Flashing from SD Card - Touch Pro2, Tilt 2 Windows Mobile General

I have a Touch Pro2 (GSM) with energy 6.5.5 rom. I wanted to install a new rom.
OK I formatted my SD Card, backed up all my contacts with myphone.
I downloaded my desired rom, renamed it, put it onto my SD Card.
I removed the sd card and my sim card.
I used http://forum.xda-developers.com/showthread.php?t=649191 this to format the main os. Phone restarted with just "touch pro 2" on the display.
I removed the battery, inserted the SD card (with the correct named rom).
I inserted the battery again and started the phone while pressing the lower volume button.
The red green blue white screen from my bootloader opened up. AT the top it says
RHOD00 32M SS-BC
SPL-0.85.OliNex
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
... .... ... (some numbers) calibrated
and in the white area it just says Serial. Nothing happens. Is it safe to take out the battery and try to install the image with active sync??

Did you reformat sd card FAT32?
Did you install Hard SPL 1st?
Also, I have found on occasion, the transfer to the sd card isn't good, copy the .nbh file over again and try if you have done the 1st 2 things....

ultramag69 said:
Did you reformat sd card FAT32?
Did you install Hard SPL 1st?
Also, I have found on occasion, the transfer to the sd card isn't good, copy the .nbh file over again and try if you have done the 1st 2 things....
Click to expand...
Click to collapse
Thanks! I already had hard spl. As I said, I was using a custom 6.5.5 rom before
I didn't have any access to the SD card because I don't have a card reader for micro sd (that's why I copied the file before I removed the sd from my phone)..
But I was able to get around the situation. The moment I plugged in the usb cable I was able to access the phone via active sync and I could flash it from within windows

PumpAction said:
I used http://forum.xda-developers.com/showthread.php?t=649191 this to format the main os. Phone restarted with just "touch pro 2" on the display.
Click to expand...
Click to collapse
why did you do that?
also did you rename the rom to RHODIMG.nbh?

Because after I went from stock 6.1 to stock 6.5 rom suddenly the coreplayer and windows media player were suttering at ALL videos that worked perfectly fine before. I then tried an enegry rom.while it was good looking it made no difference in video playback.thats why I wanted to switch to another 6.5 rom that was using 2.1 manila instead of 2.5.
and yes i named that rom exactly like that! One last question. After having successfully hard spled the phone, is it now safe to install every rom i want without having the fear to brick my phone?
oh and btw. while the new rom really AMAZING videos still stutter 3d games work perfect but that damn videos not. and on a small note:the newest opera 10 mobile is INCREDIBLY fast!Finally a piece of software where I can see how fast the cpu really can be just flash is missing

Related

Strange SD card Problem

I have been using Touch 4.02 with an 8gb card for ages now with no troubles then yesterday the storage card is no longer recognised by the phone? I tried the usual soft reset, taking the card out wiping it put it back in still no joy.
Reinstalled the sdhc cab file didnt work, Have just re-flashed with the new diamond look a like rom and still it aint recognising the card.
Has anyone got any ideas??
mikehulme1983 said:
I have been using Touch 4.02 with an 8gb card for ages now with no troubles then yesterday the storage card is no longer recognised by the phone? I tried the usual soft reset, taking the card out wiping it put it back in still no joy.
Reinstalled the sdhc cab file didnt work, Have just re-flashed with the new diamond look a like rom and still it aint recognising the card.
Has anyone got any ideas??
Click to expand...
Click to collapse
Probably your card is broken....
Try to insert it in a card reader and see if it recognizes the card....
Yeh will have to wait till I get home not sure my memory card supports SDHC though?
I have a similar problem, and like you I've been happily using an 8gb card for a while, but in the last week it has stopped working correctly.
Occasionally it is fine, but most of the time access to the card is either very slow or it doesn't appear at all.
I've tried the following but with no success:
- Using another MicroSD card (2gb)
- Reading the cards in a card reader and they are fine
- Reinstalling Artemis Touch 4.02 WM6.1
- Formatting the card (FAT32)
- Shimming the MicroSD card with bits of cardboard as I've read there can be a loose fit
- Cleaning the contacts on the card reader
- Pulling the contact pins out a bit to get a better fit
Does anyone have any ideas of anything else to try?
Does WM5torage work?
I did the followings to make my 4GB Micro SD usable by my Artemis:
1-flashed it to FAT32 in my laptop (I Had to format my laptop partition D of my HDD to FAT32 to make the microSD recognizable by my NTFS system).
2-copied the "system folder" from my older 512 MGB card as it is (hidden) to the root of my 4GB
3-The 4GB is readable by my artemis by now.
4-To make sure the crad will be working good in the future, I installed the "Flashcard" Cab in my Artemis and reflashed the card to FAT32, 512 Bytes 4KB clusters.
The card is just fine under Artemis windows, but I gatta take it out when flashing any new ROMs or Radio.
Hope that'd help you.
uniqueboy said:
Does WM5torage work?
Click to expand...
Click to collapse
No - WM5torage behaves the same ... i.e. occasionally works (if the phone can see the card), but most of the time it just reports an error
It is deffothe memory card just put my old 2gb back in the phone and it worked, I have tried the 8gb in my PC card reader and in y camcorder that takes sdhc and neither recognised it.
This explains why my phone started goin so slow it would take ages to do anything then the memory card was unrecognised a few days later.
Im guessing there is no way to repair these?
If you can't read it, you can't do anything...
R.I.P.... :|
Cheers
Gutted oh well
not as gutted as i am ... looks like i'll have to buy a new phone!
Just try to format it by these criteria
FAT32, 512 Bytes 4KB clusters
then let us know.
dude dont panic try to recover the card first before you format it. i am sure there are some imp data there eh?
use a disk recovery utility on ur pc
my best choice is Recover My Files http://www.recovermyfiles.com/
if you are using windows os also try to run scan disk
use pocket mechanic then on ur ppc
let us know how well u do
Sorry for posting...Wrong thread...

