Related
I was tired of waiting for SGP to get their $^#& together and decided to get yet another case.
I got this Perforated Retro Sports Case from Fommy.com.
http://www.fommy.com/view-full-page.asp?divid=Samsung&model=Samsung+Vibrant+T959&skuno=89299
I'm not sure what makes it "retro", but it is a nice looking case. It's a combination of hard plastic (the perforated area) and flexible plastic sides. It's thin - not like the Samsung mesh or Case Mate Barely There - thin, but probably a touch thinner than the average TPU case.
The case covers all sides, although you can still see a bit of the bezel. However, unlike a different case I tried, the amount that peeks out is consistent all around so it still looks nice.
Now, it's not without it's quirks - which may be deal breakers for some. First there are no cutouts for the speaker or the mic. The speaker is no big deal because the case is perforated - I didn't really notice much difference in volume of some music I tried. The mic, on the other hand, required a hammer and nail to deal with. It was pretty simple, though. I just lined up the hole from another case and then hammered a small nail through. It works just fine and I tested some calls with no reports of sound loss on the receiver's end.
The other "quirk" is that the cutouts on the top and sides are a little strange. The one on the volume side is really long and spans over the rocker keys and the strap-loop-hole. It's tapered well along the edges so it doesn't look bad or anything, just a little odd. The top opening also spans across both the jack and the usb port. This makes the bar along the top feel a little less solid than the rest of the flexible areas. I would have preferred they used two separate openings on top rather than one for the extra support. It's also cut rather close to the port, so if you are using a thick plug, you have to move the plastic up a bit. A little annoying, but at least you don't have to take the case off to plug it in like with some cases.
Things may change after a week of use, but my initial impression is positive. Overall, the case is very nice and is unique compared to the other stuff that's currently available. I do, however, think it's a bit pricey at $14.95+shipping (around $5 for super saver). But hey, money grows on trees.
Just ordered mine, From the looks of it, I think i will like this case better than the perforated plastic snap on case. This one looks like it offers full phone protection. tell me if the case would protect the phone in the event of a fall or drop. Rate its protection from a fall as either minimal, moderate, or maximum protection. I would appreciate your advice. Thanks
Since it covers all sides the protection is going to be better than the snap on. But its thin and pretty stiff so impact resistance is probably minimal to moderate at best, especially compared to silicone or TPU.
Sent from my SGH-T959 using XDA App
thanks for the review, but i would be worried about knowing from the get go that i would need to use a hammer and nails to get a plastic case to work.
mikey98277 said:
thanks for the review, but i would be worried about knowing from the get go that i would need to use a hammer and nails to get a plastic case to work.
Click to expand...
Click to collapse
Very true. I didn't try calls before making the hole so I'm not entirely sure it's necessary (although I imagine you would get a drop in sound quality with the hole covered).
I love this case. It is slim and perfectly follows the contours of the phone. The only thing that i didnt like was the hole missing over the microphone. But the texture and quality of the case is top notch. I have the mesh galaxy s back cover, the tpu grey argyle case, the body glove rubber case, the case mate tough case, and the carbon fiber samsung case. This one is the best of them all, I am very happy with this case
whoa, that looks like it'd be pretty ****in sweet if they made them 2 tone..
turbosix said:
whoa, that looks like it'd be pretty ****in sweet if they made them 2 tone..
Click to expand...
Click to collapse
http://cgi.ebay.com/Black-Blue-XMat...268389?pt=PDA_Accessories&hash=item5d2b1cd525
Like this?
talltexan said:
http://cgi.ebay.com/Black-Blue-XMat...268389?pt=PDA_Accessories&hash=item5d2b1cd525
Like this?
http://s3.amazonaws.com/daydeal_com/t959_xmartrix_blublk1.jpg[/IG][/QUOTE]
i love you more than you could ever know. :eek:
Click to expand...
Click to collapse
turbosix said:
i love you more than you could ever know.
Click to expand...
Click to collapse
they also have pink and white if your into that just search Xmatrix Vibrant case. They are cheaper than OP's so i dont know if they are the same or not but they do look the same.
I ordered this case on Tuesday and it came today. I am very impressed and the quality is much better then I expected.
Did the one you got off Ebay come with the hole for the mic already cut? Looks in their photos like it's there already.
No i ordered it from fommy and I forgot about the missing mic hole lol.
dashed said:
No i ordered it from fommy and I forgot about the missing mic hole lol.
Click to expand...
Click to collapse
I ordered the blue and black one from fommy on thursday and received it today. Mine has the mic hole already cut out. In my opinion it feels just a little bit loose and kinda cheep. I like the way it looks and is very slim so I'm gonna give it some time to see if it grows on me or if i want something else
The black case I received fits extremely well and is not loose at all.
