Hi,
Few day ago my artemis p3300 got crazy.
it's make random reset, sometimes isn't boot up after reset, it stuck on black screen. or it's coming up and then reset again.
it's also stuck few times on vibration mode. and it's only stop with soft reset.
suddenly I can't turn on WIFI , it's always stay off .
I Try this roms in the last 2 days :
manila 2D pdviet 33 - 36
b&b v 5.0
last I returned to touch 4.02 and I still have no wifi and it's stuck.
I also try to change the radio firmware...
should I throw it ? there is something to do ?
try
1-flash wm5 ship ROM
2-CID Unlock
2-Flash your favourite ROM
U should be OK
i tried to install the original HTC ROM but i still get error #24 - "invalid device id" or something similar. at the moment i can get the tri-color screen by pressing the voice button and soft reset and that's it. when i try to soft reset normally i get a blank screen. plz help?
TIA
finally it's back...
thanks.
I found other Original ROM . I installed it and it work fine.
Then , I installed Manila 2D again and now after I change my Radio Ver, My gps and GSM are working good.
the last thing that no working is WIFI. i can't turn it on!
how do I know what radio version are fix for my device ?
thanks
royis said:
thanks.
I found other Original ROM . I installed it and it work fine.
Then , I installed Manila 2D again and now after I change my Radio Ver, My gps and GSM are working good.
the last thing that no working is WIFI. i can't turn it on!
how do I know what radio version are fix for my device ?
thanks
Click to expand...
Click to collapse
You may also want to try buying a new battery if your device is old. I've seen Wizards act wierd when the batteries go bad. But they usually get swollen - battery pushes out the battery cover.
Also, have you opened your device lately? I had a problem with my reception after I changed my housing. There are small connectors that have to be bent out to touch their corrasponding spots on the circuit board for FM Radio, GPS, Wifi, ect. Have to make sure they touch the right spot.
And of course, it could just be a bad flash. Reflash and try different radios. That's all I can think of.
my wifi is not working too. After manila 2D, and i try old rom, new roms, the newest radio but not working.
Related
Worked ok last night, then it crashed (mad colours on screen), so I had to do a FULL restore of radio and rom (seemed to be stuck in bootloader).
So, reinstalled everything, all good, I just cannot get it to turn on WIFI. I go into comm manager, click on wifi, and it tries to turn it on, then comes back with a X next to the icon.
Also the front today screen plugin (the wifi/bluetooth one) doesnt say WIFI: off anymore. Just has Bluetooth:Off
Any ideas
THANKS!
Try to flash back the rom again..
By the way, what rom do u used?..
I only just flashed it again ..
I used the O2 rom 'Xda_Exec_Upgrade_v1.30.162'
Can you recommend another ROM that might fix it?
Also, does reinstalling a ROM reinstall all the drivers? As I've noticed some things stay resident even after a flash; call timers for one..
thanks
while im waiting for replies, im going through roms
trying different AKU ones now from the ftp
could it be a radio issue?
My QTEQ 9000 are on the same situation, made some stripes on the screen and now can´t detect anything!!
The wifi apears I start it but can´t get any signals!!
Any help please?????
i upgraded radio to 1.14 and still same
Try these ROMs
You can find on the forum, Ivan's and Helmi's ROMs.
They are the latest AKU 3.2 and seems to work just fine as O2 ROMs are just AKU 2.X!
I think the problem lies deeper than a hard reset/rom as well, it must do after installing 3-4 roms, and a couple of radios.
Yes ive tried UNI_AKU3_5_WWE_IVAN_Test2 ROM as well.
Same.
Anyone else got any solutions as to what it might be?
installing the latest qtek rom off buzzdev now, includes full radio/rom/ext rom. if this doesnt work, then f**k it, ive spent enough hours on it, and i'll just get a new one on contract tomorrow.
thanks for the people that replied
what about the driver disk, isnt there a wifi thing on there
maybe im dreaming
Have a look in the network adapters list and see if the Tiacxwln card is listed, if not sounds like it is a hardware rather than a driver problem. It's not unheard of for computer hardware to fail for apparently no reason. This is likely if you have tried different ROMs and none of them work.
I´ve tried upgrade radio to 1.14 and I tried Ivan's and Helmi's ROMs.
and the problem persists!!!
