Develop Bugs

Invisible Gadget Guard Screen Protector - Review

Review of the Invisible Gadget Guard | Screen Protector Shield for HTC Aria
Better then the one from at&t...
Size
...still just a little too big. The need to take a millimeter off the top. Also, the hole for the track button is a little to big... or I could have just stretched it while applying, but I'll get to that. Otherwise I am happy with the fit of the protector.
Application
Be afraid. If placing a near dripping wet "vinyl" sheet on your phone doesn't sound like a good idea, then this protector is not for you. This application method dose provide with a wide margin of error, if your like me and fail at applying screen protectors 50% of the time. The downside to this is as the protector will bend and wrinkle making smooth application difficult. Application tip: take the back off your aria and place the phone on a washcloth. That will allow the water that is forced out to run away from the phone and be caught by the washcloth.
Look
After application your display will appear off for a few min, but as the water evaporates, that will go away. The next day the display will be fairly clear, and not much worse then the hard plastic sticker screen protector. In my case the protector was not quite smooth, but that could be my 5 failed application attempts. While this is slightly annoying, is not a major issue.
Overall
This is not a bad screen protector, but has quirks that you may not like. It is better then the default at&t protector, but as new "hard" protectors come on the market, it will fall to you confidence and personal likes and dislikes as to if you choose this protector.

I tried this and totally ruined it. It looked like crap when it was on, with lots of gray areas, and the bubbles wouldn't all come out.
I tossed it in the trash and just chocked it up to more money wasted, because I read on the web that they will fight you tooth and nail if you try to get a refund.

When I did it I had that problem, but I pulled it off before it stuck, added more water and tried again. It really did take like 5 tries to more or less correctly apply the stupid thing.

Just installed mine. It seems a bit cloudy. I didn't think application was difficult, but the necessary use of water is unnerving. Hopefully it clears up as it dries.
Sent from my HTC Aria using XDA App

Just got mine in the mail and applied it today. A bit difficult but it's pretty good. Just got that cloudiness like others have mentioned. I'm guessing these are fine,tiny bubbles. I read in a few places the cloudiness will take sometime to dry up (about a week to cure completely). Apparently this material is tough stuff and if the cloudiness disappears, it'll all be worth it xD

Hope it clears up. Keep us posted. Still trying to decide which screen protector to buy.

Great review. You almost have to install these things in a clean room with robotic surgical devices to get them perfect.
I ended up going to bestbuy the other day and getting a zagg for an incredible. It was just a smidge bigger but came out damn near perfect. It is almost the exact size in width and the speaker is perfect, but the bottom is just about a 1/2 too long, so I had to trim and use a hole punch. Super disappointed in zag for not releasing the right cover. Jessica from zagg tells me that they have a cover the they are not releasing it yet and have no release date in sight. grrrrrr. I know the hd mini zagg is supposed be a good fit to, but bb did not stock that cover.

A few days on, and the cloudiness persists...anyone seeing any improvement?
Sent from my HTC Aria using XDA App

stickbo said:
Super disappointed in zag for not releasing the right cover. Jessica from zagg tells me that they have a cover the they are not releasing it yet and have no release date in sight. grrrrrr. I know the hd mini zagg is supposed be a good fit to, but bb did not stock that cover.
Click to expand...
Click to collapse
That's interesting, given that it's on their web site and I didn't see anything that said it was not yet available. Of course, they might tell you that AFTER they take your money. But I could just be cynical.
Post Script: I've got the Invisible Gadget Guard, and it's ok. What's perfectly applied is fantastic. But there are some places where it looks like there are small air bubbles underneath. Reapplying simply changed the pattern. They were originally annoying but, 2 days later, are decidedly less so. However, positioning is a pain.

stickbo said:
Jessica from zagg tells me that they have a cover the they are not releasing it yet and have no release date in sight. grrrrrr. I know the hd mini zagg is supposed be a good fit to, but bb did not stock that cover.
Click to expand...
Click to collapse
Apparently Jessica from Zagg is a dirty liar.
http://www.zagg.com/invisibleshield/htc-aria-cases-screen-protectors-covers-skins-shields.php

A quick check in here.
I purchased mine on Ebay from a seller called jusage. I paid a cool $7.67 for the Invisible Gadget Guard film PLUS car charger (generic 12v cigarette lighter adapter to micro-USB), and FREE shipping. A pretty good deal, in my view.
Unlike Zagg's, the kit includes neither a vial of "Apple sauce", nor a swath of chamois, not a squeegee. But I installed Zagg's films many time before and am quite comfortable with just a sauce of water (with one 1 tiny drop of dishsoap), a credit card, and a microfiber towel.
The fit is ideal. All cutouts are perfect. The film went on without any issues. After having dried overnight, the film is invisible now.