Great Deal on this Case
I'm getting one from Handhelditems.com found here xmatrix case and it's 10.99 and $2.89 shipping, plus I used coupon code 30vibrantsamsung and got 3.30 (30%) off. Price out the door - $10.54. Helluvuh deal
Got the case today. It sucks.
Sent from my SGH-T959 using XDA App
You guys should try this case too. (Incipio Feather case) I spent like 3 days searching for the perfect case for my captivate (from silicone case to leather pouch) and this one has by far the best quality and look, not to mention about the extreme thinness. Got it this afternoon and fits perfect to the phone and looks great as in the picture. The only draw back is that it doesn't cover the front side, but I can live with that.
I loved that case with my iphone, it's crazy light and thin. The only problem I had on my iphone is all I could get was white and it got nasty dirty in a week, so I would advise against white
Sent from my SGH-I897
samzoferrari said:
You guys should try this case too. (Incipio Feather case) I spent like 3 days searching for the perfect case for my captivate (from silicone case to leather pouch) and this one has by far the best quality and look, not to mention about the extreme thinness. Got it this afternoon and fits perfect to the phone and looks great as in the picture. The only draw back is that it doesn't cover the front side, but I can live with that.
Click to expand...
Click to collapse
Is it made of the soft rubber like material that gathers dust?
it's made of plastic, but looks like it's mixed w/ some sort of rubber or soft material because it's got that little bit of soft touch. (maybe that's why it's more flexible too) So far it doesn't gather any dust like some silicone cases do, but i will have to see more since i just got it today.
i wish they had more colors. Black phones get lost in the void that is my purse.
ladymelody said:
i wish they had more colors. Black phones get lost in the void that is my purse.
Click to expand...
Click to collapse
Ebay captivate incipio and they have the exact same case but in pink (but its called magenta)
From the eBay description: "With a convenient two-part sliding design, the EDGE™ embodies innovative cases focused on accessibility. Simply remove the bottom cap to dock your device in most any docking station for quick and easy charging."
I have a home dock I put the phone in every night. This is the main reason I stopped using a case. How does this design work with the Samsung dock? I can't tell from the pictures and I'm not willing to risk $25 to find out.
Miami_Son said:
From the eBay description: "With a convenient two-part sliding design, the EDGE™ embodies innovative cases focused on accessibility. Simply remove the bottom cap to dock your device in most any docking station for quick and easy charging."
I have a home dock I put the phone in every night. This is the main reason I stopped using a case. How does this design work with the Samsung dock? I can't tell from the pictures and I'm not willing to risk $25 to find out.
Click to expand...
Click to collapse
Not sure if you realize but the EDGE is a different case than the Feather, which is what the OP got. Again, sorry if you knew that. Just thought you might not realize.
fooldog01 said:
Not sure if you realize but the EDGE is a different case than the Feather, which is what the OP got. Again, sorry if you knew that. Just thought you might not realize.
Click to expand...
Click to collapse
I thought so, but the one I was looking at on eBay (that I took that quote from) matched the one in the pic the OP posted.
Just wondering if this slides on like a silicone case or if it clips on like other hard plastic cases, is it hard plastic or like a hard silicone?
Any way you could take a picture, the incipio site doesn't really show anything to great about it?
Does it fit tight?
How does it hook on?
Even though I'm a dude I'm tempted to get the "Magenta" one just to spruce up my phone haha.
Is it hard to get on and off? I need to replace my battery once a day.
The Feather is 1 piece that snaps on, and from the pictures, it looks like it only hugs the corners. The EDGE is a 2 piece snap on case.
*taken from http://www.myincipio.com/
Does anyone have any photos of this case from the top or sides? I can't find any real world or manufacturer pics of that.
that looks nice
it doesn't cover the edges and by the looks of it, it only protects the back and if you place it face down it won't lift the phone off the surface any
It looks nice but it doesn't protect anything. The corners and front have no protection. With my experience when you drop a phone the corners get messed up
I ordered this case for my wife:
http://cgi.ebay.com/SILVER-BLACK-FL...461939?pt=PDA_Accessories&hash=item4156763633
It came in and it fits perfectly, its slightly rubberized feeling so its grippy and its slim. I tested it and it works in a pocket without sticking to the pocket liner.
The nicest thing I like is that the graphics are several layers deep, giving it an interesting depth to it. Ill try to take some pics with my Tbolt of her Tbolt in the case.
Not bad for 6 bucks. The only drawback I noticed but she does not care about is that some of the graphics of the front and back piece do not line up perfectly on the seam.
I also ordered her another similar case but more flowery. Ill post when that comes in.
I bought a solid black one from the same seller. It is a nice case for the price. Looks good and appears to be good quality. Only time will tell if it begins to peel.
Here's a few pictures of the case.
im so torn over whether to use a case on this or not. if it had gorilla glass i wouldnt care.
