From this site wm 6.5 toshiba g810 portege is for rom corrected install computer device with a connection was interrupted while I was waiting, and I did not correct the data cable was disassembled after the device was opened what what hard reset soft reset I can not do nothing for the upgrade was done completely right, but my devices boot screen After a more closed will not open, please help.
You must enter in DSUU mode, when turn on phone, HOLD Record button + Volume down button, then press 9 to enter in DSUU, after launch Flash software!
Bye.
My brother dsuu mode phone can not receive in any way will not open key audio recording and sound reduction would press not only the computer bagladıgım When the device is red ışıgı next to the computer does not see the device after a period of light is flashing and the computer sees the device data interface device, install software says
No more idea...... Sorry
Related
Dear all,
My Universal has been stuck in the bootloader screen after upgrade with DOPOD Rom. I have searched thru the threads but have had no luck so far. Has anyone out there experienced this? Please help me out
Thank you
Ken
STUCK RELEASE!?!?!
Well.very easy for start.
ROM Upgrade Failure
It is possible, in a very small number of ROM upgrades, that the upgrade could fail. The following are workarounds to get the device working and upgraded.
Device stuck in 'Bootloader' mode
When this happens the device screen will be blank except for the words:
Serial v 1.00a
The word [Serial] should change to [USB] when the cradle is plugged into the PC, and the version number below this will vary. When you get this screen, a soft or hard reset will not make any difference.
It is still possible to run the ROM upgrade file again, without using Activesync (Activesync will not restart anyway).
• Firstly unplug the USB cradle and reboot the PC
• Plug the cradle back into the USB port (this must plug directly into the USB port and not into a USB Hub / adaptor).
• Now run the ROM upgrade file again from the PC. This should just run as per normal and correctly reflash the device.
If it is still not working,try this
• Press & hold the power button
• Press & hold the Backlight button
• Push the stylus into the soft reset hole - until you see the word [Serial] on the screen.
• You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
It work for me,goodluck
henning
find an attachment how to fix this
Many thanks, HENNING RAS
My device is up & running again. Thanks
Ken
Hi All,
I downloaded Xda_II_172181_Final.exe from the O2 download site and tried to upgrade my XDA II, about 45% into completion my laptop froze and the upgrade software terminated. Now cannot turn on or access my XDA II. Please help!
Many Thanks
Please can someone help me.
I thought this website was the one for all XDA issues.
much appreciated.
tried ?
"1. Start your device in bootloader mode by pressing and holding down:
DPad + PowerButton + ResetButton
After a second release ResetButton, then release the rest of them.
Your screen will show word "Serial" at the top.
You are in bootloader mode now.
2. Place your device in the cradle, ensuring that the cradle
is plugged directly into a USB port on your PC and not to a hub
and that the power supply is connected to the cradle.
It is also a good idea to disable any screensavers on your desktop PC.
Once your device is cradled, the text on the screen will change to "USB".
3. Run HimaUpgradeUt_noid.exe
4. Sit back and wait for the Congratulations screen to be displayed
on your PC. Your device will still be displaying 'Upgrading radio stack, please wait',
but as long as the PC says it is done, then its all OK.
5. Detach your device from the cradle.
6. Now you have to hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
"
Rudegar said:
tried ?
"1. Start your device in bootloader mode by pressing and holding down:
DPad + PowerButton + ResetButton
After a second release ResetButton, then release the rest of them.
Your screen will show word "Serial" at the top.
You are in bootloader mode now.
2. Place your device in the cradle, ensuring that the cradle
is plugged directly into a USB port on your PC and not to a hub
and that the power supply is connected to the cradle.
It is also a good idea to disable any screensavers on your desktop PC.
Once your device is cradled, the text on the screen will change to "USB".
3. Run HimaUpgradeUt_noid.exe
4. Sit back and wait for the Congratulations screen to be displayed
on your PC. Your device will still be displaying 'Upgrading radio stack, please wait',
but as long as the PC says it is done, then its all OK.
5. Detach your device from the cradle.
6. Now you have to hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
"
Click to expand...
Click to collapse
I think this is not the right method, this is for the wm5 bootloader 1.06. Hard resetting is just the power button and the reset button. there is no HimaUpgradeUt_noid.exe in the said installer. I have that installer too!
Hi guys,
Sucess at last!
I have managed to resolve the problem with my XDAII, by going into bootloader mode and re-running Xda_II_172181_Final.exe again. This file had the HimaUpgradeUt_noid.exe and all the other rom image files to do the job.
