Related
I've used many different kinds of screen protectors in the past, and this time I tried XtremeGuard which I found on eBay. The cost was only $2.50 shipped. I must say hands down, this is the best screen protector I have used.
Other kinds I've used in the past were a thin hard plastic, kind of like a clear overhead sheet, but thinner and sticky on one side. These were not good IMO, because they make the touchscreens less sensitive and since they were hard, the edges would start to peel first and it would be all downhill from there.
The XtremeGuard is a more stretchy film material, kind of like 3M clear bra, or the kind you would find on a car. Its got a nice grippy rubber feel to it, which I actually like. Its "softer" so it sticks better to the screen.
I used a mild soapy water solution to put it on, and at first was kind of concerned with my results. Some areas were cloudy, there were some visible bubbles and when the screen was on it looked all rainbow cuz of the water trapped inside. After a couple days though, all the moisture evaporated, the cloudiness cleared up and all the bubbles were gone. I was left with a perfectly crystal clear screen that adhered all the way around, even on the edges. You would not be able to tell there was a screen protector on here (I have the OEM HTC silicone skin that covers the edges as well so you can't see the edge of the screen protector). The touchscreen works perfectly, and the screen protector does not interfere at all.
The screen protector was the exact size of the screen, perfect cut. Which is good, but makes it challenging to install, if you're off by a tiny bit, the screen protector will stick off the screen and that will be prone to peeling up later on. So take your time during the install to ensure its on there straight and perfectly. I started from the top where the speaker is and lined it up around those lines, and used a credit card to press it down and get as many bubbles out as I could. If this is your first time installing a screen protector, I would suggest getting 2-3 to make sure you get it right. At only $2.50ea, you really can't go wrong here. I'm 100% satisfied.
http://cgi.ebay.com/NEW-XtremeGUARD...ewItem&pt=PDA_Accessories&hash=item35a9e73eed
I would also like to note that I do not work for, or am in any way affiliated with XtremeGuard at all. I simply tried their product, and I liked it, so I'm leaving my feedback here.
I have tried it, but it is like a mm to long on top to bottom. And it was like 2mm to short in width.
That was my experience. Could be wrong for everyone.
I like mine, it fits perfectly. Doesn't stick over the edge and covers the whole thing. Mine was a perfect fit, not too long or short on any sides.
I'll try to get some pics up later when I get the chance
Man, I want to order it so bad, but with Otterbox covers around the corner, I think its a little waste of money.. :S
Any tackiness or stickiness with this protector? I'm currently using Phatom Skinz and love it, but I'm always looking around for something that may potentially be even better...especially with a price like this. How about orange peel?
thanks,
Alan
There is a very slight tackiness with this screen protector, but I actually like it. It gives a good feel when typing. It might interfere with pong or some other games where you need to move your finger really fast, but that doesn't really apply to me.
No orange peel, or any peeling at all for that matter.
The cloudiness really bugs me. The Zagg I had did not cloud like this one does.
The item from ebay is too pricier. This site offers products with much lower price and free shipping world wide. The 3 packed screen protector is much cheaper than 1 packed from ebay.
http://www.geartaker.com/product/3x...opers&utm_medium=minqing&utm_campaign=FA0070B
this 3 packed protector was once sold at $0.01 during its 2nd super deal.
Hey guys, I recently bought one of these off Amazon when I ordered my Otterbox case, it was only $2 so I figured I had nothing to lose. Here's my take on it.
http://forum.xda-developers.com/showthread.php?p=19109961#post19109961
A bit of caution when picking out screen protectors
I had to cut the edges on my AT&T screen protectors due to the nature of the soft back which when pressure is applied to the front causes lifting on the screen protector's 4 corners. The dimensions are fine but the radius is too small for the corners causing them to protrude ... just cut them a little but I would have preferred to have 100% perfect screen protectors instead of half assed ones from AT&T ... why am I not surprised.
sentinel79 said:
A bit of caution when picking out screen protectors
I had to cut the edges on my AT&T screen protectors due to the nature of the soft back which when pressure is applied to the front causes lifting on the screen protector's 4 corners. The dimensions are fine but the radius is too small for the corners causing them to protrude ... just cut them a little but I would have preferred to have 100% perfect screen protectors instead of half assed ones from AT&T ... why am I not surprised.
Click to expand...
Click to collapse
I purchased the same protector. I have the same issue as well. Makes it look really cheap with the corners sticking up.
I had that, plus since I am opening mine a LOT for hacking, the bottom looks like crap.
Looks like I am going to replace the protector within a week of getting the phone.
Just wrap the whole phone in plastic wrap with the back off. Then slip it on.
