Related
I have a HTC touch with Bell. I flashed NFSFAN's WM6.5 onto it. I didn't use a cab, mostly because I couldn't figure out which one or how to....
When I power on my phone I get to the today screen and I can't do a thing. It shows the correct time, and flashed the green light... I can see the options, and if I press on the screen the phone vibrates.
What did I miss? Oh ya, and how do I turn off the vibrate on screen press when I do get this working?
Thanks!!
On subsequent restarts I find that I am sometimes unable to even get to the today screen and connecting to the PC is impossible.
Hope that helps explain it.
The question is, what did you flash it WITH!?
NFSFAN's 6.5 21198 V3 GENERIC CARRIER ROM
x01001010x said:
NFSFAN's 6.5 21198 V3 GENERIC CARRIER ROM
Click to expand...
Click to collapse
did you update the radio first?
did you hard reset after you flashed?
did you flash this ROM via activesync or bootloader mode?
Detroit Doug
Yes I think I did update the Radio. I used the current bell version from HTC. (Radio Version 3.42.50)
Yes I have hard reset the phone. I noticed that it froze once after a hard reset and had replaced the start with customization. I left it for 10 minutes but nothing had changed so I reset it.
I entered bootloader on my phone, plugged in the usb cable then ran the loader on the pc and waited for that to complete.
x01001010x said:
Yes I think I did update the Radio. I used the current bell version from HTC. (Radio Version 3.42.50)
Yes I have hard reset the phone. I noticed that it froze once after a hard reset and had replaced the start with customization. I left it for 10 minutes but nothing had changed so I reset it.
I entered bootloader on my phone, plugged in the usb cable then ran the loader on the pc and waited for that to complete.
Click to expand...
Click to collapse
OK, there is an issue with the flash from what it sounds and bootloader is done from the SD card NOT from a USB cable, try this...
- Using the original SD Card that came with the phone (or any SD card under 2GB in size) Format your SD card making sure it FAT32
- Copy the RUU_signed.nbh file over to the that card and rename it VOGUIMG.nbh
- Then flash via bootloader power+camera+stylus, it will pull the image to flash from your SD card automatically
- wait and then hard reset (red+green+stylus) after customizations/autotun occurs
then try using the phone, hopefully that will take care of the issue
Detroit Doug
Detroit_Doug said:
OK, there is an issue with the flash from what it sounds and bootloader is done from the SD card NOT from a USB cable, try this...
- Using the original SD Card that came with the phone (or any SD card under 2GB in size) Format your SD card making sure it FAT32
- Copy the RUU_signed.nbh file over to the that card and rename it VOGUIMG.nbh
- Then flash via bootloader power+camera+stylus, it will pull the image to flash from your SD card automatically
- wait and then hard reset (red+green+stylus) after customizations/autotun occurs
then try using the phone, hopefully that will take care of the issue
Detroit Doug
Click to expand...
Click to collapse
Shouldn't be an issue flashing from bootloader mode via PC cable. Bootloader allows the computer to reckonize your phone as a usb device.
The 6.5. ROM is still a custom ROM, so the question is have you unlocked your phone?
If not unlock using imcokeman's 2.31 unlocker first, then follow dd's instructions.
jmitr said:
Shouldn't be an issue flashing from bootloader mode via PC cable. Bootloader allows the computer to reckonize your phone as a usb device.
The 6.5. ROM is still a custom ROM, so the question is have you unlocked your phone?
If not unlock using imcokeman's 2.31 unlocker first, then follow dd's instructions.
Click to expand...
Click to collapse
Yeah the "I think " part got to me as well until I remember responding to a different thread of his helping him along in getting started to flash and in that one he had unlocked as was on his 3rd ROM by the end of it LOL so I believe he has successfully unlocked his phone, just the issue may be corruption in the flash of the 6.5 WinMO ROM
Detroit Doug
Ok. I will have to find my smaller card. All I have here is a 4GB one.
Thanks jmitr and Detroit Doug! I will try moving the file to the card. It will take me a few days to get my smaller card as I left it at the office.
Any luck yet? let us know how it worked out for you...
Detroit Doug
I will. I turned my office upsidedown looking for that little card... and it was at home by my laptop the whole time.
I have it now, and actually just came online to get the file names I need. I will keep you updated.
Well... that was a little different. I didn't get the customization the first run after the flash. I did however get it immediately after the hard reset.
So far (and about 10 min.) everything is looking good!
I will play with it for a while and let you know.
Thanks for the help!!
x01001010x said:
Well... that was a little different. I didn't get the customization the first run after the flash. I did however get it immediately after the hard reset.
