Develop Bugs

Phone Pad Vibrate

Edited an old cab to remove the version limits. It now works on Wm6.
Install and then dial a number from the standard phone dial pad to test! You should feel a short vibrate when you tap a number button letting you know that it's been tapped.
Add it to your CAB file collection.
Cheerio
Howard

What exactly does this do, with Phone Pad? Sounds interesting

It vibrates shortly each time, you press number in dial pad... or I guess, coz it did not work on my TyTN
but mayby is problem with some SPB products, because I have lot of them installed in my TyTN... e.g. phone suite, which can manipulate automatically with sound, vibration and light according to profile settings...

YUP! When you go to the dial screen and tap a number a small vibrate lets you know that a button has been pressed.
I'm also using bunches of SPB programs, but I still get the Vibrate from the standard dial screen.
Cheerio
Howard

sinmae said:
It vibrates shortly each time, you press number in dial pad... or I guess, coz it did not work on my TyTN
but mayby is problem with some SPB products, because I have lot of them installed in my TyTN... e.g. phone suite, which can manipulate automatically with sound, vibration and light according to profile settings...
Click to expand...
Click to collapse
It works on my Hermes but you have to long-press the key. Press for at least a half second to get the vibrate motor spinning.
Also, be sure to set either "short" or "long" tones in the phone options. It won't do anything if set to "none."

Hey thanks for converting to WM6 I had been missing it for awhile now!

Any chance this will work in WM5? Please and thanks.

Yeah this is soooooooooooo useful tip man, thanks a lot !!^^

Uninstall Issues...
I liked the idea, just didn't like the fact that you have to push the button for so long to get hte vibrate to react, just a fraction longer and it turns into a speed dial. So let's talk about the uninstall....
I unstalled the app, everything went normal. Now I have no keypadd tones at all.
hshortt, can you provide a fix or provide the registry keys that this install/uninstall modified?
EDIT: Nevermind, fixed on my own...

Works with the HTC Touch / Vouge. Just had to do a soft reset twice. For some reason after the first time, the touch screen stopped responding.

I'd like to know what you did to get your keyapd tones back, this program sucks!!!

chibull17 said:
I'd like to know what you did to get your keyapd tones back, this program sucks!!!
Click to expand...
Click to collapse
Here is the solution I ended up putting together.
http://forum.xda-developers.com/showthread.php?t=353295
there's a download and some instructions down in the post...

smittyofdhs said:
Here is the solution I ended up putting together.
http://forum.xda-developers.com/showthread.php?t=353295
there's a download and some instructions down in the post...
Click to expand...
Click to collapse
guys i have tried the solution in the above link, it didnt work out.
if i exported the registry files from a non screwd device, and exported to my mine... will it work out?

This program is not very effective, cause when I tap out a phone number naturally I tap it quickly, and you have to hold for at least 300ms (I reckon) for it to even do a little vibrate.
it somehow needs to be much more sensitive, lower ms or something. Maybe its a limitation of the whole vibrate mechanism in the phone anyway.
Oh well.

Lost All Sounds
after installing i lost all sound output from my back speaker
no music, no ringtones, nothing
it only made my phone pad vibrate but screwed up all other sound output
tried to uninstall & still no fix
also hard reset & gflashing ROM again didnt fix
did it screw up my device completely !!!!!!!!!!
any fix please???

Vibrate dial pad
Thank you ! This is just what I was looking for

Sorry.Didn't find how to delete message

Hi pretty neat program, until I found a better one TouchResponse... This one allows you to even select the vibration time, and it vibrates on every tap on your touch screen. Well the problem is I un-installed Phone Pad Vibrate and now the the sound is gone when I press a phone number. The link for the fix isn't working, so how do I fix it so I can get the sound back???

