Develop Bugs

Computer fail to recognize the Universal via USB on bootloader mode?

As the title states: Why does some computer fail to recognize the Universal via USB on bootloader mode?
I recently reformatted my computer, which I usually do once a year. After installing all my apps back and running windows update on my computer, I installed active sync. Performed a normal reset on my computer, attached my Universal and active sync worked.
Here comes the problem: I decided to roll back to my old AKU 2 QTEK ROM. Of course, I know how to use the Ma_Upgrade No ID file. The problem is my computer now fails to recognize my Universal no matter what I do on bootloader mode. To make it worst, I am now stuck at the bootloader mode with my computer not recognizing it. Any suggestions as to why my computer failed to recognize my Universal?

OK, I was able to get the ROM upgrade going again, by removing my SIM Card and 4GB SD Card. I'll post back if I was able to revive my Universal.
So it seems that my computer failed to recognize my Universal because either the SIM Card or SD Card is causing the conflict.

I had the same problem.... I have two computers one with Win Vista (with the same problem) and another with XP sp1. This computer recognize my pda in boot loader, doesn't matter if still SD card and SIM inside....
Sorry for my english and I didn't tell you a solution...

Hi,
i had the same (very annoying) problems but i always was able to get the Universal back into Windows Mobile.
It was very strange because i started the ROM update and than e.g. it did not go in the Bootloader but back in Windows Mobile so i started it again and than it stucked in the Bl. Hardreset and putting the device again into Bl did not help and i was already very annoyed. I tried to plug in and out the USB-cable but it was always telling me SERIAL and not USB and Windows showed this ****ing popup that one device is not recognized or something like that. I tried a trick to let the cable plugged in USB and than reset and it showed me USB but wheter MA_Upgrade (No ID of course) nor mtty were able to find the device. After several trys and resetting and resetting again i was able to bring it into USB but MA_Upgrade did not work.
The only way to bring back the device from the Bl is the method described in XDA-Wiki (http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen)
The problem is that this method does work only half. I did the steps until the command "set 14 0" and started MA_Upgrade BUT it always told me that the device is not connected, it never worked. I was already frustrated so i did again the reset and what happend? It started back into Windows Mobile!
So what i think that after using the command set 14 0 AND running MA_Upgrade reactivated the start of Windows Mobile. I tried the steps very often because i tried to find a solution for the contacts between WM5 and AKU 3.2 or higher but the only way is to ActiveSync them. This really works and this is for sure the guaranteed way to get (at least my) the Universal back to Windows.
Btw for the people who are to lazy to use the search function:
The damn ROM upgrade does NOT work on Vista until now! Even not with the Windows Mobile Device Connection Center (or how it's called). I tried several steps on the RTM Vista but it never worked. Don't waste your time on it!
So far from my side, i hope these experience will help some people

I Got It To Work!!!
I was so worried. Wheeeeew! Anyway back to normal again. I got it to work.
My observation is: My computer failed to recognize my Universal because I was using Active Sync Version 4.5 Beta 2 to update my Universal. The solution is to completely uninstall active sync using the windows remove program under control panel, and manually deleting the active sync folder from the hard drive. I then installed Active Sync Version 4.1 and all was well again.
So my next question to all the guys/gals who had problems with upgrading their device because the computer FAILED to recognize their Universal via USB is: ARE YOU USING THE BETA VERSION OF ACTIVE SYNC?

Actually when you try to upgrade with SD card inserted - only then you will get this error - I spend so many hours of GOD prays for my Universal - and after that I just remove a SD card and everything is back to normal

agisofttm said:
Actually when you try to upgrade with SD card inserted - only then you will get this error - I spend so many hours of GOD prays for my Universal - and after that I just remove a SD card and everything is back to normal
Click to expand...
Click to collapse
What is the size of the SD Card you are using? Because when a 2 GB SD Card is inserted, it works just fine. But I experience the error with my 4 GB SD Card.

Unfortunately, i don't share the same luck with all of you.
I've already take out both SD and SIM and try thousand times with ActiVeSync 4.1, 4.2 and 4.5 beta, softreset, hardreset, mtty'ing, but what i got? BIG ZERO.
So my pc always recognise my ppc as "Unknown Device" and there is no, even some slim chance, to get it to work.
Any idea for reviving my uni from black slumber of bootloader screen?
Any help would be appreciated.

