Develop Bugs

Trouble with Dopod WM6..

can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..

To me said invalid device id, and got stuck on the boot loader

try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck

update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?

It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000

racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...

Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.

IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL

well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?

You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.

yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..

new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl

mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??

Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!

I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..

Flashed my mine in a breeze from LSVW version 27/05/07.

myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz

mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....

geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that

try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release

Vogue Stuck at HTC Screen

Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%

Planetneo said:
Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%
Click to expand...
Click to collapse
Check PPCGeeks, there is a thread with factory ROM's.

Try doing this check your registry under HKEY_LOCAL_MACHINE\Software\Arcosoft\ArcSoft MMS UA\Config\mm1\MMSCsettings\make sure you only have one entry: Cricket MMS if you have another named Default or Sample, delete them and then try again; if it fails Delete all, soft re-boot and then install your ROM. Good luck.

Planetneo said:
Hey Guys,
I was trying to flash ToO's Cricket Rom to an HTC Sprint Vogue and after the process was finished it is stuck on the "HTC Smart Mobility" screen. I used an unlocker by cokeman before flashing I I think I need to re-lock the handset to flash it back to the original sprint ROM. However I need the older sprint rom and not the new one with GPS. When I put the phone in bootloader mode this is what it says:
It says:
VOGU100
SPL-0.41 Coke
CPLD-3
Where can I get the older ROM for the sprint vogue?
Update:
I am not able to load the original Sprint ROM. It errors out everytime at about 29%
Click to expand...
Click to collapse
I'm a little confused on the issue. If you want to flash roms with GPS you need to be unlocked with Imcokes 2.31 not 0.41 unlocker. Once unlocked you can flash to the stock roms. I flash back to Sprints stock GPS rom all the time. Be careful of flashing from a GPS rom back to a non GPS rom. This could cause some issues.
If you are trying to relock your phone thats a different issue.
EDIT: After rereading. Did you try flashing from a non gps rom to a gps rom or vice versa? Your phone looks to be unlocked with a non-gps unlocker. Is the cricket rom GPS?

When flashing a custom ROM your Vogue needs to be unlock with 2.31 (GPS) or .40 (non GPS). Not too sure about cricket but would assume if you have a radio version of 3.xx.xx would be GPS. Hopefully you have not bricked your Vogue.
You may find more help at ppcgeeks.com or ppchaven.com.
You may have to resort flashing your ROM in the bootloader mode,

SAME PROBLEM with Vogue
I think I have the same problem as the one who started this thread. here is what I did:
I unlocked a Vogue with the non-gps unlocker (SPL-0.41.Coke)
then I loaded a GPS rom onto the phone (OMJ 3.09)
and now it is stuck at the HTC Screen.
I then tried to flash a stock ROM to the phone, but as descreibed above it will not fully load- it stops at 29 percent- tried it a couple times.
I then tried the OMJ 3.09 again and it still stuck in HTC Screen, and says "No radio.'
I am trying to figure out what to do. I was told by someone to load a GPS radio into it and see if it boots. I have the radio to install but not sure if thats best bet.
I was told by someone else to install nongps radio and then install a nongps rom.
One concern I have is that I will brick my phone that way (if i try to downgrade to a nongps radio after installing a gps rom...but im not sure that the gps rom actually installed a gps radio or not cuz my phone was only .41 unlocked)
Also, I cant seem to install a stock rom because it stops at 29 percent.
Any ideas?
Thanks

found answer
to anyone else with this problem- I just installed this rom: http://forum.xda-developers.com/showthread.php?t=357762
and all was well including radio.

