Related
I just ordered some Realook screen protectors from Amazon today. The stores here did not have any screen protectors of any brand for the Vibrant, and I just didnt want to wait any longer without protection. Then to my surprise a few of the Bell Mobility dealers just got in some iShieldz. They tell me they stopped carrying other brands because they found these were the best protectors hands down. Can anyone else comment on how they compare to the Realook protectors.
i recently bought some cheap ebay protectors for my galaxy s and to be honest i was not satisfied with the finish and bubbles on my screen. so i came on here and researched on screen protectors there are 2 kinds of them : one is water based screen protector ishields is one of them and second is dry application. i did not want to risk my device with water damage and went with realook "SP". ishields are not smooth and have that rubber feel to it just like invisible shields. i would recommend reallook as long as u do a bubble free installation , install it in ur bathroom after u take a shower cuz the dust particles settles down in steam
i will post some pix of my samsung with realook on in next post
here s a 10 % off coupon if u order from amazon "2ZDlV2W5"
Never heard of iSheldz, but if you can, go in store and see if they have any demos to get a feel of it. If it feels like rubber, then well, it's your call. I don't like that rubber feeling and went with Realook. Realook is like a piece of plastic per say. You don't have that rubber feeling and after awhile, it will feel just like the naked screen, for me anyways.
Your call.
I'm in the market for a screen protector too. I heard Realook is better than iShields but, I like the rubber feel better.
Anybody with Realook, is the installation easy?
Is Realook installation easy?
For me it was not very easy, and not very difficult. I got frustrated initially by dust particles (which for me were impossible to avoid) causing bubbles. The key turned out to be using scotch tape to remove individual spots from the underside of the film (which is exactly what the directions suggest).
The other trick was getting the positioning exactly right. The fit is quite precise, so 1/4mm off on the angle and it will run off the side of the glass at the bottom. I ended up using a piece of tape on the top surface of the film at both the top and bottom to help in both lifting it to remove dust particles and to get the positioning just right.
It's a dry application, which makes it less dangerous as far as getting liquid in the phone, but you can't slide the film around to position it.
The end result though is well worth the 10-15 minutes of effort it took me. It's probably as close to the original glass look and feel as is possible.
I took an advice from another user here saying to run hot water in the bathroom so that it will be filled with steam and result in less dust in the air. I did just that. Took a shower and then immediately started to apply the screen protector. Took me two tries. Make sure to have scotch tape ready so you could peel it off if you messed up.
Sent from my SGH-T959 using XDA App
DKYang said:
I took an advice from another user here saying to run hot water in the bathroom so that it will be filled with steam and result in less dust in the air. I did just that. Took a shower and then immediately started to apply the screen protector. Took me two tries. Make sure to have scotch tape ready so you could peel it off if you messed up.
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
Probably want to keep the tape out of the bathroom when your taking the shower to ensure the proper adhesiveness.
iShieldz look like Zagg lite, they feel like Zagg kinda sticky and after a few weeks they make the screen look like crap.
My vote is for Realook...
Just be patient and do it in a place where you are not going to be disturbed for the few minutes it will take to get it on perfectly. Doesn't even look or feel like it's there. You'll love it and you get two for the price.
real look it looks amazing and very easy to install ...
I use Realook and didn't find it to be terribly hard to install. It's the best looking I've ever seen and it's smooth, so there's no finger friction on the touch screen, which is a requirement for me (Swype user). If I were going to do it all over again I'd definitely go with the Realook again. I can't imagine anything better.
I somehow got a nasty scratch on my realook today. I really don't know how. But I want to cry lol better that than my phone I guess
Sent from my SGH-T959 using XDA App
I just re-ordered the reallook sp's (2 pack). Anyone want to split the cost?
Yes please
Sent from my SGH-T959 using XDA App
wow I ordered a realook screen protector, amazon said a delivery date on the 20th, I got it 2 days after I ordered it. It was hard as hell to install, I got dirt and fingerprints all over my first one, then I tried the other, took my time, had allot of dust on the screen causing bubbles, got some scotch tape and slid it under neath and took off the lint all over it after I washed it with water, sqeegeed it on, it was tedious but it doesnt look like I even have one on it, freakn amazing, next time i put one on it'll be much easier. First time took a while lol
Realook suggests to spray some water in the area that you are going to apply the SP to cut down on dust. I sat under a ceiling fan, on low, when I put mine on. Just take your time when applying it and you will be happy with it. I am with mine .
