ActiveSync Drops When Trying to Upgrade HardSPL - Touch Diamond, MDA Compact IV ROM Development

Hello All,
Please forgive me if any of this post is unclear or is in the wrong place, as I am sort of new to all of this. I HAVE searched, to the best of my abilities, for a resolution to my problem, but I haven't been able to find one yet, so I am turning to the fine xda dev community.
My problem stems from the fact that I am trying to flash the ROM on my HTC Touch Diamond for the first time. I have found a guide online that seems pretty comprehensive and has showed me how to upgrade the HardSPL on my phone first. I follow the instructions which are pretty straight forward and get to the part where I hit "upgrade" and a progress bar appears.
This is the point where I hear the audible sound of activesync disconnecting and the upgrade software comes back with an error telling me to make sure active sync is connected. My phone also freezes at this point and must be soft reset. I have tried this a number of times with the three HardSPL Upgrades the guide gives:
#
Hard-SPL 1.40 Olinex SIGNED
Hard-SPL 1.40 Olinex Developer Edition-unsigned
Jockyw2001's 1.23, 1.24, 1.34 Hard-SPL
The result is always the same.
Any suggestions or work arounds for this?
Thank you very much in advance!
-Matt

Gordo293 said:
.......Any suggestions or work arounds for this?-Matt
Click to expand...
Click to collapse
Try putting your Diamond to bootloader manually and flash the unsigned Oli/Nex HSPL. And search .. again for instructions. Good Luck..

Related

[UPG]Hard-SPL Unlocker - Developer Edition

OK Guys,
This is a placeholder for Hard-SPL Dev edition - recommended for ROM Cookers and Developers only.
it's the same as the other except it doesn't require signing and blocks overwriting.
------------------
Done, see next post.
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
here's unsigned version of Hard-SPL - what you've been waiting for!
[size=+1]ok, here it is now as I said the wait would be max 2 weeks in the *worst* case. well the case is much better than that [/size]
this is only for people who know what they are doing!!! newbies who aren't sure what roms to flash, should go with the signed version of hardSPL here: http://forum.xda-developers.com/showthread.php?t=400402
Installation Instructions are the same:
1) Download, extract to an empty folder.
2) Run RomUpdateUtility.exe, Have Phone Synced with PC in Windows Mobile
3) follow steps, check device for prompts after PC shows loading bar. it should go to black screen now.
4) SPL flashes, device automatically reboots, job done.
5) to confirm you got it installed, go into bootloader mode (volume down + reset, i.e. press volume down button and reset then keep holding the volume down key until you see tricolour screen) and verify the screen shows 1.40.OliNex.
note: you will not see the SPL version during normal boot, that is the OS version, not SPL!
INSTALLING THIS WILL HARD-RESET THE DEVICE
TROUBLESHOOTING TIPS:
- read the instructions.
- read the instructions.
- read the instructions.
- Anyone having problems with the device entering SSPL automatically (your device doesn't even go to black screen), please copy SSPLManual.exe to the device and run it. then once the screen is black, run RUU manually (you run the RUU on the PC, if it isn't obvious).
- if you get connection error in RUU after the device goes to black screen, then try a different USB port, also do not use USB hub, you can also try rebooting your PC, and can try using another PC. read the thread for even more tips that I don't remember now. also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- if SSPL-Manual.exe or enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
- CDMA (Sprint or Telus) diamonds need my other hardspl:, head over to: CDMA (not GSM) diamond hardspl - ONLY use this if your diamond does not use GSM protocol for radio!!! otherwise you will brick the device!!!
NOTE: this has overwrite protection, so don't try flashing another SPL using HardSPL.
if someone needs to revert to stock SPL for warranty reasons, we will soon post a stock SPL downgrade package.
enjoy!
UPDATE 1: 1.37 Hard-SPL
for those who need 1.37 due to some screen fuzziness issues on some newer diamonds, here it is with hardspl patches:
- Developer Edition: can flash unsigned code. Version: 1.37.OliNex
- Signed Edition: can only flash preapproved signed code. Version: 1.38.OliNex
please see Attachment below for Developer Edition!!
for Signed Edition, see the signed HardSPL thread of course.
I recommend you flash the original HardSPL, as that one is MFG. only flash the 1.37 if you experience the fuzzy display issue.
UPDATE 2: 1.93 Hard-SPL
if someone's diamond came with 1.93 SPL originally, maybe this HardSPL based on 1.93 will work better than the olders. I have a report that someone has black screen with older SPL's.
but even if your diamond didn't come with 1.93 stock, but 1.37 doesn't fix screen problems (fuzzy screen, flickering, etc.), it is recommended to try this 1.93 HardSPL.
if your diamond works fine with original HardSPL, no need to flash this one.
Version: 1.93.OliNex
IMPORTANT: all in all, I recommend you flash the original HardSPL, as that one is MFG and easier to deal with if there is some problem. only flash the 1.37 or 1.93 if you have screen issues.
if it was some other version and you still have issues after trying 1.37 and 1.93, then let us know in this thread.
STOCK SPL's: to return to stock SPL for warranty reasons: read post #39 in this thread!!!
aborts about 588kb into the download for me.
Hey, Many thanks for all you work, it is working !!
Downloaded and installed fine for me.
Many thanks Oli/Nex
Check ur internet connection. Download is working 100% fine
Good timing, thanks a lot!
lovely....
That was one short 2 weeks
What is the difference between signed and unsigned spl?
Is this working when connecting the Diamond to Vista? I get an app CLOSE/DEBUG exception when I try to run it on Vista (x64). My diamond is the Asia 1.34 version.
Does it work?
Hi Olipro,
Does this one work equally well for SPL 1.23 and 1.34/1.35? There were some discussion about 1.34 locking up the Diamonds with now ways of going back to 1.23? Please advise,
oddball1 said:
What is the difference between signed and unsigned spl?
Click to expand...
Click to collapse
It means you can only install signed ROM's, i.e ones form HTC, Carriers, or ones signed by Olinex and the other people in Elite Team. And they won't sign ranodm crap, so gives you safety- if it's signed, it's ok to flash it.
Unsigned means you can install any random ROM you like, cook your own easily and install it without any fuss.
rorydaredkign said:
It means you can only install signed ROM's, i.e ones form HTC, Carriers, or ones signed by Olinex and the other people in Elite Team. And they won't sign ranodm crap, so gives you safety- if it's signed, it's ok to flash it.
Unsigned means you can install any random ROM you like, cook your own easily and install it without any fuss.
Click to expand...
Click to collapse
Many thanks
Worked like a charm with first click!!! Very good job from OliNex!!!
Thank you very much!!!
loser said:
Hi Olipro,
Does this one work equally well for SPL 1.23 and 1.34/1.35? There were some discussion about 1.34 locking up the Diamonds with now ways of going back to 1.23? Please advise,
Click to expand...
Click to collapse
yes this one works for that too.
Thanks a lot, I believe this is a movement to the right direction.
comnex ..it should be done @ beginning ...
anyway , nice work and congrat
leofungwai said:
comnex ..it should be done @ beginning ...
Click to expand...
Click to collapse
no it shouldnt have been done at all!! but thats another discussion on its own, lets keep this thread on topic people.

