Verizon 6900 No internet - Touch CDMA Windows Mobile ROM Development

I have a verizon 6900 that I updated using NFSFAN's WM6.5 1.00 FINAL ROM and now I cannot get the internet to work. I went back to the factory 6.1 and was unable to even make calls, so I spoke with verizon and got the phone working but they were unable to get the internet working. I flashed the ROM with the WM6.5 1.00 again and ran a couple different provisions and I still cannot get the internet. Can someone please help.

Sorry it keeps asking for username and password.

internet
VZW can tell you the user name and password its something simple like vzw3g or something. If you have that setup correctly you may be in the same boat im in. I can not connect to the internet. I did a hard reset some time back and lost the ability to data connect. I contacted the vzw techies who could not solve the problem, went into the store who could not solve the problem, went back to the "techs" on the phone who could not solve the problem. They all said it was my software which I think is bs. The problem is not my software because my phone tries to connect to their network and I have no known software issues. It has to be on the network end where the network wont recognize my phone. I quit working on the problem because I dont use data right now anyways and was on a pay as you go data plan so it was vzw's financial loss that i can not use data.

This fixed my Verizon Phone
1) dial ##778, enter in 000000 for the password
2) copy the ESN(Hex) Exactly how it is(you need the caps)
3) click View Info in the lower left corner and click M.IP Settings
4) Change MIP_MODE to Simple IP Only
5) Click View Info again and goto Security
6a) HDR AN AUTH User Id = [email protected] (fill the 5's with your 10-digit number)
6b) HDR AN AUTH Password = (Your ESN(Hex) With CAPS)
6c) PPP USER ID = [email protected] (Same as above)
6d) PPP PASSWORD = vzw
I left DUN log on blank
Change settings under
7) Click OK in the top right corner and save and reboot.
Goto Start->Settings->Connections->Connections
9) Click Manage existing connections
10) Select Alltel Wireless and click Edit...
11) Click Next in the lower right cornder until you get to the user name and password screen
12a) Username is [email protected] (Same as above)
12b) Password is vzw
13) Click Finish in the lower right corner
14) Enjoy verizon wireless internet!
Also make sure you update your PRL to an verizon one.
Go to M.IP Default Profile.
Enable Profile: Enable
NAI: [email protected]
DUN NAI: leave blank

But know I cannot update my radio. This has been an issue since I unlocked my phone. I cannot get the bootloader to load from my 1 GB microSD. I am not sure what to do. XV 6900

I have had this problem for months now.I have tried everything possible. Called vzw i dunno how many time I dunno how many new A-keys I have had.I even tried these settings. Nothing seems to be workn.But who knows. Only way I can get internet on this phone is to manullay put my phone in 1x. which is way slow but it works

I got everything working great now. I ran the .40 unlocker and then flashed back to the factory ROM from HTC. I entered all of the setting back into the phone that I listed above and then flashed it again with the factory ROM. All of this put my phone back to factory. I then re flashed it with the 2.31 and was able to update radio and flash with the 6.5 ROM from SD card in phone.

