Hi there, I hope someone can help me.
The USB connection on my phone as been damaged.
My questions are:
1. Is it easily replaceable?
2. Can i swap it out with any USB Fitting, or does it have to be a Prophet usb fitting?
Kind Regards
Preggie Pillay
PreggieP said:
Hi there, I hope someone can help me.
The USB connection on my phone as been damaged.
My questions are:
1. Is it easily replaceable?
2. Can i swap it out with any USB Fitting, or does it have to be a Prophet usb fitting?
Kind Regards
Preggie Pillay
Click to expand...
Click to collapse
Part is easily repaired, but only to be done by experienced technicians, because the size of the connector is very small ... the USB port and can be replaced with the like which are also widely used by digital cameras and MP3/MP4 Player.
Related
Hi all ...
I'm new here, I'm an electronics Engineer, but I think I got to a dead end with the USB / Charger connector.
it broke 1 year ago and I bought a new connector soldered it with an SMD soldering iron.
everything worked fine, charges fine no problems.
when I wanted to synch it, it refused to connect. I changed the versions to make sure it connects but the PC keeps on saying that the USB device cannot be recognized.
I went through all the pins that I soldered and made sure nothing disconnected or shorted.
all fine but I noticed one thing ... that one of the smd components is missing.
its so small " less than 1mm "
I just need some tips to troubleshoot the problem.
which pins are for serial communication via USB?
any diagram available to help solving this problem?
I have sent it to the agency and they were un able to help ... they just replaced the connector again that it was already working.
device is : i-mate PDA2K original ROM version WM2003se.
Thanks in advance
visit blueangel section of wiki.xda-developers.com. there should be a pin out of its connector.
if you don't care about syncing and only want backup, a simpler solution will be to use SpbBackup or Sprite Backup program that runs on your phone.
good luck
Actually I need the synch facility to upgrade the ROM. I have been using cab files since ages with this pda so synch. is not for downloading appz.
I have seen the pin config. for the car handsfree connector. I think it will help.
still I need some help with the internal schematics the USB +/- Data pins internal schematic.
Thanks
hmmmmmm........ive bin googling the data connection may be this may help.... http://geektechnique.org/images/usb-connector.jpg
hirsty said:
hmmmmmm........ive bin googling the data connection may be this may help.... http://geektechnique.org/images/usb-connector.jpg
Click to expand...
Click to collapse
Thanks for your effeorts, but I was looking for the PDA pins, more percisly is the main board schematic at the pins cuz I think there is a real mess there and I need to trace every pin to fix this problem
Hi,
need to know what type of mini USB is on the circuit ? how many pins?
thanks
All mini USB connectors should be created equal, usb (including usb mini) its what is called an idustry standard, thay have 5 pins total, same shape and size always, I wouldn't even suspect that some connector maker could took off any of the pins out, what surely should be, is that the connector must be a PCB mounting type, it would be a better idea to open the PDA, take off the connector and bring it with you when you buy the new one.
One easy solution -that I think someone in the forum has already mentioned- would be to use another device's mini usb conector (such as a broken bluetooth headset or a memory multicard reader).
hopefully tommorow i'll be able 2 post photo
Hi guys, i have one question. Can i damage my HTC Touch Elfin with non original USB cable. I have one USB to mini USB from my external HDD. I try it ones and it working but want to know if is any chance to damage my PDA. Ty and sorry if i make some mistakes im from Bulgaria.
NBT said:
Hi guys, i have one question. Can i damage my HTC Touch Elfin with non original USB cable. I have one USB to mini USB from my external HDD. I try it ones and it working but want to know if is any chance to damage my PDA. Ty and sorry if i make some mistakes im from Bulgaria.
Click to expand...
Click to collapse
No worries - it's just a standard cable.
I've used 3 non-HTC cables and my Touch works fine. One was even an unofficial PSP cable.
Go nuts and use any USB cable you can find. I have never had any problems in the last year. As a matter of fact. I don't even remember which USB was the one that came with my device.
I have used non HTC cables from eBay, but a couple of them recently stopped working (wouldn't allow ActiveSync). The cable that came with the phone seems to be better quality.
The USB standard is universal, any USB cable will work without damaging the device, as long as the heads match.
hotrod101 said:
Go nuts and use any USB cable you can find. I have never had any problems in the last year. As a matter of fact. I don't even remember which USB was the one that came with my device.
Click to expand...
Click to collapse
same to me but i think that other usb cables sometimes drop connection during active sync
no worries, i use a Nokia usb cabel to my htc
Ehm... No, you should use the one, that came with the Elf. Others do not fit in the spot, but still will work.
Heloo
Any body can plz explain me how to Install wm6.5 on to my Htc touch 3450
I bought it from India and i am now using in Uk with o2 etwork sim
I am new to this forum..
Please some body help me ..Lnks for downloads, usb drivers, Clear pic tutorial and best customized ROM...
I read all the stuff her but lot confused..
Plz help me it would be a great help
Thaking you in advance
Please reply ...
I'm wondering, if I'd want to solder something to the USB port (internally of course) and the attached device is not connected, would I still be able to use the port as before(charging, etc.)? Provided I would not use > (IIRC) 5V together, could they be use simultaneously?