I cannot stand the installation procedure needed for the screen protectors. Every single time: I use the "provided micro fiber" cloth to remove dirt and lint and the apply. EVERY TIME I am left with tiny lint,, micro specs of air dust etc. between the film and the screen, and a small little bubble here and there. It drives me crazy. Call me obsessive compulsive but it take me about 3 screen protectors until I finally get it right. Anyone aware of any screen protection technology that will help me avoid this outcome?
I don't, but I did read that if you apply it in the bathroom after running hot water and steaming it up real good that it will help that problem a lot. I plan to try that when I get my first screen protector this week.
Sent from my SAMSUNG-SGH-I897 using XDA App
Hard type screen protectors will solve your bubble issues. Martin Fields screen protectors is pretty much impossible to have bubbles stuck inside it.
However it won't solve your dust problem. If anything, it's much easier to see dirt and other imperfections stuck between the screen and a Martin Field protector.
Or you could try one of the crystal screen protectors from boxwave. I had your problem too with my first 2 screen protectors, and it seemed that I couldn't just get them on there without a problem. With this one from boxwave, I just wiped it off with the provided micro-fiber cloth and used the bubble-elimination card to remove any possible bubbles under the screen!
http://www.boxwave.com/
Get the ones from ATT. I have tried Bodyguardz, Zagg, Stealth Guards, and some generic BS from eBay. All of those were the type you apply with the solution (and have that dreaded orange peel look) and you have to wait for it to "cure" and it is extremely easy to get bubbles stuck in them.
The ones from ATT on the other hand, are completely smooth and truly invisible. They are a stiffer material and you do not need application solution. I am very happy with them and for 9.99 you get 3 of them. If you mess one up by getting some lint on it or whatever, you can just wash it with soapy water and spray it down with some water+baby soap and re apply it that way. Very easy to get the air bubbles out that are caused by using the solution. Again, they can be installed with no solution at all and if done carefully, it should look like nothing was ever installed on the phone
http://www.wireless.att.com/cell-ph...038&q_sku=sku4770252&q_manufacturer=&q_model=
I got them from a local store for 7$ since I got a discount. Those above ^^ from BoxWave seem extremely over priced. For 10$ you can't go wrong with the ones from ATT.
I am using clarivue not even a single dust, lint, inside. It's the quick and easy 3 layer type screen protectors.
Here's a tip ... go to the bathroom and turn on hot water on sink or whatever to create humidity that would trap the dust or w/e in the air ... and it makes this easier to apply.
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
+1
I had my iPod Touch for years, in and out of pockets with keys and pocket-knives and cell phones, dropped countless times, two little kids messing with it all the time, accidentally sliding it face-down across surfaces, and so on. Never used a screen protector, never got a single blemish or scratch. And that was basically plain old arsenic-free glass. The Captivate is made with Corning's high-tech Gorilla Glass.
Sure, either could still scratch or break. But it's like getting a car with an expensive paintjob, and then covering the whole thing in Scotch tape so it won't get scratched. You end up with something that looks god-awful 100% of the time, because you're afraid something might happen to it that would affect how it looks. Pretty much any time someone hands me their smartphone or DS, it is a scratched, smudgy, dusty mess because of some $40 screen cover they have on there. I always try to point out that it seems odd to make your screen look terrible on purpose just because you're afraid of you might make it look terrible on accident. I used one good one once, that you couldn't even tell was there, but the first time I took it on a flight it turned into smears of rainbows.
use a piece of clear packing tape to remove the dust. running the shower helps bring dust down but there will be some lint from the cloth. dont lean over it, a lot of "dust" is dry dead skin or dandruff so if you have dry skin or dry scalp dust will fall on it. also stop being so anal.
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
+1
I don't need no stinkin' screen protector. I mean unless I know my phone is going to be dragged across macadam but then a screen protector won't help, will it.