Same here I got the Gadget guard from ebay with the charger.. Only took 5 mins and let it dry good to go. And the charger is not a to much of a POS!!

cranked said:
A few days on, and the cloudiness persists...anyone seeing any improvement?
Click to expand...
Click to collapse
9 days since I first installed, and all the cloudiness is gone...in fact, I had forgotten about it all week, and actually thought of it this morning and had to look for edges to see if it was even on there! Patience is key, but I have to say after a week, you can't even tell I have it on there.
Fit = perfect, no bubbles, no cloudiness...
Definitely giving the Gadget Guard 5 stars...highly recommend.

cranked said:
9 days since I first installed, and all the cloudiness is gone...in fact, I had forgotten about it all week, and actually thought of it this morning and had to look for edges to see if it was even on there! Patience is key, but I have to say after a week, you can't even tell I have it on there.
Fit = perfect, no bubbles, no cloudiness...
Definitely giving the Gadget Guard 5 stars...highly recommend.
Click to expand...
Click to collapse
Ditto. I put mine on about a week ago. Application was easy. It is certainly not "invisible" as I can still tell it's there. The cloudiness is gone, it did take a while. There are no air bubbles like you would see with cheap protectors. It was easy to install, I ordered it from amazon and paid a few bucks more than most people, but I'm happy with it. Now, if only my amzer argyle case would ship...

I put the invisible gadget guard on about a week ago, I wouldn't say I'm having issues with cloudiness, as much as little pin sized dots all over the place, in clumps (which could be the so called "cloudiness"). its definitely not air bubbles as air bubbles would be bigger. Its causing a little pixel distortion on a plain white screen.
As I said, it has been almost a week and no real improvement.could anyone tell me if this is the same issue they are having or had? Or when these god forsaken dots will go away?!?
This was the first experience I've ever had with invisible gadget guard. I have however, applied three invisible shields (on other devices) with no such issue.
Thanks in advance for any input!
Sent from my HTC Liberty using XDA App (with swype, which is freaking AMAZING!) LOL

Overall I like it. Cloudiness disappeared but there's like two specks of dust under the guard. Just as long as it does the job, I'm not complaining.
Got the free car charger too. Hehe

I also purchased the Aria protector combo (screen + back + car charger) from jusage on eBay. Best-offered him $12 shipped which he promptly accepted. I ordered it the same day I ordered my phone from AT&T, hoping it would arrive at the same time or before the phone did. The phone arrive first, 2 days before the Gadget Guard.
Having read and viewed the installation instructions and video online (I was also sketchy about the water application), I decided to keep my phone untouched in the box until the protectors arrived. When they did, I washed my hands thoroughly before opening the box and removing the plastic from the phone. I washed my hands again before beginning the install of the protectors.
The fit of the film for the screen is dead-on. The fit for the back is okay, with cut-outs for the camera and htc logo. Make no mistake, due to the rubberized material, it's tricky to install the back film. I decided not to use water on the back (did on the screen though) because I wasn't sure the rubber wouldn't absorb the water or allow it to dry once the film was applied. I was meticulous with the application, using a credit card to slowly ease on the film from top to bottom before using a microfiber cloth (microfiber = no lint) to wrap the edges. When all was said and done, it looked pretty good. I had to peel back and re-install one edge of the screen to get rid of a pesky air bubble, but the back was pretty solid on my first try.
The next day, one of the top edges was peeling back. I pressed it back down and it re-adhered itself, but about 20 minutes later, it began peeling again...just enough to catch some lint. I tried 3 more times to clean it with water and reapply, but each time it would peel up. Finally I decided to just cut it off.
Today, two days later, the opposite corner started to peel up.
I emailed jusage through eBay and explained the situation to him. He replied the same day, apologizing for the trouble and saying he was sending me a replacement back film at no cost.
I'll update when I've received the replacement back film, but overall, I like this product. You can't beat the combo deal of a front and back protector film AND a car charger, all for $12 or less shipped to your door.

