Hi,
New Dash owner here, I tried searching for an answer, but did not have any success.
When I try to connect to a wireless access point at work with a static IP address it just shows connecting and never actually does. I can connect to other access points that use DHCP with no problem. I entered the IP address, subnet, default gateway, DNS servers and WEP encryption key that I use on my laptop. Am I missing something? I am using 3VOLUTION WM6.5.
Thanks
Related
Does anyone know how I can find out the mac address of my xda IIs ? I have a dreytek wireless router at home which uses a mac based access control list. I've tried the addresses that appear in wireless LAN manager ( BSSID and MAC ) but no joy. The only way I can connect is to switch off the access list feature completely
jeff
Hi Jeff,
Switch off the Access control, and let the XDA IIs join the wireless network. Then go into Diagnostic Tools --> View DHCP assigned addresses, and you will get a list of MAC addresses, IP addresses and hosts on the network. Match your phone's name to the MAC address.
Then you can turn access control on again and input the phone's mac address into the "allowed" list.
Thanks for the reply. I've kind of done that as you can see from the DHCP table below
DHCP server: Running
Index IP Address MAC Address Leased Time HOST ID
1 192.168.1.1 00-50-7F-23-97-CC ROUTER IP
2 192.168.1.10 00-00-00-00-00-00 BAD IP
3 192.168.1.11 00-0D-61-4E-A7-F7 0:00:04.600 hubbo
4 192.168.1.12 00-09-2D-0E-49-61 9:24:34.170
(not sure about that BADIP line ! )
I would say my MAC is 00-09-2D-0E-49-61 but it's still not working.... odd.
Is there no way that you can tell the MAC address from the phone without connecting to a network.
Here is a freeware that will allow you to find your MAC with no connection. I used it on my PDA2K.
http://www.freewareppc.com/communication/vxipconfig.shtml
Install on your device. Just turn the wifi on and run the program and it will give you the MAC and additional device info. Don't have the PPC connected to the USB or it will identify that device.
Sorted thanks, whilst in PC World I scanned for a Wireless network, and found three, hehe! Once connected used that utility to get my MAC.
Many thanks!
wifi and drayteck router
hi i see u have a draytech router how did u manage to get streaming video? i have been trying now for hours.I can get the video on my laptop without any problems but my m2000?????
i think the problem lies within the vpn settings as when i try to open http://house:8080 i get the message vpn connection required.
any help would be greatly recived (i have the vigor 2600g)
thanks in advance
delboy
im trying to get an internet connection through my wifi connection. i have done search's and lots of people seem to be asking the same question but nobody has the answer.
at the moment i can access my c: using an application called Resco explorer. but i can not connect to the internet. im not sure what setting i should have on the wifi manger and on my pc. im also using AOL as my isp.
PLS PLS help :lol:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
looks like a no then
I got mine working but setting my wireless network adapter to connect to "Work".
Under Settings>Connections>Tasks>Manage existing connections>Proxy Settings> check the "This network connects to the internet" box
then
Under Settings>Connections>Advanced>Select Networks> "Programs that automatically connect to the internet should connect using:" to "My Work Network" (and the same with one for private network)
Also in your active sync settings, make sure your connection settings allow network (Ethernet) and RAS connections.
From previous research around this, i'm pretty sure you can only use the internet pass through under "WORK" settings only.
*thought i'd better register and contribute as i've gained a fair bit from this forum.
no good anyother ideas. i have searched through hundreds of threads and still no go
help pls
Make sure you have "Enable Netbios over TCP/IP" checked in your TCP/IP Advanced settings.
i have done this on both my wifi network and my isp network.
still not working
Have you checked if you're getting an IP address from your Wireless Router's DHCP server? Also DNS settings and Gateway address should be there.
You can check this easily by using vxUtil (free )
these are my settings:
tiacxwln1 - tiacxwln compatible wireless
Ip address 192.168.0.2
subnet mask 255.255.255.0
default gateway 192.168.0.1
primary DNS 192.168.0.1
secondary dns
primary wins
seconfdary wins
DHCPs server 192.168.0.1
under serial usb
IP address 192.168.55.101
subnet mask 255.255.255.0
default gateway 192.168.55.100
primary DNS 127.0.0.1
Getting this error when I tried to allow my broadband connection to share with my wifi connection. If I unplug the wifi connection and try and share with another network I don’t get any errors.