Did the link for removal instructions get moved/removed for this?
The link from above is still broken. Anyone have instructions on how to remove this app?

could someone upload it on rapidshare, because i can´t load it, thank you

[UTIL]In Call Screen Lock Like Omnia

This tool acts like a screen locker during all call.
From start of dialing until call ended.
It locks only screen and does not turn off the screen.
This one is very useful to see how call going but dont have any troubles about accident screen taps. And every moment you can unlock screen to press something. Hardware buttons does not locked.
Warning
This util hooking touch screen driver.
So you need first install SDKCERTS.CAB from attach
Also, if something will wrong with this hooking, you can return full functionality to touchscreen only by disabling tool touchscreen driver.
You can do it, using PC tool pregutil from XdaUtils.
You need to make ActiveSync connection with phone and then run:
Code:
pregutl.exe -d HKLM\HARDWARE\DEVICEMAP\TOUCH :DriverName
then SoftReset the phone.
In any case, Hard Reset will restore your phone.
Problems with installing driver make that touch screen will not have any response for taps.
I have using this tool on Polaris,Diamond and Blackstone. I have not any problems.
BUT: you are using this tool at YOUR OWN RISK
Instructions
0. Make a backup of your phone
1. Install SDKCERTS.CAB
2. Install HtcExtFun-0.3.cab from attach
3. Soft reset
Features
this tool can:
- Lock screen during all call
- Change alerting of new sms recieved event
- Alert about missed calls and messages
- Turn off screen when call connected
- Vibrate when call connected
- Vibrate every n-th second of the call
- Simple redialing of current call if connection does not reached
- Screen off during dialing when phone flicked. Used g-sensor
- Change SIP (software on screen keyboard) when stylus in/out
All settings in registry. HKCU\Software\HtcExtFun
Registry keys description included in install folder.
To apply changing settings need restart program: run HtcExtFun.exe from install folder and say YES, then run program again.

it looks great man, pls share to us

look nice. plz share

me too........

Yes please share this!

looks very intreseting

Waiting, waiting anxiously!!!

The same with key lock ?
Nice soft but if the key doesn't lock there is still a high chance to press the end call button by accident. There is absolutely no way at all to lock keys as well ?
Thanks

I'm waitng too.
I'm want to try your app.

jeah pls share this =)
it looks very useful for me

waiting here too

Hi. I would like to have it too.
Where did you get it from?

slider
this app is stupid you cant answer the phone with the onscreen slider

Is this for qvga devices too and how stable is this?

arnaud.ja said:
Nice soft but if the key doesn't lock there is still a high chance to press the end call button by accident. There is absolutely no way at all to lock keys as well ?
Thanks
Click to expand...
Click to collapse
Check my sig for the in call key lock

has anyone used this? can someone comment on how it works? been looking for something exactly like this. thanks

in stalled it with the new energy rom rom and had to hard reset my pure. when i had it on another rom it worked just fine. after i installed it i rebooted my phone and it would not even boot. it just got stuck on a black screen.anyone else have the same prob?

leemoss84 said:
in stalled it with the new energy rom rom and had to hard reset my pure. when i had it on another rom it worked just fine. after i installed it i rebooted my phone and it would not even boot. it just got stuck on a black screen.anyone else have the same prob?
Click to expand...
Click to collapse
Darn was just about to use this and then I read this!
Im on MM rom War.
Any1 have success using this?

I tryed it with Duttys 6.5 rom and i had to hard reset. I to wish it would work.

Had a black screen on boot, watched the thread and finally found that it's not compatible with Energy ROM
Too late

Screen going White on Kavana 6.1 Work Around (edited)

I wanna make another post here cause in the last post this issue wasnt resolved and i wanna fresh thread here, please only post if you have the solution, thanks hope theres someOne who can get this issue resolved.

