Hi,
I've got problems with these two buttons:
- the downward direction in navigation button is not "clicking", it stucked, doesn't move at all.
- the red receiver button "clicks" but there's no effect on the phone.
I have opened BA ang managed to check out the button board. The metal circle which corelates with downward button doesn't clikck and the red one looks fine.
In this case would changing button board fix the problem? Other buttons work fine.
How much more or less cost button board? Is it possible to find used one?
Cheers.
Related
Hi guys,
Here is my dream situation:
- Double tap "Hang Up" button to lock the device (I understand this can be done with AEButton Plus, although I haven't tried yet)
- Screen will turn off after a while
- Unlock the device by swiping the finger
At no point are the hardware buttons pressed! My new cover makes touching the power button very hard
Is this possible???
Thanks
They problem, as I am sure you've realized, is that once the phone enters suspended mode the digitizer is disabled (touch) and so are all other non hardware buttons.
I've always had problems with the power button on the HD being a pain in the neck to find and hit, so what I did to rectify this was cut a small hard plastic sticker to the size of the power button and stuck it on there. This helps a lot in not only finding the power button but also pressing it.
(Sticker was a liquid crystal thermometer sticker made by OMEGA: product number RCL-8050/150 I found this to be the perfect width, so I cut off a 1mm sliver off the end)
If you were really stuck on making this work exact as you described, you could prevent the phone from shutting down and just turn off the screen.
(I'm unsure of how the different screen off programs effect the digitizer, my guess it they all disable it at the same time, but I'm sure all that could be seperated.)
However since only the screen would turn off not the device, you'd drain the batter, and its short life would make this not worth it.
Alternate solutions:
Instead of doubletap hangup which you could do through AEButton Plus, but longpress end key can do the same thing just instead by holding the end call key
Also, you configure your phone to wake up at the press of any hardware key, IE the volume buttons on the HD.
Seen here
Also, you configure your phone to wake up at the press of any hardware key, IE the volume buttons on the HD.
Seen here[/QUOTE]
Could you please upload the Keylock Zip file?
On the AT&T version (Tilt2), with the cover removed, there is a white button between the camera and the battery. Does anyone know what this does? It's not the soft reset button on the side.
Is it the speakerphone microphone mute button?
Now I feel dumb.
You're right. It's the button that the button on the cover depresses. It must be getting late. Thanks!.
Hello, so I have old blue angel device (XDA IIs) and power button broke(it's not on the plate). I have soldered button from nokia, but button doesn't seem to work.(button physicaly is ok) 2 tracks on the pcb are broken(2 last ones) if someone has schematics, or knows power button ways, maybe you can give me a photo with them? in the worst case I think photo of pcb where's power button, and other side in macro mode(HQ) would be enough.
UPDATE: Thanks for help everyone(sarcasm). Managed to repair myself.
Hi All,
My unit is the 7" double din with the captive touch buttons on the left (Power, Back, Vol up & Vol down).
I was going through the factory settings and played with the touch calibration settings. I was attempting to remap my power button to something else, but all I have managed to do is remove all mapping for these 4 buttons.
When I go in to the section to re-map these, pressing the buttons has no effect.
I saw a couple of videos where after re-calibrating the touch screen (top left then top right) the mapping page for these buttons comes up, this doesn't happen on mine (maybe because Android 8?)
Can someone please let me know what I have to do to get these buttons back to how they were?
Cheers,
Kris
https://youtu.be/b7kEy4XzQX0
Maybe I was getting that second screen and just going straight to "save exit".
It was very late by the time I got to this point. I'll try again soon and report back.
Thanks.
The above worked. Thanks again.
Hello, on y previous phone I could switch the way the bottom buttons on the screens are displayed. I would indeed like to have the back button on the right (instead of left). I didn't find how to do it. Does anybody know? Tx!