Electrostatic vs. Adhesive Screen Protectors

Hello All,
I know that I want a PET or other glass-like screen protector. Generally speaking, I never used screen protectors because they never really held up all that well and on top of that they never had the feel or look of the real thing. Now I have a scratch on my screen that is not normally visible, but I know its there.
I have run into a debacle because I know that while I am good at putting on screen protectors, I am no expert and the PET ones are harder to get perfect than the rubbery ones (which I now despise). So, recently I have seen that there are some PET/Silicone/ Electrostaic Hybrid screen protetctors and then there are still the PET with Adhesive.
Does anyone have experience with the electrostatic type and how good are they at staying on and bubbles?

I have no idea what is PET, or the different types. However, if you are talking about the one I got:
http://www.handhelditems.com/crystal-clear-screen-protector-p-135710.html
my experience is that this has great clarity, can get bubbles during applications, and they rarely come off by itself. On the many devices I've used this type of protector on, only one came off. It started in one corner, and over the course of a month with gradual lint build up the screen protector eventually got ruined. I could've washed it and reapplied for that month, but I had a spare so I was lazy. You can reapply the protectors as needed to get the application right. The bubbles that occur aren't the same as the rubbery kind. Air bubbles can easily be pushed out after application. The problem is dust that prevent the protector from adhering to screen, causing a little bubble. If the dust is really small, the bubble goes away over a day. Or, like me, you can live with it. You try getting something the size of an iPad dust free.

Bought Electrostatic - LOVE THESE!
Ok, as a preface I have owned and used screen protectors before.
I had an iPhone before the EVO and used the Griffin Ultraclear hard Protetctors ad the PowerSupportUSA products of every variety on my previous iPod products (iPod Mini 1G, 4G, Nano 1G, 5G, Shuffle 1G, Touch, iPhone) not to mention an invisible shield one or two. I gave up on the films towards the end of my Touch ownership. They always felt horrible and I could never get one absolutely perfect (didn't help that they usually were not perfectly cut).
For the Evo, I tried the InvisibleShield the first day because I remembered just how well the InvisibileShield had held up on my 5G. Well I think that they have changed the formula, or rather that 3M has since then because the smooth feel and smooth look of the original are most definitely gone. The new variety is rubbery (even after days of use) and is not cut well enough to be a perfect fit (it never covered edge to edge). So i skipped it. Well it seems that with this large of a glass screen, you are much more liable to getting scratches (versus using and unprotetcted iPhone/Touch screen) and I got a few ultra hairline ones that are barely if ever visible to the naked eye and just knowing that they are there bothered me. So I needed to think of getting a screen protector.
Seeing as how air moves and its nearly impossible to get a screen protectors on without any bit of dust, I decided on getting the electrostatic variety so that I could rinse if it came off or needed to be reapplied.
I bought These: Electrostatic Screen Protector - Clear Hard
- Hard variety (PET)
- Very Clear
- Silicone Layer (helps the scratches and dents heal themselves and give sturdiness to the PET)
- Electrostatic layer (holds the screen protector onto the phone)
Six pack delivered for $4? I could do much worse.
Well as it turns out, they are PERFECTLY cut and cover every inch of screen and no more. It went on smooth as butter and I got no bubbles or dust or fingerprints or anything (used a credit card to smooth it down). These were by far the easiest I have had. Not only that, but the electrostatic holds on just as strong as the sticky variety and will not get the gunk on the sides sticking to it! I have taken my TPU case on and off a bunch and had no lift whatsoever. As a bonus, THEY SHOW FINGERPRINTS MUCH LESS THAN THE GLASS SCREEN DOES!
So at $0.65 each, they are killer and having a few backups is nice as well as giving one to a friend.
Cheers!

Thanks for that post. I'm expecting my EVOs (I ordered 2) in within the next week. I've been trying hard to find cases and screen protectors without much luck, but I'm going to go ahead and order those screen protectors you mentioned since you recommend them.

