Related
:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.
Im Not sure exactly what happened here, I've been flashing for nearly a year now a variety of ROMs, and this last time seems to have been fatal.
I went from a custom ROM, did the routine task29 before loading a new ROM; the task29 completed, I returned to bootloader to load the new ROM, and it wouldnt load past 0%. I tried to task29 again, and then that wouldnt load past 0%.
I've since tried mtty and doing set 14 0, task 29, task 8, which restarts it, but now I can no longer manually power it on by pressing hardware keys anymore.. I have to leave it plugged into USB and wait for it to auto-turn itself on after about 5 mins, it loads to "Touch Pro 2" screen, then I can press the little reset button and hold down vol key to get to bootloader. However, it only lasts there about 10 second before turning itself off again, showing the orange light like it's charging. Sometimes I am quick enough to get any ROM or manual HardSPL to try and load at bootloader, but it still sits at 0%.
I have also tried to load a ROM from the SD card, which seems maybe the only option how; however, I have heard you need at least 50% battery, and I have no way to see how much battery I have left, or whether its even charging.
I tried to install from SD yesterday, and got to the gray "Loading" screen, and it just sat there.. I wasnt sure how long it normally takes at that screen, so i powered it off, checked my SD card and now that shows as corrupt and cannot even be formatted... pretty much burnt out as well now, it seems.
Did I do the SD card installation right, using my RHODIMG.nbh file at the root? How long does it normally sit at the Loading screen? I have an 8GB mini-sd I could load from, but I dont want it to burn out as well..
Are there any other options?? I cant even send back to warranty, I dont think, because I cant even load back on the stock ROM or relock it...
Moved to Rhodium General forum because not a cooking problem.
Someone please help... I just tried again to load stock ROM from SD card, as well as custom, it just sits on "Loading..." on the gray screen...
Just for the record, I can get into bootloader, but as of now nothing will load past 0%.
I tried mtty set 14 0, task 29 and task 8, no luck...
I'm certainly not an expert, but just thought I'd throw out a few ideas.
Have you tried charging the phone on the wall charger (not USB) for several hours (like overnight). The fact the phone is powering off by itself suggests that you may be low on battery. USB won't charge the battery sufficiently in some cases of extreme low battery. Try another battery or charge if possible.
Having the RHODIMG.nbh file in the root of your micro-SD card is the correct way to boot from the card. Normally, it doesn't matter if there are other files on the card. But formatting it can't hurt at this point.
Only other thing I can think of, is try to re-flash the radio first, and see it that helps. That's all I can offer up at this point. I was going to suggest trying to flash the stock ROM, but you've already thought of that in your latest post.
Good luck!
redpoint73 said:
I'm certainly not an expert, but just thought I'd throw out a few ideas.
Have you tried charging the phone on the wall charger (not USB) for several hours (like overnight). The fact the phone is powering off by itself suggests that you may be low on battery. USB won't charge the battery sufficiently in some cases of extreme low battery. Try another battery or charge if possible.
Having the RHODIMG.nbh file in the root of your micro-SD card is the correct way to boot from the card. Normally, it doesn't matter if there are other files on the card. But formatting it can't hurt at this point.
Only other thing I can think of, is try to re-flash the radio first, and see it that helps. That's all I can offer up at this point. I was going to suggest trying to flash the stock ROM, but you've already thought of that in your latest post.
Good luck!
Click to expand...
Click to collapse
Thanks for the response; I just tried that (flashing the radio) and it didnt work. Ive also tried flashing a variety of ROMs and nbh files over SD;
It always seems to freeze at the gray "Loading..." screen and get no further.
venomshot629 said:
Thanks for the response; I just tried that (flashing the radio) and it didnt work. Ive also tried flashing a variety of ROMs and nbh files over SD;
It always seems to freeze at the gray "Loading..." screen and get no further.
Click to expand...