Bad idea most likely, but it would be funny if it worked well.
same issue. Trimmed the corners. It doesn't look that great, but doesn't peel up when i hit the corner on something. I'm on the third protector already. First one i screwed up the orientation and got dust under it when fixing. second peeled up when i hit one of the corners.
must be those poor quality screen protector. there us not much of an option atm. i would rather get a HTC HD mini screen protector and punch a hole on it.
I just had Ghost Armor put on my iPhone 3G (which I'm handing to my daughter when my Aria comes in). It's pretty nice, but the Aria isn't showing up on their website yet. And you would only really want to get the screen done, since you open up the phone to get to the battery and the SD Card.
Yep, I cut them carefully and used the scotch tape method to get perfect placement.
-------------------------------------
Sent via the XDA Tapatalk App
sentinel79 said:
Yep, I cut them carefully and used the scotch tape method to get perfect placement.
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
Can you elaborate on the "scotch tape method"?
I ordered invisible gadget guard from amazon. Havent put it on yet, but that packaging sure makes it look impressive.
Before separating the films I placed tape to use as handles to apply the protector flat (instead of holding it).
Then after layed down on the screen pulled up and slid tape underneath to attract any particles which cause bubbles. Slide with sticky side face up so it pulls from the protector's sticky film (rarely do the particles stick to the screen itself).
Sent from my HTC Liberty using XDA App
Has anybody noticed the quality of these are not that great?
Have had on for 3 days. There are a LOT of scratches on the protector itself. I usually keep phone in jean pockets with a wallet.
Anybody plan on trying the Amzer ones, although I have heard their quality may be dubious too for the n1.
Shad0wguy said:
I ordered invisible gadget guard from amazon. Havent put it on yet, but that packaging sure makes it look impressive.
Click to expand...
Click to collapse
I ordered this, and it shipped today. I got my 8 GB card in the mail today, too. I kind of wished I had gotten a 16 GB card, since my whole music collection is about 8 GB. But I may pick up another 8 GB as my "backup film roll" at a later time.
Donatron said:
I purchased the same protector. I have the same issue as well. Makes it look really cheap with the corners sticking up.
Click to expand...
Click to collapse
I can't believe I didn't figure out this solution earlier. Obviously, trimming the excess on the corners would solve the issue, but I wasn't comfortable using a razor blade to make the trims. But just 5 minutes ago, it occurred to me to use a nail clipper (while already installed on the phone, and the back plate removed). Worked perfectly, was super easy, and did no damage to the phone.
Yeah that didnt occur to me either. I used small crafting scissors.
Sent from my HTC Liberty using XDA App
Same thing happened to me, just on the bottom corners though, but as soon as I put my case on it covered up those bubbles, cant even see it. Quality of the protector seems to be decent. I used a universal one prior and it was ****!
I ordered the stealth guard though for the phone (full body protection) just now so when that comes I'll let you guys know how that works out as well.
I used the Invisible Gadget Guard that someone else mentioned (got it off ebay though, not amazon, it's the exact same one however). The quality of it is definitely top notch, I've had it on for a little over a month now and it has no scratches/marks that are visible without actually looking for them and even then there are minimal and very minor ones. My one complaint with it is the top two corners did start to peel a bit, I ended up peeling it up a tad and cutting them (with difficulty, this thing is tough!) and reapplying that part and I haven't had a problem since! I do have a few blemishes down the left side due to my clumsiness during the initial applicaton, but the case covers it for the most part
i tried the invisisheild and did not like the rubbery feel, got at t sheild it is a hard plastic and fingers slide much better, yes i had to trim but no big deal there. all you have to do is put the protector on the phone with back cover off, then take a new sharp razor blade at about 50 degree angle to the edge of glass and trim excess off. 3 months now and have not lifted any corners. these are much better than the rubber vinly covers that tend to stretch and need trimming as well.
If so does it do a good job with the light glare and make fingerprints less noticeable ?.
I have a matte screen protector on my Xoom and it does cut down on finger prints, glare and it makes it easier to slide my finger over the screen
I use a steinheil antiglare matte screen protector. Love it. Great at resisting fingerprints. Reduces reflections alot. And just as important,as mentioned by player-x, is how your finger slides much easier on the screen. Great when playing games. It feels really good under the finger
PS live in the UK and so had to order it from states
Sent from my Xoom using Tapatalk
Got this one from Amazon. It's definitely better than the shiny screen it comes with, and it cuts down on fingerprints, though there's still fingerprints. It feels much nicer on the fingers. The one downside to this type of screen protector is that it's difficult to get it on perfectly straight. This one is cut almost perfectly to fit the Xoom screen, but that means there's very little room for error. I thought I had mine on straight, but the edge is just a hair over the raised part of the bezel and now there's about a 1cm bubble on the edge. Can't retry though, once it's on, it's on...
http://www.amazon.com/gp/product/B004VT4CHI
Anyways, I'd buy it again.