So far (and about 10 min.) everything is looking good!
I will play with it for a while and let you know.
Thanks for the help!!
Click to expand...
Click to collapse
No problem and welcome to the wonderful world of hard drug.... ummm I mean flashing, yeah flashing thats it
now that your hooked you can forget about sleep, family, a life, anything else
MUH HA HA HA HA ha hahhahahahahahahahahhaha
Detroit Doug
Oh ya! That looks like it did the trick.
It has been running since my last post without locking up... the internet works... and it is slick!
Thanks for your help Detroit_Doug and jmitr! I appreciate it.
i have flashed my diamond with the official htc rom
im on 1.40 olinex, now i can only access boot mode.
sometimes if i leave the phone without a battery for like 2 hours, when i turn it on i see the "touch diamond" logo, if i leave the battery for a whole day i see the windows mobile loading screen, but then suddenly the phone turns off
plz if you have any idea about this problem help me
If you can acces bootloader, then your diamond isn't bricked.
Try the unsigned version of olinex' hard-SPL and flash the ROM again.
Good luck!
hey ElCondor, im on 1.40 olinex, i cant flash it because it is protected
how can i flash the unsigned 1.40 olinex one?
Here is a link to the unsigned hard-spl.
Make sure you download "Unsigned-Hard-SPL-Diamond-OliNex.zip".
Follow the instructions:
1) Download, extract to an empty folder.
2) Run RomUpdateUtility.exe, Have Phone Synced with PC (go into bootloader, connect your cable, then the word "serial" in bootloader will change into "USB".
3) follow steps, check device for prompts after PC shows loading bar. it should go to black screen now.
4) SPL flashes, device automatically reboots, job done.
5) to confirm you got it installed, go into bootloader mode (volume down + reset, i.e. press volume down button and reset then keep holding the volume down key until you see tricolour screen) and verify the screen shows 1.40.OliNex.
note: you will not see the SPL version during normal boot, that is the OS version, not SPL!
Installing this will hard-reset your device.
Best Regards,
ElCondor
when i flashed the unsigned 1.40 olinex, the device rebooted
windows mobile is preparing your phone for first use
htc logo
phone went off :S
will try flashing rom again
flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?
mzaouar said:
flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?
Click to expand...
Click to collapse
Hi
If you can access the bootloader then your device is not bricked. Therefore download a rom of your choice then connect to the usb when on the bootloader then use a Diamond custom RUU (normally come with the rom) follow the steps. After rom updated make a hard reset. I hope it will run ok.
Looks your symtons are showing like your rom corrupted.
Good luck
i am flashing this ROM
RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
the newest one i downloaded from htc. com is giving me rom update error
would you recommend a good rom for my phone?
after flashing and reflashing and hard resetting with the ROM showed above
still cant boot in ROM mode, only in boot mode
el condor sabes, anything ???
should i flash with a new rom, and if yes with which?
(diam100 olinex 1.40 unsigned)
Perhaps try a custom rom?
I found when flashing to an official rom from a different provider (my phones telstra and was flashing 3) I had issues with the rom booting and had to follow a post on here somewhere to get it working, however When I had this problem I could still flash any custom rom with no issues.
Unless its for warrenty purposes then its probably not worth flashing the "original" perhaps flash A.Z.T.O.R. = Alpha Zero Tweaked Official Roms which are close to the original but with benifits of being modded for faster speed etc.
Anyways Im no pro but I know what you are going through and I am trying to find the link to the fix to your problem as I also had the problem. But recommend trying a custom rom to confirm the problem is the same as mine.
For the record now I do not use official roms anymore, with WM6.5 running well for the most part on the diamond its a great step backwards when you revisited 6.1
flashed to SwiftBL-WWE-Diamond-v7.5-Full-16MbPP
still same problem can only go to boot mode
i am feeling there is no solution to my problem ?
is the phone bricked? :S
If you haven't done yet, flash the hard-spl I posted. Just do it, re-instal the hard-spl! Then, flash another ROM, maybe (as said before) your rom is corrupted.
The problem here is, that you first installed the unsigned hard-spl, and then flashed a corrupt rom. In that way, the hard-spl can be damaged too, so flash the hard-spl again and flash another rom should work.
Good luck!
I did :S but to no avail, I will do it again fingers crossed :S !
update: weird, everytime after i flash the hardspl unsigned, it boots up, i can see the "touch diamond" logo
windows mobile booted.. preparing your device..
update 2: windows mobile booted, installing everything
omgomg it looks it might work this time, fingers still crossed !!
el condor !! haha fingers crossed
update 3 :S : windows mobile installed properly, phone rebooted, went again and opened it, then i heard a sound from the speaker and the phone turned off :S
it must work what could the problem be now? last step !
