Not working for me, is just stuck on the yellow triangle;(
Does anyone have any insight on this?
JD
JupiterDroid said:
Not working for me, is just stuck on the yellow triangle;(
Does anyone have any insight on this?
JD
Click to expand...
Click to collapse
what exactly are you doing?
Start every step from opening the app
Lennyuk said:
what exactly are you doing?
Start every step from opening the app
Click to expand...
Click to collapse
I open the app,
i click root my phone,
it goes rooting phone please wait, and gets stuck;( i waited for 30 minutes;(
JD
Its working now phew;P
I had to uncheck the usb debugging box and then recheck it,
i thought it was weird my phone came with usb debugging enabled, must have been an error
JD
GOOD NEWS then:
now we have CONFIRMED ROOT FOR THE DESIRE Z
[IRONIC MODE]
Unexpecteldy, the G2 root also works for the Desire Z !!
[/IRONIC MODE]
gtrab said:
GOOD NEWS then:
now we have CONFIRMED ROOT FOR THE DESIRE Z
[IRONIC MODE]
Unexpecteldy, the G2 root also works for the Desire Z !!
[/IRONIC MODE]
Click to expand...
Click to collapse
Just about to try and OC, will post my findings
JD
Visionary works fine for me. Did you set the USB to developer mode or whatever it was in the instructions?!
Go to the HOME screen and press the Menu button.
Press Settings.
Press Applications.
Press Development.
Tick USB Debugging.
Now try rebooting, then try Visionary again. Worked for me
This isn't working for me
I been at this for hours and I'm seriously getting upset. I open the app, check the boxes I'm told to check. Hit temp root and the triangle comes up and then it goes away, I'm left with a black screen for hours. I have rebooted, reset, factory reset and done every step over again and I'm still left with the same results. Why is this not working for me? It's becoming a headache.
lunchboxofomni said:
I been at this for hours and I'm seriously getting upset. I open the app, check the boxes I'm told to check. Hit temp root and the triangle comes up and then it goes away, I'm left with a black screen for hours. I have rebooted, reset, factory reset and done every step over again and I'm still left with the same results. Why is this not working for me? It's becoming a headache.
Click to expand...
Click to collapse
Seriously don't use visionary, it has a very high chance of bricking your device.
use the recommended guide here it's very safe and not too difficult.
-Nipqer
Yes, do not use Visionary, go with the gfree guide and get adb set up my friend. If u mess up, u can brick ur phone, as said from above. Well as long as u have eng hboot, u can easily unbrick, aslong as u know what commands to put in adb.
Sent from my HTC Desire Z using XDA Premium App
lunchboxofomni said:
I been at this for hours and I'm seriously getting upset. I open the app, check the boxes I'm told to check. Hit temp root and the triangle comes up and then it goes away, I'm left with a black screen for hours. I have rebooted, reset, factory reset and done every step over again and I'm still left with the same results. Why is this not working for me? It's becoming a headache.
Click to expand...
Click to collapse
DO NOT use Visionary. Its known to brick phones. Do your rooting once, do it right, with the gfree method.
Related
hello
today i tried to update my recovery image (unrevoked 2) to unrevoked 3.
I installed the hboot drivers on my windows 7 system.
Then the update process hung at flashing recovery image, but my phone rebooted and booted up. I unplugged my phone after 15 minutes and tried again.
the same thing happen and i was like .
and...
Now i dont have a recovery !! when i try to enter recovery it just brings me to fastboot!
i need help!
Did you uninstall HTC Sync?
lollylost100 said:
Did you uninstall HTC Sync?
Click to expand...
Click to collapse
no
Uninstall HTC Sync and start again. Next time read the instructions.
lollylost100 said:
Uninstall HTC Sync and start again. Next time read the instructions.
Click to expand...
Click to collapse
uninstall and install again ?
StrongOneX said:
uninstall and install again ?
Click to expand...
Click to collapse
No uninstall the program leaving just the drivers. Then run unrevoked again.
ratchetnclank said:
No uninstall the program leaving just the drivers. Then run unrevoked again.
Click to expand...
Click to collapse
Make sure you set the Boot driver also, as per the instructions in UNrevoked directory on .html file.