Orange HTC touch diamond ROM update

Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you
I suggest your search the forum...
hello newbie
yes use the search button...it works really well
You first need to flash your diamond with one of the hard spl on this site and after you've done that you can take your pick from any of the roms on here
sorry guys i did look just didnt understand much. I am trying to use Hard SPL just cant get it to work.
same here
I have an orange htc Diamond and would really apreciate which files wouldwork. Everything I have tried stay's at Zero and ends up in an error.
Any help would be greatly ppreciated
root directory
to use hard spl i have to put a file in the root directory! but what is the root directory?
Hi James, your failing at 0% most likely because the SPL your using will not allow unsigned ROM's. Look for another SPL, one with developer edition in the title is good and works quite well for me.
I have an Orange also, the first thing to do is install the SPL then flash the radio (.05 is good) then get a new ROM!
Hope this helps
i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?
james soules said:
i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?
Click to expand...
Click to collapse
You need to do the following
1. Download the Unsigned HardSPL 1.24 from here http://forum.xda-developers.com/showthread.php?t=408621 and extract to a folder on your PC. Make sure you have Active sync installed and setup with your Diamond. Run the Updater in the 1.24 folder. Once the Phone reboots reconnect with active sync.
2. Download any of the ROMS on here and run the ROM to flash the phone.
Thats it !!!!!
Topboy
as i go to add a ROM i get a error saying the application failed to initialize properly ( 0xc0000135) click OK to terminate
Or check www.modmydiamond.info for easy to understand information
i get the above error as i try to add RUU
Hard SPL won't work
Hello,
From what I've read on the forum and also on www.modmydiamond.info, I gather I need to go through the Hard SPL step before installing any ROM.
However, after trying 2 different SPLs (hard_spl.120 and diamond_hspl_1.24) it still doesn't work.
I'm stuck at 0%.
Thanks
Read here....
As an alternative to the other threads try this one:
http://forum.xda-developers.com/showthread.php?t=416211
Its about the most comprehensive writeup I've seen to quickly and easily get your Diamond set from HardSPL to Radios to ROM's
Also read the WiKi's section at the top of the forum......
Query on Orange htc Upgrade ROM.
Hi There,
I have recently purchased a htc diamond, it was originally an Orange unit but is unblocked.The ROM version is 1.37 but I wish to flash to 1.93.I have the Orange released version of the 1.93 as htc wont support me direct.Question is, if I do this will the unit revert back to being Orange??ie.....does this flash the radio back?? or will it remained unblocked??
Thanks in advance...
james soules said:
Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you
Click to expand...
Click to collapse
thxthxthxthx

