I have installed a light version of Revolution HD rom and am not overclocking past defaults.
I do however want to undervolt. ATM ive set screen off profile to max out at 600 - what can i do do undervolt?
Can i keep the rom but flash a different kernel? If so, which one?
The kernal that rom uses is already undervolted, so you dont really need to unless you want to try and squeeze it as absolutely low as your handset will allow.
i see - where do i find the exact details of this?
This is the thread for the kernal that Revolution HD uses.
http://forum.xda-developers.com/showthread.php?t=835608
thanks, but from what i understand the kernel isnt undervolted - its unvolted...
Hmm, i was under the impression that lower freqs were undervolted and as it approaches 1.2Ghz the voltage approaches the highest value of stock voltage.
even if this was so - i would see no benefit as i use stock max clocks
Related
Alright, so set cpu has been updated and it says it has a beta setting for the evo. I was reading through the comments and one of them says that setcpu is only for controlling the cpu speed from standard 1ghz and lowering. If i wanted to overclock to 1.2(I think that's the highest i've seen around) I would have to get a custom rom. So.. i have baked snack v7... is that what they are considering a custom rom? or do i have to have a supported overlcock custom rom. then i use set cpu to control the cpu speed.
?
hah thank you.
derik123derik123 said:
Alright, so set cpu has been updated and it says it has a beta setting for the evo. I was reading through the comments and one of them says that setcpu is only for controlling the cpu speed from standard 1ghz and lowering. If i wanted to overclock to 1.2(I think that's the highest i've seen around) I would have to get a custom rom. So.. i have baked snack v7... is that what they are considering a custom rom? or do i have to have a supported overlcock custom rom. then i use set cpu to control the cpu speed.
?
hah thank you.
Click to expand...
Click to collapse
You can only overclock the CPU by using a custom kernel, and at this point in time you lose camera
http://forum.xda-developers.com/showthread.php?t=686240
I am new to the setcpu app I am wondering how do I know how much frequency my min and max should be to help my phone out more. Can anyone help me on that plz?
Sent from my PC36100 using XDA App
It will depend on which ROM and kernel you're running, but generally, overclocking doesn't do much good for you. I do however run my Main Max @ 1113 and Min @ 245. I then have a profile set for Screen Off Max @ 245, Min @ 245. This has helped a lot with battery life. This is on CM6.1.1 and the SBC stock kernel.
Also, there are the Scaling options. They will vary based on the kernel you're using. Generally, their names speak for themselves, so pick appropriately. I use Interactive when available, or Ondemand as a second choice. If you choose Performance, you will stay clocked at the highest speed until over ridden by a profile, so don't bother with that one unless it's for testing only.
One thing to think about is that Setcpu doesn't play well with HAVS, so if you're running a kernel with that built in, they will be fighting each other.
Also, if you're running a stock based rom with a stock kernel, you will need to disable Perflock if you want Setcpu to be able to really do it's job. So, while in Setcpu, tap Menu > Perflock Disbaler and attempt to disable perflock. Once it is successful, pick set on boot and close that window. Now Setcpu can work properly and you can start saving battery.
If you're primary goal is to get amazing battery life, I highly reccommend you try some of the new SBC kernels that have trickle charging built in. That's what I've been using since they came out, and it is amazing what a little tweak can do for you. SBC Kernel Thread
What are the safe/stable clockspeeds for underclocking and overclocking my Desire Z? Also, what app do I use? Like, I don't mind paying for the app (as long as it's not too expensive)
Sent from my HTC Vision using XDA App
SetCPU can be used to overclock if you're rooted. Depending on the ROM and Kernel combination, overclocking to about 1.3ghz is usually safe. Some go up to 1.5ghz or even 1.8ghz, but are often quite unstable depending on other configurations you have in your ROM.
As far as underclocking goes, some custom kernels clock all the way down to 122mhz, I've been using a streamline5 kernel on CM7 (which offers 122mhz min) and haven't had any ill effects with this.
I have the Virtuous Sense ROM (with it's default kernel, although it does have other kernels which can give other cpu speeds), right now but might try out another ROM soon (maybe) do you know what's the min and safe max for this ROM?
Also, can I just set a particular clock speed (e.g. 500MHz) and it should be ok or is there any stability difference between say 500MHz and 505MHz? Just curious. I looked at SetCPU and it looks like a good one. Also, if the clock speed I set makes things go wrong, can I revert it or can I get stuck with it and need to do a wipe?
Sent from my HTC Vision using XDA App
zaghy2zy said:
I have the Virtuous Sense ROM (with it's default kernel, although it does have other kernels which can give other cpu speeds), right now but might try out another ROM soon (maybe) do you know what's the min and safe max for this ROM?
Also, can I just set a particular clock speed (e.g. 500MHz) and it should be ok or is there any stability difference between say 500MHz and 505MHz? Just curious. I looked at SetCPU and it looks like a good one. Also, if the clock speed I set makes things go wrong, can I revert it or can I get stuck with it and need to do a wipe?