Also make sure you have the correct version of Unrevoked v 3.1
problem solved.
Thanks everyone !!
sooolveed...
goksar said:
how you solved that problem???i have the same thing
Click to expand...
Click to collapse
Make sure Sync is uninstalled and follow driver installation instructions.
As previously mentioned
Perhaps change your title - its very misleading, the problem wasn't unrEVOked, it was you not reading their instructions - glad you got it sorted though.
goksar said:
how you solved that problem???i have the same thing
Click to expand...
Click to collapse
i had the same issue
i backup sd card since i v only one and created a gold card
i then ran an the R5 root method since i v a version 0.8 cant remember
once u do step one dont bother about step two
just copy fake flash to ur sdcard and rename update.zip
then hold the down vol button and press power once to get to hboot
select recovery
when u get to the screen with the red triangle
press the up vol button and hold the power button
when u get to the blue screen select apply update.zip
that should take you to recovery
dont forget to backup ur stuff before u reroot
pls change title to solved
the problem was unrevoked
this happen after i tried using unrevoked
went ok from the beginning
but after the phone rebooted it kept pushing recovery for over an hour
tried it about 5 times and still did not work
as always RTFM (read the f***ing manual)
glad you got it sorted, recovery and rooting is a godsend so many roms to try haha
What about reading more to learn more?
tori007 said:
the problem was unrevoked
this happen after i tried using unrevoked
went ok from the beginning
but after the phone rebooted it kept pushing recovery for over an hour
tried it about 5 times and still did not work
Click to expand...
Click to collapse
The problem WAS NOT unrevoked, it was YOU and only YOU not reading the damn f$%&ing instructions. Before you try to root or update, please read, read and read again until you understand every single word of the instructions, and if there is something you don't understand, just ask, we are all pleased to help each other, but don't accuse a great program and the greater team behind unrEVOked.
Thanks for reading.
f.
the ginger god said:
Perhaps change your title - its very misleading, the problem wasn't unrEVOked, it was you not reading their instructions - glad you got it sorted though.
Click to expand...
Click to collapse
+1
Users never read the instructions
Hey guys, I tried to perma root my wife's G2 last night using Visionary+ r14 but when it tried to reboot it doesn't get past the green and white "HTC" screen, so now I have a couple of questions.
I bought this phone from someone off of Craigslist and it was working great until I tried to root it so it is technically out of warranty do you think I can get it replaced since everything is still stock?
Also I tried to apply the HTC OTA update to fix it and I still have the problem, is there anything I can do to repair this phone? Thanks in advance guys and mahalo!
Okay pull your battery out and put it back in..after dat press power button and volume down button until you get to the recovery screen and do a factory reset..
Sent from my HTC Vision using XDA App
Thanks for the reply jboiii15. I did a factory reset before I flashed the OTA update and I have factory reset several times but still no go. I appreciate you taking the time to help me out.
Did you try this? http://forum.xda-developers.com/showthread.php?t=842495
aznsnake666 said:
Did you try this? http://forum.xda-developers.com/showthread.php?t=842495
Click to expand...
Click to collapse
I haven't tried it because I can't get ADB to work with the phone the way it is, Fastboot works but ADB just shows nothing there while I'm in recovery or the boot screen. Thank you also for the reply. My wife is pissed lol.
Try to extract the ROM from the official RUU and rename it to PC10IMG.zip. Put this on the root of your SD card and boot into bootloader and leave it to work. This should solve your problem Fingers Crossed
JD
do you have s-off??
I don't have S-OFF as I just started the rooting procedure when it decided to take a dump on me, after this I don't think my wife will want me to root any more of her phones although I know she'll miss it after having a rooted G1 running CM and a rooted Slide running Chromatic. Good thing I didn't sell her Slide yet lol.
I'll try to find information on the PC10IMG.zip method now and see what can be done.
Thank you guys for all the help, I really appreciate it all.
itsmekeoni said:
I don't have S-OFF as I just started the rooting procedure when it decided to take a dump on me, after this I don't think my wife will want me to root any more of her phones although I know she'll miss it after having a rooted G1 running CM and a rooted Slide running Chromatic. Good thing I didn't sell her Slide yet lol.
I'll try to find information on the PC10IMG.zip method now and see what can be done.