Being a 2 piece case, how well does it hold together from a fall? If it landed on its edge is it going to pop open?
Hard to tell. I don't want to drop it and test it for obvious reasons.
But it does snap together pretty well and its not terribly easy to open it back up and take it off.
Here are a few pictures of the second case I ordered for her from Amazon. This one looks even better than the other. And it snaps the same, front/back, but it feels a little less sturdy. It does not snap as strongly as the other.
possible to get a pic of the two pieces separately?
how is the power button? easy to push?
Which "finish'' are these cases? I see there are a different ones listed.
bad4u6669 said:
possible to get a pic of the two pieces separately?
how is the power button? easy to push?
Which "finish'' are these cases? I see there are a different ones listed.
Click to expand...
Click to collapse
Here are two pics of the two pieces of the case.
Power button opening is quite large so my entire thumb pad fits well and the button is not obstructed at all.
I have no idea on name for finish, they are rubberized plastic. So they are grippy on the outside and won't slip. But they are smooth plastic on the inside. Also, its not grippy to where it clings to pocket liners, its fine in my jeans and in my khakis and suit for work.
I just need to find one I like for myself now. Maybe something like this:
http://www.amazon.com/HTC-ThunderBolt-Incredible-Rubberized-Shield/dp/B004LSYEC2/ref=pd_rhf_shvl_32
or this:
http://cgi.ebay.com/ABSTRACT-ART-RF-CASE-HTC-THUNDERBOLT-4G-CHARGER-/230598620069
Also, some people praise TPU cases, what s TPU? Plastic or the jelly kind?
man that case on ebay is vibrant! I went for the hard/rubberized case from the same seller. figure if i dont like it or it beaks after a few months im only out 6$
as long as it can stand falling off my lap when i stand up im good.
bad4u6669 said:
man that case on ebay is vibrant! I went for the hard/rubberized case from the same seller. figure if i dont like it or it beaks after a few months im only out 6$
as long as it can stand falling off my lap when i stand up im good.
Click to expand...
Click to collapse
Very nice case indeed
TPU (or Thermoplastic polyurethane) is like silicone, except much sturdier and glossier. http://en.wikipedia.org/wiki/Thermoplastic_polyurethane
I got the shell/holster combo from VZW and I love it. It is slim and grippy.
Ordered my case yesterday. Got it today. That person don't mess around. Damn good case for the price too. I got the rubberized black one. Had to graba Sharpe and mark the inside edges black, cause they were showing white when clipped together.
This thing will stay together for a few falls. Can't beat it for this price.
Sent via bits and bytes
Cool. Can you take some pictures? I went ahead and got the dark red/burgundy one. Ill get the arty/colorful one when it drops in price a tad.
1st complaint
I removed the case for the first time today. I used a penny in the access slot on te side and it chipped away some of the black. I had to use a sharpie to fill it in so it wouldnt be so obvious.
Since a fair few of you will now have one of these, I was just looking to get some thoughts and opinions on one please?
Also I know it can stand vertical with this case on, but can it stand landscape?
Thanks
U can do everything without any trouble, it's a great case.
Sent from my GT-I9100 using XDA Premium
TecQuality said:
U can do everything without any trouble, it's a great case.
Sent from my GT-I9100 using XDA Premium
Click to expand...
Click to collapse
I've seen that it can stand vertical on it's own when the case is on, I was wondering if it could stand landscape too?
Thanks
Sent from my GT-I9100 using Tapatalk
Yeah, it's a great little case. I bought the black one, and i'm looking at getting a blue one next. Really cheap for official ones from Trusted Sellers on ebay (roughly £7 without original packaging, £10 with)
the only downside is it lets dust through the little holes, so you get a neat little dust pattern on the back side of your phone - a regular removal and wipe on your trousers helps.
I've had one on it for about 2 weeks and I like it, only drawback is I had to shave down by USB connector plastic to get it to fit while the case is still on. I ordered another from dealextreme because it was really cheap. I notice the case just touches the mic area but doesnt cover it up. I like it because it's not very bulky and the plastic 'mesh' back fits over a soft case and makes it rigid and easy to hold.
Good luck for u
Got a generic cheap mesh case from eBay, its pretty awesome but as mentioned above, gets a bit dirty after some long time, and mine is cheap enough to start breaking on corners, had a few falls tho, and that's the purpose of a case, so the phone doesn't break instead
I had this case, it was okay at the start but in the end the plastic on the top corner started breaking away. Also the one and only time I dropped my phone with this case on I got a nasty scratch just above the screen where there was no protection. I had to ditch it. I'm using a plain black tpu case now, much more protection. The advantage of the mesh case is that its so slim.
Edit : Oh yea and its a dust magnet.