Click to collapse
Try using a different USB cable to flash via the PC. If you try the SD route again, some users report that using a NON-SDHC card solves the flashing problem. Give that a shot and then report back. I can't really think of anything else offhand.
cajunflavoredbob said:
Try using a different USB cable to flash via the PC. If you try the SD route again, some users report that using a NON-SDHC card solves the flashing problem. Give that a shot and then report back. I can't really think of anything else offhand.
Click to expand...
Click to collapse
I have tried again using a 512 MB SD card and it still hangs at the "Loading..." screen.
Also, when flashing with any USB cable, I am still stuck at just 0%.. I can get into the bootloader, etc, but it just refuses to flash any image..
So I currently have LightNHB flashed. Since WinMo wont work via USB until I check that one option (forget off hand) I can't establish a USB connection to flash my phone. I tried putting the RAPHIMG.nbh into my SD cards root but that also didn't work, during the boot it said there were no images to flash.
So I removed the Android OS files and reformatted my SD card then places the img file into the root again, and again no image was found.
How would I fix this issue? I cannot seem to flash my phone back to a different WinMo rom.
Got into LightNHB and it has no settings for the USB, it's all in ITA and only one thing I could find in the menus and it gives an error that the file cannot be found. Talk about bare-bones, no wonder I couldn't get this to connect to USB, I don't think it has the ability to.
Ideas?
Pull the battery, SIM(if you have one) and microSD card out.
Press and hold the volume down button while plugging in the USB cord and it should take you to the tri-color screen.
If you haven't already let go of the volume down button, do so now.
You should be ready to flash another ROM!
n-Joie!
R^7Z said:
Pull the battery, SIM(if you have one) and microSD card out.
Press and hold the volume down button while plugging in the USB cord and it should take you to the tri-color screen.
If you haven't already let go of the volume down button, do so now.
You should be ready to flash another ROM!
n-Joie!
Click to expand...
Click to collapse
Didn't know I could be like that but, sadly, error 260; followed to the letter :/
I can't get it to recognize .nbh. When I was able to get into the WinMo of LightNBH it seems it's WM5? CDMA? On my GSM phone... I know my version is dual CDMA and GSM. Though I use the latter.
It has HardSPL because Tri-colour screen says 1.90.OliNex
Can you get it to recognize USB in said bootloader mode? You should be able to flash from your PC using bootloader mode...
arrrghhh said:
Can you get it to recognize USB in said bootloader mode? You should be able to flash from your PC using bootloader mode...
Click to expand...
Click to collapse
No, from what I can gather LightNBH doesn't have the stock USB connection info included in WinMo. Settings > Connections was empty. In fact all of it is empty (settings), I couldn't get to my SD card to run cab files to give me control over my phone.
Is there anyone else running the LightNBH flash that can confirm this? I can't even establish a USB line within Android.
Ventrik101 said:
No, from what I can gather LightNBH doesn't have the stock USB connection info included in WinMo. Settings > Connections was empty. In fact all of it is empty (settings), I couldn't get to my SD card to run cab files to give me control over my phone.
Is there anyone else running the LightNBH flash that can confirm this? I can't even establish a USB line within Android.
Click to expand...
Click to collapse
Hrm, I figured bootloader mode would be separate from WinMo entirely... so not having usb drivers in WinMo should effect it.
So you're saying when you're in bootloader mode, and you plug in USB it still just says "serial"?
arrrghhh said:
Hrm, I figured bootloader mode would be separate from WinMo entirely... so not having usb drivers in WinMo should effect it.
So you're saying when you're in bootloader mode, and you plug in USB it still just says "serial"?
Click to expand...
Click to collapse
It doesn't even say serial.
Code:
RAPH100
SPL-1.90.OliNex
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
That's all my boot-loader says and I didn't think drivers had any effect here but as it sits I get an error 260 unable to connect from the ROM updater's that came with Monfro, TAEL, and Energy, as well as Task_29.
Erm... It should definitely say "Serial" near the bottom. Give it 10 secs or so...
When you plug into USB, that should convert to say USB...