Do you use AutoKeylock ?
I had this problem when I started using 6.1 ROMs first.
In my case I had about 6 applications I always installed right off the bat after a new ROM flash. One of those was Maniac's AutoKeylock.
I timed the duration between answering a call and having the call go white one day, and it seemed to me to match precisely with the screen timeout settings I had in AutoKeylock.
I removed the application, and have never seen the problem happen again.
However, I do miss having AutoKeylock.
I realize that this could be totally coincidental, and thus I asked before whether others who had the problem also used AutoKeylock but never got a reply.
Perhaps you can reply as to whether you use it or not. And, if you do, whether removing the application resolves the issue for you.
If there is a correlation then we can alert Maniac to the issue, and he may be able to find a solution.

LiverpoolFCfan said:
I had this problem when I started using 6.1 ROMs first.
In my case I had about 6 applications I always installed right off the bat after a new ROM flash. One of those was Maniac's AutoKeylock.
I timed the duration between answering a call and having the call go white one day, and it seemed to me to match precisely with the screen timeout settings I had in AutoKeylock.
I removed the application, and have never seen the problem happen again.
However, I do miss having AutoKeylock.
I realize that this could be totally coincidental, and thus I asked before whether others who had the problem also used AutoKeylock but never got a reply.
Perhaps you can reply as to whether you use it or not. And, if you do, whether removing the application resolves the issue for you.
If there is a correlation then we can alert Maniac to the issue, and he may be able to find a solution.
Click to expand...
Click to collapse
You know if the reason you miss autokeylock is for the ability to set a time for the screen to turn off and the keypad to lock, smarttoolkit does that, with no problems.

HTCP4000PPC said:
I wanna make another post here cause in the last post this issue wasnt resolved and i wanna fresh thread here, please only post if you have the solution, thanks hope theres someOne who can get this issue resolved.
Click to expand...
Click to collapse
How often it happen?
With my phone running Kavanas I will get a white screen once after a reboot and then I press and button and it goes back to normal and wont do it again. I have gotten used to it.
For some reason I think it has to do with Tornado PowerControl, do you have that installed? I just cant figure it out exactly. Maybe we can find a solution.

We'll i believe this White screen has something to do with the backlight settings in power managment, i find if you leave screen on full and turn off the phone from turning off the screen, the white screen wont happen, this isnt so bad, cause if u want the screen to go off just hold down the disconnect phone button, not too bad cause when your not wanting to use the phone anymore the screen still goes off, also you can turn the backlight off in accessories which is the same as setting the screen to go off automatically in 5 seconds, white screen fixed moreless.

Same issue with Ricky's v24 and now with Rose 1.7
I also am experiencing this issue, but do not have installed neither Maniac's AutoKeylock nor Tornado PowerControl.
It happens sometimes during a call, sometimes not.
It happens when leaving the phone unlocked and timesout idle time. If hit the Home or back buttons, it shows the home screen again and next timeout does work fine.
I have beeing looking up and down for fixes but was unable to find one. Some say turning off "Run Lowlight" JOGGR setting, some say flash after a hard reset...
It seems that running lowlight (joggrinfo.exe -m -t) helps a bit. If the phone is fully bright and rests on the table, the screen goes white after timeout.
However, if run lowlight and let it alone, it turns off the screen normally.
Also when it goes white and hit back or home button, the screen goes mid-bright, and then turns off normally.
However, when unlocking, it goes full bright, and then the issue comes back.
In summary ...
Full Bright -> Times out to whitescreen.
Mid Bright -> Times out to lights off.
Unlock -> Goes full bright -> Times out to whitescreen.
White screen -> Hit Back/Home button goes mid-bright -> Times out to lights off.
It would be great if lowlight could be run when unlocking the device.
Does it work same way for you guys??
Regards.

This will stop White Screen from happening.
ok this is a way to avoid the white screen issue, (Click on Light Config) then open CeleTask and in CeleTask - Tools use Close Screen this will turn off your screen and allow the backlight from turning on when screen turns back on, also remember u need to set your power settings to (Backlight time out on battery 5 Seconds and Backlight on AC can be 1 minute which u never use) and Display time out Never..)
You can also use CeleTask to disable the screen when you make a call, just open CeleTesk when you hit call.