Yep i ordered the same ones and love them. i have loved these from the start. they are quite easy to put on and stay on well.

Scotch tape is your friend in getting screen protectors on without a bit of dust

Childofthehorn said:
Hello All,
I know that I want a PET or other glass-like screen protector. Generally speaking, I never used screen protectors because they never really held up all that well and on top of that they never had the feel or look of the real thing. Now I have a scratch on my screen that is not normally visible, but I know its there.
I have run into a debacle because I know that while I am good at putting on screen protectors, I am no expert and the PET ones are harder to get perfect than the rubbery ones (which I now despise). So, recently I have seen that there are some PET/Silicone/ Electrostaic Hybrid screen protetctors and then there are still the PET with Adhesive.
Does anyone have experience with the electrostatic type and how good are they at staying on and bubbles?
Click to expand...
Click to collapse
I have a steinheil ultra crystal protector on my EVO, and its static. As long as you make sure there is no debris under it, it will stay on for a long time with no lifting. I have shown my phone to quite a few people, and not one of them can tell I have a screen protector on it. Even when I point it out to them, they still cant see it. It's very thin and I applied it perfectly so their a no bubbles. Took me about 30 minutes to get it perfect. If you use a piece of scotch tape to pick up debris under it, that works pretty good. This biggest thing is to make sure your edges are perfectly clean. Even the slightest bit of debris under one of the edges of the screen protector, and it wont be long before it starts peeling. I'm very satisfied with my steinheil. Going on 5 weeks now and it looks flawless. Id take a picture but you wouldnt be able to see it anyways. I thought it was a scam spending $13 on a screen protector! I used to order them from china for 50 cents. well, never doing that again! I've only ever used 1 adhesive type screen protector, and it was terrible. the clarity was awful.

OneStepAhead said:
I have a steinheil ultra crystal protector on my EVO, and its static. As long as you make sure there is no debris under it, it will stay on for a long time with no lifting. I have shown my phone to quite a few people, and not one of them can tell I have a screen protector on it. Even when I point it out to them, they still cant see it. It's very thin and I applied it perfectly so their a no bubbles. Took me about 30 minutes to get it perfect. If you use a piece of scotch tape to pick up debris under it, that works pretty good. This biggest thing is to make sure your edges are perfectly clean. Even the slightest bit of debris under one of the edges of the screen protector, and it wont be long before it starts peeling. I'm very satisfied with my steinheil. Going on 5 weeks now and it looks flawless. Id take a picture but you wouldnt be able to see it anyways. I thought it was a scam spending $13 on a screen protector! I used to order them from china for 50 cents. well, never doing that again! I've only ever used 1 adhesive type screen protector, and it was terrible. the clarity was awful.
Click to expand...
Click to collapse
Have not seen these yet. where did you get yours and do you know if they offer an anti-glare

xlrdxrevengex said:
Have not seen these yet. where did you get yours and do you know if they offer an anti-glare
Click to expand...
Click to collapse
Their anti-fingerprint screen protector is also anti-glare per the product description on their website.
http://www.sgpstore.com/product_info.php/cPath/23_33/products_id/1463

remedy22 said:
Their anti-fingerprint screen protector is also anti-glare per the product description on their website.
http://www.sgpstore.com/product_info.php/cPath/23_33/products_id/1463
Click to expand...
Click to collapse
thanks for the link. Can anyone find this brand cheaper

xlrdxrevengex said:
thanks for the link. Can anyone find this brand cheaper
Click to expand...
Click to collapse
I don't think so.
But these are $13 well spent. Believe me.
~fb

Zagg screen protector

Has anyone tried the zagg screen protector for the vibrant? I watched few scratch videos and it looks like it is very durable. What I didn't like is the part where you have to apply it wet. Has anyone tried them on vibrant or any other phone?
Sent from my SGH-T959 using XDA App

Mine shipped on Friday, I'll let you know as soon as I receive it and install it on the screen ... I got the easy kit, full application only to realize that I really only care about the screen ... the back is anyway cheap plastic and the phone already comes with a backup back cover ... meh, spilled milk ...

http://forum.xda-developers.com/showthread.php?t=726134

dcchristopher said:
Mine shipped on Friday, I'll let you know as soon as I receive it and install it on the screen ... I got the easy kit, full application only to realize that I really only care about the screen ... the back is anyway cheap plastic and the phone already comes with a backup back cover ... meh, spilled milk ...
Click to expand...
Click to collapse
lol, same here. But I only got the screen part.
I tried the invisible gadgetguard one though. Same installation process.