Internet connection sharing (ics) cannot be enabled due to IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1 please ensure that no other client on the network is configured to use 192.168.0.1
hmmm ... ever had the same problem. all devices are able to connect to the same router except mine sx66.
then i change the router's channel to '1' .. tada .. now everyone is connected. it might sounds silly, but it worked for me.
try changing your ap wireless channel.
Re: does NE1 have the answer to wifi not connecting to the n
robboy said:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
Click to expand...
Click to collapse
i found the problem with activesync 3.8 and 4.0 somehow, so i reverted back to 3.7, now wifi can sync.
afaik, connecting to internet has nothing to do with activesync. its a direct connection to wifi router. use work location and check the proxy settings if u hv any? (at home i use connect to internet without proxy, at work i use connect to internet with proxy).
Also, for Activsync with wifi, make sure that the WINS server address is that of yr PC u want to sync with.
For some odd reason I am unable to use WIFI at work on our 3COM wireless routers. I can connect to all the access points fine, but it never routes. I can ping other internal IP addresses, but I am not able to ping public IP addresses outside of our network.
I started looking through logcat and found that it is setting the gateway to 120.123.1.0 when it should obviously be 192.168.1.1. I looked everywhere in the router settings and the gateway is specified as 192.168.1.1. This is obviously a problem! Why in the world is it picking up this bogus gateway IP address from these routers?
I've had no problems with any other routers and an office neighbor is able to get wifi just fine on his iPhone. Any clues?
Well it is definitely just a gateway issue. I opened a shell with adb and set the gateway to 192.168.1.1 manually and I was able to to access the internet via wifi on the 3COM wireless router.
Does anyone have any idea why the EVO would not obtain the correct gateway? Every other system on the wireless network gets the right data from the DHCP server. I don't care how much of a long shot your suggestions or ideas are, I am looking for any leads to investigate. I've already double checked everything in the wireless router and DHCP server and the mysterious gateway IP (120.123.1.0) is nowhere to be found.
IP, netmask, DNS, DHCP server, and lease time are all coming in fine.
Since installing Froyo on my Desire, I can not connect to my local wireless router (Belkin N1 Wireless router) when using a dynamic IP address. Previously (on eclair) this was no problem what so ever.
When I try connecting, it keeps saying it's trying to aqcuire an IP address, but nothing happens.
When I check the routers overview of connected devices (DHCP client list), I see this:
ip address: 192.168.2.4
host name: android_f07d6a45ÿÿÿÿþÿÿÿ (yup, strange characters)
I tried connecting to my macbook via WIFI, and that worked without a hitch.
After restoring factory settings on my Desire, factory settings on the router, installing newest router firmware... I tried again, but to no avail!
Then I gave the Desire a static IP address and presto; I could connect to my wireless router without a problem.
In conclusion:
Before Froyo: connecting to wireless router with dynamic IP addresses = no problem
With Froyo: can only connect to router with static IP and Desire's hostname contains strange characters
Most other wifi networks seems to work.
Anyone else having similair problems? Is the Desire's strange hostname the problem?
This was a problem for me with Eclair too, and yes I'm still experience it, the only solution I found before was "wifi-fixer" or what ever the app was called (it's found via the market). But it did not work all the time... :-(
Update: I can connect to Dynamic-IPs without noticing any strange Chars. But its the "unable to..." that's similar to your's.
static IP won't help
I'm a little frustrated becouse even static IP is not helping
can you tell me how your exact PHONE config's are?
like gateway dns and so on,..
THX,
s.
s.zamani said:
I'm a little frustrated becouse even static IP is not helping
can you tell me how your exact PHONE config's are?
like gateway dns and so on,..
THX,
s.
Click to expand...
Click to collapse
These settings should be different from router to router
I can give you mine, but I doubt it will help you:
IP: 192.168.2.4
Gateway: 192.168.2.1
Subnetmask: 255.255.255.0
DNS 1: 192.168.2.1
DNS 2: BLANK
Depening on your router and settings, you might have to change the ".2." in all of these to ".0."
The "4" in the IP address is also free for you to chose (must be available though)
This is how i fixed the problem. after 2 days of RND
Activated hotspot on my arc, and waited for my laptop to connect. After you get connected your laptop adapter will show limited connectivity/no internet.
Now go to the market and download "Network info"
open network info and find out the IP address of your device.
it will be something like 192.168.43.1
now go to to your wireless setting of your laptop, and change the settings to DHCP to static.
if your phone has IP 192.168.43.1
Then configure your laptop's ip 192.168.43.2 subnet 255.255.255.0 gateway will be your phones IP. ie 192.168.43.1.
dns 8.8.8.8
8.8.4.4
DONE