DuLanTus said:
Unfortunately, i don't share the same luck with all of you.
I've already take out both SD and SIM and try thousand times with ActiVeSync 4.1, 4.2 and 4.5 beta, softreset, hardreset, mtty'ing, but what i got? BIG ZERO.
So my pc always recognise my ppc as "Unknown Device" and there is no, even some slim chance, to get it to work.
Any idea for reviving my uni from black slumber of bootloader screen?
Any help would be appreciated.
Click to expand...
Click to collapse
use MTTY with "task 28 55aa", "set 14 0", "set 14 9, "set 14 10" and "set 14 20" as described. bootloader screen may be replaced with a blank one, boot it on bootloader mode by "Backlight+Power+Reset"
http://wiki.xda-developers.com/index.php?pagename=Universal_Resets
now upgrade as usual, then If you stuck on the bootloader again after upgrading, try to upgrade the bootloader itself
go to
http://forum.xda-developers.com/showpost.php?p=1255206&postcount=52

i have done all this... but there is something with vista... they do not recognised it when it is on bootlad screen... what should i do can anyone help me??

moixalakix said:
i have done all this... but there is something with vista... they do not recognised it when it is on bootlad screen... what should i do can anyone help me??
Click to expand...
Click to collapse
Hi, yes you could be bang on in saying there is a problem with vista, my machine did that as well, I really thought I'd turned the phone into a brick, luckily I've got an xp machine that let me connect with the tools that everybody else is talking about here, the one I used was UNI_ExitBootloader.exe (from this site somewhere) which sends all the codes for you and it only worked from the xp machine, it totally failed on the vista machine.

Tried all suggestions, but no luck
So a failed upgrade has left my Uni stuck in bootloader mode saying "Serial" and "v1.00". When I plug the thing into my Windoze XP machine with Active Sync 4.5 one of three things happens seemingly at random:
1. My mouse stops working
2. It tells me that the USB device is malfunctioning and cannot be recognized
3. Nothing happens
In all cases the Uni still shows the same "Serial" message.
The Uni has no SD or SIM cards in it. I have tried hard resetting it. I've removed and reinstalled Active Sync. I've rebooted this windoze pile of crap about a thousand times.
Anyone got any ideas?
Thanks,
Saline

Welcome to forums
Have a read here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Hope it helps,

Hi. Thanks for the quick reply. Unfortunately I have already tried the suggestions on that page (that's how I found this thread). As I mentioned above, the device has no similar nor SD in it.

Have you tried to reflash from SD card?
instructions on the link on my sig

Bit of a newb, would like to upgrade but nervous

Hi,
I have done a lot of searches but can't find the answers.
I have a phone bought from Orange. Waiting for Orange to release the latest HTC update will be pointless and HTC won't let me download latest from site.
to install latest official ROM I believe I need to install one of the hardspl's listed on this site (was going for OliNex1.93)
My works PC will not allow USB connection ( I always use Bluetooth) and just tried to install using activesysnc on my home PC but the comms dropped off at the start of the process.
Can I install hardspl from internal storage? If so how?
Once that is done i believe I will be ok.

It would be best to get active sysnc running first. Although there are other ways. I presume you are using XP and running the installer of ActiveSync 4.5 without having your phone attached.
Have you read this HERE

Internal Drive Method: Radio's & Rom's, Yes
HARD SPL ....not recomended to be done via Internal Drive Method!!

welcome to the forum
just follow instructions to the letter and your be fine
have fun

My home PC is Vista and this is were the update started but then stopped.... a few moment of panic but a soft reset showed nothing had been done.
My work PC is XP but trust me 'nothing' will allow USB activesync to work. Can I do it over Bluetooth.
Yes I have read guides.

If you are using Vista - which version? Vista has an alternative to Active sync named "Windows Mobile Device Center" is this still installed on your PC. you should be able to connect your device and WMDC should detect and load the drivers for your device.
I have noticed in the past that some machine require a restart even for the device to be detected. So do this before you connect your device and report back.

Yep using Windows Mobile Device Centre. Perhaps I should qualify. Bit of a newb on ROM updating but pretty technical on PCs and IT level.