Slack, are you sure you can't use parcel tape to raise the screen protector without damaging it? Stick the tape to the corner of the screen protector with a flap of the tape sticking off the edge of the screen, then pull up on the tape and the screen protector should come with it allowing you to reposition. Works with my steinheil sp
Sent from my Xoom using Tapatalk
Like others, I'm using the Steinheil, and it's pretty damn good. Difficult to apply though (see the thread devoted to the Steinheil for help on this front).
Fingerprints are barely noticeable and glare is eliminated. I still have to wipe it down about once a week, but that's a lot better than daily.
I went with NuScreen on my Xoom. it's basically a wax that you apply which does a great job at cutting down on fingerprints. I put some photos of it up here:
http://cadince.com/fingerprints-on-my-screen/
It doesn't help with the glare though, but that wasn't my main complaint.
I went with the SGP (Steinheil) matte cover as well, difficult to apply but amazing once on.
I got this screen protector for $6 from gizmodorks. it works great, installed easy and feels very nice. I used THIS guide when I installed it and everything came out great.
I have these
http://www.handhelditems.com/motoro...finishing-screen-protector-pack-p-161101.html
As with all static screen protectors you need to install them in the absolute least dusty room in your house otherwise all this stuff instantly starts attracting to the shieldand basically ruins it. I installed mine in my garage and managed to install it with one a single small fiber seeking in.
I love these screen protectors. The downside is that these matte protectors so leave the display slightly blurry compared to stock and it takes some getting used to at first. But the feel when using your screen afterwards is much much improved and is well worth the trade off. I'm completely used to the look now, I barely remember how it was without the protector now lol.
MrGinger said:
Slack, are you sure you can't use parcel tape to raise the screen protector without damaging it? Stick the tape to the corner of the screen protector with a flap of the tape sticking off the edge of the screen, then pull up on the tape and the screen protector should come with it allowing you to reposition. Works with my steinheil sp
Sent from my Xoom using Tapatalk
Click to expand...
Click to collapse
Sure, I did that a couple of times when getting it on there. It's also risk/return: the more times you try, the more chances of getting a bubble or dust under there. Since I got almost none of either, I decided to cut my losses. was also considering going at the edge with an exacto, but probably not worth it.
What would be awesome is if there was a wet-application matte protector. I'd be all over that in a second...
The adhesive on the front face stays a bit after you peel of the protector. Initially I thought this screen protector wasn't great because it felt like it added too much drag when swiping, but wiping it down with lens cleaner made it as slick as the bare screen.
This is an outstanding screen protector, the best I've ever seen, shines in every area. Highly suggested to those considering it.
After reading pages of reviews on the screen protector, seems like SGP Ultra Nano Clear got some good votes.
But I didn't like the clear on my wife phone vs mine had anti-glare cleaner.
It resist finger prints and residue and the swiping feels good too brand was (Green Onion: Rota Anti-Glare).
So I end up order a pk3 anti-glare & anti-finger print from Tech Armor for $9.99 bucks http://www.amazon.com/gp/product/B0088OJXE4/ref=oh_details_o00_s00_i00.
The SGP Ultra Nano Clear was $13.99 pk3 is a pretty good deal, but I hope Tech Armor is a good choice once I get it, I'll post a review for sure...
sw07tc said:
after reading pages of reviews on the screen protector, seems like SGP Ultra Nano Clear got some good votes, but I didn't like the clear on my wife phone vs mine had anti-glare cleaner and less finger prints and residue, so I end up order a pk3 anti-glare & anti-finger print from Tech Armor for $9.99 bucks, the SGP Ultra Nano Clear was $13.99 pk3 is a pretty good deal, but I hope Tech Armor is a good choice once I get it, I'll post a review for sure...
Click to expand...
Click to collapse
they sell an optics version you can get that's supposed to have less glare. i have the Nano clear and i can say it's amazing. you can barely tell it's there and it's very click. kudos to SGP.