Gorilla Glass... Screen Protector unnecessary... I have always used a screen protector too on previous phones but the screen on this phone is rugged.
I used to be the same way as you guys, "I don't need a screen protector because it's been through everything and still works perfectly!!" Yet, one day I found a scratch on my screen that I have no idea whatsoever where it came from. So, I got this Boxwave ClearTouch Crystal screen protector, and you literally cannot tell it is on there. It feels just like the glass (con for me actually, I prefer a paper kind of feel) and doesn't scratch easily at all. Plus, I installed it in a dusty room and there was no lint or anything else under the screen. It even comes with a thick card to remove bubbles once it has been applied. So, if you're even slighty, .000001% scared of getting lint trapped underneath the screen, go with Boxwave. I vouch for its clarity and ease of installation. Also, my screen is just as sensitive as before, as I've tried BARELY touching the screen and it still would pick up a touch.
And, in the rare event that you did get dust glued to the screen, it is completely washable and rewashable, so it is a little expensive, but well, well worth it.
Oh, and there is no adhesive whatsoever, not even water is needed. Just peel and go.
magnumrt562 said:
Gorilla Glass... Screen Protector unnecessary... I have always used a screen protector too on previous phones but the screen on this phone is rugged.
Click to expand...
Click to collapse
i listened to this
totally terrible advice. not that i care but i have about 20 microscratches and a couple decent sized ones....
it takes time to learn how to put screen protectors on... I have probably put 500 or so on all different types of phones you just wipe it clean tilt it so that you can make sure there are no dust particles... then you pull the backing off of the protector a few inches apply to the designated area and take a credit card and follow the rest of the protector down... works everytime
iamamp3pimp said:
i listened to this
totally terrible advice. not that i care but i have about 20 microscratches and a couple decent sized ones....
Click to expand...
Click to collapse
I second this . there is no such thing as 'unscratchable glass' some very expensive sunglasses use to have that warranty , guess what , they dont anymore ...
although I have to say the argument about HAVING YOUR PHONE LOOK UGLY JUST IN CASE SOME ACCIDENT CAN HAPPEN TO MAKE UGLY made me laugh , I d never have a phone without one my advice :
Just buy a few cheap ones on eBay and master the trick when your bored , after 3 times it should be installed perfectly , I also noticed if you have light scratches already on it , the screen protector hides them so thats a bonus
Ive tried SO many screen protectors. The only one I have been happy with so far (and VERY happy at that) is Realook. They are SUPER clear, thin, and very hard. You do not lose the glassy feel or the crisp vivid look on the screen. Ive put them on a few phones now, a few Vibrants and a Mytouch Slide 3g (my gf didnt even know i had put it on there till i told her). Its $10 for 2 protectors and I HIGHLY recommend them.
http://cgi.ebay.com.sg/REALOOK-AT-T-Samsung-Captivate-AFP-Screen-Protector-2PK-/250674134359
Siks said:
I haven't had a screen protector on my Vibrant in almost 2 months now & even with constantly putting it in my pocket with my keys, dropping it once onto my driveway & even fumbling it into bouncing off a brick wall one time I have yet to scratch my screen. The rest of the phone is dented & scratched but the screen is still beautiful.
Click to expand...
Click to collapse
I have a tiny little chip right in the middle of my screen on my Captivate about a cm underneath the AT&T logo. It has taken less abuse than yours, and it even has a screen protector on it. It looks like the kind of chip you would get if a piece of gravel hit your windshield a little too hard.
Your mileage may vary.
Hydrocharged said:
I used to be the same way as you guys, "I don't need a screen protector because it's been through everything and still works perfectly!!" Yet, one day I found a scratch on my screen that I have no idea whatsoever where it came from. So, I got this Boxwave ClearTouch Crystal screen protector, and you literally cannot tell it is on there. It feels just like the glass (con for me actually, I prefer a paper kind of feel) and doesn't scratch easily at all. Plus, I installed it in a dusty room and there was no lint or anything else under the screen. It even comes with a thick card to remove bubbles once it has been applied. So, if you're even slighty, .000001% scared of getting lint trapped underneath the screen, go with Boxwave. I vouch for its clarity and ease of installation. Also, my screen is just as sensitive as before, as I've tried BARELY touching the screen and it still would pick up a touch.