Yep using Windows Mobile Device Centre. Perhaps I should qualify. Bit of a newb on ROM updating but pretty technical on PCs and IT level.
Install of hardspl worked 2nd time

We were all in the same boat at one point Happy Flashing

Mmmmm...
Put hard spl 1.4 onto the device successfully.
Ran the upgrade utility on my PC for latest official ROM.
Got to 100% but then got Upgrade ROM code error
Please try again.
Looked this up and forums advised to extract the .nbh file and put onto root of internal storage.
At present I am at tricolor screen trying to browse to storage from XP PC but no joy.
The device says USB and when I connect my PC tells me it is connected but can not find root drive.
Any pointers?

PCPhil said:
Mmmmm...
Put hard spl 1.4 onto the device successfully.
Ran the upgrade utility on my PC for latest official ROM.
Got to 100% but then got Upgrade ROM code error
Please try again.
Looked this up and forums advised to extract the .nbh file and put onto root of internal storage.
At present I am at tricolor screen trying to browse to storage from XP PC but no joy.
The device says USB and when I connect my PC tells me it is connected but can not find root drive.
Any pointers?
Click to expand...
Click to collapse
if you are trying to flash rom from storage card than you don't need your pc. Just rename the nbh to DIAMIMG.NBH and place in root of your storage card. Power on device and it will automatically start the flash process for you.

Problem is I can't locate my storage card to copy and paste the nbh to start the process.

PCPhil said:
Problem is I can't locate my storage card to copy and paste the nbh to start the process.
Click to expand...
Click to collapse
do you have a adapter for your microsd, typically an sd card adapter? if so use that to directly connect storage card to pc and copy-paste

PCPhil said:
Hi,
I have done a lot of searches but can't find the answers.
I have a phone bought from Orange. Waiting for Orange to release the latest HTC update will be pointless and HTC won't let me download latest from site.
to install latest official ROM I believe I need to install one of the hardspl's listed on this site (was going for OliNex1.93)
My works PC will not allow USB connection ( I always use Bluetooth) and just tried to install using activesysnc on my home PC but the comms dropped off at the start of the process.
Can I install hardspl from internal storage? If so how?
Once that is done i believe I will be ok.
Click to expand...
Click to collapse
I feel your pain upgraded my rom to the new one today, Ive upgraded in the past but this was first time with the diamond so i was a little nervous
I had stock 1.93 so i put on OliNex1.93 had a problem but i manged by copying SSPLManual.exe to the device.
Installed the rom no problem.
I also used this since i had issues upgrading to make some changes in the rom not sure if i even had to since i changed my SPL but didn't cause any issues
http://forum.xda-developers.com/showthread.php?t=409425
You will be please when u get the new rom on its faster than the previous official ROMS.
But ya vistas Windows Mobile Device Center can be a pain

In thend I took a deep breath and installed udk ROM.
If I want I can now copy any ROM to my Internal Storage and upgrade.
All worked fine and happy with new device. A big thank you for all help.

Cant downgrade

Hello,
I am trying to get my hermes back to factory settings becuase I want to sell it. But I am experiencing some difficulties. I downloded the original shipped WM6 rom and launced the PDA Phone ROM Update Utility. With my phone conected to active sync, I go through the steps and at the step when they ask the check the boxes, the phone goes into bootloader. At this point the conection with active Sync is gone but my windows still detects it. ( I can hear the sound that plays when Windows detects a device in the usb). I clikc "next" and move along with the PDA Phone RUU. Then the RUU upgrade progress bar appears stuck at 0% and gives me ERROR[260]: CONNECTION.
I have to do a hard reset on my phone to get it to boot the OS.
I have also tried to flash with other ROMS but still get the same error in RUU.
Any help?

What OS are you using? Windows XP? Vista?

If you have Hard SPL V7 on your Hermes use the sd card method.
Format 2Gb or less sd card Fat32. Copy the .nbh file onto it and rename to hermimg.nbh. Put sd card back into Hermes and reset to bootloader. If all is right, follow the prompts.
Cheers...

I've used both xp and vista. still same result.
As far as using the microsd method, I have a 4gb sandisk microsd formatted to FAT32. Im geussing it has to be 2 gb or less?
Im still a little upset that this is happening. It stared doing this after I installed Tai's WM6.5 v9 rom.