Yes, I saw that but I wouldn't pay $19 for just screen protector.
http://www.amazon.com/SPIGEN-SGP-Sa...57&sr=1-1&keywords=sgp+ultra+optics+galaxy+s3
I put my nano clear on a few days ago and am very pleased with how it works. Feels basically the same as the bare glass & is extremely clear. The only thing is I screwed up the first 2 trying to put them on they were not aligned exactly right and the third I still managed to put it just a tiny bit too much to the left so that a very slim wedge in the top right of the screen is not covered and the front facing camera has a little bit of the protector blocking it. luckily I don't use the camera but I would really like to take it off and try again but do not want to pay another 17 dollars to do so..
Anyone think if I emailed sgp they might send me another one to try again? lol
extreme11191986 said:
I put my nano clear on a few days ago and am very pleased with how it works. Feels basically the same as the bare glass & is extremely clear. The only thing is I screwed up the first 2 trying to put them on they were not aligned exactly right and the third I still managed to put it just a tiny bit too much to the left so that a very slim wedge in the top right of the screen is not covered and the front facing camera has a little bit of the protector blocking it. luckily I don't use the camera but I would really like to take it off and try again but do not want to pay another 17 dollars to do so..
Anyone think if I emailed sgp they might send me another one to try again? lol
Click to expand...
Click to collapse
you can get this back off by taking a piece of tape and lifting the protector off. when installing these things, i never let them cling completely until i have it lined up okay. mine is a tad off around the home button, but perfect alignment around the speaker and FFC. you would think this would mean the protector goes diagonal on the phone but the edges are also lined up good, with just a smidgen more of the protector being on the right side.
anyway, try that. you may end up getting some dust under there doing this. just use the stickers they provide and use more tape to lift up, then the sticker to grab the piece of lint/dirt. very easy. just takes A LOT of patience.
edit: also, always make sure you start with the top. i wish SGP included more of those stickers. would make installing these a breeze because you could just stick one at the top and one at the bottom under the protector in case you needed to re-lift.
lol I started on the bottom which I guess was my first mistake. I wanted to make sure it didn't get on top of the home button at all..
So you think it will still stick good if I peel it off with a piece of tape to try to align it better?
In my experience, attempting to re-position the ENTIRE protector ends in disaster every time. Bubbles, dust, worse positioning... but I'm also like you: I tend to buy 3 screen protectors knowing the first 2 are going to end up being trial runs for the 3rd
K
extreme11191986 said:
lol I started on the bottom which I guess was my first mistake. I wanted to make sure it didn't get on top of the home button at all..
So you think it will still stick good if I peel it off with a piece of tape to try to align it better?
Click to expand...
Click to collapse
it's very possible, despite what the person above me just said. you just have to be meticulous with what you're doing. if it's already messed up then it's not gonna be any worse. start with taking the bottom up first. be sure not to flip the protector over as you are pulling it up and taking it off. always leave the side that contacts your screen facing your screen.
bubbles come from something getting trapped between the protector and screen. when you go to squeegee it with the plastic card, if the bubble doesn't move over, that means you trapped something in there. use another piece of tape to lift and then use the stickers they provided to grab whatever is in there. i had to do this at least 4 times on mine after i got it placed good enough.
it takes time to do it this way, but it has always worked for me. the difference between me and someone who doesn't care as much... my gfs phone has bubbles on her screen and i can even see what was trapped. mine has absolutely no bubbles. a co-worker handled my phone and i told him after about the screen protector. he didn't even know it was there and there's no case around my phone yet hiding the edges...
I guess I am hesitant because besides the fact that it is not aligned just right there are absolutely no bubbles or marks or anything underneath the protector it looks fantastic. Will probably just leave it for now but thanks for the tips
does the Nano have any issues with the edges lifting? I bought the ultra crystals before they discontinued them because of that problem. Since these are thinner I'm hoping that issue is resolved.
images would be greaaat!
extreme11191986 said:
I guess I am hesitant because besides the fact that it is not aligned just right there are absolutely no bubbles or marks or anything underneath the protector it looks fantastic. Will probably just leave it for now but thanks for the tips
Click to expand...
Click to collapse
I've had luck peeling it off, rinsing with running water, soaking it in hydrogen peroxide, shaking it dry, and doing a wet install of sorts. You may also want to dab a bit of the peroxide onto the top to squeegee and not damage it.
I found this Screen protector on Amazon and what caught my eye is that it wraps around the side of the phone onto the back. at 2 for $15 CDN it was worth trying.
https://www.amazon.ca/gp/product/B06ZZ5Q95L/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Application:
It was a little rough, the first one had too much adhesive. While trying to take off the 1st part, the Adhesive side, it actually peeled the 2nd part, the screen protector side off. It took a lot of force to get the Adhesive side off the screen protector itself, that i ended up ruining it. However the 2nd sheet was much easier to peel apart. The Adhesive layer comes off in 3 parts. the Screen and one for each side. Lining it up was fairly easy using the speaker, sensors and camera at the top. Once it was on properly, the sides wrapped around to the back of the phone. It's easier to smooth out the bubbles before putting the sides down.