Related

O2 XDA Orbit UK with Voda SIM - GPRS Problem

Hi All,
Am sure there are many threads - did a search but came up with nothing like mine. O2 Branded XDA Orbit with Vodafone SIM.
Upgraded from Default ROM to WM6 Bepe version - everything seems fine except my GPRS Connection.
CE OS 5.2.1238 (Build 17745.0.2.3)
Rom 3.4.207.1 WWE
4/18/07
Radio 2.49.90
Protocol 4.1.13.25
Model ARTE200
I have tried connecting to GPRS using my VODA SIM - which I know for a fact IS enabled for it as I was using it on my XDA-IIs - Now I just cannot connect to the GPRS to access my gmail or anything whatsoever.
I entered all the details for Voda-GPRS manually and also from CAB from this site and still cannot connect - it starts to connect and says the "connection was disconected" check settings...!!!
I am at my wits end on what the problem is !
Any ideas?
Dev
A couple of months ago I had an HTC Beta of WW6 and had to wipe it as it would not connect, same as you. Afterwards, I found out that WW6 install resets varions Connections settings incorrectly (part of beta).
Go to Settings / GPRS settings and make sure you have CHAP selected
My install had PAP selected.
Jeff
Sounds to me like the rom you have used has a feature/setting that disconnects GPRS connections for whatever reason - possibly to stop programs from auto connecting with GPRS.
Have you checked with the creator of the ROM to see if anything like this was implemented in to it? It may be fixable with a registry tweak or setting.
Mine worked both Bepe and B&B V2 ok.
GPRS:
1. Click on Start > Settings > Connections tab > Connections
2. Under the heading 'My Work Network', click on 'Add a new modem
connection'
3. The settings you require are:
4. Name = Vodafone MMS
5. Modem = Cellular Line (GPRS)
6. Click 'Next'
7. Access Point Name = wap.vodafone.co.uk
8. Click 'Next'
9. Username = wap
10. Password = wap
11. (leave the Domain field blank)
12. Click 'Finish'
Thanks Guys - Worked fine - Seems I was giving the APN wrong...
Well finally atleast it's working now...
Now only to get the Blackberry connect to work and I'm on cloud nine !!!
Hi I was trying to set my dad up with my old wizard.
He's on vodaphone and I've been able to get the GPRS working using the above settings (I also had to add a proxy server of 212.183.137 - type - HTTP port 8799) but IE is now browsing the internet.
However when I try to connect to a imap mail account it just says connecting, then says failed to connect, check settings.
Does anyone with a vodafone account know if you're able to connect to a personal mail server?
Are there any more specific proxy settings?
(start -> settings -> connections -> manage exsiting connections -> proxy settings ->advanced)
Or any advice from someone who's been able to get this working.
Cheers
Matt
All Carrier UK Settings
I downloaded this from the HTC Site - It has the settings for all carriers...Maybe this will help.
Thanks tried this, but it has an APN of internet and these settings always give me the
'answering modem has disconnected error'
I used to get the sae error and then I called up Vodafone and told them. They reset the SIM from their side and things started working fine.
OK thanks for that. I'll just hand it over to my dad with GPRS working and see if he can get his sim card reset.
Cheers
Matt