diamond won't upgrade to 1.93 hspl

I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
...unfortunately no ideas, just the same problem described here already: http://forum.xda-developers.com/showthread.php?p=2927161#post2927161
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
I have the exact same issue... I tired updating it from 1.24 to 1.93 and it restarted like it updated it. But when I go into boot loader its still got the old hardspl.
Does anyone know why??
I have tried searching around for a solution but no luck
I'm no noob and i've flashed 100's of times across many fones and unbricked a few with some careful reading but this seems very odd and stupidly simple. No idea what i'm missing.... only thing i can think to try is to flash from internal storage, but i would think this unwise with the hardspl as I thought hardspl would control access to the internal storage like some sort of bios perhaps?!
Same here
Hey guys,
Does anyone knows what is the resolution for this? I having the same problem as well.
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
i have almost same problem but the only difference that my Diamond don't have hardspl on it and whenever i try to flash any hardspl phone stops at 0% and stays there for a long time....I want to change my Diamonds language...So can anyone suggest me solution.....I have already posted here on forum but no answer yet!
http://forum.xda-developers.com/showthread.php?t=749664
Another little question that how i can flash hardspl via internal storage and where its root???Root is the device path which we seen as drive in computer when we use mass storage or any other?
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
Thank you. used this and it worked
Hi everybody,
got yesterday another diamond, after mine died some time ago. It has 193 spl and I cannot upgrade to olinex spl. It runs through everything, but upon reboot it still has the original 193 spl. Any ideas? I really need to flash, mine speaks Dutch and I want it in English. Please help. Kind regards. Ben

Newbie questions with upgrading HardSPL

Hello everyone I am trying to upgrade my HardSPL by following the guide. I follow all the steps but when it is in the process of upgrading, I get a message stating it needs to be connected. Now, I know its connected as I have activesync open and it shows it being connected. Any help suggestions? I am new at this so I am trying to figure this out. Thanks all!
Try putting device into bootloader mode (soft reset and then quickly press vol. down) then connect it to pc. At the bottom you should see USB. After that, Run the RUU_exe.
can anyone draw me a picture with regards to upgrading the SPL on my phone from 1.40 to 1.93
I know it involves JumpSPL, but it asks for an address???
can anyone draw me a picture with regards to upgrading the SPL on my phone from 1.40 to 1.93
I know it involves JumpSPL, but it asks for an address???
I have the same problem. Any tourtial how to upgrade from 1.40 to 1.93?
I am not an SPL guru, so I could be wrong about this, but this is from the stickys at the top. Under one of the HSPL threads
IMPORTANT: all in all, I recommend you flash the original HardSPL, as that one is MFG and easier to deal with if there is some problem. only flash the 1.37 or 1.93 if you have screen issues.
if it was some other version and you still have issues after trying 1.37 and 1.93, then let us know in this thread.
Just Flash this...
Unpack this and click on the RUU, ensure your device is connected to active sync or Windows mobile device centre.
Should be straight forward enough.
GSM devices only
1.93 HERE
R3PUBL1K said:
Unpack this and click on the RUU, ensure your device is connected to active sync or Windows mobile device centre.
Should be straight forward enough.
GSM devices only
1.93 HERE
Click to expand...
Click to collapse
Just wondering is there any benefit or need to update to 1.93, I am using 1.40 currently and havent had any problems. But not sure if there is a particular reason to change??

Flashing can't start, and cant't find solution the after searching the forum

So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out

Categories

Resources