USB tether under Mac OSX - help needed - Desire Q&A, Help & Troubleshooting

Hi everybody!
i've just updated my desire to 2.2, and i've some issues with tethering with my mac.
under 2.1 I got it working using bluetooth DUN under mac, and using pdanet on the desire.
I've read that 2.2 support usb tethering, and I've activated it on the phone, the mac does recognize the "android phone" but even if i fill the required field in the advanced property panel (that is: "general" device, "tre.it" as APN), the mac refuses to connect to the phone. Phone number was either left blank or set to *99#.
I've tried as well the new wifi hot spot and that's working flawlessly.
Bluetooth DUN doesn't work anymore with 2.2 and pdanet, something must have changed in the firmware perhaps?
but please, somebody had managed the usb tether to work?

anyone?

Related

[Q] Help!! Defy CM7 USB Tether ~

Hi there, I am using CM7 RC1v2 on my motorola defy. I am facing a problem which whenever i connect my phone to windows using phone portal the usb tether cnt be checked. But when i connect using "charge only" the things become available again but i still could not connect. Anybody face this problem and can help me to solve it? Thx very much!
Phone portal run on specific IP number and it uses different port and this explain why USB tether won't run.
I'm using it and here's my steps.
AFAIK, the pc required the USB tether driver for it to run properly. It should automatic install of the required driver. Once the driver is installed, you could perform a few steps here. I'm using Windows 7
1) Goto Control Panel - Network and Sharing Center - Change Adaptor settings.
2) Disable any active Local Area Connection if there are any of them running
3) Enable the one USB tether(it might already enabled by default but you could double check it).
4) It will auto verifying and connect once it done verified.
5) Start your internet browser and enjoy(you may need to do: Internet Option - Connections - Lan Settings - Unchecked proxy server .
farsight73 said:
Phone portal run on specific IP number and it uses different port and this explain why USB tether won't run.
I'm using it and here's my steps.
AFAIK, the pc required the USB tether driver for it to run properly. It should automatic install of the required driver. Once the driver is installed, you could perform a few steps here. I'm using Windows 7
1) Goto Control Panel - Network and Sharing Center - Change Adaptor settings.
2) Disable any active Local Area Connection if there are any of them running
3) Enable the one USB tether(it might already enabled by default but you could double check it).
4) It will auto verifying and connect once it done verified.
5) Start your internet browser and enjoy(you may need to do: Internet Option - Connections - Lan Settings - Unchecked proxy server .
Click to expand...
Click to collapse
I have tried following ur steps but it still can't work. My pc was able to install all the driver except that when installing MTP USB driver, it failed.

[Q] Wifi tether won't work, rooted KF and Evo 4G

I've searched several threads, but can't figure out what I'm doing wrong.
Both devices definitely 100% rooted with superuser working fine, permissions granted for all apps.
I installed wifi_tether_v3_1-beta14.apk on the phone.
Device Profile: Evo 4G
Setup-Method: Initially I tried Softap (master). That's the same as infrastructure mode, correct?
Default SSID (AndroidTether)
MSS Clamping checked
Routing Fix checked
If I attempt to run it with these settings, I get a popup informing me the wifi hotspot started, but with errors. The log just says most of the wifi steps failed, I can post details if needed. I don't think it's really running - no upload/download indicator showing at the bottom of the app. My PC can't see the hotspot.
If I switch Setup-Method to Ad-hoc, it runs fine, no errors, PC can see it and connect to it. But KF can't connect to Ad-hoc... so lame.
So, I got ZT-180 Adhoc Switcher.apk for the kindle fire, to switch it to ad-hoc mode. Went to settings, told it to connect to AndroidTether. Switched to Ad-Hoc mode. It says "attempting to connect" ... after a minute it gives up and keeps retrying. The hotspot shows in the list of wifi networks, but it's hanging at "Obtaining IP address".
So, what's the issue? Infrastructure mode not working? Need to flash a custom rom? I read something about maybe needing a non-stock kernel? Upgrade or downgrade my radio?
I finally found a method that works, barely.
Wifi Tether (app listed above) failed.
Adhoc Switcher failed.
Wifi Hotspot Widget failed.
Elixir2's hotspot widget failed (connected but no surf).
The one that worked is free and doesn't even need root apparently: Foxfi.
I say it "barely" worked because even this has issues.
When I tried to create a password, it wouldn't connect.
But if I leave the password blank (no password) it does work.
http://foxfi.com/bin/
I just told it to start running, and left the SSID at the default (FoxFi98 I believe).

[Q] defy+ 2.3.6 usb tethering not working

I cannot use USB tethering on my Motorola Defy plus, 2.3.6 not rooted.
I use a linux(ubuntu 12.04) host configured with wicd.
I have acces to the enable USB tethering option in Wireless&networks
I can access internet from the phone.
I receive an valid IP on the linux comp. routes are added, I can eaven ping the phone ip from computerand the computer from the phone.
BUT it look like the phone does not do the routing correctly because I cannot acces anything in the internet (all traffic from comp is routed to the phone and just dies there).
I tried it with both enabled and disabled USB debug.
With other android phones (same operator) it works with no changes on the linux box and exactly the same steps.
Are there any chances to make this work?