Did you remember to rename the .nbh file into "RAPHIMG.nbh"? You could also use a sd card adapter or another device that has working usb storage that takes micro sd cards and then drag the .nbh file on the sd card via another device.
See what happens when we get in a hurry? At least that's how i ended up with Litenbh on my TP stuck in a boot loop.
I tried the PWR + VOL DN while soft resetting. No luck. Then i was going to try holding those 2 buttons while plugging it in to USB, I was holding the buttons as i unplugged it. It jumped to the serial screen as soon as i unplugged it.
I'm sure you have gotten this fixed or a new phone by now, but in case ur as broke as me, and still playin with a TP cause you HAVE to.
Maybe this will help. Hold power + volume down while plugging/unplugging it from the PC. Might get lucky like i did.
I know it says Development discontinued, but the TP is old enough that the info i'm looking for is getting buried. Most d/l links i find are dead now, so i'm getting jumpy on the clicker finger.
But I for one think this link and the file itself needs to be taken down. I know it's only 2 of us so far, but dangit what a pain!!!
http://forum.xda-developers.com/showthread.php?t=601751
EDIT: Wow i didnt realize this thread was that old also.
Alltel Touch Pro (yeah it's old, and the keyboard doesn't work)
Using Updated Alltel ROM from HTC site.
Hmmm...
FroYo thread
Gingerbread thread
And yes, this are continuing projects...
Please read the first few posts before attempting anything. It's really does not hurt to try but your experience may vary slightly if you don't know what you are doing.
On that note, I am PMing the thread OP/forum mod to see if there is a way to link to the continuing project threads.
Actually the first post in that thread that you make mention of, has a link to the continuing project.. heh
Pretty sure I bricked my phone. Been digging through the forums all night and can't find anything.
When I plug it into USB I can get the White LED indicator. Only sign of life tho.
Can't boot the phone at all though. Always just a black screen; no backlight.
No motorola logo..
RSDLite won't recognize because I can't get into bootloader mode.
Battery is fine, checked it with a multimeter and I'm at 3.3V
Tried a friend's Defy battery.. no dice.
Any suggestions?
does your friend battery have a full charge on it?
it happens to me before, i turn the defy off, plug the charger, and left it for 30 to 45 minutes and i can boot afterwards. try it, might work for you too.
thanks been trying that out. his has full charge. I also mcgyvered mine and it's fully charged as well.. hmmm
what did you do that caused the bricked phone? did you try to downgrade it from 2.2 to 2.1? because that caused me the same thing, white led, rsd wont recognize it (windows error sound when plugged into usb), and i couldnt solve it, had to bring it back to motorola...
sent from my cm7 defy...
i have read somewhere in the devs forum about a corrupt bootloader experienced by one of our friend there. try to look into that and possibly get you some clues. Another possibility is to remove your sdcard, my crappy class 6 gives me a white lights only boot when im still in froyo, although it happens only once or twice. at this point, might as well try it out eh?
you need to flash with rsd it will read the phone is stuck in bootloader mode download your stock sbf and flash with rsd it will bring your phone back to life!!
make sure you remove battery plug in usb cable then replace battery while holding the vol + key
zakoo2 said:
what did you do that caused the bricked phone? did you try to downgrade it from 2.2 to 2.1? because that caused me the same thing, white led, rsd wont recognize it (windows error sound when plugged into usb), and i couldnt solve it, had to bring it back to motorola...
Click to expand...
Click to collapse
I actually purchased it from someone who said that it was bricked. I am trying to get back in touch with them to find out what happened but no info yet. I've been trying to deduce what could of happened. But one thing I'm almost certain of is it wasn't water damaged. As I said the battery is still intact and I've never seen a phone go without taking the battery with it. Moisture indicators look fine as well.
