Related
Hi,
I tryed to upgrade to WM6 but I think I tit someting wrong, I flasht my
old WM5 back but now it is not possible to try flashing to WM6.
stuck in new 3.03.0000 bootloader.
I hope somebody can help me, thanks
Theo
are you stuck in bootloader, or were you successful in flashing WM5 ROM? also, please please PLEASE read the threads in this forum before posting. You are the millionth customer to post this issue
Come on guy, if you can write, i suppose that you can read HERE ...
racerx_ said:
are you stuck in bootloader, or were you successful in flashing WM5 ROM? also, please please PLEASE read the threads in this forum before posting. You are the millionth customer to post this issue
Click to expand...
Click to collapse
I was success full in flashing the WM5 rom back on the device, now I am trying to install hard SPL and WM6 as describe on TRINITYGUIDES.INFO but stuck by the start.
Hard SPL will not flash I see on my Red,Green,Blue screen IPL-SSPL, SPL-1.07.ds , yes I am new with this matter an my English is not too well but please.
please state what the problem is when you try to flash
racerx_ said:
please state what the problem is when you try to flash
Click to expand...
Click to collapse
When I start to flash the sync. is oke but when the bootloader screen appears the flashing stops and the PDA is not connected anymore.
Try to launch again your update while you're in bootloader mode...It should work !!
shym said:
Try to launch again your update while you're in bootloader mode...It should work !!
Click to expand...
Click to collapse
I just did it but when my device is in bootloader mode there is now
connection with my notebook (VISTA) anymore. When I restart my
PDA the connection is established.
there is a wiki guide to flashing under vista..
please note, that when you start the updater, and your device goes in to bootloader, it times out. So connection is lost. Simply start the update again, with device still connected in bootloader
racerx_ said:
there is a wiki guide to flashing under vista..
please note, that when you start the updater, and your device goes in to bootloader, it times out. So connection is lost. Simply start the update again, with device still connected in bootloader
Click to expand...
Click to collapse
Yes I did already as you describe the result is still no connection (error).
hmm... i think you're gonna have to use Pof's splxploit to load hard-spl and then flash another ROM from there.
It's a question of whether SPL 3.03 is exploitable in the same way...
theovdb said:
I was success full in flashing the WM5 rom back on the device, now I am trying to install hard SPL and WM6 as describe on TRINITYGUIDES.INFO but stuck by the start.
Hard SPL will not flash I see on my Red,Green,Blue screen IPL-SSPL, SPL-1.07.ds , yes I am new with this matter an my English is not too well but please.
Click to expand...
Click to collapse
you need to use the active sync after you load wm5 ... that's the trick..
Hello,
I have allways start the update twice, Once where the device starts in this 3-Colors boot screen and a second time to start the Flashing process.
Do not tuch the device Just clos update application on Windows PC and restart it and go through the question process until it starts to flash
Hope it helps for you
Robidog
banzro said:
Hello,
I have allways start the update twice, Once where the device starts in this 3-Colors boot screen and a second time to start the Flashing process.
Do not tuch the device Just clos update application on Windows PC and restart it and go through the question process until it starts to flash
Hope it helps for you
Robidog
Click to expand...
Click to collapse
Thanks guys for all your help but the problem still exists, I keep looking
to this forum and hope in time the problem will be solved.
Thanks a lot
theovdb said:
Thanks guys for all your help but the problem still exists, I keep looking
to this forum and hope in time the problem will be solved.
Thanks a lot
Click to expand...
Click to collapse
Hello,
Explain me the Problem a bit more cloaser (step by step what you are doing)
error messages, and also what image you had bevore on it, I need also to know which which version is written on the 3-colored screen...
Look forward to her from you...
stepw said:
It's a question of whether SPL 3.03 is exploitable in the same way...
Click to expand...
Click to collapse
the answer is yes, splxploit works in new bootloader too.
racerx_ said:
the answer is yes, splxploit works in new bootloader too.
Click to expand...
Click to collapse
the answer is no splxploit not works on SPL 3.03 on my device
So what did you do to fix this ??
shym said:
So what did you do to fix this ??
Click to expand...
Click to collapse
On this moment nothing, I did something wrong by flashing the first time
and now I am stuck in SPL 3.03. I think the best what I can do is waiting for
the official rom from HTC.
Hi All,
I am facing the dreaded 'No GSM' error and unable to flash radio rom problem.
tried to flash every possible rom including original O2 one. All failed on radio ram flash.
Went through various threads and there seems to be no solution yet for universal (though there seems to be a solution for Hermes).