And, in the rare event that you did get dust glued to the screen, it is completely washable and rewashable, so it is a little expensive, but well, well worth it.
Oh, and there is no adhesive whatsoever, not even water is needed. Just peel and go.
Click to expand...
Click to collapse
Thanks for the info on the Boxwave screen protector, I've been wandering if it's as good as it looks.
In the malls near me now, there are little carts (you know those areas of the mall, where the cart/carny people are) that have people with small steady hands...
Invisible Shield it is called. They give you a lifetime warranty on the cover. They put it on. They will even cover your entire phone if you want (the back of the Captivate I am thinking of getting covered to avoid scratches on the metal back), and if you get a replacement phone for some reason, you only pay a portion of the price (material only) and they put it on again.
They use some sort of silicon liquid (snake oil... was probably just water) to aid in putting it on, and mine is perfect. Had a couple bubbles with the liquid still in it, but true to their word, it evaporated (through the protector) and it was perfect the next morning.
I jumped at this opportunity after totally FAILING at putting on a protector on my Tilt 2 (two packs of 3). On that phone, I took an exacto knife to cut off the excess I was so bad at it. I gladly paid $20 to have someone else do it and give me a warranty on it.
Invisible Shield. Check out your local mall.
Jeepsdaddy said:
I cannot stand the installation procedure needed for the screen protectors. Every single time: I use the "provided micro fiber" cloth to remove dirt and lint and the apply. EVERY TIME I am left with tiny lint,, micro specs of air dust etc. between the film and the screen, and a small little bubble here and there. It drives me crazy. Call me obsessive compulsive but it take me about 3 screen protectors until I finally get it right. Anyone aware of any screen protection technology that will help me avoid this outcome?
Click to expand...
Click to collapse
I think the gorilla glass is pretty resilient. Check out this youtube vid.
http://www.youtube.com/watch?v=6xASJobjD68
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
I use painters tape after I clean the screen (before applying of course) to make sure no other dust or hairs are on the screen. Use a can of air to blow away crap in your work area also.
Sent from my Galaxy Nexus using xda premium
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
Will this work with SGP Ultra Crystal screen protector? or are they only the non-water applyable?
Can't speak specifically for the sgp but I've been using the wet application method on all my dry application protectors for some time across at least 5 different phone models with no issues. Much easier to apply accurately than dry
Sent from my SGH-T889 using Tapatalk 2
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
I read some where that you should apply it in a bathroom and before you start get a spray bottle and put water in it. A couple sprays in the air before... No dust works for me
Sent from my SGH-T889 using XDA Premium
Well I just got 2 more cheap protectors in the mail, the first one I tried to get perfect, and each time I tried to get rid of a piece of dust it would get worse. The second one I have one bubble and I gave up. Fine. I have a bubble... oh, and they are cheapo reflectors, and supposed to be matte... so now my screen looks pretty horrible. Sigh. Whatever, my screen is protected. I will get an SGP later and figure something out in the mean time... maybe take them to a tmo store since they did it for me last time and it came out perfect somehow. I think my house is just too dusty, and there's no way to change that. I live in the desert, I have cats, the place is old. Sigh.
omg just did both of the note 2's and it took about 30-40 minutes, ridiculous, but afterwards looks nice till today i had the damn T-Mobile protector on it lol i got tired of seeing T-Mobile =P
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
phreshjoker said:
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
Click to expand...
Click to collapse
Well i did it at my dining table and i regretted doing so because I ended up getting a few particles underneath, but all you need to do at that point is take any type of sticker (mine came with 2 stickers which were called Dust Removal stickers, but its truly a regular sticker lol) so I had to use that several times, but the final result is great
I ended up ordering the SGP Ultra Crystal and also ordered MobC from amazon (http://www.amazon.com/gp/product/B009M7TZYO/ref=oh_details_o00_s00_i00) which ended up coming in first, so I am still waiting for the SGP but honestly i do regret ordering them because the MobC are freakin great, crystal clear, and i have no regrets of putting it on!
