How to get HP iPAQ 6365 into bootloader mode? - Upgrading, Modifying and Unlocking

Hey all, does anyone know how to get into the bootloader mode of hp ipaq 6365? I tried updating ROM 1.11 version into it, but i always get an error 608: ruuclientdriver.dll could not initialize the device. I just haven't been able to update the ROM image.
Now, i am trying to update through the bootloader program but i simply dont know how to get my phone in bootloader mode. Also, it would be great if anyone could teach how to update ROM from SD card?
Right now, i havent been able to use my phone. My phone only goes up till the align tap screen after which i cant do anything with my phone. Please help !!!!!!

Related

*************O2 MINI DEAD***********

Hello
I tried upgrading ROM for O2 mini inthis process iam left with only a blank screen with ** USB , Ver 1.00
Please help me out with this problem
I even dont have the rom Backup on to My SD card.
Please Help ME **
have this problem, too can anybody help pleaseeeeeee!!!!!!!!!!!!
What kind of upgrade did you do, sd-flash or shipped-rom? You're now stuck in bootloader.
So try a reset first, maybe it boots. If not put it in bootloader again & do a shipped-rom upgrade (again). If this fails & you still got warrenty use it.
Regards, M
had problem on k-jam, first upgrade just stopped.
started again and all upgraded ok, just restarted the upgrade program.

Need help ! cingular 8125 bricked :(

Hey iam new to this upgrading,CID unlocking etc.
I just bought my Cingular 8125 three weeks before.
I tried upgrading to WM 6.0 The update process completed successfully but after the reboot my mobile was back to factory default with wm 5.0.
without tring the lokiwiz to unlock, i used shelltools to flash the wm6.0.
it was successful, it asked me to do a hard reset.
Since then i am stuck up with the boot screen.
I can't get my Mobile back working.
i tried flashing with the Offical rom but of no use.
i have tried button rom, love rom. nothing works out.
without much knowledge i upgrade my spl & IPL to 3.08
now i am not able to downgrade that too.
tried flashing different roms but of no use, still it stucks up in the boot screen.
the only hope iam having is i am able to get into the boot loader.
I am not sure, where to post this thread, my appologize if i have posted in the wrong page.
below is the information i have on the screen
IPL 2.26
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Some one please help me out. i am very much worried, any help is very much appreciated.Thanks a bunch in advance !
dosai.
Have you tried flashing from the bootloader to an official rom?
thanks for reverting, i have tried that too, but of no use.
Sounds to me like you didn't run the Cert_SPCS and EnableRapi cab files before flashing with ShellTool. Being stuck at the splash screen is a dead giveaway.
I never did understand why someone would attempt to flash a ROM without doing ALL the steps. . .
i did ran Cert_SPCS and EnableRapi cab before running the shelltool. shell tool took around 10 mins to complete the update.after restart, my phone stucked up in the boot screen!. (i remember not unlocking the cid before proceeding with the shelltool) .
is there any way to get the mobile working i am too worried.
Solution
Hi, press and hold the CamShot Button and press the Power button, when you see a multi-color screen you can make a update again.
Hello all Im new here and have the same problem. I followed all the steps and followed all the instructions to fix this problem but nothing. I am stuck on the multi-color screen and i can't do nothing! HELPPPPPPPPPPPP!

ipaq hx2410 help

I have a problem updating my bricked ipaq hx2410(wm2003 se). I'm stuck at the pre-B.L screen. When i ran the rom update, i'm getting the incorrect language! update cannot continue. I tried to reflash windows mobile 2003 se, the progress bar stops at 0.1%, then upgrade was successful .
upgrade Needed: Version 1.00.00 L Language: english, model ID: ipaq hx2xxx
cuurrently Installed: Version "blank" Language: Unknown, model ID: ipaq hx2410.
I also tried the bootloader and getting a blank mtty. Can someone explain to me step by step how to fix this.
Is there anybody that can help me with this problem or redirect me to a link
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
The only way to turn on my ipaq is through the hard reset, otherwise i get a black screen. Is there a trick to turn it on using the normal mode?
Is there any way to bypass the language check? Is my ipaq dead. After i flashed it with AKU,the screen went black at the end of the upgrade(turned off at 100%). Please help.
Thanks for the link. It worked
Varso said:
I had a similar problem with my HX2790 running MW5. I avoided the problem by running the official ROM update for my language. If you run it in normal mode (not pre-BL mode), somehow the software will recognize the correct language, switch to pre-BL mode by itself and will ask you to update or cancel. At that point, if you want to upgrade to 6.1, substitute the nfb file of the ROM upgrade by the WM6.1 otherwise just do the ROM update.
This suggestion might not be relevant as in my case, the ROM version was detected correctly. In your case, the version is blank. I think you should read the whole discussion http://forum.xda-developers.com/showthread.php?t=383173. Many suggested ways to recover a failed upgrade.
Best luck
Varso
Click to expand...
Click to collapse

Cyanogen mytouch HELPPPPPP!

I have a myTouch3G (32B) - I think I rooted it successfully - I got the ROM to install the newest one 6.0.0 (Android 2.2) and its running fine, however I can't get my Google Apps back. I got the zip file as "gapps.zip" on my sd card so that I can just get into recovery and hit Flash from zip "gapps.zip" like I did for installing the ROM, but I CANT get into the recovery mode anymore. I hold "HOME" and "POWER" just like I normally did and all it does is show the slash screen and it says "FASTBOOT" on the top in red, I cannot get to recovery mode anymore! Can anyone help? I just want the market back...OR try to go back to 1.6 and just say f**k it with all these custom roms
You Are lucky to have made it that far. Can't get the gold card to work for me, so i am stuck on 1.6, but a lot of the apps that i want to use need root-or 2.0+. Still no date from T-mobile as to when they will update the line. either way puts us in the same boat with the F**k it thing. YOU ARE NOT ALONE!
Sir plz help me,,,,ahuhuhuu
mY XDA II O2 POCKET PC was no detect ng IMei no...
plz help to have that Imei,,,
ROM versio 1.66.00WWWE
ROM date 02/20/04
Radio version: NO DETECT
Protocol Version NO DETECT
ExtROM 1.66.165
model PH10B
PLATFROM pocket pc
IMEI: NO DETECT
PLZZZZZZ HELP ME....... SIR

Failed to get PMT info, is it bricked for good?

Hi,
So today suddenly my phone restarted and after that it was stuck on the micromax logo, I coudnt get into recovery either. So I tried to flash the stock kitkat rom using sp tools, it did manage to flash it the first time but the phone after that wont start at all, nothing not even the charging screen.
Is it bricked for good? I tried to flash it again but if I choose firmware upgrade or download+firmware upgrade in sp tools I get the pmt info error. Is there any way to get the phone back to a working state? Any help would be much apprecited.
Note: I did look through the old post on the similar topic where the guy managed to solve the problem by using a latest version of sp tools, Im already using the latest version , no dice.
Did you get anywhere with this to unbrick the device as I have similar with a GDP XP and it wont now boot or show charge its just dead!
Any help on fixing this would be great as we cant be alone with this. ATB

Categories

Resources