I don't get any sounds when plugging the phone into USB. Device manager doesn't even blink. Can you return to Motorola if you are off contract? Any info on how that works? Not giving up yet, just wondering.
cengiran said:
i have read somewhere in the devs forum about a corrupt bootloader experienced by one of our friend there. try to look into that and possibly get you some clues. Another possibility is to remove your sdcard, my crappy class 6 gives me a white lights only boot when im still in froyo, although it happens only once or twice. at this point, might as well try it out eh?
Click to expand...
Click to collapse
Thanks, I will definitely look into that corrupt bootloader situation. I pulled the sd card (been in there the whole time) but it didn't make a difference. There wasn't really much on the SD Card except for a few empty (autopopulated) directories: LOST.DIR, .android_secure, etc.. and the stock froyo SBF file for the phone: p3_jordan_umts_2.2.1..(blahblah).sbf it's a US T-Mobile Defy.
So it likes like maybe the previous owner was trying to flash. Although I don't know why they would put SBF on the SD.
pmp326 said:
you need to flash with rsd it will read the phone is stuck in bootloader mode download your stock sbf and flash with rsd it will bring your phone back to life!!
Click to expand...
Click to collapse
pmp326 said:
make sure you remove battery plug in usb cable then replace battery while holding the vol + key
Click to expand...
Click to collapse
RSD doesn't ever see the phone at all. Thanks for the suggestion. Tried to insert battery after plugged in and while holding vol + key but no difference. Been trying all sorts of key combinations from the forums but no luck there either. The drivers are completely up to date.
All suggestions appreciated! Thanks guys!
any more ideas by chance ?
It's a silly thing, but have you tried pressing the power button AFTER connected USB? Anyway try switching Config-->DeviceID options in RDS.
I was stuck at your point, only white led, hacked the battery and it has been recognised by RDS after some unistall/reinstall... try, try and try again
This happend to me too (black screen, only white led) when i tried to flash some korean froyo. I just removed the battery, connected usb, put battery back, power + vol [+] and RSD recognised it (even if screen was black)
I confirm (I had the same problem...) that your Defy is not bricked :
- don't connect the phone to the PC
- launch RSDLite and choose your SBF
- remove the battery cover (of your phone of course, not your PC ! )
- remove the battery
- plug the USB cable only in the phone
- your phone in left hand, press power + vol.up with 2 fingers of the same left hand
- put the battery into the phone with your free hand, so the right !
- when the white led appears, you can remove your 2 fingers from buttons
- then plug the USB cable in the PC
- RSDLite recognize your Defy !!!
- you can flash...
Sorry for my bad english !
If all above suggestions still fail on you. I would think it might possibly the USB port is broken or some hardware issue which is why it was sold to you as bricked Defy in the first place.
one2wan said:
I confirm (I had the same problem...) that your Defy is not bricked :
- don't connect the phone to the PC
- launch RSDLite and choose your SBF
- remove the battery cover (of your phone of course, not your PC ! )
- remove the battery
- plug the USB cable only in the phone
- your phone in left hand, press power + vol.up with 2 fingers of the same left hand
- put the battery into the phone with your free hand, so the right !
- when the white led appears, you can remove your 2 fingers from buttons
- then plug the USB cable in the PC
- RSDLite recognize your Defy !!!
- you can flash...
Sorry for my bad english !
Click to expand...
Click to collapse
Thank you, my phone is alive
This thread is mostly for the E980 but will help all others as much as possible.
Please be sure to follow all steps!!! If you would like help, please be courteous to all on this thread. Thanks
_________________________________________
Long story short...I hard bricked my phone by flashing a rom for the wrong phone. Phone would not boot at all. No signs of life. When plugged into the computer...I noticed a driver being installed (Qualcomm HS-USB QDLoader 9008). A quick search...and a few forums later...I knew for sure my phone was bricked.
Here's what you will need:
MicroSD card
MicroSD card reader
Linux (I used Ubuntu) and Windows
Patience
_________________________________________
Here is what I did...In Windows
1 - Download your stock firmware for your phone. I have an e980...so my file would be one that ends in .tot...most other Optimus G Pro phones have stock files that end with .kdz (search XDA)
2 - Download http://d-h.st/naQWindowsLGFirmwareExtract-1.2.1.0-Release.zip - 1.33 MB. This will work on both .kdz and .tot files.