Just thought that I would post what happened to my phone and the steps that eventually recovered it in case it helps somebody else:
My phone was stuck with "No Radio" on the boot loader screen and the SPL as "SPL-2.31.CoKe", but none of the 3.x ROMs would flash properly that I tried. So here are the steps that eventually recovered it (mostly...):
1.) I installed the ROM above from the tri-color screen (power+camera+reset). I still had no radio, but it was letting me past this and booting up to WM.
2.) I then re-flashed the 2.31.CoKe boot loader (not sure if this step is necessary but listing what worked...)
3.) I tried to install RUU_Vogue_VZW_WWE_3.14.605.1_Radio_3.37.78_Ship.exe but it failed at 10% restarting to RUUNBH screen and the installer gave me Error [290]: Invalid Command
4.) I then tried to install the latest sprint ROM straight from the HTC site:_Touch by HTC (Sprint)_RUU_PPST_Vogue_SPRINT_WWE_3.03.651.4_2_Radio_3.42.30_AM_NV_2.04_Ship this looked like it was going to fail at the same part the Verizon rom did as it rebooted at 10% to RUUNBH screen, but the Sprint installer did something (I heard the computer lose and gain connection multiple times) and eventually it went right back and continued on from 11% and finished successfully.
5.) Rebooted and I had a radio now! Rather then risking trying to install the Verizon ROM again I went straight to the custom ROM I had originally started out with: NFSFAN 6.5 V6 which is working fine for me, except the GPS which is what started out my adventure of the last 3 days...
Just a note: for all flashes except the final one I simply waited till it was at the "Tap the screen..." stage till flashing. I never let any ROM but the final one run it's customization.

some1 please help

I have read and read and read. so I have a telus diamond and I cannot flash hardspl 1.4. I tired xp and vista. I ended up flashing 1.57 (comonex?) and I tried flashing the radio and it didn't work. I try flashing 1.40 but it gives me communication error and an enterbootloader error on the device. any ideas before I smash this thing?
thanks

what did you do? maybe you describe step by step what you did and what was the result

megagprime said:
I have read and read and read. so I have a telus diamond and I cannot flash hardspl 1.4. I tired xp and vista. I ended up flashing 1.57 (comonex?) and I tried flashing the radio and it didn't work. I try flashing 1.40 but it gives me communication error and an enterbootloader error on the device. any ideas before I smash this thing?
thanks
Click to expand...
Click to collapse
make sure your using the CDMA hard spl and not the GSM
your also required to have .net CF 3.5 installed in order to flash hard spl.

where is the cdma hardspl? isn't that unsigned_1.4 hard spl... from the tutorial?
I flashed 1.57 on it and its hard to even get into the boot loader with the volume down/reset. sometimes it doesn't boot and just vibrates. sometimes it boot into wm6.1. I hardly can ever get it into bootloader then when I do and I flash a radio 1.0.5.25 (?i can't remember which right now) it says it flashed, resets and is still 0.99.99v. I wanna flash a good radio and the juicy telus rom because straight out of the box the gps has never work properly and the phone always messes up.
thanks guy

talking to myself
ok so i found this enableRAPI and CERT_SPCS cabs that disable the security warning (that comes up when i try and get into bootloader and makes the device freeze solid)
goin to try when my girl gets home

megagprime said:
where is the cdma hardspl? isn't that unsigned_1.4 hard spl... from the tutorial?
I flashed 1.57 on it and its hard to even get into the boot loader with the volume down/reset. sometimes it doesn't boot and just vibrates. sometimes it boot into wm6.1. I hardly can ever get it into bootloader then when I do and I flash a radio 1.0.5.25 (?i can't remember which right now) it says it flashed, resets and is still 0.99.99v. I wanna flash a good radio and the juicy telus rom because straight out of the box the gps has never work properly and the phone always messes up.
thanks guy
Click to expand...
Click to collapse
your worrying me, your not researching before your doing all this stuff and your going to bring your phone.
there are NO radio updates for the telus diamond. flashing any other radio will brick your device.
you MUST unlock your device with the CMDMA unlocker its not on xda its founds here
and you MUST make sure any rom files are CDMA based and not GSM.
may i suggest you first research the difference between CDMA and GSM cellular devices, and then i suggest reading very carefully. as some users here who do not have already bricked there devices. knowledge is key.