I will never buy another one.
http://forum.xda-developers.com/showthread.php?t=739482
I have changed over to the Realook and I couldn't be happier. Much more clear and much smoother.

I have the Zagg Invisible shield (screen only).. I will say it works as advertised as far as protection....
my disappointment is that my screen no longer feels like glass... its harder to use Swype because the screen is kinda rubbery and ur finger(s) dont slide as easily.
ALSO can't swear it's the reason... but trying to (for example) move the cursor when ur texting.. like trying to go back and add a ".... the precision is off... i have to try several times to get the cursor in the right place (makes me miss having a trackball).. I dont recall if this problem existed before i got the shield.

Damn, I wish I had read reviews like these before I dropped closed to thirty bucks on this crap. The protector needs to "cure" but already I can see a couple small (1cm and 2cm) straight vertical lines that at first looked like cracks (I had to throw away that pair of underwear). "Fortunately" I read the recent posts to this thread and found out it's not a problem with the screen. I thought perhaps all the squeegeeing messed it up.
The positive: it protects the screen from accidental scratches and acts like a oleophobic coating that should resist oily fingerprints (I don't know about you but I need that, bad).
The negative: the screen is no longer smooth to the touch so gestures are a little buffered but more consistent (without the shield, it would be best when the screen was clean but it would get jerky when the oil built up); the crisp picture is a little dull.
I don't think the hassle is worth it but I bet when you get that first scratch you'll wish you had the shield on. The grass is always greener on the other side.
Last but not least, at $30 for a piece of plastic, Zagg really needs to deliver perfection. This is just shameful.

If you like the Zagg, you might try www.bestskinsever.com since they're basically the same exact thing, just half the cost. I had them on my G1 and liked it. They're presently working on a Vibrant skin.

dcchristopher said:
Damn, I wish I had read reviews like these before I dropped closed to thirty bucks on this crap. The protector needs to "cure" but already I can see a couple small (1cm and 2cm) straight vertical lines that at first looked like cracks (I had to throw away that pair of underwear). "Fortunately" I read the recent posts to this thread and found out it's not a problem with the screen. I thought perhaps all the squeegeeing messed it up.
The positive: it protects the screen from accidental scratches and acts like a oleophobic coating that should resist oily fingerprints (I don't know about you but I need that, bad).
The negative: the screen is no longer smooth to the touch so gestures are a little buffered but more consistent (without the shield, it would be best when the screen was clean but it would get jerky when the oil built up); the crisp picture is a little dull.
I don't think the hassle is worth it but I bet when you get that first scratch you'll wish you had the shield on. The grass is always greener on the other side.
Last but not least, at $30 for a piece of plastic, Zagg really needs to deliver perfection. This is just shameful.
Click to expand...
Click to collapse
Just request a full refund. They should honor their money back guarantee as long as you're still within the time period.

Just received mine and really am not disappointed with the product it is a little less glass like but is not hard to use swype, clarity seems the same and screen response is about the same I could tell a little drag with the screen nothing crazy,i will say onr thing that confuses me is the back cover does not even cover the edges which is very word to me considering that's the most likely part it will land on. I'd give it an overall 7 out of 10. For the price there are better alternatives but it willdo the job. As far as the vertical line problem I cannot comment on that as mine did not have that problem.
Sent from my SGH-T959 using XDA App

I took it off ... got tired of looking at the wavy pattern of the plastic and the two "imperfections" on the shield ... I'd rather look at scratches. Plus, trying to swype only to fall short of the letter I was aiming for got old quick (the skin loses momentum from the extra resistance that the membrane introduces).
Anyone who claims their screen looks roughly the same after the Zagg Shield treatment is smoking something that he/she should share with the rest of us.
I also contacted Zagg regarding a refund ... let's see how that goes.