Thank you guys for all the help, I really appreciate it all.
Click to expand...
Click to collapse
I think the rooting process has corrupted your kernel or rom, it is rare to get a brick from just the visionary process, but i know there has at least been one that this has happened to.
Report back to tell us if the extracted ROM worked for you, there is still hope;')
JD
Oh man this is just getting worse lol. I had the phone sitting here plugged into my laptop while the phone was in the Hboot screen where you can select Fastboot, Recovery and so on. All of a sudden my here Windows give off the noise as if something was connected or disconnected from my computer and I see the screen shut off on the G2 with a red light blinking. Now the phone doesn't power on and the red light blinks while the phone is plugged into the computer but doesn't power on.
As I was typing this the red light came on solid as if it is charging now, maybe it doesn't charge while in that screen and the battery just died I dunno, strange.
JupiterDroid said:
I think the rooting process has corrupted your kernel or rom, it is rare to get a brick from just the visionary process, but i know there has at least been one that this has happened to.
Report back to tell us if the extracted ROM worked for you, there is still hope;')
JD
Click to expand...
Click to collapse
Well I called T-Mobile and they are sending out a new phone, I'm unsure if I should still mess with it or not. I did flash the TMOUSA OTA update and that didn't help, I didn't unpack it to see if it contained a new Kernel but I'm sure it had a new system.img, still think it is one of those that is messed up?
I'm having a hard time finding the things to get the PC10IMG.zip going, work is calling me in different directions and my A.D.D is kicking in lol.
try this http://forum.xda-developers.com/showthread.php?t=855764 i had the same problem like you, steviewevie told me to do it, if you have problem to connect your g2 with sdk download pda net, it works for me and now i have my g2 back with the new root... just do what it said on that link believe me works...
P.D. I am a androidnoober always have a iphone and this was my first time using sdk adb or whatever name is and I did it
Thanks AndroidNoober, I've seen that link in my search for an answer to my problem. One of the issues that is making this harder is that after the phone "bricked" it lost ADB connectivity. I've tried it on two computers that have a properly working ADB (I test it with my N1 and 3G Slide) and it used to work with the G2 but now I can't get it to see the phone, I've heard Recovery has ADB blocked.
semi bricked attempting permaroot
i attempted permaroot and semi bricked my phone. will not boot past htc screen. i can't get adb to work. i am trying to get pdanet installed but it keeps getting stuck on installing on phone. can it install while phone is in recovery mode? i have had no sucess trying to figure this out on my own and phone is not covered with a warranty
i have gotten the phone to read an update.zip file.
it is reading the pc10img.zip as well.
now i just have to get past the htc screen.
i do have s-on as i had just started the process.
any help would be appreciated
Hello,
I got my Evo today and am pretty excited! I want to get this thing rooted and some CM7 nightlies going on I am familiar with android/rooting, adb, fastboot, and all that. What got me is seeing the different stuff for different evo's My Evo is as follows..
Baseband 2.158.00.11.19
Software 3.70.651.1
PRI 1.90_003
HARDWARE 0003
H Boot 2.10.0001
Its the white back...
Anyway I am looking for the correct root method, and would like clockwork recovery, if possible. Once I get that I hope it is a bit easier to find CM7 for it, lol.
Thanks in advance
http://unrevoked.com/
Fairly quick. Make sure you have the windows drivers installed [if on windows]. Also, install, then uninstall HTC sync. Once the drivers are loaded, on your phone enable usb debugging, connect to pc in CHARGE only, then run unrevoked, and put your phone down. It should reboot 2 times...taking roughly 5-8 minutes, give or take, and you'll be all set. You'll be on clockwork recovery by default, and you can upgrade to the latest recovery using rom manager.
here's a compilation of info for you. I recommend unrevoked btw
* http://androidforums.com/evo-4g-all-things-root/194918-rooting-dummies.htm
* http://www.androidpolice.com/2010/0...top-5-benefits-of-rooting-your-android-phone/ (5 Benefits of rooting)
* http://www.youtube.com/watch?v=0MrvgV2Nias&feature=related (What is root video)
This next link (first one) is where you will actually go to free your phone from the man lol. If you are going to use a Windows computer to root, there is an extra step of installing some drivers:
* http://unrevoked.com/#evo
* http://www.youtube.com/watch?v=GsoVzMadiQE (Video using unrevoked and drivers)
* http://www.youtube.com/watch?v=iXWm8262iMU&feature=player_embedded (Another video using unrevoked)
Drivers link and instruction info for windows:
* http://unrevoked.com/rootwiki/doku.php/public/windows_hboot_driver_install (FYI, the drivers link is near the top of the page in the link)
* http://www.youtube.com/watch?v=FXDszE0Ytn8 (How to install HBoot drivers)
Good luck!!
