Related
A quick (probably simple) question. I have a CID unlocked Orbit, thanks to imei-check. Does this mean I don't need to use the USPL software now to flash handset or must I still do this first?
Thank you for your time.
Shand359 said:
A quick (probably simple) question. I have a CID unlocked Orbit, thanks to imei-check. Does this mean I don't need to use the USPL software now to flash handset or must I still do this first?
Thank you for your time.
Click to expand...
Click to collapse
If you want update Rom NBH format still need Run USPL again..!
Although it may seem redundant, I would run the USPL before loading any of the roms found on this board as a fail safe. I also have an unlock file from IMEI check and I only use that to load non-modified OEM roms like HTC/O2/Dopod etc. Also remember that you have to run the IMEI check or the USPL EVERY time you change roms. Unlocking once will only serve to load a single rom. So save the unlock utility and the IMEI code file they gave you in a file for quick access if you plan on playing the experimentation game. Also, look through the posts there was a thread on how to unbrick your IMEI-unlocked phone no matter what by doing a trick and a HEX edit involving the software you use to CID unlock your phone.
imei-check vs. USPL
there is following difference with imei-check and uspl:
imei-check recalculates and modifies cid area on your device, uspl doesn't.
with uspl, cid area and model id are ignored and not checked.
this enables to perform upgrade of any rom.
rom has to be properly signed though, if you do nbh upgrade with regular upgrade utility.
if you use pdocwrite method, then it is wise to have uspl installed before you write to doc (same for nbh upgrade. always have uspl installed first). otherwise in case of faulty upgrade it will be quite difficult to recover the device.
keep in mind, with next full rom upgrade (say factory rom upgrade, spl will be overwritten). this means you need to run uspl again, before performing upgrade.
regards.
fdp24 said:
there is following difference with imei-check and uspl:
imei-check recalculates and modifies cid area on your device, uspl doesn't.
with uspl, cid area and model id are ignored and not checked.
this enables to perform upgrade of any rom.
regards.
Click to expand...
Click to collapse
@fdp24,
nice to see you alive and kickin`!
Say, does this mean I could flash the wm6 rom from the hermes (see: http://forum.xda-developers.com/showthread.php?t=305940 )
into my uspl unlocked hero ?
tried it with the implemented installer without success!
greetz
Please answer me this then. Just to see if I have it right.
I have my Orbit unlocked by imei-check. I now have Bepe's WM6 installed and running great with absolutely no problems what-so-ever. Since I have unlocked my phone and flashed a new ROM onto it, do I now need to re-unlock my phone if I intend to change the ROM in the future? (Does flashing Bepe's ROM reset the CID-lock?)
imei-check does permanent cid unlock. you don't need to re-unlock device again.
- some roms will not install on device, because they have different model id.
- uspl is a solution for this. with uspl installed, model id is not checked.
- if you use pdocwrite method, then you are writing directly to doc, and don't have to bother with cid and model id. however, if something will go wrong with this method, it could be not very easy to recover cid locked device. optimal in this case to have device with uspl installed, because you will not be dependent on cid and model id.
- wm6. most of cooked roms represents just an os. during upgrade, ipl and spl parts remains intact during upgrade. wich means with uspl installed, after os upgrade you don't need to install uspl again. spl version is 1.11.0000 when uspl is installed on device.
- regular factory upgrade. all parts are upgraded (ipl, spl, gsm, splash, os). uspl will be overwritten. for future upgrades you need to install uspl again.
regards,
OK Guys,
This is a placeholder for Hard-SPL Dev edition - recommended for ROM Cookers and Developers only.
it's the same as the other except it doesn't require signing and blocks overwriting.
------------------
Done, see next post.
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
here's unsigned version of Hard-SPL - what you've been waiting for!
[size=+1]ok, here it is now as I said the wait would be max 2 weeks in the *worst* case. well the case is much better than that [/size]
this is only for people who know what they are doing!!! newbies who aren't sure what roms to flash, should go with the signed version of hardSPL here: http://forum.xda-developers.com/showthread.php?t=400402
Installation Instructions are the same:
1) Download, extract to an empty folder.
2) Run RomUpdateUtility.exe, Have Phone Synced with PC in Windows Mobile
3) follow steps, check device for prompts after PC shows loading bar. it should go to black screen now.
4) SPL flashes, device automatically reboots, job done.