So all, please help me if there is some light in the end of this tunnel
regards
Topgun
i have tried all the possible things but no luck so far.....
please help
I just bought a used XDA with this same problem. Thought if i flash it it would work... any suggestions on what I can do? i havent touched it yet. Thanks
has ANYONE been able to solve this problem?!!!! Pls what did u do step by step.... I spent so much money on this %&%$& Phone!!! pulllleeeessssss
I haven't had this problem, however it sounds like you phone may be SIM locked? If so, you will need to flash it with the native ROM from it;'s origin. If it is SIM and CID locked, it will only take the OEM signed ROM.
Quote from POF (Moderator)
"Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader."
If this is of any help. It is from a thread on CID Unlocking RUU for Uni
Thanks.
i have been through that thread.
well the question on that is 'Is hermflasher okay to flash Universal as well'?
Where is this thread? i can try it.... but cant find the thread on cid unlocking ruu for universal in mermes section....
raskell said:
I haven't had this problem, however it sounds like you phone may be SIM locked? If so, you will need to flash it with the native ROM from it;'s origin. If it is SIM and CID locked, it will only take the OEM signed ROM.
Quote from POF (Moderator)
"Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader."
If this is of any help. It is from a thread on CID Unlocking RUU for Uni
Click to expand...
Click to collapse
Here is the thread
http://forum.xda-developers.com/showthread.php?t=301662&highlight=radio+error
Let me know if you have any luck with this.
cheers
topgunarindam said:
http://forum.xda-developers.com/showthread.php?t=301662&highlight=radio+error
Let me know if you have any luck with this.
cheers
Click to expand...
Click to collapse
no, hermflasher wont work with universal (I dont think) ill consult with some others and report back here our consensus on what to try
I am facing the same 'No GSM' error in xda exec, plz can somebody tell me step by step how to solve it.
Thanks Midget
shall wait for your word.
Midget
topgunarindam said:
shall wait for your word.
Click to expand...
Click to collapse
I'm waiting too.
Good News at Last
atleast it worked for me.
flashed using a different pc with radio 1.18 and it worked.
the radio is working fine with laurentius26's WM6 rom.
atleast my brick comes live again.
LUCKY YOU!!!!!!!!
topgunarindam said:
atleast it worked for me.
flashed using a different pc with radio 1.18 and it worked.
the radio is working fine with laurentius26's WM6 rom.
atleast my brick comes live again.
Click to expand...
Click to collapse
lucky you, I tried that same WM6 ROM (with radio 1.18) and still same problem. I've tried falshing with 2 different desktops and a laptop. Still same problem! Topgun, did u have active sinc installed ? was the PC u used fresh? (no apps installed). do u think if i format my PC it could flash the radio? DID u flash radio only? or the whole laurentious v3 WM6 package (that is at the same time)?
Pls reply
Tbaba said:
lucky you, I tried that same WM6 ROM (with radio 1.18) and still same problem. I've tried falshing with 2 different desktops and a laptop. Still same problem! Topgun, did u have active sinc installed ? was the PC u used fresh? (no apps installed). do u think if i format my PC it could flash the radio? DID u flash radio only? or the whole laurentious v3 WM6 package (that is at the same time)?
Pls reply
Click to expand...
Click to collapse
Him
well it was a laptop dell to be precise.
it was never used for window mobile usage previously and hence fresh Active sync 4.5 was installed.
only radio rom 1st (using the RUU check bypassing)......
once succesful, then laurentiius rom was tried.
one more thing i had entered bootloader manually after disabling AS 4.5
i used the original USB cable as well
hope this helps....
suggest get hold of some friends "win mobile virgin" pc/laptop.
P.S>- i am not sure but this prob might be somewhat related to COM ports available on your machine.
I cannot get past the start up screen! I have the CDMA diamond used
HSPL057 and attempted to update to SWIFTBL WWE DIAMOND ROM V7.5 (FULL) And now it will not go past the boot up screen!! What can I do?
you installed a GSM rom.
you need to do more reading.
1) Reading would have told you the differences between the devices and would have informed you you need hte correct one for your device.
2) you're not the only one who has done this if you do a search you will find how to recover from this issue.
3) i cant stress enough to read first do later. it helps you prevent situations like this.
Thanks for your help
The instructions said it was for SPRINT CDMA devices, that is what I have- I have searched all through out these posts and cannot find out how to recover from this. Can you please help if you know how?
todaytoo said:
The instructions said it was for SPRINT CDMA devices, that is what I have- I have searched all through out these posts and cannot find out how to recover from this. Can you please help if you know how?