Internet now working on Sprint Touch w/new ROM

I hope starting a new thread is the way to go on this...
I just updated to the new Sprint Official WM 6.1 ROM, and immediately could not connect to the internet.
I tried running the IOTA automatic data provisioning update (Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start) and it failed repeatedly with a 1012 error. As was posted by others, I noticed that there was a "CurrentUserName" setting in Start->Settings->System->Device Information that had [email protected] where I would have expected to see [email protected] instead. (that would have been my Sprint provided email address) The first thing I tried was to go to the phone dialpad and dial ##3282# to start the EPST program and check my data provisioning settings (this requires that you know your MSL - Master Service Lock Code - if you are going to edit). UserName was blank there, so I tapped the blank setting and held down until an "EDIT" menu popped up. I tapped "EDIT" and changed it to the previously correct [email protected] value. After saving changes and another reboot, I still could not connect to the internet, run IOTA, and the "CurrentUserName" was still wrong. After searching through various settings looking for a way to change the currentusername, I installed PHM Registry Editor and searched again.
In HKEY_LOCAL_MACHINE/Software/OEM/DIM there is a key "EnableCurrentUserName" and it was set to 1. I edited that and set it to 0, exited the Registry Editor, and restarted the device by holding the power button until it warned me about shutting down. I tapped "Yes" and it shut down and restarted. The "CurrentUserName" setting no longer appeared in the Device Information page. At this point I was able to run IOTA successfully and imediately after that I could use the internet and other data services.
I hope this helps someone. Sorry to be so long winded, but I was trying to answer as many "How? Where?" questions as I could as I went.
Briefly:
1. Using WM Registry Editor software, change HKLM/Software/OEM/DIM/"EnableCurrentUserName" from 1 to 0 then save changes and exit editor.
2. Dial ##3282# and edit UserName to correct [email protected] address. Device will reboot when you exit and save changes.
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Thanks to all the others here who have helped me along the way,
Scruffy
anyone else know if this works?
i just flashed the new sprint rom and now the data connection does not work.. no internet.. ? I was just wondering if anyone else had this problem and does this fix it?
After some more time with this ROM installed I have found that it is not neccessary to change the ##DATA# (##3282#) user name settings. Just change the HKEY_LOCAL_MACHINE/Software/OEM/DIM/EnableCurrentUserName value to zero, save changes and then you can run the IOTA update successfully (or at least I can).
I have found that I need to do this every time I do a hard reset of my device. I hope this helps someone else.
Scruffy
this did not work for me.. I Get error code 67
i started a new thread here........ http://forum.xda-developers.com/showthread.php?t=415666
so maybe someone will chime in... the ##3282# does not work for me at all.. you hit that on the dial pad and nothing happens... so i can not access that menu...
For now i went back to a OEM rom and called sprint and they got me working by doing a MASTER RESET... also ##3282# works on OEM roms but i think the file EPST.EXE is missing from the CUSTOM roms... any input would be great..
Not working for me.
i'm sure a master reset from within #778 or whatever would work but i don't feel like
putting in the data again.
Scruffy said:
I hope starting a new thread is the way to go on this...
I just updated to the new Sprint Official WM 6.1 ROM, and immediately could not connect to the internet.
I tried running the IOTA automatic data provisioning update (Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start) and it failed repeatedly with a 1012 error. As was posted by others, I noticed that there was a "CurrentUserName" setting in Start->Settings->System->Device Information that had [email protected] where I would have expected to see [email protected] instead. (that would have been my Sprint provided email address) The first thing I tried was to go to the phone dialpad and dial ##3282# to start the EPST program and check my data provisioning settings (this requires that you know your MSL - Master Service Lock Code - if you are going to edit). UserName was blank there, so I tapped the blank setting and held down until an "EDIT" menu popped up. I tapped "EDIT" and changed it to the previously correct [email protected] value. After saving changes and another reboot, I still could not connect to the internet, run IOTA, and the "CurrentUserName" was still wrong. After searching through various settings looking for a way to change the currentusername, I installed PHM Registry Editor and searched again.
In HKEY_LOCAL_MACHINE/Software/OEM/DIM there is a key "EnableCurrentUserName" and it was set to 1. I edited that and set it to 0, exited the Registry Editor, and restarted the device by holding the power button until it warned me about shutting down. I tapped "Yes" and it shut down and restarted. The "CurrentUserName" setting no longer appeared in the Device Information page. At this point I was able to run IOTA successfully and imediately after that I could use the internet and other data services.
I hope this helps someone. Sorry to be so long winded, but I was trying to answer as many "How? Where?" questions as I could as I went.
Briefly:
1. Using WM Registry Editor software, change HKLM/Software/OEM/DIM/"EnableCurrentUserName" from 1 to 0 then save changes and exit editor.
2. Dial ##3282# and edit UserName to correct [email protected] address. Device will reboot when you exit and save changes.
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Thanks to all the others here who have helped me along the way,
Scruffy
Click to expand...
Click to collapse
how do i find [email protected] where would that be?
Scruffy said:
3. Run IOTA by going to Start->Settings->Personal Tab->Phone->Services Tab->Internet->Get Settings->Start
Click to expand...
Click to collapse
I just upgraded to NFSFAN's latest ROM, everything went well but I can not get my internet to work. The one thing I did notice is under the services tab, internet is not an option. I loaded the dcd sprint carrier 20090714 cab am I missing something else?
Thank you for any help you can provide.
Update:
Well I went back and flashed to the HTC 6.1 rom, then back to the 6.5 rom. That fixed my internet issues, but that option is still missing for me. Then after all of that my MSID was really screwed up. Everything seems to be good now.
please please help me clear the instructions
i have a horribly vague idea of what i need to do, to get the internet working again.
i already got the IOTA_1120 zip file in my cell but when i even try to open it up it says that there is no application that is related to to it, so i must start this application and open up the file from within. How do i do this? am I even doing what im supposed to??
Where exactly is HKEY_LOCAL_MACHINE/Software/OEM/DIM and how do i get there???
if you could please instruct me with simple stieps i would greatly appreciate it, simple being like start>program files> etc.
please help i am one step away from smashing this damm cell into the wall
electricfeel_2012 said:
i have a horribly vague idea of what i need to do, to get the internet working again.
i already got the IOTA_1120 zip file in my cell but when i even try to open it up it says that there is no application that is related to to it, so i must start this application and open up the file from within. How do i do this? am I even doing what im supposed to??
Where exactly is HKEY_LOCAL_MACHINE/Software/OEM/DIM and how do i get there???
if you could please instruct me with simple stieps i would greatly appreciate it, simple being like start>program files> etc.
please help i am one step away from smashing this damm cell into the wall
Click to expand...
Click to collapse
The path of HKEY.... is actually on the registry. You need to use a registry editor (like PHM Regedit) to make the necessary changes to the registry. I would recommend you to re-read those instructions as they will not get any easier than that. Alternatively, if you are on Sprint's official rom and have absolutely no clue what you are doing, you can always call them and ask them for help.
As far as the IOTA zip file, if you cannot open it, that means that you do not have any program to extract from compressed files in your device. Your best bet is to transfer the file to the desktop and extract it there. Once you are done, place the extracted contents back in the device and run it in there.