Got the original mesh case, I dropped it twice since I got it. First time no damage at all, protected the phone nicely. Second time the phone popped out of the case as it hit the floor (shoulder hight, had a nice spin to it also) but both the case and the phone didn't suffer any damage. So I guess it serves it's purpose and looks nice as well.
Aesthetically nice.
Crap if you want proper protection.
I bought it merely to protect the camera and back when I put the phone down to prevent scratching. For overall phone protection it's definitely going to be lacking as the top and bottom edges of the phone aren't covered. The case clips on easily but stays on fairly tightly. The rubbery material gives better grip when holding the phone. Dust does get in over a week or so over the back of the phone, though isn't noticeable with the case on, and can easily be wiped off. I think the case looks pretty nice, all key areas are fully accessible and for the price of about £8 was worth it.
is not compatible for i9100P
I've just buy the genuine Samsung mesh vent case for my Samsung Galaxy S2 win NFC (i9100P) but it is NOT compatible. My colleague on the i9100, not NFC, perfect fit.
Some ideas?
Light, strong and keeps the thinness we all love about our S2s!
Dropped mine a couple of times on to wooden floors and no damage yet
Protects the camera lens too when lying on a flat surface
The dust comments are true but only noticeable when u take the cover off so no big deal and it fits so snugly it kinda looks part of the phone!
To answer original question tho, no only stands in portrait
I got an official Samsung one given with mine. Good at protecting from scuffs when it's on a table or desk but wouldn't like to trust it with protecting my phone from a fall.
That's why it's sat unused in a cupboard at work! If anyone wants it just message me and I'll stick in the post.
Andrewawright said:
I got an official Samsung one given with mine. Good at protecting from scuffs when it's on a table or desk but wouldn't like to trust it with protecting my phone from a fall.
That's why it's sat unused in a cupboard at work! If anyone wants it just message me and I'll stick in the post.
Click to expand...
Click to collapse
I'll take the case if it's on offer, let me know your thoughts on shipping to Australia Figure you sent all your convicts here, so a case shouldn't be a problem
Just came across a review for the Khomo Back Cover
Interesting...
Sent from my SGH-T999 using xda premium
Maybe...
Maybe this is what I have been looking for. Now I just have to find somewhere that can ship it to Sweden for a reasonable price.
Any tips?
I would so buy this if that logo isnt there. lol
^Yeah. Logo ruins this.
Xcor3 said:
I would so buy this if that logo isnt there. lol
Click to expand...
Click to collapse
One major flaw, it leaves the camera lens exposed so that it can be scratched every time you put your phone down. Would need a quick Sugru mod.
It looks like you could rub the logo off
i bought this on amazon for $6.99 its not bad. was kinda my last resort as i was looking for something to match my pebble blue but theres nothing out there that did so i went for utility. its definitely has more grip than OEM but not by much. its a soft touch type material. fits just like an oem though. more rigid too
Beako said:
It looks like you could rub the logo off
Click to expand...
Click to collapse
can,t already tried. i might try a sugar cube though(throwback to the RAZR days)
angie4u said:
looks nice but the material looks like it will attract dust like crazy.
Click to expand...
Click to collapse
it attracts more scratches(superficial can be wiped away) than dust
Got my back in... Love it, minus the damn khomo across the bottom, it's perfect for me
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
Manufacturers need to make more of an effort if they insist on stamping their logos on the back of their parts? Especially when the logo looks like it was designed in about 3 minutes by a 12 year old....
O.P! Check out my camera mod! Hope this can be useful with your rubberized cover.
http://forum.xda-developers.com/showthread.php?t=1862307
Got the same battery cover myself. It doesn't provide more grip in all situations, but definitely provides more "feel" and less slippery than the original one as it's not gloss. What I mean by all situations is that most of the time I don't have a problem gripping the original gloss back, but it definitely becomes harder to grip (slippery) when my hands are too dry or have a little dust/dirt on them.
Every review and picture I've seen of this case has it fitting perfectly and snuggly like the Samsung original battery cover. However, mine is a little bit off. Seems the tolerance on the tabs are just a bit off and won't fit completely on my S3. Some of the corners won't 'snap' to latch and there's a noticeable gap along the edge. Doesn't feel like it will fall off but you can see it. I ordered through Amazon and will be returning this one to them. I did order the exact same case again from Amazon to see if the tolerance on that one is any better. If it fits well, I am definitely keeping it.
The case makes the phone feel more solid. There is no give/bending/etc on it at all when pressing along the back. Again the biggest complaint is the company logo. I've remedied this somewhat by darkening the logo with some flat black paint. I used a paint pen so it was pretty simple to do without it bleeding onto the rubberized part. You could probably do the same with a Sharpie to make the logo stand out less.
Would be really sweet to get my hands on 2 covers. Any tips on how to buy them or getting them transported to sweden?
Many thanks!
looks good