Thanks for the fast responses! I am downloading the HTC sync, kinda slow server on their end. I have the H Boot drivers installed and ready to go. Let me get this straight, in charge only mode I run "reflash package" from my PC (windows 7).
Thanks
cordell12 said:
Thanks for the fast responses! I am downloading the HTC sync, kinda slow server on their end. I have the H Boot drivers installed and ready to go. Let me get this straight, in charge only mode I run "reflash package" from my PC (windows 7).
Thanks
Click to expand...
Click to collapse
Correct. Just make sure usb debugging is also enabled, found in settings> applications > development.
It has rebooted twice now, but the app gives me a error...
Internal error: Uninstalling Package Failed
Recovery Image: Clockworkmod Recovery
Do I leave it sit, or rerun it? Or is it done?
installed super user and titanium back up count not get root
cordell12 said:
It has rebooted twice now, but the app gives me a error...
Internal error: Uninstalling Package Failed
Recovery Image: Clockworkmod Recovery
Do I leave it sit, or rerun it? Or is it done?
Click to expand...
Click to collapse
The app [rom manager] or unrevoked is giving you an error?
teh roxxorz said:
The app [rom manager] or unrevoked is giving you an error?
Click to expand...
Click to collapse
sry unrevoked
cordell12 said:
sry unrevoked
Click to expand...
Click to collapse
Disconnect the phone from the pc. Boot into the bootloader by turning your phone off, then holding vol+down as is turns on. The select recovery. Also tell me if it says S-OFF at the top. If you get the red triangle, you're rooted, but no recovery and I can give you the clockwork recovery.
Edit: This was my 666th post. Its special because each of my names [first, middle, last] all have 6 letters, = 666.
teh roxxorz said:
Disconnect the phone from the pc. Boot into the bootloader by turning your phone off, then holding vol+down as is turns on. The select recovery. Also tell me if it says S-OFF at the top. If you get the red triangle, you're rooted, but no recovery and I can give you the clockwork recovery.
Edit: This was my 666th post. Its special because each of my names [first, middle, last] all have 6 letters, = 666.
Click to expand...
Click to collapse
I have a phone with a little triangle (red) on top right, with ! in the middle of it.
LOL @ 666 post!
cordell12 said:
I have a phone with a little triangle (red) on top right, with ! in the middle of it.
LOL @ 666 post!
Click to expand...
Click to collapse
Can you get into the bootloader screen?
teh roxxorz said:
Can you get into the bootloader screen?
Click to expand...
Click to collapse
The white screen , yes from there I chose recovery, and thats when I see the phone with triangle. Was I to run this from H Boot (white screen)? I ran from home...
Okay you scared me. Put that on your sdcard, boot into bootloader, and when it asks to update, select yes, the reboot phone and you'll be set.
teh roxxorz said:
Okay you scared me. Put that on your sdcard, boot into bootloader, and when it asks to update, select yes, the reboot phone and you'll be set.
Click to expand...
Click to collapse
It asked me to update, I volume up for yes, then I did the same for reboot. I am rebooted now, and still now root titanium still says no root...
I am on windows 7, should i change compatibility to XP and rerun UnRevoked?
getting a bit worried, lol. Phone is 2 hours old
Okay good. Now re-run unrevoked.
teh roxxorz said:
Okay good. Now re-run unrevoked.
Click to expand...
Click to collapse
On the phone Zysploit is force closing...
Now unrevoked app is saying FAIL is my firmware to new?
Also, its possible to have a bad flash [it happens to other users] so no need to worry. You're in good hands.
cordell12 said:
On the phone Zysploit is force closing...