Internet not working on flashed alltel TOUCH, Need Help

Hey guys, im new to this forum and im having some issues, i recentley flashed my Alltel HTC TOUCH to Cricket, got the full flash but still not abel to get on the web, i do have the right plan and i already took it back to were it got flashed, and the guys there still cant get it to work. can anyone help me with this. And if your from the 915 El Paso Tx, that would be great, Thanks
Yo i'm from 915...i can help you since i haved flashed my own phone 8)
First off can you give details about the phone.
What ROM did they install? Look in the Device information under settings/system
When you dial ##778# or ##778 and you click view....In MIP settings what does it show?
Alletl 6900 HTC TOUCH purchased new 01-05-08,
DEVICE INFORMATION
ROM Version: 3.37.NO2.200
ROM Date: 04/09/08
Radio Version: 3.37.10
Protocol Version: DCAAXAM-4350H
Hardware Version: 0001
PRL: 01014
PRI Version: 2.01_011
Browser Version: MSIE 6.0
M.I.P Setting
# of Profiles: 1
Active User Profile Inde: 1
MIP_ MODE: Simple IP Only
MIP Reg. Retire: 1
MIP Reg. Retry: 2000 ms
MIP Pre-Reg. Ti: 30
Mobile Node_ha Auther: Disable
Send a Reg. Re: Enable
Dormant Handoff Optin: Disable
Are you able to *228 and have it program successfully?
The settings look correct. What does the internet exactly say when you try to connect to the net?
wrong password or login
hey bro. should i change the plan that does not have internet and change it back, and also can you do esn swaps on My Cricket account online.
Is your phone also an Alltel HTC TOUCH
Hmmm
1. check your settings/connections/connections
and make sure everything in there is set-up for cricket. Also once in connections make sure in the advanced tab....both drop down menu's say cricket.
Start\Settings\Connections\Connections Under the General Tab Enter Cricket. Under the Modem Tab put in Cricket Mobile Web select modem to cellular line. Click next put in #777 to dial to Cricket, click next… User Name: [email protected] Password: cricket Domain: Leave Blank, click finish…under proxy settings, check these 2 boxes (this network connects to the internet, and this network uses a proxy server to connect to the internet) Proxy Server: wap.mycricket.com click advanced. The only thing with a value should be HTTP wap.mycricket.com:8080 the rest blank. Click ok and ok again, this ok should bring you back to the connections screen at the bottom click advanced. Click select networks. Under both drop downs select Cricket. Click Ok Go into Exceptions Click add new URL for each of the following settings you are going to need to click add new url again, these don’t all go under one “Add new URL” Block
*mms.mycricket.com/servlets/mms
*.mms.mycricket.com/servlets/mms
*mycricket.com/
*.mycricket.com/
*.mms.mycricket.com/
*mms.mycricket.com/
2. I have a sprint touch and it doesn't really matter alongs its a touch.
3. No i cannot do esn swaps for you but my advice would be to check the connections settings first and if that is correct call customer service and have them reset your account.
what do you mean by resetting my account
Its just as if they are refeshing/resetting your account which ever term you want to use.
I edit my previous post....follow those directions to make sure your connection settings are correct.

How exactly can i do this?

I used to be with AT&T with my 8525 and then switch to Sprint which of course doesnt work with Sprint. So i ended up getting a Samsung Rant and dont exactly like the web browser so i was wondering exactly how i would go about sharing my data connection with the 8525 via blutetooth. I tried it once and this is what i did:
1. I went to settings and clicked on connection settings under the connections tab.
2. clicked on Add a new modem connection under "My ISP"
3. When i do that it asks to enter a name for the connection and to select a modem, so i select bluetooth as modem and click next.
4. Then it asks for the device the connection is on and i select my rant and hit next
5. then it asks exactly this and has a text box under it: "Enter the number exactly as it should be dialed. include extra numbers, such as an ouside line or credit card" didnt exactly know what to put here so i just put a few randon numbers in to see what next step would be
6. then it asks for user name password and domain....dont know what to put here so i just clicked finish
7. when i try to connect to it. it says connecting and a message on my rant says entering into bluetooth data mode, and the 8525 tries to connect for a minute and says connection failed and goes back to today screen.
So if anybody could tell me in detail what info it is that i need it would be great. and also under select modem drop-down box there is a selection called "cellular line(GPRS, 3G)" is it possible i could just put the info for the data plan in there and it connect to the sprint data plan if that is possible..if it is can you tell me in detail the information u need and how to do it......THANKS