Okay try a hard-reset, maybe that works.
If not, then flash hard-spl again, then hard-reset, then flash another ROM. Then hard reset. Then try again if it boots.
Is your battery enough charged? That could also be a reason.
did not work, wont even boot up
when i said if i leave battery out and such, I thought it might be hardware/heat related
http://www.htcwiki.com/thread/2069847/HTC+Diamond+-+Severe+Crashing+Problem,+maybe+heat+related
could this be it? will i have to send my phone for repairs?
because maybe when WinMo was loaded, the phone started to heat up and it shut down
so basically my solution is not a software fix??
If none of the tips worked, and you have the same problems as described in the site you linked, then you probably have to send it back.
One thing you could do: Try if the other hard-spls (1.37 and 1.93 unsigned) are working for you.
I'm sorry for you, maybe someone more skilled than me (like cmonex or olipro) knows how to solve your problem.
it's alright :S i thank you for all the help you have offered !
( it is customizing right now) but i expect it to reboot anytime now
worked, 5 minutes into winmo it restarts
mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....
mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
OK good to hear that, if you have any more questions in future, just ask!
Glad to be of some help
msvb007 said:
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....
Click to expand...
Click to collapse
Ive sent you a pm, there's no need to use this thread for your questions because the problem in this thread is solved.
So take a look at your pm!
Hello,
I am using a Sprint TP2 and just tried changing my ROM from Stock to Energy Leo ROM.
I installed the Hard SPL Unlocker and it seemed to work fine. I then went to flash the new ROM and it seemed to load fine, but upon restarting, it locked on the "Touch Pro2" startup screen.
I am thinking that I probably installed the GSM version of the new ROM, so I will need to install the CDMA version.
I am able to get to the bootloader screen and when I go to directly change the ROM from the GSM version to the CDMA version, the RUU seems to be working, appears to be able to access my phone, and starts the install.
My phone switches to the progress bar screen BUT both my PC and my phone stay at 0% until my PC displays an error message (#262).
What do I do to either re-install the Sprint Stock ROM or get my phone to change to the CDMA version of the ROM??
HELP!!!!
Thanks so much.
Why can't you get the device into bootloader mode?
I read a post about someone else that did the same thing, flash gsm rom to cdma device, and he put his device into bootloader and flashed the cdma rom and everything was back to normal.
I have to try a couple times to get to bootloader mode because its hard to hold down the power button, vol down and press the stylus reset, sometimes i get a friend to help and works out fine.
I'm able to get the device into Bootloader mode but it doesn't do anything when I use the RUU (my phone is attached to my PC via usb), it stays at 0% and then comes up with an error. I'm going to try to see if I can load the new ROM from my micro SD card.... let's hope it works...
UPDATE:
I put the new ROM nbh file onto my micro sd card and put it into my phone and entered bootloader, it flashed a quick screen that said "Loading" and then "No image file found!" and then returned to the bootloader screen. What can I do???
More info:
My bootloader screen reads:
RHOD400 32M SS_BC
SPL-0.63.0000
MicroP(LED) 0x0A
MicroP(Key) 0x04
TURBO HW/TURBO SW
TP MFG DATA
468,512 751,806
768,180 206,210
194,825 Calibrated
Hello, just wondering if anyone was able to help me. This thread has had many views but no suggestions. Anything is GREATLY APPRECIATED!!
Thank so much!
When you flashed via microSD, did you name the ROM file rhodimg.nbh? It has to be named rhodimg.nbh in order to be detected by the SPL.
Yes, I did make sure that the file was titled that. I'm beginning to think that my phone isn't correctly unlocked, so if that's the case, is there any way of applying Hard-SPL via a Micro SD card?
Did the same mistake, and was also having problems to fix, in my case what was wrong was the card was formated FAT instead of FAT32, after reformat/recopied the CORRECT version of LEO and renamed to RHODIMG.nbh/ Volume Down + Power it worked perfectly!
Hope it helps!
SO CLOSE!! I re-formatted my Micro SD card to FAT-32 and re-inserted the card and loaded my phone into Bootloader and it stayed on the white "Loading" screen with blue letters!!!! GRR!!!! Any ideas? Where can I find a ".nbh" file for the Hard-SPL? Maybe I didn't unlock it correctly??
andrewkariana said:
Yes, I did make sure that the file was titled that. I'm beginning to think that my phone isn't correctly unlocked, so if that's the case, is there any way of applying Hard-SPL via a Micro SD card?
Click to expand...