Tiacxwln card is listed.
Strange situation because during one year worked very well and suddenly make some stripes on the screen and now don´t detect nothing!!
Maybe antenna problem??
Help us??
Is there a problem with o2 official rom?.. Heard few people also got a problem if flashing to o2 rom..
Nope, not working, tried qtek roms, a new orange rom, still wifi not coming on.
Yes the card does show in network cards.
Oh well
Any help Please???????????????????????????????
I have a imported DIA100 phone, and trying it on the T-mobile network here in the states. everything was fine up until today when i upgraded my phone to the 1.93 series, now it randomly shuts off, and it cannot connect to the T-mobile network, keeps saying (searching). I don't know what's going on, I reflashed the device and it still does the same thing, infact it might even be worse now. Restarting the phone doesn't work, as it keeps restarting from the boot. Anyone have any idea what to do? I'm going back to 1.35.
Intradvocate said:
I have a imported DIA100 phone, and trying it on the T-mobile network here in the states. everything was fine up until today when i upgraded my phone to the 1.93 series, now it randomly shuts off, and it cannot connect to the T-mobile network, keeps saying (searching). I don't know what's going on, I reflashed the device and it still does the same thing, infact it might even be worse now. Restarting the phone doesn't work, as it keeps restarting from the boot. Anyone have any idea what to do? I'm going back to 1.35.
Click to expand...
Click to collapse
i too have many problems with 1.93.456.2 WWE baserom. somehow, it just doesn't seem so stable ... not sure if many others are feeling the same for 1.93 roms. i guess 1.37.456.2 ME WWE is still the most stable at the moment...
if only we can have a review on all official rom consolidated in one thread.
Sprite?
Did you use Sprite to backup your previous rom and store it in 1.93xxx?
This could be the cause.
ruffruff said:
i too have many problems with 1.93.456.2 WWE baserom. somehow, it just doesn't seem so stable ... not sure if many others are feeling the same for 1.93 roms. i guess 1.37.456.2 ME WWE is still the most stable at the moment...
if only we can have a review on all official rom consolidated in one thread.
Click to expand...
Click to collapse
Yes i had same problems. imo the 1.93 isnt a stable rom(yet) so im back with 1.37.456.2 this one is just perfect,very stable,less memory leakage.
Well, the problem is still on going. I can't flash my phone anymore for some reason, even though I've tried both, unsigned and signed Hard-SPL, which both of them flash fine. However, the phone gives me error [276] update error. So not sure what exactly is going on here.
Also, no, didn't sprite backup, phone's just being retarded, mobilecityonline will repair it, but it will take almost 4-6weeks, I cannot wait that long. What else should i try?
Okay, nope not fixed... Flashed it with 1.37, connected to the network for a few seconds, dialed somebody and no ring or anything, but when i called my phone i could hear my own voice. So I guess i have to send it in for repair. Damn.
berlinberlin said:
Did you use Sprite to backup your previous rom and store it in 1.93xxx?
This could be the cause.
Click to expand...
Click to collapse
Could you please detail? I've flashed 1.93.xxx just in the day it appeared on the site and after flashing, I've restored the backup made with Sprite Backup to preserve the settings and so on. I wasn't worried about the contacts/calendar since I have them in Outlook, but I didn't want to start all over with settings, install programs and so. I've made the restore in "upgrade mode", restoring also the databases. The result was that I got a verry strange TF3D, displaying "Home" between the operator name and date, and strange behaviour. I've seen also that the animations were taken out so I've flashed back 1.37.xxx.3. Could be any problems generated by the restore operation? Should I use a different restore type (eventually not selecting "restore databases")?
I have had no problem with the new 1.93xx rom.
Touch FLO 3d is quicker (probably because the animation is disabled)..
and the battery life is about 20% better
Radio ROM Anyone
Sounds like the Radio...
What version is everyone on? The 1.93 ROM updates the Radio, have you tried downgrading to 03?
mhbr12742 said:
Sounds like the Radio...
What version is everyone on? The 1.93 ROM updates the Radio, have you tried downgrading to 03?
Click to expand...
Click to collapse
I am on 05 and has no problem ( have been using it for a day now)
I don't know, but If i plug the diamond into my adapter, the network suddenly works and I can actually make calls and everything's fine and dandy, but just on the battery, I can't call anyone, and if I pull out the adapter when the phone gets a signal, the signal stays but again, can't call anyone because i can't hear anything.