5) to confirm you got it installed, go into bootloader mode (volume down + reset, i.e. press volume down button and reset then keep holding the volume down key until you see tricolour screen) and verify the screen shows 1.40.OliNex.
note: you will not see the SPL version during normal boot, that is the OS version, not SPL!
INSTALLING THIS WILL HARD-RESET THE DEVICE
TROUBLESHOOTING TIPS:
- read the instructions.
- read the instructions.
- read the instructions.
- Anyone having problems with the device entering SSPL automatically (your device doesn't even go to black screen), please copy SSPLManual.exe to the device and run it. then once the screen is black, run RUU manually (you run the RUU on the PC, if it isn't obvious).
- if you get connection error in RUU after the device goes to black screen, then try a different USB port, also do not use USB hub, you can also try rebooting your PC, and can try using another PC. read the thread for even more tips that I don't remember now. also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- if SSPL-Manual.exe or enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
- CDMA (Sprint or Telus) diamonds need my other hardspl:, head over to: CDMA (not GSM) diamond hardspl - ONLY use this if your diamond does not use GSM protocol for radio!!! otherwise you will brick the device!!!
NOTE: this has overwrite protection, so don't try flashing another SPL using HardSPL.
if someone needs to revert to stock SPL for warranty reasons, we will soon post a stock SPL downgrade package.
enjoy!
UPDATE 1: 1.37 Hard-SPL
for those who need 1.37 due to some screen fuzziness issues on some newer diamonds, here it is with hardspl patches:
- Developer Edition: can flash unsigned code. Version: 1.37.OliNex
- Signed Edition: can only flash preapproved signed code. Version: 1.38.OliNex
please see Attachment below for Developer Edition!!
for Signed Edition, see the signed HardSPL thread of course.
I recommend you flash the original HardSPL, as that one is MFG. only flash the 1.37 if you experience the fuzzy display issue.
UPDATE 2: 1.93 Hard-SPL
if someone's diamond came with 1.93 SPL originally, maybe this HardSPL based on 1.93 will work better than the olders. I have a report that someone has black screen with older SPL's.
but even if your diamond didn't come with 1.93 stock, but 1.37 doesn't fix screen problems (fuzzy screen, flickering, etc.), it is recommended to try this 1.93 HardSPL.
if your diamond works fine with original HardSPL, no need to flash this one.
Version: 1.93.OliNex
IMPORTANT: all in all, I recommend you flash the original HardSPL, as that one is MFG and easier to deal with if there is some problem. only flash the 1.37 or 1.93 if you have screen issues.
if it was some other version and you still have issues after trying 1.37 and 1.93, then let us know in this thread.
STOCK SPL's: to return to stock SPL for warranty reasons: read post #39 in this thread!!!
aborts about 588kb into the download for me.
Hey, Many thanks for all you work, it is working !!
Downloaded and installed fine for me.
Many thanks Oli/Nex
Check ur internet connection. Download is working 100% fine
Good timing, thanks a lot!
lovely....
That was one short 2 weeks
What is the difference between signed and unsigned spl?
Is this working when connecting the Diamond to Vista? I get an app CLOSE/DEBUG exception when I try to run it on Vista (x64). My diamond is the Asia 1.34 version.
Does it work?
Hi Olipro,
Does this one work equally well for SPL 1.23 and 1.34/1.35? There were some discussion about 1.34 locking up the Diamonds with now ways of going back to 1.23? Please advise,
oddball1 said:
What is the difference between signed and unsigned spl?
Click to expand...
Click to collapse
It means you can only install signed ROM's, i.e ones form HTC, Carriers, or ones signed by Olinex and the other people in Elite Team. And they won't sign ranodm crap, so gives you safety- if it's signed, it's ok to flash it.
Unsigned means you can install any random ROM you like, cook your own easily and install it without any fuss.
rorydaredkign said:
It means you can only install signed ROM's, i.e ones form HTC, Carriers, or ones signed by Olinex and the other people in Elite Team. And they won't sign ranodm crap, so gives you safety- if it's signed, it's ok to flash it.
Unsigned means you can install any random ROM you like, cook your own easily and install it without any fuss.
Click to expand...
Click to collapse
Many thanks
Worked like a charm with first click!!! Very good job from OliNex!!!
Thank you very much!!!
loser said:
Hi Olipro,
Does this one work equally well for SPL 1.23 and 1.34/1.35? There were some discussion about 1.34 locking up the Diamonds with now ways of going back to 1.23? Please advise,
Click to expand...
Click to collapse
yes this one works for that too.