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
For with app screen protectors...exactly as Kobe mentioned. Couple of drops / 1 part dish washing liquid to 5 parts water (distilled water if your tap water has too much minerals)...just so the solution is slippery enough for the application process. Run your finger nail down the edge of the credit card / tool your going to use to ensure there are no nicks / sharp edges that will damage / crease your wet app screen protector.
Steamed bathroom also helps.
I recommend dry applications for flat surface...wet applications for curved surfaces.
With dry app screen protectors, those clear / ultra clear packs off of eBay usually work well. The only issues I have seen is that the adhesive may get weak over time (if you need to lift protector to remove dust then press down again) and initial cutouts maybe hard to see from pics. Eventually these dry app screen protectors fall to 3/5/? packs per <$1 ???
Position the dry app screen protector then apply / remove film. There will probably be dust, pet hair, etc. Lift up one corner / side / section at a time and slide the shipping tape between the screen protector and screen (sticky side of shipping tape against sticky side of screen protector)...then press dry screen protector down on the shipping tape which will also press against the screen. Carefully lift the corner / section of the screen protector...then flip the shipping tape over and slide back under between the screen protector and screen (sticky side of shipping tape now facing screen) if needed. Usually the particle is on the sticky screen protector side, but sometimes it maybe stuck to the screen side. The idea is to use a shipping tape with strong enough adhesive to remove the particle without ripping off / damaging the screen protector adhesive. Painting tape adhesive maybe too weak in removing any dust / pet hairs...UPS grade shipping tape maybe too strong...I like Staples equivalent shipping / packing tape...it has just enough adhesive strength to remove any dust / pet hairs.
Hope some of this helps.
What works for me:
http://forum.xda-developers.com/showthread.php?t=1988725
Got my spigen... I am probably never buying from anyone else. Well, I dunno, but from the packaging to the application I felt like I was using quality. I thought I had ordered the ultra crystal but I actually went for ultra oleophobic for some reason... and I am crossing my fingers that the surface tension changes after some use (doubt it) but it does do what it says, finger prints do not stick. However the down side is the s pen doesn't feel nice against it (it did feel really nice against the crappy matte protector, felt like a pencil on paper, but I couldn't stand the rainbow effect, maybe I will try a spigen matte in the future). Any way, I used the "hinge" technique I saw somewhere online and it worked pretty well. Got 3 pieces of dust under the screen (1 on the screen, 2 on the bezel) and I used some scotch tape to life the protector and one of the included dust removal stickers to quickly take care of the problems.
the protector is FREAKING INVISIBLE! right now the screen is off and I can see reflections, and I can barely make out where the protector ends.
Thanks for everyone who gave me their tips and tricks, I finally have a screen protector on my note that I am happy with.
Also, for those people going naked, it doesn't affect my screen but I saw I already have 2 minute scratches on my screen. I keep my phone in my pocket on its own, and somehow I managed to scratch the screen already (got on release day). I have wasted a bunch of cash getting a screen protector on that I was happy with, and I might spend more in the future, but at least I know that if anything terrible happens I can replace the little piece of plastic instead of forever having to deal with a scratch.
EDIT: playing around with it some and then wiping it off, I already am fine with how the S pen feels. I think it was actually sticking to whatever they used to apply the outer layer of protection that you remove after applying the protector. A little bit more drag then on the naked glass, but I like that I can now get more of a tactile response of my writing. I am hooked on Spigen.
I do all my screen protectors at the dinning room table in about 2 mins with perfect results every time. I attached a few screenies but they really don't do it justice. It is insanely hard to get a good picture of something clear when using a flash. the specks of dust that are noticable are on top of the protector not underneath. I'm using the spigen oleophobic and love them.
I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.
The xtremeguard screen protectors are really good, and they can be found for under $2.
mprasolov said:
I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.
Click to expand...
Click to collapse
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.
BigOkie said:
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.
Click to expand...
Click to collapse
I guess I lucked out with my choice of screen protector!