Many Thanks! - especially Rudegar for his help on.
buzzdev have HimaUpgradeUt_noid.exe
one can use the HimaUpgradeUt,exe too if
one have the same rcode as the rom
or want to do the changes manualy
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
should've used search, this is also a wrong forum for this topic.
with that said, power off the phone, press and hold power, volume down and reset until you see the tri-colour bootloader screen, connect the phone to your PC, you should be able to flash at this point.
do report back.
Japex said:
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
Click to expand...
Click to collapse
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Thanks...
It worked flawlessly....
incredulous said:
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Click to expand...
Click to collapse
When i do this, it still keeps going to the splash. I reset, press vol down, and it continues to go to the splash. If i do it the other mentioned way, power, reset, vol down i get to the tri colour screen.
how to enter in bootloader = press volume down and reset simultaneous !
link
I think my kaiser is bricked somehow. I left it sitting on my charger and came back and it was frozen and now when I turn it on nothing happens except the green light comes on. I can sometimes by messing around with the power plug and battery get it back into android but I cannot even bring up my bootloader anymore. I have no idea if its bricked or whats wrong with it.
Please define messing arround with power plug and battery . Did you try another battery? Battery contacts, miniusb contacts...worst case, something is burned inside. Camera+power+reset doesn't work?
Also, check what was your wife doing before you came back
lol she would never do anything to my phone. By playing with the power plug I mean just plugging it in and taking it out and what not. It's really hard to define it, I would just say ****ing with it lol.
I've come to the conclusion that the radio in my tilt died. Why must my phones always die from a dead radio =( android still works but I can't get into the bootloader anymore and I can't flash a new kernel or even reinstall. Will be nice to see how long this lasts lmao
Can you dump your kaiser to see what is left in our rom?
Follow this procedure to dump your kaiser:
First you have to install QPST (http://www.megaupload.com/?d=OW3ERRNB)
1. Turn on kaiser , now you enter the OEMSBL. You will see nothing on your phone!
2. Your computer will ask drivers for a device if you didn't installed the MotoQ drivers before. Point it to the extracted drivers!
3. If QPST is installed on your computer, disable the com port in the QPST Configurator.
4. Launch mtty and select your com port that is listed as Qualcomm Dignostic Interface 6000 (Comx) in the device manager.
5. Type "h" <Return>
6. if you got any output continue to 7 else pull out the battery, reinsert it and restart at 1
7. type "radata 90000000 1" : Your kaiser is now in loading mode.
8. Close mtty
9. launch the QPST configurator and add the comport and ENABLE it.
10. remove the usb cable of the phone, and reinsert it.
11. your phone must now be listed as Q/QCP-xxx (download)
12. Launch the "QPST Memory Debug" tool to dump smi.bin and ebi.bin
13. Click on browse to select the right com port
14. Click on "Get Regions"
15. Click on "saveto..." to save the files to a directory
16. Zip the files and send it to me.
massivekid said:
Can you dump your kaiser to see what is left in our rom?
Follow this procedure to dump your kaiser:
First you have to install QPST (http://www.megaupload.com/?d=OW3ERRNB)
1. Turn on kaiser , now you enter the OEMSBL. You will see nothing on your phone!
2. Your computer will ask drivers for a device if you didn't installed the MotoQ drivers before. Point it to the extracted drivers!
3. If QPST is installed on your computer, disable the com port in the QPST Configurator.
4. Launch mtty and select your com port that is listed as Qualcomm Dignostic Interface 6000 (Comx) in the device manager.
5. Type "h" <Return>
6. if you got any output continue to 7 else pull out the battery, reinsert it and restart at 1
7. type "radata 90000000 1" : Your kaiser is now in loading mode.
8. Close mtty
9. launch the QPST configurator and add the comport and ENABLE it.
10. remove the usb cable of the phone, and reinsert it.
11. your phone must now be listed as Q/QCP-xxx (download)
12. Launch the "QPST Memory Debug" tool to dump smi.bin and ebi.bin
13. Click on browse to select the right com port
14. Click on "Get Regions"
15. Click on "saveto..." to save the files to a directory
16. Zip the files and send it to me.
Click to expand...
Click to collapse
Would be nice if my kaiser was detecting still... It's weird. It's almost like it has no boot loader but yet it will still sorta boot android.
If the Green led comes on, you are in the OEMSBL. Does your computer asks for drivers when you connect your kaiser to your computer? Ifso, you need the MotoQ drivers (found in this forum) to connect your kaiser OEMSBL to your computer. Then you can use MTTY to talk with it. (if you type something you will not see any output. Only after presing enter/return.
If you need help, let me know.