3 - Open WindowsLGFirmware and locate your stock firmware. A list of files will show up. Click on the boxes on the left of the name of the file for the following...SBL1.bin, SBL2.bin, SBL3.bin, aboot.bin, rpm.bin, tz.bin, backupGPT.bin, recovery.bin, persist.bin, modem.bin, misc.bin, boot.bin and PrimaryGPT.bin.
4 - Then click on "Extract.tot" (or Extract.kdz). Extracted files will be in the same folder at the WindowsLGFirmare.
5 - The PrimaryGPT.bin file now has to be written to the MicroSD card. I used http://sourceforge.net/projects/win32diskimager/files/latest/downloadWin32DiskImager.
The rest of the files, put on a usb stick for now.
Once that is done...boot into your Linux Distro(I installed Ubuntu due to permissions needed in the following steps)
6 - Once booted into Linux, have your sd card in the card reader and plugged into your computer...go to Terminal and type ls /dev/sd*
(You should see something like this.../dev/sda /dev/sda1 /dev/sda2 /dev/sda5
/dev/sdb1 /dev/sdb2 /dev/sdb3 /dev/sdb4
/dev/sdb5 .......... /dev/sdb36
7 - Next...in terminal type sudo gdisk -l /dev/sdb
You will see a list with columns for Number, Start, End, Size, Code and Name.
You must match the number on the list with the files you downloaded earlier in Windows. Write down the number in the number column for each of those files. (Example: SBL1 for me was number 2)
Now transfer the files on the usb stick that you downloaded earlier in windows to your linux desktop.
8 - Now in Terminal type sudo -i
Then type dd if=/the location of the file/name of file.bin of=dev/sbd(now type the number that your file was on the list)
This is what mine looked like dd if=/home/ricanares/Desktop/aboot.bin of=/dev/sdb5
You must do this for every file downloaded from our stock firmware(except for PrimaryGPT.bin)
9 - Now reboot back into Windows. Insert the sd card into your phone. Plug the phone into the USB port. For me, the soft keys lit up, which made me feel closer to recovering my phone. At this step, not much happened for me for at least 10 minutes. Then while plugged into the usb port and while sd card was still in phone...my battery fell out (didn't have the battery door on). Put the battery right back in...and the LG boot screen came on.
10 - Finally...remove battery while the sd card is still inserted. While holding down the volume keys, plug the phone back into the usb cable and now you should be in download mode. Now follow the guide found at http://forum.xda-developers.com/showthread.php?t=2302660 and your phone should be back to stock in minutes.
_________________________________________
If phone does not go into Download Mode...try volume up and power or volume down and power. Another thing to try if this doesn't work for you...in step 8...instead of using your stock firmware recovery.img...search xda for a cwm or twrp image to flash. Just rename it to recovery.img.
Good luck to all. Hopefully I wrote this guide clear enough. This is my first ever!!! I finally got my hard bricked phone working and had to share the news. After trying to fix this for the past 2 days...I am off to bed. If you wish to buy me a beer...PM me. Thanks
-----------------------------------------------------------------------------------------
This guide was made for the LG Optimus G Pro E980 but may work for all other variations.
For me, when it only lights up for a split second when I remove the battery. My battery is at 100% (tested on my other device) and I can't do anything with the device. I've waited a bit and nothing has happened. I have not seen the backlights turn on except for when I remove the battery.
edit: could you link the stock firmware that you used?
edit2: when i use my empty battery, it lights up, but it disconnects/turns off every ~3 seconds. It may be because this battery is defective, but did this happen to you?
dylanraga said:
For me, when it only lights up for a split second when I remove the battery. My battery is at 100% (tested on my other device) and I can't do anything with the device. I've waited a bit and nothing has happened. I have not seen the backlights turn on except for when I remove the battery.
edit: could you link the stock firmware that you used?
edit2: when i use my empty battery, it lights up, but it disconnects/turns off every ~3 seconds. It may be because this battery is defective, but did this happen to you?