Click to expand...
Click to collapse
Wouldn't believe it would say so. Link us to what you're referring to!
All is not lost..
todaytoo said:
I cannot get past the start up screen! I have the CDMA diamond used
HSPL057 and attempted to update to SWIFTBL WWE DIAMOND ROM V7.5 (FULL) And now it will not go past the boot up screen!! What can I do?
Click to expand...
Click to collapse
Hi todaytoo.
Don't worry if you can get the bootloader screen just re flash a CMDA ROM from these Diamond forums.
(enter Bootloader by pushing the reset button while holding volume down key on the side)
Hope this helps ya out.
Try here for a CDMA ROM. http://forum.xda-developers.com/showthread.php?t=430486
I can get into the bootloader screen
Thank you !!! Once I make it to there, do you know where steps are to fix my problem? I have been searching this fourm for hours before I worked up the courage to ask...or throw this phone at the wall
todaytoo said:
Thank you !!! Once I make it to there, do you know where steps are to fix my problem? I have been searching this fourm for hours before I worked up the courage to ask...or throw this phone at the wall
Click to expand...
Click to collapse
Once in bootloader mode connect to your PC via usb lead, wait for drivers to load, then
run a CDMA ROM.
Which CDMA ROM is best to use
I want to make sure that I chose one that will work this time....please suggest one..and Thank you sooo much!!!!!!!!!
todaytoo said:
I want to make sure that I chose one that will work this time....please suggest one..and Thank you sooo much!!!!!!!!!
Click to expand...
Click to collapse
Please read my above post todaytoo, I listed a CDMA there.
I must be retarded
I read your post, but dont see any CDMA ROM on it...
todaytoo said:
I read your post, but dont see any CDMA ROM on it...
Click to expand...
Click to collapse
I guess your kinda stressed at this point, so here is the line from my post
"Try here for a CDMA ROM. http://forum.xda-developers.com/showthread.php?t=430486"
You are correct!! BIG TIME
Thank you so much for your quick help. I am downloading this right now. So once I download, connect via activesync, run the ROM and I should be back in business?
Nearly there..
todaytoo said:
Thank you so much for your quick help. I am downloading this right now. So once I download, connect via activesync, run the ROM and I should be back in business?
Click to expand...
Click to collapse
Fingers crossed yes...
Read all the posts from the CDMA ROM page to get feedback and questions answered etc, and do a little more research via the "Search this forums" button before posting a query.
I guess we all started as XDA newbie's, so don't worry.
Got to log off now todaytoo.
Best of luck, will catch up on forums tomorrow.
gadjet said:
Fingers crossed yes...
Read all the posts from the CDMA ROM page to get feedback and questions answered etc, and do a little more research via the "Search this forums" button before posting a query.
I guess we all started as XDA newbie's, so don't worry.
Click to expand...
Click to collapse
Just 2 questions I think this was a good example.
Where is the CDMA Rom page?
What ROM exactly did you install? (todaytoo)
ok...its not working
ok, im at the bootload screen...I can connect to active sync. I downloaded the CDMA ROM it came in .rar format I changed to it .exe at when i run the ROM it does not do anything....
ok, now its not connecting to activsync....
Is there a trick that im not doing?
renamed a .rar file to an .exe ...new to computing?
You need to unpack/extract the rar file, just like a zip file.
Use winrar, when extracted all the goodies will be revealed!
/Psudo
wow...dont know where my head was
ok, so i have extracted it correctly....my device will still not conntec to active sync...when i plug it in from the bootscreen it changes to USB but activesync cannot find the device....any suggestions
todaytoo said:
ok, so i have extracted it correctly....my device will still not conntec to active sync...when i plug it in from the bootscreen it changes to USB but activesync cannot find the device....any suggestions
Click to expand...
Click to collapse
Dude, search a bit in the forum for things!!
please help me restore my diamond (DIAM100), i flashed it with a CDMA ROM and it hangs at the black "Touch DIAMOND" logo screen. I can enter bootloader, what can i do? Please
If it goes to bootloader, just connect with usb cable and flash with a GSM rom while in bootloader
tonio94 said:
If it goes to bootloader, just connect with usb cable and flash with a GSM rom while in bootloader
Click to expand...
Click to collapse
it works just like that??? or i need a different Diamond custom ruu..? or another flash tool.. i will try this in the evening because now i can't, but i want to be documented when i begin
as tonio94 says, if you can manage to get in to the tri-colored bootloader all you need to do is to flash with a rom that supports your phone... did you remember to hard-spl you phone before all this "mess" or?...