dcchristopher said:
I took it off ... got tired of looking at the wavy pattern of the plastic and the two "imperfections" on the shield ... I'd rather look at scratches. Plus, trying to swype only to fall short of the letter I was aiming for got old quick (the skin loses momentum from the extra resistance that the membrane introduces).
Anyone who claims their screen looks roughly the same after the Zagg Shield treatment is smoking something that he/she should share with the rest of us.
I also contacted Zagg regarding a refund ... let's see how that goes.
Click to expand...
Click to collapse
I took off the Zagg too. I just couldn't handle the look and feel.
Go get the Realook and you'll be very pleased. Search Realook Vibrant on Ebay and get it from the seller "realook". Shipping is free and super fast (I got mine in two days and other have reported next day delivery).

Pneumatic said:
I took off the Zagg too. I just couldn't handle the look and feel.
Go get the Realook and you'll be very pleased. Search Realook Vibrant on Ebay and get it from the seller "realook". Shipping is free and super fast (I got mine in two days and other have reported next day delivery).
Click to expand...
Click to collapse
Thank you sir! I will check it out.

BTW, folks, if one searches for Samsung Galaxy Gorilla, one finds many references to the Galaxy S phones having a Gorilla screen that is scratch-resistant (which is an understatement for the kind of abuse they can withstand). Sounds to me like many of us wasted time and money to protect something that didn't really need the protection. Just my two cents (albeit very, very late).
Good luck to all with their screen protection strategy.

Ghost Armor...
Ghost Armor...look into it! thinner than invisible shield so it's more responsive and doesn't get that orange peel...same lifetime guarantee, overall better product!

Well I got my 2 zagg screens, applied first 2 nasty vertical lines on the screen. removed it next day. Applied second thought what are the chances in getting two defective screens... same thing but this time only 1 line. Keeping this one on until my realook arrives.

Love my screen. Invisi sheild ftw
Sent from my SGH-T959 using XDA App

I thought I'd input my 2 cents on this topic:
I got this directly from the manager of the 3M distribution facility for my area...
3M owns the patent for this kind of protection film.
Clearbra, Zagg, BestSkinsEver, basically anyone saying their product was designed for military use (on helicopter blades), they are all getting their materials from 3M. The only difference between vendors is the measurements they take, and ultimately the template they use for the application.
It sounds like Realook is a different material since it doesn't have that same rubbery feel to it, so they are probably not getting their stuff from 3M.

brodie7838 said:
It sounds like Realook is a different material since it doesn't have that same rubbery feel to it, so they are probably not getting their stuff from 3M.
Click to expand...
Click to collapse
Having had both on my Vibrant I can tell you that they are definitely different material. The Zagg is flimsy rubber feeling material that requires water to install, the Realook is a harder plastic feeling material that appears to cling to the screen as it touches it.
After having both on the phone I can say without a doubt that the Realook is the superior product. It goes on easier, it's transparent, and it feels like the original glass.
Side note... I showed a buddy my phone the other day and he was playing around with it for a few minutes watching Avatar and playing a game. As he handed it back to me he said "you going to put a screen protector on there?" I said "It already has one". He looked again and he still couldn't tell that it was there, even after I told him.
Realook for the win!

Xtreme Guard Screen Protectors - $1.99 ea

Pretty cheap, and if you need to replace one, you're not out much
http://www.ebay.com/itm/320803239584?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649#ht_2415wt_1373

Normally one of the first screen protectors on ebay after a phones release. Im not of fan of wet installation screen protectors. You get what you pay for. Mines barely lasted a week.

I've used those Invisible Shields for a LONG time. I'm a big fan, but not for touch screen devices. They're good for the sides and the back and such, but I don't care for them for the feeling they have when you try to slide your finger over the "glass." Strange. Regardless, if you DO like them, I'd highly recommend Zagg Invisible Shield. They're over priced but they've never let me down yet.

i don't get it guys? how is that the screen protectors fall off your phone? if you install it properly without any bubbles last even 1 year.unless gets too many scratch on it and i wanna put on a new one.never happend to me.and i always buy cheap ones.like 10 pieces for 3 pounds!
cheers!