Click to collapse
Yeah, looking at your bootloader readout that you posted in the third post, I now see that you don't appear to have HardSPL on your device. As far as I know, there's no way to apply HardSPL without being able to boot into Windows Mobile, since HardSPL needs a SSPL to flash it. It seems you should flash back the stock ROM, but unfortunately the stock ROM doesn't seem to exist as an official, signed download. I'm not sure what else you can do to unlock with HardSPL, other than wait for the Sprint 6.5 ROM update (expected by end of Q1 2010).
DaveTheTytnIIGuy said:
Yeah, looking at your bootloader readout that you posted in the third post, I now see that you don't appear to have HardSPL on your device. As far as I know, there's no way to apply HardSPL without being able to boot into Windows Mobile, since HardSPL needs a SSPL to flash it. It seems you should flash back the stock ROM, but unfortunately the stock ROM doesn't seem to exist as an official, signed download. I'm not sure what else you can do to unlock with HardSPL, other than wait for the Sprint 6.5 ROM update (expected by end of Q1 2010).
Click to expand...
Click to collapse
So am I not able to use the stock ROM that I found from a thread (on an outside forum :-/ )??
ISSUE RESOLVED!!!! Thank you, everyone!! This is such an amazing forum!!!! (I ended up just loading the stock rom file that I found. DUH! So much easier than I thought it was going to be)
andrewkariana said:
So am I not able to use the stock ROM that I found from a thread (on an outside forum :-/ )??
Click to expand...
Click to collapse
If it says something like "rebuilt", "reconstructed", or anything that indicates that it was dumped off the phone and rebuilt, then no. See, you need a signed ROM, and dumping a stock ROM off a device and rebuilding it breaks the signature on the ROM, so a stock SPL won't flash it.
vol dn pwr on
all you have to do is hold volume dwn then power on.
fone_fanatic said:
Why can't you get the device into bootloader mode?
I read a post about someone else that did the same thing, flash gsm rom to cdma device, and he put his device into bootloader and flashed the cdma rom and everything was back to normal.
I have to try a couple times to get to bootloader mode because its hard to hold down the power button, vol down and press the stylus reset, sometimes i get a friend to help and works out fine.
Click to expand...
Click to collapse
Same Mistake..
Thank you guys for all your help, I also flashed a GSM rom to my CDMA phone I was scared I had bricked it.. Nobie here but it worked like a charm
Hi everyone well I'm new to the flashing and dont want to jump any steps as this could possible brick my phone...
I've been having some problems with flashing as i cant find a step by step to flashing my HTC TP2. I've managed to do the RhodiumW Hard-SPL package but after trying to flash to some custom RUU's the installation seems to go fine its not until the phone first boots up, that's when the phone just hangs on the HTC splash screen
From there i cant do anything other then boot up to the tricolor bootloader screen and re-install the original 2.04.651.4 update!
can someone tell me what im missing to be able to flash my HTC correctly, or at least point me in the right direction?
Thank you in advance!!!
step 1
http://member.america.htc.com/download/RomCode/HTC Touch Pro2 (Sprint)/HTC Touch PRO2 MR1.exe
step 2
http://rhodiumw.htc-unlocks.com/hard-spl.php
step 3
http://www.mightyrom.com/mightyrom/touch-pro-2/
Hey Tommy many thanks for the post. I just upgraded my phone and peeling through the information overload, however you direct link does not work for step 1. I want to make sure that I am running the correct piece of software that you recommending. Could you please list the title for that file?
Nevermind I was able to find it via a mirror site.
Back into lurker status for now
Thanks
alright so i was able to install they mightyrom on my phone that went well my phone didnt freeze and everything started the way it should have.
but does that mean i can now flash my phone to other for example "leo cell" or Bxsteez Rhodium" if not how do i get to that point cuz when ever i flas them to they just freese on the white splash screen with the HTC logo in green letters!!
Thanks!
If you have installed Hard SPL then use the sd card method.
1. Format the sd card FAT32 ( they come FAT default) and copy the rom's .nbh file onto it. Rename to Rhodimg.nbh .
2. Insert sd card back into powered off Rhodium. Go into bootloader by pushing down volume and power.
3. If you did it properly and Hard SPL is on your phone then it should say to press power to update os...
If you aren't sure if you have Hard SPL then go to bootloader without the sd card in there, it should say SPL - 0.85.Olinex if you have Hard SPL, anything else won't register the flash file.
Cheers...
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
"the device needs to be connected to Activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. the phone part should be on).
3) internet access is required as the program checks online for updates and for the license."
Click to expand...
Click to collapse
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
signalsoldier said:
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
Click to expand...