Now unrevoked app is saying FAIL is my firmware to new?
Click to expand...
Click to collapse
What is Zysploit?
teh roxxorz said:
What is Zysploit?
Click to expand...
Click to collapse
I have no clue, must be something to do with the unrevoked, because as soon as I clicked force close the unrevoked app popped up the error message..
Well basically re-run the whole process from the begging, the unrevoked on the comp I mean.
Please help! I've been trying to find answers and trying to fix my G2 this whole week and, to even add how much im working/reading on how trying to fix it, i even stayed up a WHOLE night reading about things but still no-go
G2 is semi-bricked because my brother was going to permanently root the G2 and right when the process finished, is when the phone was semi-bricked because he "forgot" a step (great -_- human error)
Just a few things:
Yeah i can go into recovery (VOL down + Power Button) but, im a noob at recovery things, so i dont know how or what to use or do like i said, i've researched a lot and done the steps that i read online and still nothing, so i rather get answers/help from great people in here (i heard this forum is really smart/good at Android stuff)
please help!
XvideogamerX said:
Please help! I've been trying to find answers and trying to fix my G2 this whole week and, to even add how much im working/reading on how trying to fix it, i even stayed up a WHOLE night reading about things but still no-go
G2 is semi-bricked because my brother was going to permanently root the G2 and right when the process finished, is when the phone was semi-bricked because he "forgot" a step (great -_- human error)
Just a few things:
Yeah i can go into recovery (VOL down + Power Button) but, im a noob at recovery things, so i dont know how or what to use or do like i said, i've researched a lot and done the steps that i read online and still nothing, so i rather get answers/help from great people in here (i heard this forum is really smart/good at Android stuff)
please help!
Click to expand...
Click to collapse
explain your semi bricked status... how do you know its semi bricked? which step did he miss?
also you be better off asking in guide how to recover semi bricked phone rather than asking in Q & A....experienced mods usually follow that thread and reply to ppl who have queries
it wont go into the Android OS, it just stays stuck at HTC. No further. And he didnt tell me, but he watched a video on youtube.
and ohhh darn -_- stupid me
XvideogamerX said:
it wont go into the Android OS, it just stays stuck at HTC. No further. And he didnt tell me, but he watched a video on youtube.
and ohhh darn -_- stupid me
Click to expand...
Click to collapse
here is the link to the desire z /G2 wiki...
http://forum.xda-developers.com/wiki/index.php?title=HTC_Vision
go straight to the rooting section and try to find out which method was he using to root your phone... when you narrow that down try to find which step he missed.....when all thats done than either post here exactly which method was he using and which step he missed.....or post in the semi bricked page.....
right now the most current recommended method is using Gfree...
also try to see if you have access to your recovery and if clockworkmod recovery is installed or not....
for that take out your battery and put it back in.... hold volume down and power button....
it will boot into boot loader
give it few seconds to display that "waiting for SD card Pb10.img not found"
than use volume down button to navigate to recovery and use power button as click selection..... if it boots up into clockworkmod recovery than you have custom recovery installed
Yeah i dont have CWM installed, just checked. And what my brother told me is that he was "temporary rooted" then he tried to "perm root", but actually, he didnt go to youtube, he tried to perm root using the VISIONary method.
XvideogamerX said:
Yeah i dont have CWM installed, just checked. And what my brother told me is that he was "temporary rooted" then he tried to "perm root", but actually, he didnt go to youtube, he tried to perm root using the VISIONary method.
Click to expand...
Click to collapse
check wiki for htc vision ... for how to fix errors during rooting.....
also if you wanna root gfree is recommended software lately..... check wiki to confirm.....
also try factory reset.... by turning phone off... than holding power button and volume up and down button .... i think.....confirm via wiki
Well i also cant do any adb steps because adb doesnt detect my G2 (although it detects it when im in recovery (the menu with a phone and red exclamation point) but it says its offline) i can only use fastboot
and btw my G2 is S-ON
and i have done factory resets and nothing
I'm not as experianced as a lot of the but have you tryed the pc10img via fast boot? That might work scince everything is stock on your phone
/edit have you gone the the adb guides it took me a few times but I finally got it...adb looks the best way to go
Sent from my T-Mobile G2 using XDA Premium App
yeah but when i use PC10IMG it just says main version is older (or something like that) and says update failed.
and yeah i have seen tons of ADB guides, but still doesnt work what guide did you use? how'd you do it?