It's an awkward problem. I'm not sure if it's my battery or something. So I'm getting another battery off ebay since they don't sell HTC Touch Diamonds in the U.S. yet.
I've been having random freezes with the 1.93.xxx
Anybody else experienced that?
A.
adwinp said:
I've been having random freezes with the 1.93.xxx
Anybody else experienced that?
A.
Click to expand...
Click to collapse
Yes, me I had same problem twice - freezes on PIN input screen, second problem with this release is that sometimes PIN screen doesn't appear. Now I'm back on 1.37 and everything seems to be ok
Intradvocate said:
I have a imported DIA100 phone, and trying it on the T-mobile network here in the states. everything was fine up until today when i upgraded my phone to the 1.93 series, now it randomly shuts off, and it cannot connect to the T-mobile network, keeps saying (searching). I don't know what's going on, I reflashed the device and it still does the same thing, infact it might even be worse now. Restarting the phone doesn't work, as it keeps restarting from the boot. Anyone have any idea what to do? I'm going back to 1.35.
Click to expand...
Click to collapse
THe Problem you've encountered:
1. Random auto reboot
2. Random freeze
3. etc.
It's sounds familiar to me. Well it's maybe have to do with SPL just like the Kaisers do.Well, I said maybe... So, what we did to our Kaiser before is flashing the HardSPL which has the same version number as the ROM flashed. So, if you're using ROM 1.93 then the HardSPL should be flashed is Olinex HardSPL 1.93 or you can try one by one of the developed HardSPL existed in this forum. My saying is, go with HardSPL 1.93 and see what happen. If it's still no go then it must have to do with the ROM itself.
Just my 2cents.
Hi all,
My Diamond is acting weird lately; sometimes (so far it seems at random) when I turn on the device (from standby), the display is grey'ish / scrambled, and nothing works. I have to removed the battery to get it working again.
This happens with all ROMS found here (haven't tried stock rom yet).
Anyone know what this might cause?
I'm running dev. edition SPL from olinex...
Any tips would be greatly appreciated!
/edit; Could this be SPL related?
Maybe perform the hardSPL again?
Reform the battery for a minute. After this hard reset your device a few times.
If this doens't fix the problem use your original ROM and send the device back for repair.
Would be my solution
I have the same problem. Diamond swiches to standby mode and does not resume or just the light switches on and the screen is blank. Sometimes, it even switches off while booting. All the time, I have to remove the battery. And after some "battery remove resets", the error seems to occur more and more often. It also suddenly looses the phone signal but immediately finds a new one ofter 1-2 seconds.
I think it is somehow related to the phone chip-whatever. Because when I turn the phone of it seems to run more stable. Errors are not gone but at least I can use it as a mp3 player then.
I tried lots of roms but none of them worked fine. I even restored the original spl to make sure it is not the spl. But error is still there... stronger than ever
I will send it back to htc. This thing is obviously broken. Its one of the typical qualcomm errors. These chips are... what do you say in english... moody? My old polaris had a similar error. the 3g part of the phone went away.
TerianSilva said:
I have the same problem. Diamond swiches to standby mode and does not resume or just the light switches on and the screen is blank. Sometimes, it even switches off while booting. All the time, I have to remove the battery. And after some "battery remove resets", the error seems to occur more and more often. It also suddenly looses the phone signal but immediately finds a new one ofter 1-2 seconds.
I think it is somehow related to the phone chip-whatever. Because when I turn the phone of it seems to run more stable. Errors are not gone but at least I can use it as a mp3 player then.
I tried lots of roms but none of them worked fine. I even restored the original spl to make sure it is not the spl. But error is still there... stronger than ever
I will send it back to htc. This thing is obviously broken. Its one of the typical qualcomm errors. These chips are... what do you say in english... moody? My old polaris had a similar error. the 3g part of the phone went away.
Click to expand...
Click to collapse
Sounds bad
I'm trying an updated radio rom at the moment, we'll see if it hangs today...
mikkelnl said:
Hi all,
My Diamond is acting weird lately; sometimes (so far it seems at random) when I turn on the device (from standby), the display is grey'ish / scrambled, and nothing works. I have to removed the battery to get it working again.