Click to collapse
I think you should ask this in the hard spl thread in the cmda section...That is the place for those questions Assuming that you have a cdma phone because you did not mention it. Otherwise check the hard spl thread in the gsm section.
Heading that way thanks for the directions mate!
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
htcru7 said:
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
Click to expand...
Click to collapse
Just flash away
LOL alright thanks i guess im just paranoid but thanks i'll "flash away"
Lock
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Scream-krg said:
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Click to expand...
Click to collapse
the Hard-SPL will only work if you booted windows mobile. you have to sync the phone in windows mobile to the PC.
is there other way to get through in hard spl because i dont have any account for example, paypal...... http://media.xda-developers.com/images/icons/icon9.gif
chrisjavier666 said:
is there other way to get through in hard spl because i dont have any account for example, paypal......
Click to expand...
Click to collapse
Hard SPL is free for non-commercial users.
my tp2 is bricked
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
nastyrock said:
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
Click to expand...
Click to collapse
Did you try flashing the stock ROM? It's always a good idea to try that if you think there's no hope. It flashes everything.
Also, did you try task29?
well last night my phone was working fine i have a t-mobile TP2 , phone died , i put it on charger till it was fully charged and turned it on and it doesnt go past boot screen.
i tried fixing it several ways
1. went into bootloader mode and tried to reflash a newer energy rom, finished that and reset the phone and still samething.
2.went into bootloader again and tried to reflash a stock tmobile rom and once again didnt work.
3.flashed a different radio and still stuck
4.tried 1&2 via micro sd and still samething
any ideas ? on what should i do or is my phone done ?
thanks.
Flash the stock ROM. If it still doesn't work, then try doing a Task29 (search for that in the TP2 ROM Development forum), a radio re-flash, and a ROM re-flash. If that doesn't work, then it's a brick.
sumflipnol said:
Flash the stock ROM. If it still doesn't work, then try doing a Task29 (search for that in the TP2 ROM Development forum), a radio re-flash, and a ROM re-flash. If that doesn't work, then it's a brick.
Click to expand...
Click to collapse
Good advice here, but if this doesn't work and you need to send it back, make sure to put the stock SPL back on it. Grab that from the Hard SPL thread.
I read something about plugging in your headset and then it will boot (go past the bootloader) If that is the case, your usb port is broken.
sumflipnol said:
Flash the stock ROM. If it still doesn't work, then try doing a Task29 (search for that in the TP2 ROM Development forum), a radio re-flash, and a ROM re-flash. If that doesn't work, then it's a brick.
Click to expand...
Click to collapse
thanks for the advice but didn't work for me , i cant do anything because the Rom loader stays on 0% and when i try to do it via micro sd it stays on loading the rhodimg , doesn't go past loading
cajunflavoredbob said:
Good advice here, but if this doesn't work and you need to send it back, make sure to put the stock SPL back on it. Grab that from the Hard SPL thread.
Click to expand...
Click to collapse
Good idea , i have stock spl on it now, but the radio isnt stock i tried flashing stock radio but no progress, stays at 0% now
sumflipnol said:
Flash the stock ROM. If it still doesn't work, then try doing a Task29 (search for that in the TP2 ROM Development forum), a radio re-flash, and a ROM re-flash. If that doesn't work, then it's a brick.
Click to expand...
Click to collapse
and to do a task29 doesnt the phone need to be connected to computer via active sync? well since my phone wont go past boot screen cant do that , idk what else to do..
enanito89 said:
and to do a task29 doesnt the phone need to be connected to computer via active sync? well since my phone wont go past boot screen cant do that , idk what else to do..
Click to expand...
Click to collapse
You don't need a USB connection to flash anything. You could load the .nbh file onto the root of the SD card. Once in bootloader mode, it will flash straight from the SD card. This works for task29 as well. If you aren't having any luck so far, this might not help, but it is an alternative to USB flashing.
cajunflavoredbob said:
You don't need a USB connection to flash anything. You could load the .nbh file onto the root of the SD card. Once in bootloader mode, it will flash straight from the SD card. This works for task29 as well. If you aren't having any luck so far, this might not help, but it is an alternative to USB flashing.
Click to expand...
Click to collapse
tried the img doesnt load , it stays on loading screen.
enanito89 said:
tried the img doesnt load , it stays on loading screen.
Click to expand...
Click to collapse
If you aren't having any luck, then neither will T-Mobile. If you've got the stock SPL on it, then just do a warranty exchange.
cajunflavoredbob said:
If you aren't having any luck, then neither will T-Mobile. If you've got the stock SPL on it, then just do a warranty exchange.
Click to expand...
Click to collapse
thats my only option left , thanks for the help guys.