Hard Reset caused...

Hi All, I did a hard reset today on my phone and ever since the call buttons have changed.
I have some bad pictures of what has happened but I tried to reset it another 2 times after it went like this and it didn't correct the problem.
Does anyone have any ideas? Maybe editing the registry?
Its like the buttons don't have the 3d stand out effect but its as if they are pushed in if you get me?
I just wanted to add that I have tried changing themes and the problem still exists.
Which ROM are you using?
The Rom is 2.15.502.3
I havent been able to update using the usb or micro sd method so I am stuck with the old rom
Did you have Hard SPL V7 installed on your Hemes?
Did you format the sd card fat32 and was it 2Gb or less?
Did you rename the .nbh file to Hermimg.nbh?
These 3 things are the major reasons the sd card method fails....
Go to page 116, post 1160 of this thread to use the sd card method to install Hard sPL - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...
I did all of those
It just gets stuck on the tri color screen.
Thanks
At bootloader (tri-colour screen), whats the SPL?
Also, I can't say this enough, make sure that the sd card has been formatted FAT32 . Best if done in a card reader through windows, not through the phone.
I've had people swear that they had and then posted later that it was only formatted FAT.
Double check that the .nbh file has been renamed hermimg.nbh too.
These are little things but will screw up any effort to flash.
Cheers...
What device
what device are you using?
if not supercid then cid must match rom when you flash?
read this again
xooku, thats why we install Hard SPL.... It effectively superCIDs your Hermes. If you have it, it doesn't matter what CID you had previously..
Cheers...
I have done all this countlessly, It still goes to the Tri Colour screen, Says loading.. for a split second and then it goes back to the tri colour screen.
Does the card have to be completly erased apart from the hermimg file?
robiscool said:
I have done all this countlessly, It still goes to the Tri Colour screen, Says loading.. for a split second and then it goes back to the tri colour screen.
Does the card have to be completly erased apart from the hermimg file?
Click to expand...
Click to collapse
yes completely format the card first. Then load the card with the HERMIMG.nbh and flash. Let us know if it works.
It would be if you had formatted it FAT32 just before flashing... Back it up 1st though.