On the XP machine do you have .net framework 3.5?
Also, you could try to download a custom RUU.
Cheers...

kallan said:
Hello,
I am trying to get my hermes back to factory settings becuase I want to sell it. But I am experiencing some difficulties. I downloded the original shipped WM6 rom and launced the PDA Phone ROM Update Utility. With my phone conected to active sync, I go through the steps and at the step when they ask the check the boxes, the phone goes into bootloader. At this point the conection with active Sync is gone but my windows still detects it. ( I can hear the sound that plays when Windows detects a device in the usb). I clikc "next" and move along with the PDA Phone RUU. Then the RUU upgrade progress bar appears stuck at 0% and gives me ERROR[260]: CONNECTION.
I have to do a hard reset on my phone to get it to boot the OS.
I have also tried to flash with other ROMS but still get the same error in RUU.
Any help?
Click to expand...
Click to collapse
put your phone in boot loader mode, connect the usb cable, you should then see usb on the bottom of the screen of the boot loader, now load the Rom you want

You forgot to untick "Allow USB Connections" in activesync and to have Hard SPL on the Hermes. If you don't have Hard SPL then you can only flash the Shipped stock rom.
Cheers...

ActiveSync connection not working.... Need to flash SPL

Title explains most of the problem, my phone wont connect to my pc using active sync. If I plug it in, the device shows it is charging, but I cant get anything else, no disk drive, no active sync, no internet sharing. I thought at first it was a USB problem on the phone, but it charges fine on all chargers and even charges on the PC.
so question is, what can I do to make it work and I need to change the spl to .82 (tmobile stock) so i can do a warranty exchange. Any one know if I can flash SPL from sd card like I can on Android devices.
Currently I have spl .79 , the stock winmo 6.5 tmobile rom and latest tmobile radio.

palosjr said:
Title explains most of the problem, my phone wont connect to my pc using active sync. If I plug it in, the device shows it is charging, but I cant get anything else, no disk drive, no active sync, no internet sharing. I thought at first it was a USB problem on the phone, but it charges fine on all chargers and even charges on the PC.
so question is, what can I do to make it work and I need to change the spl to .82 (tmobile stock) so i can do a warranty exchange. Any one know if I can flash SPL from sd card like I can on Android devices.
Currently I have spl .79 , the stock winmo 6.5 tmobile rom and latest tmobile radio.
Click to expand...
Click to collapse
Before you go to extremes, have you you tried changing the USB to PC settings? Try this:
Uncheck the box that says "Enable faster data syncronization", unplug, replug. No dice?

bug666 said:
Before you go to extremes, have you you tried changing the USB to PC settings? Try this:
Uncheck the box that says "Enable faster data syncronization", unplug, replug. No dice?
Click to expand...
Click to collapse
yea, no luck. Ive done a system restore on my PC and all. My PC has been freaking out lately and I am in safe mode right as a matter of fact removing some junk and what not. It will detect the phone, but then when it is installing drivers for it, it ALWAYS fails. no matter what USB port. I have even tried other computers and no luck with that either. I am pretty sure its the USB port on the phone.
so it leads me to my question, can i flash to the .82 SPL from my sdcard or am i pretty much just SOL

Ironic......
I have a similiar but different problem.
I need to do a warranty exchange because my touch screen has stopped working. Unfortunately the last time I used my phone I used internet sharing so now whenever I attach via usb it comes up as internet sharing and it will not let me change it to Activesync. I need to put the stock rom back on the phone so I can send it back. I'm stumped......

phoneoftheday said:
I have a similiar but different problem.
I need to do a warranty exchange because my touch screen has stopped working. Unfortunately the last time I used my phone I used internet sharing so now whenever I attach via usb it comes up as internet sharing and it will not let me change it to Activesync. I need to put the stock rom back on the phone so I can send it back. I'm stumped......
Click to expand...
Click to collapse
All you need to do is boot into the bootloader (turn off the device, then press power while holding [Volume down]), plug the device into your computer, and flash as usual. Just make sure you put back the appropriate stock SPL (which can be found in the HardSPL thread) after you flash back to the stock ROM, if the stock ROM you're flashing doesn't include it. You can verify that you have a stock SPL by looking at the bootloader, since a stock SPL will not say OliNex anywhere.
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.