XvideogamerX said:
yeah but when i use PC10IMG it just says main version is older (or something like that) and says update failed.
and yeah i have seen tons of ADB guides, but still doesnt work what guide did you use? how'd you do it?
Click to expand...
Click to collapse
it might be because you tried the 1.12 verison pc10img.zip and your phone came with updated 1.19 version
PC10IMG_Vision_TMOUS_1.19.531.1_Radio_12.21.60.09b _26.02.01.15_M2_release_149459_signed.zip
try this one by putting in your sd card. your phone should flash it and it shouldnt say version is older...
download from here
http://shipped-roms.com/index.php?category=android&model=Vision
when you put it in sd card rename it to just PC10img.zip and reboot into bootloader and when it asks you to flash. let it flash
I'll try that right now, but I think I did use the 1.19 one but can't recall.
I'll edit this post to tell you if it works
EDIT:It still says Main Version is Older...you think i need to use the 1.12 one?
BTW here is my G2 info (radio version etc.)
VISION PVT SHIP S-ON
HBOOT-0.82.0000
MICROP-0425
RADIO-26.03.02.26_M
eMMC-boot
Sep 2 2010, 17:59:38
I'm on my phone so I canot link but under the stickies you will see a thread about un rooting your phone now you will need to do the hex editing step and replace it then try the pc10img and see if that will work
Sent from my T-Mobile G2 using XDA Premium App
This is a link to the latest update for Tmobile G2. Give this a try and see if it works for you.
http://android.clients.google.com/p...US_1.22.531.8-1.1.19.531.1_release_signed.zip
# Rename the file to “update.zip” (If you don’t see the file extension, assume it’s already in zip format and just name the file ‘update’)
# Transfer the file to the root of the SD card (in no folder)
# Turn G2 off.
# Turn G2 on by holding power and holding volume down. Once it boots, you’ll be given a white screen with Androids skateboarding. Wait for the green text to flash on the screen, and then by using your volume up and down keys, go to recovery and press the power button,
# The phone will reboot itself into recovery, and you will see a black screen with a phone and a red triangle with an exclamation mark in the middle. We need to see the text in the recovery, so at the same time press the power button and volume up. It may take a few tries.
# Once the text appears, using the volume rocker, navigate to Apply sdcard:update.zip
# Let it install and reboot your phone.
EdKeys said:
This is a link to the latest update for Tmobile G2. Give this a try and see if it works for you.
http://android.clients.google.com/p...US_1.22.531.8-1.1.19.531.1_release_signed.zip
# Rename the file to “update.zip” (If you don’t see the file extension, assume it’s already in zip format and just name the file ‘update’)
# Transfer the file to the root of the SD card (in no folder)
# Turn G2 off.
# Turn G2 on by holding power and holding volume down. Once it boots, you’ll be given a white screen with Androids skateboarding. Wait for the green text to flash on the screen, and then by using your volume up and down keys, go to recovery and press the power button,
# The phone will reboot itself into recovery, and you will see a black screen with a phone and a red triangle with an exclamation mark in the middle. We need to see the text in the recovery, so at the same time press the power button and volume up. It may take a few tries.
# Once the text appears, using the volume rocker, navigate to Apply sdcard:update.zip
# Let it install and reboot your phone.
Click to expand...
Click to collapse
Alright ill try this as well, and tell you if it works
EDIT: yeah i updated it, and it worked fine, but im still stuck on the HTC logo
dakkywantstodocrazysht said:
I'm on my phone so I canot link but under the stickies you will see a thread about un rooting your phone now you will need to do the hex editing step and replace it then try the pc10img and see if that will work
Click to expand...
Click to collapse
ill try that if the method on top of your quote doesnt work
thank you both for helping,ill thank your guys post
EDIT: i read the guide (at least i think its the one your talking about, there are a ton of guides out there of how to unroot) and it says i need to get the misc.img from my phone....i cant because i cant adb since it doesnt detect my phone (but fastboot does)
XvideogamerX said:
Alright ill try this as well, and tell you if it works
EDIT: yeah i updated it, and it worked fine, but im still stuck on the HTC logo
Click to expand...