Arju007 said:
as tonio94 says, if you can manage to get in to the tri-colored bootloader all you need to do is to flash with a rom that supports your phone... did you remember to hard-spl you phone before all this "mess" or?...
Click to expand...
Click to collapse
i'm not a total noob in flashing..i just did a mistake...(did not read the post...damn)
i can enter bootloader but i NEVER flashed a rom from bootloader,only from activesync, i don't know if when in bootloader the custom ruu recognizes the phone..or i need another flash tool. im really mad at myself...
i have Hard-SPL
skero666 said:
i'm not a total noob in flashing..i just did a mistake...(did not read the post...damn)
i can enter bootloader but i NEVER flashed a rom from bootloader,only from activesync, i don't know if when in bootloader the custom ruu recognizes the phone..or i need another flash tool. im really mad at myself...
Click to expand...
Click to collapse
No other tools are required. Just put your device into booloader and connect with pc. The bottom of the screen should read USB. At this stage just follow the instructions that you would normal follow when executing the RUU_exe.
I'm sure you have already done this before but here is a guide ....http://modmydiamond.info/index.php?option=com_content&task=view&id=12&Itemid=26&limit=1&limitstart=4
band27 said:
No other tools are required. Just put your device into booloader and connect with pc. The bottom of the screen should read USB. At this stage just follow the instructions that you would normal follow when executing the RUU_exe.
I'm sure you have already done this before but here is a guide ....http://modmydiamond.info/index.php?option=com_content&task=view&id=12&Itemid=26&limit=1&limitstart=4
Click to expand...
Click to collapse
10x allot for your positive feedback, i now how it's done, just i could not believe it is so simple, i thought i bricked my phone, i will try it this evening when i get home.
thank you again
Problem solved, worked to flash like a charm.
thank's
This thread can be closed.
@skero666: i never recalled you as a noob.. i was just trying to give you an easy answer, sorry if i wasn't clear enough.. (^^,) .. and yeah, if you ever manage to get to tri-color bootload then you'll allways be safe... you'll never brick it unless you never manage to get to bootload .. lol
skero666 said:
Problem solved, worked to flash like a charm.
thank's
This thread can be closed.
Click to expand...
Click to collapse
You were lucky - glad you got it sorted
what if it does not even go into bootloader mode? is there a way out of this?
cheers.
I need help changing htc raphael gsm to cdma
I have htc fuze with att provider. im wanna change carrier to boostmobile and keep using my phone. what can i do to change from gsm to cdma. help please.
Hi everyone, I was here last night and asked a stupid question.
Well I tried to flash the phone today, and when i was unlocking it. The Hard-SPL unlocker worked (at least i thought it did)
But when i waited for the phone to reboot, it wont pass the Boot screen. It just says Touch pro2
So, it wont start.... Did i brick it?
Oh, I can access the bootloader by the way. So if there is a way to save this phone, and possibly get to using a custom rom, i would really love to do so...
eternalcold said:
Hi everyone, I was here last night and asked a stupid question.
Well I tried to flash the phone today, and when i was unlocking it. The Hard-SPL unlocker worked (at least i thought it did)
But when i waited for the phone to reboot, it wont pass the Boot screen. It just says Touch pro2
So, it wont start.... Did i brick it?
Click to expand...
Click to collapse
NO, you are fine. Does your bootloader show that you installed the HARD SPL? IF yes, just use the RUU_exe. file and download another rom.
Yes, it shows it is unlocked and running OliNex
I am sorry, i know how to mod other things, psp, xbox, wii, but this is a new thing for me. Thank you for letting me know i havent bricked my phone.
Is there a specific file this RUU_exe that you are talking about? or does that come with every rom?
eternalcold said:
Yes, it shows it is unlocked and running OliNex
I am sorry, i know how to mod other things, psp, xbox, wii, but this is a new thing for me. Thank you for letting me know i havent bricked my phone.
Is there a specific file this RUU_exe that you are talking about? or does that come with every rom?
Click to expand...
Click to collapse
Yes, most chefs include it with there rom. Plug your device into your pc. The bottom should change from serial to USB. Then flash the rom and your done.
Follow ...THESE INSTRUCTIONS and you will be fine.
Thank you so much! I have successfully installed a custom Rom. THANK YOU!!!
eternalcold said:
Thank you so much! I have successfully installed a custom Rom. THANK YOU!!!
Click to expand...
Click to collapse
Glad to have helped...