Thanks a lot, I believe this is a movement to the right direction.
comnex ..it should be done @ beginning ...
anyway , nice work and congrat
leofungwai said:
comnex ..it should be done @ beginning ...
Click to expand...
Click to collapse
no it shouldnt have been done at all!! but thats another discussion on its own, lets keep this thread on topic people.
Hello everyone I am trying to upgrade my HardSPL by following the guide. I follow all the steps but when it is in the process of upgrading, I get a message stating it needs to be connected. Now, I know its connected as I have activesync open and it shows it being connected. Any help suggestions? I am new at this so I am trying to figure this out. Thanks all!
Try putting device into bootloader mode (soft reset and then quickly press vol. down) then connect it to pc. At the bottom you should see USB. After that, Run the RUU_exe.
can anyone draw me a picture with regards to upgrading the SPL on my phone from 1.40 to 1.93
I know it involves JumpSPL, but it asks for an address???
can anyone draw me a picture with regards to upgrading the SPL on my phone from 1.40 to 1.93
I know it involves JumpSPL, but it asks for an address???
I have the same problem. Any tourtial how to upgrade from 1.40 to 1.93?
I am not an SPL guru, so I could be wrong about this, but this is from the stickys at the top. Under one of the HSPL threads
IMPORTANT: all in all, I recommend you flash the original HardSPL, as that one is MFG and easier to deal with if there is some problem. only flash the 1.37 or 1.93 if you have screen issues.
if it was some other version and you still have issues after trying 1.37 and 1.93, then let us know in this thread.
Just Flash this...
Unpack this and click on the RUU, ensure your device is connected to active sync or Windows mobile device centre.
Should be straight forward enough.
GSM devices only
1.93 HERE
R3PUBL1K said:
Unpack this and click on the RUU, ensure your device is connected to active sync or Windows mobile device centre.
Should be straight forward enough.
GSM devices only
1.93 HERE
Click to expand...
Click to collapse
Just wondering is there any benefit or need to update to 1.93, I am using 1.40 currently and havent had any problems. But not sure if there is a particular reason to change??
So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out
Dear All,
this time, I have a problem and need your help, please.
I just bought a new (used, but not by me ) HTC Touch Diamond. Hard-SPL (1.37 from whoever) was installed.
First MTTY'ed the device - with success (set 14 0, task 29, task 8)
Wanted to install OliNex 1.40 first
Started ROM-Update, everything went fine, screen of Diamond changed into "bar display" - but stays there with 0%
Tried several flashes (OliNex, ROM, Radio - everything the same)
Does anybody have a hint for me what to do? Identifier seems ok, DIAM100 is shown in intial bootloader screen (three color-screen)
I appreciate any hint.
With kind regards from Switzerland - Christoph
Radio
Downgrade your radio to one below 1.02.XXX before flashing the unlocked radio
Full instructions to unlock your diamond are here
http://forum.xda-developers.com/showthread.php?t=749201
Once you have done this, you can flash any ROM you like
Dear Dave,
thank you very much for your support.
Unfortunately it didn't help but showed everytime the same picture - stuck in the bar at 0% and doesn't do anything.
I tried STEP 1, STEP 2 and downgrading to radio 1.00.25.05 (but actually I don't know which is actually installed, as the Diamond never reaches the Touch Diamond page with ROM & HW Info, it stucks in the Touch Diamond page with no information at all, if started not in Bootloader mode)
It seems to me that the bootloader itself could be corrupted or the model number (shows DIAM100 in Bootloader) is somewhat corrupted, as I know that the internal storage consists of more digits (like DIAM10000 or so) - and a way to fix it with MTTY? But I can't find a description of the MTTY tasks of the Diamond.
Any more Idea?
Thank you Dave, and all the others who read and think, in advance.
X
Can you get into Bootloader mode by holding down
Volume down button + Back button (Bottom right button) + Press reset with the pen
Then keep pressed the first two buttons and let go of reset, keep hold of the first two buttons until it reaches the bootloader mode
If you can do this, then reboot and put the radio onto the storage card (4GB one) and enter bootloader mode, then folllow instructions on that screen to flash the radio, and you can do the same for the rom
It sounds to me like maybe you have not managed to flash the HardSPL properly
Hi Dave!
Thanks for your quick reaction.
Yes, I can anter bootloader mode. But nothing more. Flash is not possible. Hard-SPL was the first thing I tried to flash but it also remained at 0%
How can I put files on the internal storage card from within bootloader mode? (Phone is not booting, ONLY bootloader mode is accessible...) I never encountered this before...