Click to collapse
Sorry that didn't work for you. Here's another method and zip you can try...its worked for some others:
http://forum.xda-developers.com/showpost.php?p=10583834&postcount=33
Alright ill try that out thanks
EDIT:Hmm...thats strange. Right after it checks the PC10IMG.zip ,it doesnt tell me anything else, it just goes back to the recovery menu (where it shows Fastboot, Recovery, Factory Reset etc.) shouldnt it say if i wanted to update?
Well I think it loads the pc10 and then auto does it it might ask first tho I'm not sure...there have been issues with windows 7abd what os are you running?
XvideogamerX said:
Alright ill try that out thanks
EDIT:Hmm...thats strange. Right after it checks the PC10IMG.zip ,it doesnt tell me anything else, it just goes back to the recovery menu (where it shows Fastboot, Recovery, Factory Reset etc.) shouldnt it say if i wanted to update?
Click to expand...
Click to collapse
Sent from my HTC Vision using XDA App
dakkywantstodocrazysht said:
Well I think it loads the pc10 and then auto does it it might ask first tho I'm not sure...there have been issues with windows 7abd what os are you running?
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Windows 7, and i read about that too -_-
and auto does it? like it automaticly flashes it??
Yeah it automaticaly might..are you running 32 or 64 bit os?
XvideogamerX said:
Windows 7, and i read about that too -_-
and auto does it? like it automaticly flashes it??
Click to expand...
Click to collapse
Sent from my HTC Vision using XDA App
dakkywantstodocrazysht said:
Yeah it automaticaly might..are you running 32 or 64 bit os?
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
How would I know that? No conformation message or anything comes up :/ and 64-bit (which I read is the one that has the most problems)
hi im in extreme trouble. i used visionary to temproot my desire z/G2 and was trying the unlockr method so i kept on on temp root on every boot. now my phone is not working. whenever i boot, i get the lockscreen and when i slide it, i only get visionary app and black screen and after a while it shows visionary has stopped responding and asks to force close or wait. i dont know what to do i cant use my phone and ive tried taking out battery and booting 4 times.
Well, I have bad news and good news... The bad news is that I myself cannot help you with this problem because I do not have enough knowledge on the rooting subject. However, the good news is, I do have enough knowledge to tell you that you are NOT screwed, for you are not bricked! I would highly suggest following a different guide for rooting however, for example the one found here: http://forum.xda-developers.com/wik...sion#Rooting_the_Vision_.28G2.2FDZ.29_and_DHD
I used it and it worked perfectly. Also visionary is known to have a high chance of bricking your phone (I throw this in just in case, bricking makes it unusable)
What you can probably do is factory reset your phone and then follow the wiki guide to achieve root, though I would wait for one more person to confirm that this is advisable as again I am not the most knowledgeable on the subject.
Best of luck!
PS I'm pretty sure that factory reset and following instructions is the way to go but I don't wanna be responsible for a bricked phone It's what I would do though
yasirrfc said:
hi im in extreme trouble. i used visionary to temproot my desire z/G2 and was trying the unlockr method so i kept on on temp root on every boot. now my phone is not working. whenever i boot, i get the lockscreen and when i slide it, i only get visionary app and black screen and after a while it shows visionary has stopped responding and asks to force close or wait. i dont know what to do i cant use my phone and ive tried taking out battery and booting 4 times.
Click to expand...
Click to collapse
You're not bricked for sure You can use the guides here on my blog www.desirez.strawmetal.com to root your phone(it works)..Do the entire process again...
Dont feel scared to use ADB.. its not complicated once you start using it...
NEVER use VISIONARY!! I almost bricked mine too... hope my guide works for you..
hyey thanks a lot for your advice but now something new happened. my phone was fine and uninstalled visionary. now i used the other root method and now my phone is bricked i think. it is stuck on white screen with htc logo and i tried to reboot again and again. also my mem card doesnt have any rom image right now so i cant do any thing. please helllp
You can try this.. Use an sd card reader and copy your rom onto the sdcard root.. See if it works
Sent from my Desire Z