Bad. Real bad stuff. They are kinda stuffy. Soft. More like thin layer of rubber. Can barely be used for touch screen, without having touchy fingers.
I bought them for my Samsung Focus and they aren't really good for the screen. For the sides and back, this case might be ordered.

vasishta.sushant said:
Bad. Real bad stuff. They are kinda stuffy. Soft. More like thin layer of rubber. Can barely be used for touch screen, without having touchy fingers.
I bought them for my Samsung Focus and they aren't really good for the screen. For the sides and back, this case might be ordered.
Click to expand...
Click to collapse
They have sold over 300 of them. I guess if they are as crappy as you say, I will say so in my feedback.

I bought one. Was actually just looking for a dry screen protector. Didn't realize it was similar to a zagg shield until I opened it up.
If you follow the directions it only takes a few minutes to apply.
I don't like the rubbery feel...but for 2 bucks it works. Just a side note...if you use the s pen you can see the markings on the screen protector. I'll be on the lookout for a cheap replacement because that is a little annoying.

^^^
Did I not tell ya That thing is good enough for everything but the screen.

I just got one partly due to prices, mainly per delivery time-fastest. I didn't know it was a wet installation and with the feedbacks i am apprehensive on using it. Any problems peeling it off the screen and did it leave unremovable streak marks for those that have used it?

No problems with the removal or leftout marks. At least give it a try.

There is no REAL issue with it, and if it's properly installed it will last a while. I don't use any additional cases and all the in-out action of my pocket usually takes off the screen protector, sides, or back within 2-3 weeks.
It has sold over 300 of them because they're so cheap. People will say "for two bucks, I'll give it a try" and even I was about to buy one until I realized that it's a zagg pretty much. Gimme a TPU / Hard shell case any day and those e-cell screen guards and I'm good.

any screen guard which dosent get scratched with s-pen?

Have one on my note, got ripped off cause I have bought it on the official website for five bucks. Personally, the rubber skin feels right, I have the same on all my other devices : touchpad, sgs 1, sgs 2, transformer, etc...
But with Note it is just impossible to make it last longer than a month with the s pen : I drew like 2 minutes and there already is several deep scratches in the rubber layer, very annoying and it messes the vision of the screen.
So for the note it's a no go imho, I'll invest in a dry protection I guess...
Sent from my GT-N7000 using XDA App

Just got mine today. They are thick and seem durable, but you simply cannot use the stylus on it effectively. That must be why they're $1.99

Yeah it is annoying the indentations caused by the stylus, but at least it is offering me protection while I wait for my long term solution to arrive by mail

I bought one of those $1.99 screen protectors for my note, had it on for 5 minutes then promptly ripped it off and threw it away. The S-pen leaves trails and I was hoping it would be clearer than the matte finish protector I received with the phone but it was just as fuzzy or rainbowish. Waiting on an Ultra Optic now and will accept it even if its not as clear as I want.

Nexus 5 Screen Protector Warning

I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.

The xtremeguard screen protectors are really good, and they can be found for under $2.

mprasolov said:
I just thought I should share a valuable lesson: DON'T BUY CHEAP SCREEN PROTECTORS!
I have been fine in the past with cheap screen protectors from eBay. They got the job done, and they were only a dollar or two. And you got six of them.
Anticipating the arrival of my N5, I bought a Spigen Neo-Hybrid case (Which is excellent), and some cheap screen protectors for $2. (12 to be exact)
http://www.ebay.com/itm/231089059032?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I bought a bunch because that gives ample headroom if you mess up a few times.
I try to install the first one, and it ends up with bubbles near the cutouts for the speaker and camera. Okay, I'll just try another one.
I've gone through six of them, and they all have the same bubble problem near the cutouts.
I ended up buying higher-end screen protectors: http://www.amazon.com/gp/product/B00EV97UD6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
I'll be sure to report on those when they arrive.
But the lesson is to be cautious with cheap screen protectors.
Click to expand...
Click to collapse
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.

BigOkie said:
I've got some of the iSmooth protectors and they are quite good...once I properly installed them. Dry apply are a little tricky but there are enough tutorials and videos to help. I also have the Neo Hybrid and I'm quite happy with it.
Click to expand...
Click to collapse
I guess I lucked out with my choice of screen protector!