Looks:
It looks really clear but when at an angle with a light there is an orange peel effect but this may have been from over zealous rubbing to get the bubbles out. Regardless I am quite pleased at how good it looks over other film screen protectors I've used in the past with other phones.
In a Case:
I'm using a a Spigen Tough Armor Case
https://www.amazon.ca/gp/product/B06XP4FP8N/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
The screen protector has a very small clearance at all corners, when applied properly the corner of the case won't touch it nor lift it. Since it wraps around it will not lift it from the sides either, or at least shouldn't. I haven't been able to put it though any long term tests but then again i don't plan on taking the case off any more than i really have to.
Now what you all came for, pictures!
http://imgur.com/a/dNSCY
I was about to order the white dome but the review about the prominent lip tuned me to iqshields full body since I will have the phone naked in a holster. I was thinking about the liquid shields next but maybe I'll try this one the next go around if iqshields doesn't work out. Thanks for the find!
I do not see how that wrap around will work. There will be air pocket around the seem .
Sent from my SM-G955U using Tapatalk
I just installed one on mine and I dont think you will find a better one than this at this point in time. Its is case friendly with the 3 cases I have tried at this point. UAG, Spigen Liquid Armour, and a Ringke case, the corners are just to the point where they dont touch the case corners. The only potential area of issue for me is after putting on the screen protector (which for me went flawless after watching the youtube install video) was the area around the Power, Volume and Bixby buttons. After putting the case on it wants to "bubble" a bit in those areas. But once I rolled my finger over the edge, pulling back the case slightly it laid the protector back down. its only been a couple hours but so far so good and Im way happier with this $12 purchase over the 45 whitestone dome that seems to be hit or miss.
Photos were taken with the Spigen Liquid Armour case on. Also taken with my tablet so quality on a couple of them are crappy but you should get a good idea,
tiny70thomas said:
I do not see how that wrap around will work. There will be air pocket around the seem .
Sent from my SM-G955U using Tapatalk
Click to expand...
Click to collapse
Just imagine starting off at the edge of your phone to getting started and rolling the phone up like playdoh or a joint smoothing along as you go...to easy!
Thinking about ordering a set of these up. I don't like the orange peel look and the top does not look too case friendly. Does the orange peel smooth out over time or is it permanent?
Personally my opinion of this screen protector as I just purchased and returned it to amazon:
-it messes white whites on your screen. They dont look good anymore after I applied the protector.
-While it does wrap around the sides, when you put on the case it still lifts up the corners and creates little air pockets on the sides of the screen
- Extremely orange peel look on this screen protector.
I purchased the IQ shield case friendly updated version and the image quality is WAY better than this ringke one. Using the IQshield I can actually say for certain it feels like there isnt a screen protector on, with my eyes and my fingers. The ringke you can immediately with just your eyes tell there is something off due to what it does with white balance.
My advice is, dont buy the ringke, there are better ones out there.
felloffthetruck said:
Thinking about ordering a set of these up. I don't like the orange peel look and the top does not look too case friendly. Does the orange peel smooth out over time or is it permanent?
Click to expand...
Click to collapse
if it's lined up properly there is a tiny gap between the screen and the case, so it shouldn't lift. I only had it for a few day and it's getting less and less but i don't think it'll go away completely since i was a little over zealous trying But when i'm using it, it's barly noticable if at all. It's only when a light shines on the screen.
It's not for everyone but i feel it does a good enough job for a lot of people to be happy with. The fact that it wraps around is it's main selling point as it will completely protect the edge screen and the case won't lift it up IF applied properly
I applied one to my S8+ this morning. I think it's great for what it is. It's not glass, but it's smooth and feels like nothing is there. There's an ever so slight orange peel look, but I only notice it when looking at the phone from an angle in light, and it doesn't look like I'll have any lifting from my Ringke case. Overall I'm very pleased with it.
Why not try the BestSkinsEver protectors ? I actually have the edge-to-edge one installed w/ a Ringke Slim case and it is not lifting at all. I thought it would, but actually, it isn't. Now, I would like to use my Spigen Slim Armor case but when I put the phone in there, the corners started to lift up. My BSE case-friendly protectors came in but I will probably wait to install it at a later date.
This is the real deal. Hella nice! Works with my rhinoshield as well
Only issue I've found so far is that the side flaps distort the button mechanics. Takes more force to unlock phone and volume up/down
They'll break in tho. Love the combo