I've used mtty before. The green led DOES come on but it does not detet at all on my computer. It is not asking for any drivers. When I plug it in nothing happens
then it goes further then the oemsbl.
If it boots Android, it must pass the SPL, so did you try to hold the camera button and then turn on your device? If the SPL tricolor shows, then you can flash. (in theory)
massivekid said:
then it goes further then the oemsbl.
If it boots Android, it must pass the SPL, so did you try to hold the camera button and then turn on your device? If the SPL tricolor shows, then you can flash. (in theory)
Click to expand...
Click to collapse
I've tried to get into the tricolor screen but it is not working with camera + Power and battery insert or on Camera+power+soft reset. I used to have an HTC screen I added display before the kernel loaded. Now the first thing I see is my loading screen for android around a minute or so later only when it's plugged into power.
That's strange. And what is happening when you press the green phone key and powerup? (OEMSBL boot) keep pressing the green button for 5 secs If the green led comes on. Then connect your phone to your computer. Does it appear in the windows device manager?
Does not detect in device manager at all, not even as an unknown device. It's as if nothing was plugged in
If it is not listed as a serial port device. (ports Com & LPT)
then it is not in the OEMSBL. Is your device Security unlocked? If not this can explain why it doesn't enter the OEMSBL with the green button.
Did you also try to put an upgrade file (KAISIMG.NBH) on your root of the SD card?
Maybe this will get launched when your device is turned on?
massivekid said:
If it is not listed as a serial port device. (ports Com & LPT)
then it is not in the OEMSBL. Is your device Security unlocked? If not this can explain why it doesn't enter the OEMSBL with the green button.
Did you also try to put an upgrade file (KAISIMG.NBH) on your root of the SD card?
Maybe this will get launched when your device is turned on?
Click to expand...
Click to collapse
I'll try that out as i've always flashed via usb. Also it is Security unlocked and it is SIM unlocked too.
Nope that did not do a thing. I took a WM rom nbh renamed it to KAISIMG and set it on the root of the SD and it did nothing.
Oh yes, you are right.
in order to load the KAISIMG.NBH, you have to enter the SPL.
hold Camera button and power on. wait 2 secs and unpress the camera button. Then wait for 1 minute, and press the power button again (Power button = start flashing, action key = cancel).
just tried that and still nothing out of my phone
massivekid, i have very similar problem, but my phone turned on.
I dont can turn on bootloader , i try very much metods and any working.
my phone always turn on Smart Mobility i can't change android kernel/back to the windows
few times i tun my pda on blinking yellow led, but computer no see the device
but it still boots into android?
then a jumpspl for android would cure it ;-)
Can you try this one?:
- Remove USB cable/cradle
- Remove battery and re-insert it
- Hold Camera and insert the USB cable.
What do you see now?
The reason why i ask this, is that you have told me that it boots android when you insert the power/usb cable and you see output after 1 min or so when booting android. This behaviour was added to android to let the battery charge...
So the poweron procedure difference from when you press the power button, or when you let the kaiser charge...
hello
i searched the whole internet but there are not much informations about this Phone so i thought i make a new Thread
about the panasonic DCM-CM1 Factory Reset.
please write here any informations and experience you have about the Panasonic DMC-CM1
i never saw someone on youtube google or any other side or anyone who can tell me how to do a Factory Reset with this phone
today i called 5 Panasonic service numbers but noone can help, i also called about 10 Phone Service points for repair no one can help.
i tryed so much with this phone and i finaly found that the CM1 have a Secret key combination to connect it with USB as a Android ADB Interface without having acces to the phone cause it is screen locked.
1 .Turn Phone off
2. press Camera + Volume-up + Power ( Hold )
3. while Holding connect USB. (Hold)
4 .the LED should go green for maybe 2 seconds release all bottons while the led is green before it turns off and then the LED must still green.
then windows found a Android ADB Interface
if im in android SDK Tools i the phone will be found in fastboot!
if i type Fastboot Devices
the other thing i know is how to start in Save mode.
but this is nothing to help with a lost pin.. it only starts the phone without apps that have been installed by the user.
maybe for deinstalling a app or a buggy app.. dont know..
start phone at the screen for the pin or at the home menu..press the power botton hold for 2-4 seconds or so it ask for Shut down Restart and so.. just press and hold Shut down. and then it ask you if you want to start in Save mode. then press yes.
2 weeks ago i wanted to make a Screen lock with a pin for more secure.. i cant remeber the pin anymore thats why i want to make a Factory reset i think im not the only one. so any information would be nice
if there is someone who made Factory Reset with this phone or was able to start in fast boot or anything.. please share the infos with us!
thank you.