up with this junky solution.
The KFC corn cob holders are a good diameter (had to add a thin layer of tape) and just long enough to be modifiable to add a knureld part at upper end. At at least one of their restaurants I found them outside of the front counter and was able to obtain a few cheap spare emergency styli
Oh well.
:lol: :lol: HAHAHAHAHA You are grade man .....
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
I'm OK with taking things apart and putting them back together. Are there screen shots of someone taking the Blue Angel apart and fixing the stylus clip?
Please post
or even a video clip?
DIY Blueangle fix
Hi,
I had been using HTC BlueAngle for almost 2 years and very happy with it.
When I first got it, I dropped it the next day. The stylus holding clip was broken off. At first I tried to put tapes around the stylus to hold it in place.
It didn't work out at the end and I opened it up and put a piece of foam in the stylus tube to add fiction and avoid it fall out. I worked nicely.
I still love my BA even I am using HTC Universal most of the time.
Cheers
I have the same problem. Nice tip, thanks, I'll consider it too.
u dont have to do all that, the main reason it becomes loose is the bit of plastic that is attached to the frame gets weak... just open the back with the specialist screwdrivers which can be bought off ebay for nomore than £5 and either superglue it back into the correct place or just rest something like paper to make the plastic bit stick out a bit more so that the stylus gets a tighter fit....
go for the quick fix...just stick a 3mm width masking tape on the top part of the stylus and it is good to go. adjust the width of the tape according to how tight you want your stylus to be in place. HTH
Anyone know how I can purchase this? I got a tiny scratch on the screen.. well, its more like a crater. Its almost like someone took a needle and dug a chunk out of my screen.. Like a crotch-located steering wheel, its driving me nuts.. Big time..
What are the differences between the GSM and the CDMA screens? Would a Verizon store be able to order this part? I don't want to send it anywhere simply because I don't wan to relock and reflash and wait xyz amount of time to get it back.
To access the digitizer, do we have to go from the battery on up or can it be removed from the top or sides somehow? Thats an important question too.. as removing it from the bottom-up would require a complete dissassembly of the phone.. and I do mean complete.. speaker, radio, motherboard, keyboard, hinges.. ugh..
Or perhaps from the middle? I am pretty sure there are screws on the back. I just wonder what the result would be.. I don't care if it requires purchasing the bezel either.. I just want to make it clear, that the screen works fine and the digitizer senses input on the spot where its 'injured'.. I'd say its no more than.. 3 pixels height.. 1 pixel width..
yeah, I'm nuts. But you'll benefit from that if I end up detailing the digitizer replacement process. Once I have my new screen on I'll try to see what methods I can use to get the old one looking brand new.. I'm ready to wet sand this bastard. jk
Was looking at the ghost armor CDMA page when I (finally) decided that the ebay digitizers were the same damn thing as my Verizon CDMA.. Only difference is the cut out for the front vid cam.. Now, electronically.. is this true? This looks like it would physically work.
http://cgi.ebay.com/For-HTC-Touch-P...AU_MobilePhoneAccessories?hash=item27adf15e64
This digitizer would mate up with the 'slider flex cable w/ earspeaker' as seen on this page..
http://cnn.cn/shop/t7373-touch-pro2-rhodium-c-277_815.html
I'm not saying anything for certain.. its mostly educated speculation.
Hi There!
Recently I purchased this:
http://www.ebay.com/itm/28076731850...cat=0&_nkw=280767318505&_rdc=1#ht_2724wt_1163
It's ok, except for the part where the bracket is not secured properly to the mount, so after a bit of rough driving, it shakes loose and falls to the FLOOR!
I previously had a great unit for my HTC HD2 but I have yet to find a good replacement.
I like the spring lock mechanism of the above unit, and the fact you can tilt and turn it, so those are features I like, but I'd like bigger "feet" to ensure it doesn't slip downward.
Anyone able to recommend something PLEASE?