Not necessarily. I bought these SAMAR crystal clear screen protectors, managed to apply one without getting any dust or air bubbles. It has all the cutouts, the fit is good, and it is quite smooth when swiping, very happy with it so far. To top it all off it is dirt cheap and you get 6 protectors all with cleaning cloths! I've read others on here who have been happy with this brand too. Would definitely recommend.

use a drop of water when u install. it'll help take out bubbles.
also you can reapply these, just rinse in soap water then water, then shake off excess and apply. squeegee out the water - should be next to nothing.

ktamondo said:
The xtremeguard screen protectors are really good, and they can be found for under $2.
Click to expand...
Click to collapse
True. And even with that. I got one first and tested before I got backups.

I use an IQshield screen protector and it's nothing short of pure awesome. No bubbles at all, and it's so smooth and dried hard. It feels like glass.

You get what you pay for. I bought the spiegen Crystal for 10 bucks and they went on perfect and looked perfect and felt pretty good to you cant even tell its on unless you look at the earpiece closely. But there's always better! I just recently bought a Nillkin Glass screen protector with 9h hardness and olephobic with rounded edges and its gonna be getting here in a week or so and that should be way better than a cheap or high quality screen protector!

This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
second, and heres the silly part: I make sure the screen is completely wiped, and blow on the screen itself with DRY LIPS as im applying the screen protector face down. This blows off any dust that may settle between the time you apply the screen, and make sure lips are dry as to not blow moisture onto the screen.
There really isn't any fool proof method for applying screen protectors without dust, but without some sort of clean box with a built in HEPA filtration system, this seems to work well for me 80-90% of the time, versus just applying like normal.

unvaluablespace said:
This sounds silly, but whenever I install a cheap screen protector, I do two things: first, i make sure the side that's going to be applied to the screen is FACE DOWN. Never face it up, under any circumstances. if I do, its before removing from packaging. I even remove the adhesive that protects the protector itself, with the screen protector face down. this doesn't give a chance for dust to sit on the bottom of the screen when facing up. Yes im sure any dust flying around will still find a way to stick, but this reduces the chances. Plus, you make sure you are applying in a clean environment anyway. I usually vaccum the house (or area at least) prior to applying, and give the dust time to settle afterwards.
.
Click to expand...
Click to collapse
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.

Caelrie said:
You can skip all the surgical-precision vacuuming if you do the application in the bathroom. Turn on the shower, hot as it'll go. Leave it run for 5-10 minutes til the bathroom is steamy. That knocks all the dust out of the air.
Then you can apply your screen protector in peace.
Click to expand...
Click to collapse
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol

The moisture will get out over time. Its just like having windows tinted
Sent from my Nexus 5 using Tapatalk

unvaluablespace said:
but wouldn't that cause moisture in the air? I could see that getting in between the screen during application. I bought a ton of screen protectors like OP though, so I'll have to give this idea a shot lol
Click to expand...
Click to collapse
It doesn't matter. Even dry-applied screen protectors go on better this way, and any moisture completely dries out quickly anyway.

Spend a few hundred dollars on a phone and then buy the cheapest cases and screen protectors you can? Doesn't make sense.
I'll pay the extra $8 for a Spigen screen protector and a quality case that match the quality of my Nexus.
Sent from my Nexus 5 using Tapatalk

Spigen could've tried a bit harder and made all the cutouts. Even the temporary screen protector that comes with the phone has those. I think most screen protectors will be similar at the $1+ range but you can't expect much from ones that cost $0.25.

xtremeguards didn't have bubbles for me. Buying 6 of the same screen protectors and then saying all of them have problems doesn't make sense.

I'm assuming the OP means the bubbles are from the edge of the cutouts not sticking down which is a common issue with cheap screen protectors.
the cutouts are not made well so the screen protector itself is warped at the cutouts for the speakers etc so its not flat and does not stick down creating bubbles there.

Just install in steamy bathroom. The steam prevents dust from floating in the air.
Sent from my Nexus 7 using XDA Premium HD app

I got this Nillkin one: http://dx.com/p/277084. I only had one. Applied by using the "hinge" method. Went perfectly. Cutouts are perfect and bubbles are removed very easy (easier than other screen protectors I've had).
I used a little wet cloth to make my screen wet and to remove dust. At first it feels very rubbery, but after using it for a day or even less, it feels just like the glass!