Not necessarily. I bought these SAMAR crystal clear screen protectors, managed to apply one without getting any dust or air bubbles. It has all the cutouts, the fit is good, and it is quite smooth when swiping, very happy with it so far. To top it all off it is dirt cheap and you get 6 protectors all with cleaning cloths! I've read others on here who have been happy with this brand too. Would definitely recommend.
use a drop of water when u install. it'll help take out bubbles.
also you can reapply these, just rinse in soap water then water, then shake off excess and apply. squeegee out the water - should be next to nothing.
ktamondo said:
The xtremeguard screen protectors are really good, and they can be found for under $2.
Click to expand...
Click to collapse
True. And even with that. I got one first and tested before I got backups.
I use an IQshield screen protector and it's nothing short of pure awesome. No bubbles at all, and it's so smooth and dried hard. It feels like glass.
You get what you pay for. I bought the spiegen Crystal for 10 bucks and they went on perfect and looked perfect and felt pretty good to you cant even tell its on unless you look at the earpiece closely. But there's always better! I just recently bought a Nillkin Glass screen protector with 9h hardness and olephobic with rounded edges and its gonna be getting here in a week or so and that should be way better than a cheap or high quality screen protector!
This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
second, and heres the silly part: I make sure the screen is completely wiped, and blow on the screen itself with DRY LIPS as im applying the screen protector face down. This blows off any dust that may settle between the time you apply the screen, and make sure lips are dry as to not blow moisture onto the screen.
There really isn't any fool proof method for applying screen protectors without dust, but without some sort of clean box with a built in HEPA filtration system, this seems to work well for me 80-90% of the time, versus just applying like normal.
unvaluablespace said:
This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
.
Click to expand...
Click to collapse
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.
Caelrie said:
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.
Click to expand...
Click to collapse
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol
The moisture will get out over time. Its just like having windows tinted
Sent from my Nexus 5 using Tapatalk
unvaluablespace said:
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol
Click to expand...
Click to collapse
It doesn't matter. Even dry-applied screen protectors go on better this way, and any moisture completely dries out quickly anyway.
Spend a few hundred dollars on a phone and then buy the cheapest cases and screen protectors you can? Doesn't make sense.
I'll pay the extra $8 for a Spigen screen protector and a quality case that match the quality of my Nexus.
Sent from my Nexus 5 using Tapatalk
Spigen could've tried a bit harder and made all the cutouts. Even the temporary screen protector that comes with the phone has those. I think most screen protectors will be similar at the $1+ range but you can't expect much from ones that cost $0.25.
xtremeguards didn't have bubbles for me. Buying 6 of the same screen protectors and then saying all of them have problems doesn't make sense.
I'm assuming the OP means the bubbles are from the edge of the cutouts not sticking down which is a common issue with cheap screen protectors.
the cutouts are not made well so the screen protector itself is warped at the cutouts for the speakers etc so its not flat and does not stick down creating bubbles there.
Just install in steamy bathroom. The steam prevents dust from floating in the air.
Sent from my Nexus 7 using XDA Premium HD app
I got this Nillkin one: http://dx.com/p/277084. I only had one. Applied by using the "hinge" method. Went perfectly. Cutouts are perfect and bubbles are removed very easy (easier than other screen protectors I've had).
I used a little wet cloth to make my screen wet and to remove dust. At first it feels very rubbery, but after using it for a day or even less, it feels just like the glass!
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Tinderbox (UK) said:
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Click to expand...
Click to collapse
For dry applies, look up the hinge method on Youtube, it makes applying screen protectors a breeze, and gets things perfect every time the first time. As far as dust goes, I recommend shining a LED flashlight around the screen, and using a piece of tape to spot remove every last bit of dust just prior to peeling the screen protector's 1st side up.
For wet applies, I find that I get better results by not using any soap, and just using water by itself. Less chance of it appearing cloudy or hazy after it dries. The key is to use liberal amounts of water to keep the protector sliding.
Every time I install one I screw it up so I finally gave up and just started picking them up at the AT&T store and let them do it. Ordered a mime ghost glass a while back and was heading down to the AT&T store to see if they would install it, but stopped at Radio Shack on the way there and those guys were more than willing to install it for me also. The guy said the mime is much easier to install because its more solid and not like those flimsy cheap ones you buy elsewhere. Seems most places that sell them aint got no problem installing them if they aint all tied up with other stuff.