Topic should be changed as not a fix but work around "sortof":
Process of illimination:
My recomendation would be try a hard-reset, don't install any programs see if that fixes it now when installing programs don't bung them all on install 1 @ a time soft-reset give it while see if problem resumes, do this for all software then you may find the culprit?
This is not an issue faced by all so something has to be the culprit.
Bad Flash?
Software Install?
JOGGR?
Power Settings?
They are just examples.
I had this happen once but on WM6 and a hard-reset was what was needed and didn't pop up again........

HTCP4000PPC said:
ok this is a way to avoid the white screen issue, (Click on Light Config) then open CeleTask and in CeleTask - Tools use Close Screen this will turn off your screen and allow the backlight from turning on when screen turns back on, also remember u need to set your power settings to (Backlight time out on battery 5 Seconds and Backlight on AC can be 1 minute which u never use) and Display time out Never..)
You can also use CeleTask to disable the screen when you make a call, just open CeleTesk when you hit call.
Click to expand...
Click to collapse
These instructions have fixed my device... I got an Elf and I made it my primary phone, and now I´m experiencing new ROM´s in my S621. This problem happens in my device (the S621, of course), and I´m now using NRG remade by Ricky and Stylez, and this problem with the screen seems to be solved with this tip.
This problem does not happen when I use "Kavana remade by Ricky and Stylez" only with NRG and it´s Remake.
Regards

If this isnt helping try just disabling Timeout and set everything else ur way u want.

Any way to keep screen off all the time until top power button pressed?

More than half the time I take my phone out of it's case in my pocket to check texts or call somebody, it's always on and eating battery. Alot of the time I have the phone in vibrate or silent because I can't have it going off most of the day, and whenever I get any kind of notification the screen comes on (text, alarm, call, ect.), and then the screen ends up staying on because it's constantly being bumped and never has the time to shut itself down.
Is there any way I can make the screen stay off at ALL times (except on an incoming call), and ONLY come on when I press the unlock/power button on the top of the phone?
I have a TMobile TP2 and I'm running the Nov. 19th, Photon Energy ROM. Upgrading to the Nov. 27th version when it's done downloading but I don't think that will fix the problem as I've changed ROMs before. Thanks to any help.

you will find that when in the case it should be off, on taking the phone out of the case (i assume the HTC one that came with the phone?)
the magnet in the case triggers the keyboard sensor which turns the screen on.
otherwise, you can change the display time out in power options under settings.
Cheers
Steve

That's interesting, I've heard about the case doing that but never thought about it. Would you recommend any cheap cases, or is there a specific magnet location I should be careful of? And do you know if there is a way to keep the screen off when I get a text message for example?

There is a way to fix this... it is to disable "Wake on Slide." I have done this and no more problems.
Here is a link to what to do:
http://forum.xda-developers.com/showpost.php?p=2945249&postcount=3
Hope it helps you, as it did me.

Thanks for the reply and I appreciate the help, but I don't really have a problem with the wake on keyboard slide, it seems that if the phone is in my pocket locked, and I get a text message, the screen comes on to notify me that I have a text message. Then, it's usually being bumped around in my pocket and since the touch screen is usable with any object, it will stay on because something will tap it in my pocket. The phone then heats up over time and drains battery. I want to find a way to keep the screen off at all times unless, I either receive a call, or push the power button. Thanks.

illusion of progress said:
Thanks for the reply and I appreciate the help, but I don't really have a problem with the wake on keyboard slide, it seems that if the phone is in my pocket locked, and I get a text message, the screen comes on to notify me that I have a text message. Then, it's usually being bumped around in my pocket and since the touch screen is usable with any object, it will stay on because something will tap it in my pocket. The phone then heats up over time and drains battery. I want to find a way to keep the screen off at all times unless, I either receive a call, or push the power button. Thanks.
Click to expand...
Click to collapse
Try:
go to HKLM\Drivers\BuiltIn\RIL
change DisableSMSWakeUpEvent to 1 (0 will wake up the device)
On my Rhodium, it does not wake up by default. I hear the notification, but my screen remains dark
Or try this cab file ... soft reset after install