[Q] I9195 - Unable to connect to WIFI network (Authentication error occurred);

So, here it goes.
My goal is to connect to a network using certain MAC address. Wanted network is marked with "open" and I know that it allows access only to certain devices (according to MAC) on which the administrator have gave a permission to. Once your MAC passes the verification, device gets connected to the network and then I'm asked to enter username and password through WEB browser (well known for me, because it is a procedure that I do on my other device, as well as all my colleagues do).
For example, I was allowed to provide one personal MAC address to administrator to connect to this network. I would like to set the MAC address of my other personal device and set it on my I9195 so that I can access the same network.
So, what have I done so far: I9195 is rooted, it has Android 4.2.2 on it and Busybox installed. I have changed MAC on it using following apps: MacChanger (blue WIFI logo), MAC Address Ghost (green ghost logo), using Android Terminal Emulator commands and via MAC Spoofer (black circle with green text logo). What can I conclude: As soon as superuser has granted the access to these apps, all of them manage to change the MAC. I've done the verification using Terminal Emulator. I also have to add that the MAC remains original if viewed from WIFI advanced menu BUT this shouldn't be an issue because:
1.) Colleague of mine is using his S4 (rooted etc.), while using MAC Address Ghost that does not change the original address (viewed from WIFI advanced menu) but he manages to make a spoof (verified from the Android Terminal Emulator, as all of this apps actually do) and he manages to connect without any problems in the same way as I connect with another device that I have!
2.) I had time to make a small test at home which put a light on the idea that the problem should be focused on the Samsung (and not on the router, especially because I am unable to modify anything on the router on this facility, not even restarting it). My home network works in a similar way as the network that we are discussing about. My S4 Mini has been included in it with his original MAC and it connects to the network without any problems. My other device is also included to the network using its MAC (the one that I am using for spoofing). My other device is turned OFF, router has been reset and I am normally accessing the network with S4 Mini. Then I run the MAC Address Ghost to spoof the MAC on my S4 Mini. In that moment, I have lost the connection that I had which means that the MAC spoofer actually did something. I tried to reconnect to the network but then I am asked to enter the password for my network. I have checked and re-checked it many times, tried to forget the network and doing it all over again but it does not accept the CORRECT password. Changing my MAC back to the original one connects S4 Mini back to the network, while accepting the password immediately.
Problem is represented in a way that it either says “saved” and does not connect to the network or every few times displays a message “Authentication error occurred”.
I have tried I would say every possibility that I’ve seen over the internet. That includes:
1.) Installing WiFi Connection Manager (it provided some info regarding the network that I wish to connect to: IEEE 802.11g standard, 54 Mb link and CH:11). I’ve used its function to fix the WIFI (advanced fix (root required)) but it didn’t help.
2.) All sorts of staying close to the rooter, while enabling and disabling the Power save mode (accessed via *#0011# command) or while having GSM signal.
3.) Browsing through system, data etc. folders to try to find the file that contains the MAC address information (like it did on older android versions in the nvram file). I’ve been unable to find this file or any sort of file that displays my MAC for the purpose to modify it.
I have a plan to upgrade Android to version 4.4.2 later today and make a test.
Please, feel free to suggest anything else! If I do not succeed, I will have to replace my S4 Mini with something else.
Kind regards,
QUICK REPLY: After installing CyanoGEN MOD 4.4.2, the problem remains!
I think there could be a shorter solution! On Sony Xperia Acro S with 4.1.2 Android it was just a matter of changing the MAC address within the file data/etc/wifi/fw! One minute modification...
So, please, if somebody knows the path to the file that contains MAC on CyanoGEN MOD 4.4.2 or on Android 4.2.2, PLEASE HELP!
Kind regards!

[Q] Internet passthrough / reverse tethering with P6, not rooted

Hi.
I'm looking for ways to reverse tethering with P6 non rooted. I found the link below, but I'm having difficulty in running the program. Can anyone help me, what should I put in the settings of the program? I'm also running AdBlock Plus for Android, whihc calls for local proxy 'localhost' and port 2020.
http://www.goandroid.co.in/how-to-reverse-tethering/29720/
zemega said:
Hi.
I'm looking for ways to reverse tethering with P6 non rooted. I found the link below, but I'm having difficulty in running the program. Can anyone help me, what should I put in the settings of the program? I'm also running AdBlock Plus for Android, whihc calls for local proxy 'localhost' and port 2020.
http://www.goandroid.co.in/how-to-reverse-tethering/29720/
Click to expand...
Click to collapse
Connectify works well for me over wi-fi, as I understand, you are trying to reverse-tether over usb? port 2020 is not a problem since you will be using 8090 and 8080. You need to have an active and working adb (enable adb on your device and connect it to the pc, open cmd and run [adb devices], see if it turns up or not. If it does then it should not be a problem getting this to work according to the guide.

Categories

Resources