This happens with all ROMS found here (haven't tried stock rom yet).
Anyone know what this might cause?
I'm running dev. edition SPL from olinex...
Any tips would be greatly appreciated!
/edit; Could this be SPL related?
Click to expand...
Click to collapse
Hi mikkelnl... from what you described, it seems to be a typical problems with the SPL you are using. Depending on which SPL that the original ROM that came with your device, you can resolve by installing the respective 1.37 OliNex HardSPL Unsigned or the 1.93 OliNex HardSPL Unsigned by cmonex.
Try to get it from the same thread that you got the 1.40 OliNex HardSPL-Developers Edition. There is also some explanation on the problems that you are experiencing.
One more thing, Radio 1.00.25.08 also appears to have some detrimental effects on some devices after some usage. And it has a lingering effects too. Try use Radio 07 if you are in Europe or Radio 05 if you ar in Asia...
Having said all these, I must state that these are purely my observations and you really need to try it out for yourselves to know whether it works for you. I have given the same advice to about 5 users experiencing these problems and it had worked for them so far.
Swiftblade said:
Hi mikkelnl... from what you described, it seems to be a typical problems with the SPL you are using. Depending on which SPL that the original ROM that came with your device, you can resolve by installing the respective 1.37 OliNex HardSPL Unsigned or the 1.93 OliNex HardSPL Unsigned by cmonex.
Try to get it from the same thread that you got the 1.40 OliNex HardSPL-Developers Edition. There is also some explanation on the problems that you are experiencing.
One more thing, Radio 1.00.25.08 also appears to have some detrimental effects on some devices after some usage. And it has a lingering effects too. Try use Radio 07 if you are in Europe or Radio 05 if you ar in Asia...
Having said all these, I must state that these are purely my observations and you really need to try it out for yourselves to know whether it works for you. I have given the same advice to about 5 users experiencing these problems and it had worked for them so far.
Click to expand...
Click to collapse
Hi Swiftblade!
Thanks for the reply. I've read about those newer SPL versions, but I didn't think it was the reason for my problems, since I have one of the first Diamonds (can't remember the spl version ). And; the thread mentions "fuzziness issues on some newer diamonds", my screen is not 'fuzzy', it simply is scrambled and the device completely hangs. So I didn't figure that would be the problem
Anyways; I am a bit reluctant to install a new SPL, never did that before...
mikkelnl said:
Hi Swiftblade!
Thanks for the reply. I've read about those newer SPL versions, but I didn't think it was the reason for my problems, since I have one of the first Diamonds (can't remember the spl version ). And; the thread mentions "fuzziness issues on some newer diamonds", my screen is not 'fuzzy', it simply is scrambled and the device completely hangs. So I didn't figure that would be the problem
Anyways; I am a bit reluctant to install a new SPL, never did that before...
Click to expand...
Click to collapse
Hi mikkelnl.. It's really worth a try. the description on the thread is of course vague. It is actually to deal with some discrepancy issues between SPL and the device's specification.
Doing a HardSPL will not affect your rom but it will hard reset it so you get a fresh clean rom. Do perform a backup before you do a HardSPL though. My best bet is 1.37 OliNex HardSPL Unsigned.. Cheerz
Edited: If this HardSPLs can't solve your problems then it might be a hardware issue that you are facing...
Well, I just installed 1.37 olinex, let's see if this helps
Thanks for the input Swiftblade! Now I'll just have to re-setup your 7.0 rom
mikkelnl said:
Well, I just installed 1.37 olinex, let's see if this helps
Thanks for the input Swiftblade! Now I'll just have to re-setup your 7.0 rom
Click to expand...
Click to collapse
Hope it works out for you bro... Good Luck!
My ATT 8525 is running
ROM version 2.15.502.3
ROM Date 04/09/07
Radio version 1.40.30.00
protocal version 32.73.7020.16H
I've been having problems with my screen fading out to white, physical send and recieve buttons not always working, and alarms that restart after every on/off cycle of my phone. Despite unchecking all the alarm boxes. I've done soft resets, to no avail. Have not done a hard reset yet.
I downloaded the WM 6 file from the ATT site back when it was available, but never installed it.