DaveTheTytnIIGuy said:
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.
Click to expand...
Click to collapse
It wont be detected by any computer. It only charges. For some reason it wont detect as a USB device, it always fails to load the drivers. I am going tomorrow to a DrCellPhone place to have them see what they can do with it, if it is the USB its 25 to get it replaced with a new warranty.

funny, I have exactly the same problem with the same device, everything is working (charge the battery, headphones via mini usb, ...) but I can not sync with my pc. I hoped that I need a special HTC usb cable for that?!
But I assume, that I have this problem due to the fact that I charged the battery with 5V and 2 Ampere ... maybe that has broken one connector?

DaveTheTytnIIGuy said:
All you need to do is boot into the bootloader (turn off the device, then press power while holding [Volume down]), plug the device into your computer, and flash as usual. Just make sure you put back the appropriate stock SPL (which can be found in the HardSPL thread) after you flash back to the stock ROM, if the stock ROM you're flashing doesn't include it. You can verify that you have a stock SPL by looking at the bootloader, since a stock SPL will not say OliNex anywhere.
palosjr: AFAIK, there's no way to flash an SPL via SD card on the Rhodium, or most HTC Windows Mobile devices for that matter. I would highly recommend finding another computer, like one at your local library, to flash the SPL with.
Click to expand...
Click to collapse
Thanks. This worked perfectly!!

Help....going crazy....losing mind :(!!!

My ATT TILT 2 is a broken mess as far as the earpiece and microphone go, so I setup a return to AT&T.
I need to flash the stock ROM. I have it.
I just can't get my phone to connect to damn activesync!!! I have Windows MObile Device Center 6.1 Windows 7 64 bit.
I have uninstalled, reinstalled, everything. Going nuts!
I plug in my phone, select ACTIVE SYNC, then my phone connects and installs the driver "REMOTE NDIS INTERNET SHARING BLAH BLAH" anyway!!!
I uninstalled/removed/disabled this driver, but it keeps coming up no matter what i pick!!?! ANYONE WITH ANY HELP I WILL BE SOOOOOO HAPPY!!!!!
I was supposed to mail this phone back yesterday but I can't even flash the ROM AHHHHHHHHH

You were supposed to mail it back on a Sunday?

You don't need Windows mobile device center to flash.
1. Go into the bootloader.
2. Plugin your usb (you should see usb at the bottom of the phone)
3. Flash true your pc (customruu.exe)
This is way easier then using active sync of WMDC

Lennyz1988 said:
You don't need Windows mobile device center to flash.
1. Go into the bootloader.
2. Plugin your usb (you should see usb at the bottom of the phone)
3. Flash true your pc (customruu.exe)
This is way easier then using active sync of WMDC
Click to expand...
Click to collapse
No, you don't get it. It loads the internet sharing driver no matter what - it will not load the activesync driver.
I know I don't need the software to load a ROM, but the customruu.exe just displays connection errors because it's ALWAYS installed as the RDIM INTERNET SHARING DEVICE

Have you tried flashing via the storage card?
from the FAQ:
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.

Mnementh666 said:
Have you tried flashing via the storage card?
from the FAQ:
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I forgot that existed...I've been so used to flashing thru USB.
Thanks, will try that

redsrule2500 said:
I forgot that existed...I've been so used to flashing thru USB.
Thanks, will try that
Click to expand...
Click to collapse
Is your signature wrong, or did you really flash a LEO ROM on a Rhodium device? Or are you on the wrong forum?

stevedebi said:
Is your signature wrong, or did you really flash a LEO ROM on a Rhodium device? Or are you on the wrong forum?
Click to expand...
Click to collapse
And a TP2 on AT$T?

Unreal. can't do anything. Tried multiple computers, SD Card won't work, this is pathetic.
F this phone

It always always always becomes a modem...on every single computer...>even when i clearly select "activesync" ---- fml!

Finally got it working.
Put Sim Card back in, accepted the network connection instead, connected via Media Net. Then I disconnected, unplugged USB, replugged, then did activesync and it worked.
No idea why. None. It worked. Yay. What a hassle!