talkin to the walls again
Juggalo_X said:
your worrying me, your not researching before your doing all this stuff and your going to bring your phone.
there are NO radio updates for the telus diamond. flashing any other radio will brick your device.
you MUST unlock your device with the CMDMA unlocker its not on xda its founds here
and you MUST make sure any rom files are CDMA based and not GSM.
may i suggest you first research the difference between CDMA and GSM cellular devices, and then i suggest reading very carefully. as some users here who do not have already bricked there devices. knowledge is key.
Click to expand...
Click to collapse
thanks so much for the info, thats the .57 hard spl i have flashed, good thing the radio didnt kill it
thanks again
i have flashed my titan and have a good new radio and it works mint, why no cdma radios?
thanks again

Please Really Need Help for Flashig / Upgrading

Hi!
I am totally new to HTC Diamond. I got my set from England (Orange). It was locked. I was able to unlock it with the free solution available. Ok. Now the problem is I heard about TouchFLO but it I can't seem to activate. What can be the reason and what can I do?
Second, mine says it has :
ROM Version: 1.37.405.1 WWE
Radio Version: 1.20.OliNex
IS it ok. Or can I get a new more better version. Whats with radio version? Please guide me what can I do? I right now have no idea. I tried the tutorials as well but I am confused.

thats not the radio version, thats the SPL (Service Provider Lock).
and its a Hard SPL, which i presume you flashed to 'unlock' it.
the Hard SPL lets you flash a different ROM (but voids your warranty) it doesnt SIM unlock it tho.
TF3D (Touch Flo 3D) should run automatically when the phone is started, if it doesnt, go to Start> Settings> Personal tab> Today> Items tab and make sure "TouchFLO 3D" is checked.

Old ROM
thornofcarrion said:
Hi!
I am totally new to HTC Diamond. I got my set from England (Orange). It was locked. I was able to unlock it with the free solution available. Ok. Now the problem is I heard about TouchFLO but it I can't seem to activate. What can be the reason and what can I do?
Second, mine says it has :
ROM Version: 1.37.405.1 WWE
Radio Version: 1.20.OliNex
IS it ok. Or can I get a new more better version. Whats with radio version? Please guide me what can I do? I right now have no idea. I tried the tutorials as well but I am confused.
Click to expand...
Click to collapse
The ROM version you're showing here is really old (as ROM's go!). You can get a link to the latest Orange ROM (v1.93) here, or flash one of the superb cooked ROM's in this forum

grahamkdt said:
The ROM version you're showing here is really old (as ROM's go!). You can get a link to the latest Orange ROM (v1.93) here, or flash one of the superb cooked ROM's in this forum
Click to expand...
Click to collapse
Thanks a lot. But flashing with v1.93 will not do anything bad with the set. I once tried to upgrade my Imate jamin and it went dead and was not repaired. So I am a little hesitant you know.

you have already voided your warranty by flashing a Hard SPL. i would suggest flashing it back to the original, then flashing the latest Orange ROM (its not supposed to be too bad).

mugglesquop said:
you have already voided your warranty by flashing a Hard SPL. i would suggest flashing it back to the original, then flashing the latest Orange ROM (its not supposed to be too bad).
Click to expand...
Click to collapse
Thanks a lot. Could you please further tell me how to flash it.

read the tutorial in the stickie.
lots of reading

Thansk. Just tell me which is the latest and best version that I should use?

did u even look at the other threads? ....
4 threads down from yours:
http://forum.xda-developers.com/showthread.php?t=457980

Ok ok man. i got it myself without looking them thanks. But now I have this problem that messages are not being sent. i tried soft reset and hard reset but no avail. What could be the reason for that? B
By the way I upgraded it with 1.93 flash given above in this thread.

Try the new 2.00 ROM.
You can also try one of the smaller lite ones
(Swtos, Panosha), each time followed by a HARD reset (backup your Internal Storage data first).
If THAT doesn't work, you might have an SMS configuration/operator issue.
A.

messages not sent
make sure you have set the phone to your service provider....in connections

Flashing can't start, and cant't find solution the after searching the forum

So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.

1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?

Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.

Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"

Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.

johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?

djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1

What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.

Great!
Glad it all worked out