Click to expand...
Click to collapse
I rebricked my phone to see exactly what I should tell you...here's what I did...When the soft key lights came on...i left the phone plugged into my computer for 10 minutes. Then disconnected the phone...held down both volume keys and plugged in the usb cord...it then booted to download mode where I was able to continue to the link on step 10.(Try this a few times)
The stock firmware i used..i found here...http://forum.xda-developers.com/showthread.php?t=2420219 Right under where it says "I am aware about my links..." there is a link...click it and download these 2 files LGE980AT-00-V20g-ATT-US-APR-28-2014.zip.htm and LGE980_20130314_LGFLASHv151.dll
I had originally also thought my battery was defective...but it was fine. As long as the battery has a decent amount of charge...you should be set. Keep me updated. Good luck
Few questions..
When you use the imager to write PrimaryGBT.bin to the MicroSD card, does it then seem "corrupt" to Windows and asks to reformat it?
Also, simply after sticking the MicroSD card into your phone and plugging it in (w/ battery) the soft keys just light up? And did they stay lit up even when not connected to the computer? This didn't happen for me with my full battery.
And one you didn't answer: with my empty battery it the soft keys light up, but they turn off and disconnect from my computer every ~3 seconds; did this happen to you?
dylanraga said:
Few questions..
When you use the imager to write PrimaryGBT.bin to the MicroSD card, does it then seem "corrupt" to Windows and asks to reformat it?
Also, simply after sticking the MicroSD card into your phone and plugging it in (w/ battery) the soft keys just light up? And did they stay lit up even when not connected to the computer? This didn't happen for me with my full battery.
And one you didn't answer: with my empty battery it the soft keys light up, but they turn off and disconnect from my computer every ~3 seconds; did this happen to you?
Click to expand...
Click to collapse
ricanares said:
I rebricked my phone to see exactly what I should tell you...here's what I did...When the soft key lights came on...i left the phone plugged into my computer for 10 minutes. Then disconnected the phone...held down both volume keys and plugged in the usb cord...it then booted to download mode where I was able to continue to the link on step 10.(Try this a few times)
The stock firmware i used..i found here...http://forum.xda-developers.com/showthread.php?t=2420219 Right under where it says "I am aware about my links..." there is a link...click it and download these 2 files LGE980AT-00-V20g-ATT-US-APR-28-2014.zip.htm and LGE980_20130314_LGFLASHv151.dll
I had originally also thought my battery was defective...but it was fine. As long as the battery has a decent amount of charge...you should be set. Keep me updated. Good luck
Click to expand...
Click to collapse
Thank you for your tutorial... I managed to get the 'unbrick microSD', but my phone keeps being undetected by my pc. The two soft key lights simply flashed on and then came off again in 1 second or less... Does your phone keep the lights on when connected in that manner?
To be sure if I followed your steps correctly:
1 - Battery: inserted; microSD: inserted; phone plugged-in -> soft key lights ON
2 - Wait 10 minutes
3 - Remove battery and put it back in again without disconnecting the phone;
4 - LG bootscreen should appear;
5 - Disconnect the phone and connect it again pressing the volume keys.
6 - Download mode should be back
Is that right?
dylanraga said:
Few questions..
When you use the imager to write PrimaryGBT.bin to the MicroSD card, does it then seem "corrupt" to Windows and asks to reformat it?
Also, simply after sticking the MicroSD card into your phone and plugging it in (w/ battery) the soft keys just light up? And did they stay lit up even when not connected to the computer? This didn't happen for me with my full battery.
And one you didn't answer: with my empty battery it the soft keys light up, but they turn off and disconnect from my computer every ~3 seconds; did this happen to you?
Click to expand...