Some Newb Questions

Okay first off im gana start off saying sorry im a complete newb and jsut got my first WM phone the other day i got the Verizon VX6900 and i wana upgrade to WM 6.5. Ive read over cody bear's FAQ for NFSFAN's rom several times and although im kinda scared to screw it up hopefully i wont brick my fone. my first question is i know you suppose to upgrade you radio first but especially since mine is 1.60.30 no where near 3.42.50. So can someone point me to a how to do it and do i have to get a verizon one because i saw a file to upgrade for Bell's radio and im not sure if thats the same.
Also can everyone put my fears to rest that im gana destroy my fone when i reflash it. It dosnt seem that hard im just kinda nervous.
Sorry again for being newb and making a thread there is just so much information and its hard to figure it all out without someone guiding you in the right direction
First you need to unlock your phone using the cokeman unlocker.
From there, if you have the SD card that came with your phone (the 512MB one). YOu can download a radio upgrade that changes nothing but the radio on your phone. This is a good idea as verizon can be tricky.
http://forum.ppcgeeks.com/showpost.php?p=389964&postcount=8
That file has the radio flash in it.
So to install it, you first make sure your phone is unlocked. Then copy the file from inside that zip to the SD CARD (note: the sd card must be formatted FAT32). Then enter bootloader mode by pressing holding down the power and camera buttons while pressing the reset button with the stylus. Do not have a USB cable plugged in. WHen the boot loader loads up it should be a tricolor screen that says COkeman unlocker or bootloader ver 2.41 or something like that. It will say serial at the bottom and after a few seconds ask you if you want to install the rom. If it asks you to confirm do what it says to confirm. IT shoudl flash then restart. When it restarts check the red text at the bottom and see if it says 3.42.50 next to r. If so you properly flashed your radio.
From there you can install ANY upgaded rom you like.
okay thanks i dont have the 512mb sd card i only have a 2gb sd card will that work?
As long as it is a regular microSD, not microSDHC. It should say so on the card. Mine 8GB card says microSDHC on the card itself. More than likely the card is standard SD (as I think SDHC doesn't start until 4GB).
So the requirements for flashing from the card are:
I think you need to have the device unlocked
microSD Card (NOT microSDHC)
Card has to be formatted FAT32
The file must be named VOGUIMG.nbh
No USB cables plugged in.
ok so im getting a little nervous i unlocked it and then flashed the radio update and it installed and says update complete update success but its not restarting do i have to restart it. did i just brick my phone?
Hard reset it yourself.
well i managed to get it to work and installed NFSFANs 6.5 rom and it runs amazing. i installed the vzw mms cab but i still cant get my MMS to work
nickbutterz said:
well i managed to get it to work and installed NFSFANs 6.5 rom and it runs amazing. i installed the vzw mms cab but i still cant get my MMS to work
Click to expand...
Click to collapse
Read the FAQ for that ROM over on this thread HERE all your issues with MMS, GPS, ETC can be found there
Detroit Doug
Detroit_Doug said:
Read the FAQ for that ROM over on this thread HERE all your issues with MMS, GPS, ETC can be found there
Detroit Doug
Click to expand...
Click to collapse
thanks man got mms working now just gata start working on the GPS. hrm just wondering if anyone else has this problem sometimes when i accidently click the persons name in the SMS thread the fone just freezes
Sorry, I'm another noob when it comes to flashing roms as well. Once you flash from the microsd, will the new rom be compatible with a microsdhc after its upgraded? Or can I only use Microsd from here on out??
Thanks for the help.
No problem. The only time you NEED a standard microsd card is when you are flashing a file to the device. To be exact, when you are upgrading the radio as all of the ones I have seen load from the microSD card, otherwise all of the custom roms can be upgraded over USB. The reason you need a standard microSD card to flash from the SD Card is that microSDHC requires a specific driver to be loaded and at the bootloader point that driver has not been loaded. This means at the boot loader point, the port can only funciton as a microSD port. Once the OS has loaded, the driver has been loaded as well, therefore it can read both times.