My question, Is this SW or HW trouble and might an upgrade to WM 6 fix these problems? I'm trying to keep this unit running until I can get hold of the Touch Pro 2, or whatever ATT is going to call it.
hmm.. normally a default rom would fix most software issues.. its unsure if your problem is due to hardware issues..
from my point of view.. it seems like a hardware issue.
flash out the AT&T striped without the radio and try it out.. if its software issues.. most probably its gonna be fixed.
well if it doesnt fix.. tat should mean a hardware issue.
jus keep flashing rom until u find the right one.
Thanks for the reply
hi i was using 5.0 with my new D900 then i read on forum update windows to 6 then i download it and double click on it phone just not working on showing
USB on bottom v2.01 nothing els phone not working anymore
then i also use
mtty1.42
then
task 28 55aa
all command everything work fine but i dont know what to do next after running phone still showing same thing please help im a NOB i know
Welcome to forums
I asume you already read the Wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Have you tried doing DOC format?
Good luck,
chamkilla said:
hi i was using 5.0 with my new D900 then i read on forum update windows to 6 then i download it and double click on it phone just not working on showing
USB on bottom v2.01 nothing els phone not working anymore
then i also use
mtty1.42
then
task 28 55aa
all command everything work fine but i dont know what to do next after running phone still showing same thing please help im a NOB i know
Click to expand...
Click to collapse
So, you flashed the ROM and the device didn't switch on? Then you used mtty and everything went well, but now you don't know what to do? Try another ROM for your device. If your phone has USB at the top and bootloader version numbers at the bottom - you are in bootloader mode, ready to flash.
Tml_wm61_21028_regular_64mb
hi
i install TML_WM61_21028_REGULAR_64MB and i got problem my phone work for few hours and then it dead for few hours nothing no button nothing showing just dead no light
then i take out battery and put again after few hour it work again for few hour and then dead again is that battery or ROm problem please help
also please tell me somthing about RADIO i got 0.0.0 verion in phone what is the use of Radio
please explain little
Perhaps your battery has to be changed
Radio improves signal and also afects on battery, for Tomal ROM´s the most recommended are:
1.18
1.17
1.15
You can find them in the Wiki or in the fttp, or using search button
chamkilla said:
hi
i install TML_WM61_21028_REGULAR_64MB and i got problem my phone work for few hours and then it dead for few hours nothing no button nothing showing just dead no light
then i take out battery and put again after few hour it work again for few hour and then dead again is that battery or ROm problem please help
also please tell me somthing about RADIO i got 0.0.0 verion in phone what is the use of Radio
please explain little
Click to expand...
Click to collapse
Radio is your GSM carrier signal picker and cannot be 0.0.0. Different Radio versions allow you to pick up signal better or worse, depending on many factors, such as tower proximity, location, obstructions etc. Higher Radio version number does not necessarily mean better, but in many cases there can be an improvement in reception. Different ROMs work better with particular Radio versions and the ROM creator will generally recommend the Radio to use with his ROM, based on testing. Sometimes you may find other version works better for you than others.
I suggest for you to try and flash your original ROM, the one that was on your device out of the box. The original ROM package comes with everything you need in 3 parts - OS, Radio and ext ROM. Once you have all 3 established and your device working properly, you can eliminate your device as being the culprit, which leaves a battery.
The problem you described might sound like a battery problem, not sure whether you described your Radio problem correctly, but if that's the case you can try flashing Radio only and see if it solves the problem. Although without any Radio (and custom ROMs come without Radio), I don't see how you could use your device as a phone at all.
hi
hi thanks for your reply can anyone give me original ROM for XdaExec O2
waiting for ur reply please help
Nex time please use the search button
http://forum.xda-developers.com/showthread.php?t=539252
hi
hi i have installed 64mb TOMAL and 1.18 radio
but i have one strange problem the the button just going down down down automatic even i dont touch anything it scroll down automatic
is anyone know why its happening ?
Please post your questions regarding an specific ROM in the proper thread on Universal mobile 6
chamkilla said:
hi i have installed 64mb TOMAL and 1.18 radio
but i have one strange problem the the button just going down down down automatic even i dont touch anything it scroll down automatic
is anyone know why its happening ?
Click to expand...
Click to collapse
My guess is your button is jammed or PCB is damaged as the worst case scenario.