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
No, there's no need to set a particular clock speed. Just whatever works for you. I wouldn't recommend going under 800mhz, as the phone will really really bog down even with normal use.
I haven't used that particular ROM, but I'm assuming anywhere around 1.3ghz should be safe on the upper limit. Like I said before, anything above that might start to cause issues. You might also want to consider the battery life implications of severe overclocking.
You can change the clock speed any time you want. If you're having wakeup or heat or any other issues just go back to SetCPU and change the max clock speed again. You can also use profiles in SetCPU to change the clock speed when the phone is overheating, or when the screen is off, or when the battery gets to a certain %. There are tons of posts detailing how others have setup their SetCPU profiles.
One last note, don't forget to check the box for "Set on Boot" in SetCPU, this way your changes aren't undone on reboot.
Thank, I think I got everything I need to know in your last reply
I'm on CM7, with the CM7 kernel, and clocked in at 1.5GHz, and have no problems, and the rom is super fast. And I use SetCPU.
I have htc wildfire s ...i hav rooted ...i want to overclock it 806 mhz.....pls tell me the procedure to overclock..
I am using htc wildfire rom ..pls help
First you need a kernel that supports overclocking.
If you using a stock Rom then look for the kernel that matches your Android version eg. 2.3.3 or 2.3.5 you will find them in the development section posted by Jikantaru
If you install a custom Rom then it will most likely have an overclockable kernel baked in.
To change clock settings I recommend 'no frills CPU' search it in the market or you could use set CPU.
Once you install one of the above apps then change the min and max sliders to the desired frequency.
if we over clock it much does it effect the speed or hardware of the phone?
Your phone may hang.
There is SetCPU for XDA members:
http://forum.xda-developers.com/showthread.php?t=505419
RRRb50 said:
if we over clock it much does it effect the speed or hardware of the phone?
Click to expand...
Click to collapse
You will definitely get better performance and it shouldn't cause you any problems.
Use no frills CPU I find its better than set CPU, when restarting your phone set CPU doesn't keep your overclock settings even though its set on boot.
As for the govonor settings I would choose smartass2 and noop for the scheduler.
I would keep the minimum frequency on 245MHz it can go lower but it could cause some issues (lag and slow unlocking and waking)
Note: not all cpu's are capable of running at the same speed, I'm lucky mine can run at 806MHz but some people have issues.
If you notice any problems like freezing etc, then drop the speed to a lower frequency until you find the sweet spot for your CPU.
I had mine at 806 MHz with no problems
Sent from my NookColor using xda premium
so it wont cause hardware problems only lagging and other stuff
RRRb50 said:
so it wont cause hardware problems only lagging and other stuff
Click to expand...
Click to collapse
Should be fine mate.
But remember if in the very unlikely event something does go wrong I wont be held responsible.
youll have to need an overclock kernel for that. (and a rom which supports one)
go for dust kernel or cake kernel! These two are well known for high end kernels!
Hi i have ARHD on my phone with the XM Kernel. I was slightly suprised in the Trickster MOD app, the max clock speed is 1.3ghz. Yes i know i can OC to 1.5 but im not sure what is setting this. When i had ARHD installed with stock kernel it was showing 1.3 as default. I assume that was set by the ROM. But i installed this kernel and still has 1.3 as the default.
Also the default govenor settings for the gaming one has the boost_freq set at 1300000, which is 1.3ghz, that can be changed to 1.5 also. But surely the boost freq would be the max freq no matter if you move the slider to 1.5 in the basic controls? But i would be suprised that the gaming govenor would underclock the cpu, surely for gaming you would want the phone maxed out?
Is this expected with the XM Kernel and the ARHD? And if so, is there any things i can change in the govenor settings to make sure it performs at absolute max?
It's kernel related; Xmisters' kernels since 188 have a hard cap(1.3Ghz) by default, but using trickster mod, or another o/c apk, you can raise it to the stock 1.5Ghz(tick 'set on boot' to ensure it stays at 1.5) The best settings are trial and error, tbh, I use touchdemand/sio though smartmax seems to be the best balance.
Thanks for the answer. i can change it to 1.5 easy enough, but if you look in the govenor control, the boost_freq is is set to 1300000. If i left it at that, would it prevent the cpu from going up to 1.5?
Danw20 said:
Thanks for the answer. i can change it to 1.5 easy enough, but if you look in the govenor control, the boost_freq is is set to 1300000. If i left it at that, would it prevent the cpu from going up to 1.5?
Click to expand...
Click to collapse
you have sleep (lowest CPU can go), ideal freq(the speed the CPU aims for while awake), touch poke (when you touch the screen), boost (what it boosts too to prevent lag) and max (CPU flat out)
Setting the boost to 1.3 will still allow the could to run at full speed.
Sent from my HTC One X using xda app-developers app
That makes sense, cheers. So its probably a good idea to leave it as it is then.