But I can reach the phone with MTTY.. can I access the storage card through this?
X
Have your tried different HardSPL versions ?
Im not sure what is wrong... if you are in Bootloader mode, and the USB drivers are installed and you have activesync running on the PC it should update no problem
I would make sure all the above is true, and attempt different HardSPLs
I think that is the issue as you wont be able to flash an unlocked radio or custom rom without HardSPL being flashed first
Here is another version you could try
http://selfmod.net/how-to-hard-spl-a-htc-diamond/
EDIT - And I dont know if there is a way to access the storage card from MTTY or bootloader, my guess is that you wont be able to
Also, this is a GSM Diamond right ? Not a CDMA ? (UK Networks are GSM)
CDMA flash is here
http://forum.ppcgeeks.com/cdma-diam...ond_c-cdma-sspl-hardspl-package-here-now.html
Hi Dave!
Yes, it's GSM. Thanks for your help and the links provided - it didn't help.
I tried various Hard-SPLs: OliNex 1.20, 1.30, 1.37, 1.40 and 1.93 (developers)
Result - all the same: standstill at 0%
I've seen in MTTY that I have an "upload" menu item - but need there the start address and command line for Diamond plus to know what it is meant for, I will try to find out... and if there is some new know-how out of this, I will post it here, in order that future GENERATIONS may find it *laugh*
Dave? THANKS!
Kindest regards from Switzerland - Christoph
X
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
magicdave26 said:
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
Click to expand...
Click to collapse
This is the answer. I used to have the same problem because when I bought my diamond I thought everything runs the same as the TyTN but ...
So to cut this story short, almost 90% of the 0% bar situations are because U R not using signed roms. However if Ya want to then use the unsigned HardSPL.
Hi Dave & Nazgul,
it seems that my case belonst to the non-90%
Of course I tried all this, but I have THREE diamonds - two were branded by the Swiss Swisscom (this is, in fact, the same image as the German Vodafone branding), one was the original HTC version
I'm flashing Diamonds since two years though.
My fault this time was, that I THOUGHT, this new one were HardSPL'ed, but it wasn't - and formatted the device using MTTY without Hard-SPL.
After that I had the above mentioned situation.
NO Hard-SPL was flashable - as written above - also noth the unsigned developer 1.93 edition - it always remained at 0%
I managed in the meantime to flash the original Vodafone/Swisscom ROM. So I have back the device in the official configuration (HTC Swisscom 1.97 package http://www.swisscom-mobile.ch/scm/d...pa=0x0x147x18x0x0x0x0x0&odg=SoftwareAndManual)
But - this uses Radio 1.08.xxx and I would like to downgrade because I think, Dave's hint above to use a radio before 1.02.xxx would be worth a try.
BUT - I STILL can't flash anything. Neither ANY Hard-SPL nor any Radio version nor any ROM.
The bar remains at 0%
I tried to find the original (first edition) of the Swisscom ROM Package, which used the Radio 1.00.25.05 - and then to try Dave's proposed steps.. but I can't find it anymore - all you can find is the "latest" package...
So I would still appreciate any help to be able to flash. Ok, now at least, I have a usable phone... but... I wanted to use it (as the other two) for ROM development testing, so who wants to have a PHONE!?!?
Kind regards from Switzerland - Christoph
Here is your radios
Sorry for the short post, I have a really bad hangover lol
http://forum.xda-developers.com/showthread.php?t=407956
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Christoph21x said:
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Click to expand...
Click to collapse
YEa that might work, it is almost certain the issue is the HARDSpl being either not flashed, or flashed with a signed version
Good luck !!
And the hangover is nearly gone... I cured yesterdays with more alcohol lol
Have you tried these UNSIGNED dev HARDspls ?
http://forum.xda-developers.com/showthread.php?t=400950
Hi Dave - GOT IT, solved
The "secret" was to flash noit from withi boot loader but from within Win Mobile with ActiveSync/Windows Device Center connected.
Then say "Yes" when "enterbootloader.exe" was asked to be installed/invoked.
Then the Device rebooted, flashed Hrd-SPL 1.40 correctly - and everything else onwards went fine.
Thanks a lot for your assitance, Dave and others.
Kind regards from Switzerland - Christoph
Ah.. I thought you were already using the Activesync and CustomRUU to flash it with !
Yes, the ROMs and Radios can be flashed from the storage card, but the Hard SPL needs to be done from Activesync / CUstomRUU
Pleased you got it working anyway