Thanks for the .cab, I'm restarting now to see if it fixes the problem. Kind of random, but I might as well ask here before starting a new thread. I started using Mobile Shell instead of TF3D and so far I love it, but when setting a wallpaper, the wallpapers that I would normally use in TF3D, (480x800), it makes me select or crop out part of the photo to use as a background in Mobile Shell. I can't tell if it actually gets blurry (I would think so, because it's stretching the picture), but does anyone know why it wants me to only use a certain portion of the background instead of just setting the entire picture? Thanks,

More than likely, the version of Mobile Shell you have is either not designed for WVGA or there is a setting somewhere in there that allows you to change it and you haven't found it yet.
Am not a expert on mobile Shell, but according to their website, the latest version (3.5) does support WVGA.
Another option is to, if you have Adobe Photo shop or something similar, scale down the entire picture to the size it reccomends.
Otherwise, if you have a version earlier then 3.5, maybe you could upgrade and see if it makes any difference.

Quick Tilt 2 Question !

Hi,
I have a Tilt 2 with stock ROM. The only two enhancements I use is "S2U2" and "Advanced Configuration Tool" ! I changed someting and now have a little problem :
When I get an incoming call and the caller id with the pic pops up, I can't pickup the call, using the green on-sceen button. This button does NOT pickup the phone call. I have to use the green hardware button to pickup the incoming call. However, I can use the RED on-screen button to end the call.
I soft reset the phone a few times and tried some settings with the "S2U2 and Advanced Config. Tool", but I can't get it to work.
Any ideas ?
I'd appreciate any help and suggestions.
Thanks,
JCE

same thing is happening to me, neither the onscreen slide, or the hard button work..
can't wait for an answer -_-
i lurk this forum here and there, and i still don't understand anything...at all -_-

jerzey_devil said:
same thing is happening to me, neither the onscreen slide, or the hard button work..
can't wait for an answer -_-
i lurk this forum here and there, and i still don't understand anything...at all -_-
Click to expand...
Click to collapse
Haha, it takes time to understand all the jargon and such that takes place around here. Just do some reading and searching, don't be afraid to ask questions if you can't find a thread explaining it. Eventually I would suggest flashing to a good rom like one of the Energy Rom's or a Cell Rom. The two best Rom Cooks on the Rhodium (Touch Pro 2/Tilt 2) side of xda.

I say the same thing as doublen1, use a non-stock ROM because these come with features already installed and you will be able to use S2U2 and all that stuff. and about the actual issue, I have had problems picking up calls with the screen, so I just started using the hardware keys.

Make sure you didn't mess around with any of the touch screen settings in Adv. Configr or BSB tweaks or something like that. This usually causes the problem with the dialer.

Hi AllTheWay,
well, I don't remember changing anything in the "Advanced Config. Tools" which would cause the touch screen settings to be different. However, I might have done or changed something...... Is there a way to get the "Touch Screen" settings to a default level without hard resetting the device ?
Thank you.
JCE

jce2005 said:
Hi AllTheWay,
well, I don't remember changing anything in the "Advanced Config. Tools" which would cause the touch screen settings to be different. However, I might have done or changed something...... Is there a way to get the "Touch Screen" settings to a default level without hard resetting the device ?
Thank you.
JCE
Click to expand...
Click to collapse
Not that I know of off the top of my head. There might be a setting inside of Adv Config that would allow you to restore to default. Also the S2U2 has a setting to take control as the dialer screen when somebody calls. You can try messing around with the settings in S2U2 as well.
PM me if you don't find an answer soon.