Why I'm asking:
I found an old OCZ Trifecta (SD to USB-Adapter with MicroSD slot) laying around. Stripping the thing down reveals a really thin logicboard, which fits almost perfectly under the normal back cover.
So I thought, if I could wire the USB connector of this adapter to the internal one, I could have additional storage. I don't know if this specific adapter is SDHC compatible, but since there are newer ones around, I could get one of those.
Thus I'm asking for advice:
a) technically possible?
b) if yes, how hard is it for a semi-newb?
c) potential trouble I should be aware of? Not meaning loss of guarantee, more about possible hardware destruction.
Images of the board:
Front
Back
S.D.Richards said:
I'm wondering, if I'd want to solder something to the USB port (internally of course) and the attached device is not connected, would I still be able to use the port as before(charging, etc.)? Provided I would not use > (IIRC) 5V together, could they be use simultaneously?
Why I'm asking:
I found an old OCZ Trifecta (SD to USB-Adapter with MicroSD slot) laying around. Stripping the thing down reveals a really thin logicboard, which fits almost perfectly under the normal back cover.
So I thought, if I could wire the USB connector of this adapter to the internal one, I could have additional storage. I don't know if this specific adapter is SDHC compatible, but since there are newer ones around, I could get one of those.
Thus I'm asking for advice:
a) technically possible?
b) if yes, how hard is it for a semi-newb?
c) potential trouble I should be aware of? Not meaning loss of guarantee, more about possible hardware destruction.
Images of the board:
Front
Back
Click to expand...
Click to collapse
In theory if you rigged it up to work like usb otg and charging then you might be able to get it to work. I think it takes a resistor to trigger it.
mrsatan said:
In theory if you rigged it up to work like usb otg and charging then you might be able to get it to work. I think it takes a resistor to trigger it.
Click to expand...
Click to collapse
No you wouldn't need a resistor, you just need to short pin 4 and 5 together on the micro usb side. That's what makes it an OTG cable. Check out the picture I attached. That should be the wiring you need to make it work. Refer to the link below.
http://tech2.in.com/how-to/accessor...sb-otg-cable-for-an-android-smartphone/319982
In theory it should work. The hardest part is attaching wires to the pins of the micro usb connector. It so [email protected]#$ing tiny... not the easiest thing to do. Unless the pins of the connector goes though the other side of the board, then you can solder onto the solder points itself. That should be a lot easier. Any potential problems? You could screw up your micro usb connector... then you might not even be able to charge it if you lose that...
Good luck. I would be interested to know if you succeed.
BTW Micro SDXC 64GB in FAT32 works in my Acro S running CM10 with Nova Kernel. You can gain a lot of storage!
is it possible to charge mobile while it is in OTG mode?
Thanks for your inputs.
According to this video it doesn't seem to be too easy, guess I'll need to wait a few days for a buddy, I'm not yet skilled enough for such delicate work.
If somebody has more skill and faith in his/her talents, you should be able to get an adapter for <5€ practically everywhere.
Odp: [Q] [Xperia S] Soldering on the USB-Port
webs1821 said:
is it possible to charge mobile while it is in OTG mode?
Click to expand...
Click to collapse
Sure. Just check this thread http://forum.xda-developers.com/showthread.php?t=1822653
Send from my...
Xperia S
mario_666 said:
Sure. Just check this thread http://forum.xda-developers.com/showthread.php?t=1822653
Send from my...
Xperia S
Click to expand...
Click to collapse
Thank you this is what i was looking for
I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB. OK Fine and dandy if I wouldn't be total idiot and wipe system while trying to install new ROM before transferring ROM image to internal storage.
Now I have FLO paper clip able to go to TWRP but can't install nothing. As far I understand there's no way to enable wifi in TWRP.
Any ideas what would needed to be replaced to make my FLO work again so I can put some ROM on it and make it work again.
I'm not sure if USB daughter board would suffice and solve my problem. Any suggestions?
jxl69 said:
I had been somewhat unlucky and while charging my beloved FLO something went puf (literally). After that I don't have any USB connectivity. Charging my N7 works (very slowly), but no USB OTG or USB ADB.
Click to expand...
Click to collapse
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
k23m said:
Either the USB port developed "dry joints" or the wide silver cable (LCM) needs to be re-seated on both connectors.
Disconnect the battery before fixing LCM cable. Here is advice on USB port repair.
Replacing the daughterboard PCB should be the last resort because it is unlikely that the touch function will work 100%. It would work if we had access to the touch calibration software - the problems are described here https://forum.xda-developers.com/ne...rivers-to-calibrate-touch-screen-usb-t3334898
Click to expand...
Click to collapse
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
jxl69 said:
I doubt re-seating would help or cleaning USB port, since it was something electrical happening with that *puf*. If my memory serves me right there was a smell of burnt electronics. I doubt that some shortage disconnected any cables.
Click to expand...
Click to collapse
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
dave457 said:
Sounds like you need a new charging port and board. Easy to fit but difficult to get hold of one. Maybe purchase a broken Flo on eBay and extract the charging port board
Click to expand...
Click to collapse
Even tho charging works? The only problem is data part of USB connection. USB OTG will not work neither will it connect to a PC for file transfer/adb. But if connected to PC or plug device charges. I believe it will not charge past 80 or 90%.
jxl69 said:
Even tho charging works? .
Click to expand...
Click to collapse
Yes