Click to collapse
The image writer did show that the MicroSD card needed to be reformatted...so it does seem corrupted only because of the flashed .bin file. But does not need to be reformatted till the phone is fully back up and running.
The soft keys did light up for me only after I flashed it with all files onto the MicroSD card in the steps I listed above. Did not stay lit up for more than a few seconds. When disconnected from the computer...they would not light up.
I don't know about an empty battery...but with my battery which was at at least 60%...the keys did light up for a few seconds ...and i did keep getting disconnected from the computer which is why i waited 10 minutes before doing anything.
Have you tried other key combinations? Try volume down, home key and power button. Try with and without being plugged into the usb port.
Il Palazzo said:
Thank you for your tutorial... I managed to get the 'unbrick microSD', but my phone keeps being undetected by my pc. The two soft key lights simply flashed on and then came off again in 1 second or less... Does your phone keep the lights on when connected in that manner?
To be sure if I followed your steps correctly:
1 - Battery: inserted; microSD: inserted; phone plugged-in -> soft key lights ON
2 - Wait 10 minutes
3 - Remove battery and put it back in again without disconnecting the phone;
4 - LG bootscreen should appear;
5 - Disconnect the phone and connect it again pressing the volume keys.
6 - Download mode should be back
Is that right?
Click to expand...
Click to collapse
The soft keys did not stay on for more than a few seconds for me. The steps are correct. Try removing the sd card and try holding the volume buttons and connect to the computer via usb. If that doesnt work...try different key combinations...volume down, home button and power...try while plugged into the computer and without. Let me know if you need further help.
ricanares said:
The image writer did show that the MicroSD card needed to be reformatted...so it does seem corrupted only because of the flashed .bin file. But does not need to be reformatted till the phone is fully back up and running.
The soft keys did light up for me only after I flashed it with all files onto the MicroSD card in the steps I listed above. Did not stay lit up for more than a few seconds. When disconnected from the computer...they would not light up.
I don't know about an empty battery...but with my battery which was at at least 60%...the keys did light up for a few seconds ...and i did keep getting disconnected from the computer which is why i waited 10 minutes before doing anything.
Have you tried other key combinations? Try volume down, home key and power button. Try with and without being plugged into the usb port.
Click to expand...
Click to collapse
Try this...
Try removing the sd card and try to get into download mode (hold volume buttons and plug into computer via usb)
No lights would come on for me while I wasn't plugged into the computer. I'm not going to give up. Lets get this working
ricanares said:
Try this...
Try removing the sd card and try to get into download mode (hold volume buttons and plug into computer via usb)
No lights would come on for me while I wasn't plugged into the computer. I'm not going to give up. Lets get this working
Click to expand...
Click to collapse
I can't get the LG bootscreen... could you provide us a short video? thank you
I'm trying with a microSD created using the e980 v20g .tot file... I managed to download an e986 kdz file (many mirrors are down). Maybe it needs the right partitions to boot from sd, even if the two models should be very similar (except for the modem).
Il Palazzo said:
Thank you for your tutorial... I managed to get the 'unbrick microSD', but my phone keeps being undetected by my pc. The two soft key lights simply flashed on and then came off again in 1 second or less... Does your phone keep the lights on when connected in that manner?
To be sure if I followed your steps correctly:
1 - Battery: inserted; microSD: inserted; phone plugged-in -> soft key lights ON
2 - Wait 10 minutes
3 - Remove battery and put it back in again without disconnecting the phone;
4 - LG bootscreen should appear;
5 - Disconnect the phone and connect it again pressing the volume keys.
6 - Download mode should be back
Is that right?
Click to expand...
Click to collapse
when phone is plugged in...do you see the lg drivers installed for your phone or do you still see the Qualcomm driver?
ricanares said:
when phone is plugged in...do you see the lg drivers installed for your phone or do you still see the Qualcomm driver?
Click to expand...
Click to collapse
The phone is detected in QHSUSB_DLOAD mode (all the drivers have been already installed) only if the microSD is removed, the battery is inserted and I press the volume keys while connecting it to the pc. Otherwise, it remains undetected.