Thats the problem. the cheap ones do not stick as well as the ones from good companies such as Spigen, MediaDevil, martin fields
glass protectors are the thing now, MIME feather glass from the USA is the best
Tinderbox (UK) said:
I have to have it perfect, but i always end up with dust/dirt bubbles, or it`s not aligned correctly.
I would pay to mine fitted perfect, why does somebody not set up a business fitting them.
Phone shop`s should offer the service for a small fee.
I usually buy a cheap pack or 6-10 as i throw a lot away, or still end up not having one fitted.
John.
Click to expand...
Click to collapse
I would use the hinge method for placement, as far as the dust/dirt try the shower method. Run the shower for five minutes with the door closed on hot (allows steam to form). Turn off shower and allow the steam to settle (2-3) minutes, this pulls the dust and dander out of the air. Then apply the screen protector to the handset.DO NOT leave the handset in the bathroom while the rooms fills with steam or when it is settling. I did not believe this method would work but I have used it on my Rezound, Droid X, Nexus 7 tablet and my HTC One with dust/hair free installs.
I used to be clumsy at it, but now I fit mine flawlessly. I have done it with 3 phones and 2 tablets and all of them were bubble free. My rule, keep the device under a light so you can see the dust particles or anything else clearly. Wipe it with micro fiber (or use alcohol wipes if the surface is smudgy). Use a scotch tape to remove the dust particles, small strokes, even in the areas which look clean. It takes 2 minutes to cover the whole device. Align the screen protector across the edges and work your way down, making sure the sides align and are in straight line. You will get bubbles which you can then remove using a credit card by wiping them towards the edges. Works for me everytime.
I work at a cellphone store and whenever someone buys a screen protector we install them for free glass or plastic:laugh:
what I find is the easiest method of applying a film screen protector and worked for me for 2 years whilst working in a vodafone store is the following:
1) ensure the screen is clean of dust, a good cloth in a relatively clean environment does the job, if not do it near a boiling kettle.
2) before peeling off the first layer line the screen protector up along the top of the handset, where you would like it begin. (for the htc one, it would be just below the top speaker grill),
3) peel back the first layer only slightly, line and up press down adhesive side with the top of the handset, easiest done with the top of the handset facing away from you. (benefit of this is, you've pulled the whole thing off and it's less likely to catch dust if only a small part of the protector is visible to wilderness.
4) with the top of the protector adhered to your screen, swivel the phone around so the top is closest to you without letting the protector move from it's position,
5) from here, it is a simple task of taking a piece of cardboard or hard paper and gently push forward from the top, whilst slowing peeling back the bottom plastic until you're at the bottom.
6) you may have some small bubbles right on the bottom edge of your protector, just use your thumb or the paper to gently squeeze them out.
Works for me 90% of the time. Also depends somewhat on the quality of the protector. But I would recommend a Glas.Tr or MIME type protector.
I love that dust remover that came with the mime. I covered the whole screen, ripped it off and put the glass one on in less than a second.
I bought mine from mobilefun.com. Don't remember exactly which, but it was one of the "premium" ones (not cheapest). From a 5-pack I got it perfect on the 4th try! Be patient and read the insructions carefully (which I didn't before the 3rd try) hehe ...
OK, i read no instructions apart from which tab to pull of first on the protector, i cleaned the screen with the included cloth, no steamy room or anything, it took me five attempt's to get the protector in the right place and there were bubbles galore, but i managed to get them all out, no dust underneath that i can see so i wasted no screen protectors i still have two left.
John.
Three things are recommended, dust removing sticker, microfiber cloth and a room with heated vapor such as a bathroom, after you have showered(dont take device in during shower).
I got some cheap matte ones from eBay... They are truly awsome and fit the whole screen(you must be pro master on fittin screen protectors)
http://www.ebay.com/itm/35084675949...eName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
My secret for fitting perfectly is to hold your screen down after wipin all the dust while getting the protector ready itself... Once I put it on without any dust under ir, I press it very hard and move it in direction where I need if not correctly positioned... When its just sticked on, you can still move it slighty - thats all it takes to get those 0,1mm right