One V CDMA - Problem in enabling data connection

I am using a HTC One V CDMA (Virgin Mobile USA) in India on Reliance CDMA network. The phone was flashed to Reliance and everything is working fine ie I can make/receive calls/sms etc. 1x / EVDO credentials have already been written to the phone.
Now the issue is that I am not able to enable data or the data connection doesn't get enabled automatically. When I try to enable data it says "Disconnected because service is unavailable". But if I press the "Activate this device" button in the settings section, an activation screen 1..2..3 comes up, then wait for 3-4 sec, the 3G symbol gets displayed meaning its able to make a data connection. Now if I go back to the settings page and enable data it successfully connects, and I am able to access internet at EVDO speeds. But after some idle time, the data connection is automatically disconnected and to reconnect I need to repeat the above process. Even if I intentionally disconnect data and try to reconnect, it doesn't happen and I need to go through the "Activate this device" process.
I believe some sort of initialization is missing which is done during the "Activate this device" phase and hence I am able to connect. What could be the reason for this? Is it some setting/configuration that needs to be enabled?
Please pour your valuable tips to resolve this issue.
Thanks
Fixed the issue with auto connection of data, not sure what fixed it exactly, but here are the last changes that I made after which it started working.
You need to use the tool QPST (I used version 2.7.378, an older version didn't work) for this.
In the M.IP tab, disable all profiles except profile 1
Then edit profile 1 and make changes (check attachment)
Then in RmNet tab enable auto connect for device 0 and 1.
After that
PPP Config --> Um --> Enter user/pass as "net" (Req Pw enc should be unchecked)
PPP Config --> AN --> Enter the EVDO credentials given by the MEID registrar (Req Pw enc should be unchecked)
Please note that I got it working merely by trial and error and some of the above changes may not be required and I am not even sure why they are necessary , but with the above configuration I am able to enable data without any problem.
iamvarkey said:
Fixed the issue with auto connection of data, not sure what fixed it exactly, but here are the last changes that I made after which it started working.
You need to use the tool QPST (I used version 2.7.378, an older version didn't work) for this.
In the M.IP tab, disable all profiles except profile 1
Then edit profile 1 and make changes (check attachment)
Then in RmNet tab enable auto connect for device 0 and 1.
After that
PPP Config --> Um --> Enter user/pass as "net" (Req Pw enc should be unchecked)
PPP Config --> AN --> Enter the EVDO credentials given by the MEID registrar (Req Pw enc should be unchecked)
Please note that I got it working merely by trial and error and some of the above changes may not be required and I am not even sure why they are necessary , but with the above configuration I am able to enable data without any problem.
Click to expand...
Click to collapse
Thanks for the above method .. Did you use this method after loading the NVDump file given by the registrar ? ... ALso when i edit the UM and AM feilds and issue write to the phone its showing as the phone has a read only NV ITEMS.
yakaaithiri said:
Thanks for the above method .. Did you use this method after loading the NVDump file given by the registrar ? ... ALso when i edit the UM and AM feilds and issue write to the phone its showing as the phone has a read only NV ITEMS.
Click to expand...
Click to collapse
Well, I had loaded the NVDump earlier, but as I had mentioned it would connect first but if you disconnect or get disconnected it wouldn't reconnect.
Check if the SPC is correct, cause I never got any error like that.
iamvarkey said:
Well, I had loaded the NVDump earlier, but as I had mentioned it would connect first but if you disconnect or get disconnected it wouldn't reconnect.
Check if the SPC is correct, cause I never got any error like that.
Click to expand...
Click to collapse
OP, I am taking a HTC One V for my dad and plan to use it with reliance, could you please tell me what I need to do ?
I already unlocked and rooted the phone. Do I just walk into a reliance store or do something more on computer etc before going there ?
experx said:
OP, I am taking a HTC One V for my dad and plan to use it with reliance, could you please tell me what I need to do ?
I already unlocked and rooted the phone. Do I just walk into a reliance store or do something more on computer etc before going there ?
Click to expand...
Click to collapse
You are talking about Reliance CDMA right?
If yes you need to get the MEID registered, will cost you about Rs 500. Reliance store guys will not do it, have to get it done through some 3rd party provider.