The soft key lights go on only connecting it with the microSD inserted and without the battery.
My battery was at a decent charge (40-60%) 3-4 days ago... I don't know if it went out of charge now.
Il Palazzo said:
The phone is detected in QHSUSB_DLOAD mode (all the drivers have been already installed) only if the microSD is removed, the battery is inserted and I press the volume keys while connecting it to the pc. Otherwise, it remains undetected.
The soft key lights go on only connecting it with the microSD inserted and without the battery.
My battery was at a decent charge (40-60%) 3-4 days ago... I don't know if it went out of charge now.
Click to expand...
Click to collapse
Try plugging the phone into an outlet with battery and sd card inserted and see if any lights come on...then try to power on while sd card is inserted. Also, try and reboot computer. I will be on here for a few more hours.
ricanares said:
Try plugging the phone into an outlet with battery and sd card inserted and see if any lights come on...then try to power on while sd card is inserted. Also, try and reboot computer. I will be on here for a few more hours.
Click to expand...
Click to collapse
another thing you can try...try holding the home button down and press power
ricanares said:
another thing you can try...try holding the home button down and press power
Click to expand...
Click to collapse
No lights on using the ac adapter. I've also discovered that the e986 kdz file cannot be read by the firmware extractor.
Thank you for your help... I'll continue tomorrow (it's quite late and I've got to get to work early :S) with your help. I'm planning to leave the phone to LG assistance if I can't recover it before this weekend.
Please let me know if you can make a short video
Il Palazzo said:
I can't get the LG bootscreen... could you provide us a short video? thank you
I'm trying with a microSD created using the e980 v20g .tot file... I managed to download an e986 kdz file (many mirrors are down). Maybe it needs the right partitions to boot from sd, even if the two models should be very similar (except for the modem).
Click to expand...
Click to collapse
The files you used to flash the sd card were from the .tot or the .kdz file? Do you have an e980?
Il Palazzo said:
No lights on using the ac adapter. I've also discovered that the e986 kdz file cannot be read by the firmware extractor.
Thank you for your help... I'll continue tomorrow (it's quite late and I've got to get to work early :S) with your help. I'm planning to leave the phone to LG assistance if I can't recover it before this weekend.
Please let me know if you can make a short video
Click to expand...
Click to collapse
I will try and get a video done asap. Please hit me up tomorrow so that I can help you.
ricanares said:
The files you used to flash the sd card were from the .tot or the .kdz file? Do you have an e980?
Click to expand...
Click to collapse
ricanares said:
I will try and get a video done asap. Please hit me up tomorrow so that I can help you.
Click to expand...
Click to collapse
I own an e986 (as I mentioned in my thread)... but I think that the two models are similar. I didn't think about the possibility to boot up the phone using the microSD, but as I saw on the net it's quite common for all qualcomm-based devices, so I'll give my phone another chance before leaving it to LG assistance.
Il Palazzo said:
I own an e986 (as I mentioned in my thread)... but I think that the two models are similar. I didn't think about the possibility to boot up the phone using the microSD, but as I saw on the net it's quite common for all qualcomm-based devices, so I'll give my phone another chance before leaving it to LG assistance.
Click to expand...
Click to collapse
OK. I will research to see if there are any differences and let you know tomorrow if I found anything.
ricanares said:
OK. I will research to see if there are any differences and let you know tomorrow if I found anything.
Click to expand...
Click to collapse
Any news? Thank you
Il Palazzo said:
Any news? Thank you
Click to expand...
Click to collapse
Some news. After reading for hours yesterday...even though the e980 and e986 are similar...they do have some differences when it comes to the software. You must download the kdz for your phone and use a kdz extractor. I believe you said the extractor in this guide is not working for you...if you search google, you will find a few. Once you're able to extract the original firmware...restart the process. Reformat the sd card before beginning. I am in class right now, but will do my best to respond to you quickly.