Flashing via SD card assistance

I've got a Tilt 2 with hard spl and can flash from my desktop no problem. I'd like to get the flashing via SD card going, but it's hanging.
I've got the nbh file copied to the root of my SD card, get the phone into bootloader, but I see a message flash up about no image. It's very quick though and then the phone hangs in the bootloader. A soft reset fixes it and the phone boots up.
I'm clearly missing something and can't figure out for the life of me what it is.
The image file is named correctly. It was copied to the phone through WMDC to the SD card. Should I put the phone into disk mode a copy the image over?
The SD card is formated in Fat 32.
Any thoughts/Advise?
Thanks.
maybe..
i had this issue before - check your .nbh file with total commander, or put it in your pc and check it. if you name it .nbh with the wm file explorer, it actually ends up RHODIMG.nbh.nbh - solution is just to remove one .nbh!
:::Whimper:::
I'm having this exact same problem!
My RHODIMG file is named correctly and in the root directory (there is nothing else on the SD card either), but I get that same EXTREMELY BRIEF message about no IMG file and then it hangs at the bootloader screen with 'Serial' in the white box on the bottom.
I've even tried using Mobile Flasher, but nothing is working. I
What am I missing??? I've tried it many times already, formatted my card a few times and loaded the RHODIMG file again, but nothing! My Rhodium will NOT connect via USB anymore, so I need to flash via SD card.
Help!
Debbie
I actually don't even rename the file, it's already got that name from the rom. It's e2 manilla 2.5 rom.
I'll try and transfer the file to the card when the phone in disk mode and see if that makes a difference...
O-M-G(!), this is *so* freakin' wacky!!!
I just switched SD cards to one that was larger (8GB rather than the 2GB), that had tons of stuff on it, then copied the RHODIMG file in the root, and then ran 'enablerapinew.cab' again, just for the hell of it...
Damned device found the RHODIMG file there from the bootloader and the update ran as expected, but not on the 2GB card with nothing else on it! WTH?!
Device says that the update is complete, so I'm booting up now and will do a few resets and then perform the tedious task of setting up my Tilt 2, etc.
Don't know whether the cab (thought I only had to run this once when Hard SPLing?) or the different card was what caused it to work, but I hope this helps someone else with the same problem. Whew!
Debbie
...Who's back in business!
SOLVED!
I don't know what caused the magic, but I was able to flash from SD card... FINALLY!
Here's what I did: Flashing Via SD Card Assistance
Hope this helps others!
Debbie
No, this did not work for me. I tried installing the cab again, but no luck, just passes on by saying no image.
Delete image off sd card, reformat FAT32 and copy image back on... I have had this problem myself, it seems that when the .nbh file copies it doesn't register on the card properly or something. Either deleting the file then re-copying seems to work but I still like to reformat too..... DON'T just copy over the top of the image file... THIS DOESN'T WORK... leads to a lot of hair pulling frustration...
Cheers...
So I tried a reformat of the card, just a quick one, not full. Still didn't work. I downloaded another image to try out, the lastest Energy rom, to flash on a completely blank card. That didn't work.
So, I went and got an older card, 8 gig, that is currently being used in a camera. The one I use now is a 16 gig card. This one worked fine.
Conclusions being perhaps a 16 gig card won't work for flashing?
brands
i have heard of certain brands having sizes that didn't work for flashing, for whatever reason. It was a long time ago on my kaiser, so i don't remember which it was, but kingston 2gb comes to mind. like i said, don't know if that is accurate, but there definitely were some that just wouldn't work. perhaps a different brand 16gb?
Well, I used the other memory stick, a Scandisk and this worked fine. Must be something with the 16 gig Kingston disk as it just will not work.

[Q] Weird problem with SD card!

Hello,
friend got her hands on a htc desire. She let some small shop unlock it before really testing it. Now we got the following problem:
The SD Card doesnt work. At first everything seemed to work okay. She took 52 pictures, even installed on app on the sd card. Then it basically froze.
We can delete half of the pictures and make some new ones. After the phone is rebooted all pictures are gone. Apps cannot be installed on the sd card.
If I remove the sd card and put it in my Nexus One everything works fine. New pictures survive the reboot, old ones get deleted.
When she puts the sd card in her desire, everything is back to 52 pictures and 1 app on it.
You cannot copy stuff like update.zip on the sd card, because the phone will only notice 52 pictures on it... Rom Manager has a "fix" option which doesnt work and partition it didnt help it - if it did anything at all.
We even bought a new 8 gb one, same problem. Some other people reported the same problem in forums, but there is never an answers what did fix it.
Its S-OFF with AlphaRev.
Sadly we both have no idea how to fix it and no android development skills. My plan would be to go back to RUU to see if the problem is still there. If yes, just get a new one from HTC. If no, unlock it again.
Sadly when it comes to roms and the "simple guides" we fail to reproduce even the first steps. "Go to fastboot and enter command XYZ" - yet we cannot enter any commands there.
Any help is welcome.
Can you connect your phone to pc in adb mode? Or simpler: what happened when you are connecting your phone to pc? Does it ask about mass storage mount? Is it in debug mode? If not, I think that it is classical USB-Brick, else... I don't know what is wrong...
I had also a problem with my sd-card.
Put it in a card reader and make checkdisk with windows solved my problem.
Weird, my answer disappeared.
When we connect it to a pc, we can delete files, format it, run scandisk, copy stuff on it. Everything works fine. When we put it back into the phone, the old 52 pictures and nothing else is on it.
And I thought I was the only one…
My problem is as follows, I had with my 1st Desire a 8gig Class 4 Transcend SD card which was perfect and connecting to and from my home and work pc was effortless.
Then my Motherboard burnt out on that phone sent it back and when I got the new one I put my 4gig Class 2 SD which I got with the phone back in and no issues.
A few days later I bought a new 8gig Kingston Class 4 SD ( I lost my Transcend SD card) and after 2 days I would get “SD mounted as read only” so formatted the SD copied my data back to my 8gig Kingston card which worked fine on my PC but the same problem persisted when I put it back in my phone. I was using ADW launcher and kept getting the same errors all the time, then I switched to Launcher Pro and since then I have had no SD card problems.
Also when I was using standard HTC sense I also never had a problem, I hope this is of some help.
I rooted my htc desire using Unrevok 3 and also tried to partition sd by mini tool home version . unfortunately after partition i cannot access or recognize sd in my desire.
Still not making any progress, ..

Categories

Resources