It says Read only NV Items for me too
2kool2btrue said:
It says Read only NV Items for me too
Click to expand...
Click to collapse
That's fine. Its only for one particular NVITEM. Just ignore it.
Hello varkey bhai,
Please Help me with the problem.
1. my meid is registered with reliance.
2. my prl is 00005
3. i am using the handset since 10 months.
4. evdo is also activated on my number.
But i am just getting 1x speeds.
Only thing i feel, i am missing out is on the username,Password,NV file,akey etc.
I have not received the above details from my reigstrar
Can u please guide me how this can be done to start evdo speeds.
Thanks in advance
vakubhai said:
Only thing i feel, i am missing out is on the username,Password,NV file,akey etc.
I have not received the above details from my reigstrar
Click to expand...
Click to collapse
Without the correct EVDO credentials, you won't be able to get EVDO speeds. You need to check with your MEID registrar.
NV dump is not really required and the same can be configured manually if you have the credentials as I have described above. Since you are able to make and receive calls, it looks like the Akey is already set.
so that means if i dont get the credentials from the registrar EVDO can never be started on this handset??
iamvarkey said:
Without the correct EVDO credentials, you won't be able to get EVDO speeds. You need to check with your MEID registrar.
NV dump is not really required and the same can be configured manually if you have the credentials as I have described above. Since you are able to make and receive calls, it looks like the Akey is already set.
Click to expand...
Click to collapse
vakubhai said:
so that means if i dont get the credentials from the registrar EVDO can never be started on this handset??
Click to expand...
Click to collapse
You could check with some other person who does MEID registration, maybe they can retrieve the credentials. But without it, EVDO will not work.
i have an htc droid incredible and i am facing the same problem as mentioned above are the steps above same for my phone also
vikisharma said:
i have an htc droid incredible and i am facing the same problem as mentioned above are the steps above same for my phone also
Click to expand...
Click to collapse
Try it out. It should work.
NVITEM Dump file
iamvarkey said:
That's fine. Its only for one particular NVITEM. Just ignore it.
Click to expand...
Click to collapse
Hello iamvarkey,
i have a sprint htc one that i have flashed but still dont have signal for voice and data. will the nv dump file help resolve this issue and how can i get it.
thanks
jewelman said:
Hello iamvarkey,
i have a sprint htc one that i have flashed but still dont have signal for voice and data. will the nv dump file help resolve this issue and how can i get it.
thanks
Click to expand...
Click to collapse
Simply by loading the Reliance PRL file, you should have voice signal, if not you are doing something wrong.
iamvarkey said:
Simply by loading the Reliance PRL file, you should have voice signal, if not you are doing something wrong.
Click to expand...
Click to collapse
i had done that but didnt work. the phone was sent to me without activating it first with sprint, can this affect it
jewelman said:
i had done that but didnt work. the phone was sent to me without activating it first with sprint, can this affect it
Click to expand...
Click to collapse
I don't think that would be a problem.
Make sure you are using the right PRL file.
No above steps required.
You must have flashed NV Dump already.
Your phone must be activated via *228 already.
Just perform below mentioned steps :
1) Put your phone in Diag Mode by dialing ##3424#
2) Get HTC Diag Mode driver if you don't have it already
3) Download DFS Demo version from DFS Website
4) Connect your phone with DFS, send SPC
5) Now, go to Programming tab -> Data ->
6) Click Read
7) At PPP tab, write "net" (without quotes) to SIP NAI, UID, Pwd field.
Restart the device and here you go, your device would get connected to internet instantly.
keval32 said:
No above steps required.
You must have flashed NV Dump already.
Your phone must be activated via *228 already.
Just perform below mentioned steps :
1) Put your phone in Diag Mode by dialing ##3424#
2) Get HTC Diag Mode driver if you don't have it already
3) Download DFS Demo version from DFS Website
4) Connect your phone with DFS, send SPC
5) Now, go to Programming tab -> Data ->
6) Click Read
7) At PPP tab, write "net" (without quotes) to SIP NAI, UID, Pwd field.
Restart the device and here you go, your device would get connected to internet instantly.
Click to expand...
Click to collapse
Keval,
I recently bought a HTC One E8 and am using Reliance CDMA on Slot-1 and facing this issue.
Would the steps jotted by you help me?
Thanks,
Vinay

Categories

Resources