hii im new here.. can anybody help me.. when i turn GARMIN. the signal is zero..
i can't connect to the satelite.
im confused.. any1 can help me.??
im using WM6.0 my device version is HE1..
help me plss.. i can;t use my GPS....
Set your GPS Port to COM1, then wait....
sometimes it take me half hour to get a fix.
However, after the first fix, subsequent fixes in the same area will be quite quick.
kaskaika said:
hii im new here.. can anybody help me.. when i turn GARMIN. the signal is zero..
i can't connect to the satelite.
im confused.. any1 can help me.??
im using WM6.0 my device version is HE1..
help me plss.. i can;t use my GPS....
Click to expand...
Click to collapse
Make sure your GPS program port set to COM8, GPS Hardware port: COM9 Baud rate: 4800 & Tick "Manage GPS automatically" under GPS Settings.
You should test your GPS outdoor NOT INDOOR!
Related
Has anyone tried Navigon MN5 with Artemis yet?..........
Thanks
Rafiki
I did.. Navigon works fine, but is really slow on my Artemis. TomTom is much faster. I tried Navigon because of the TMC support, but i can't get TMC to work on my device. I'm going to try iGo 2006 as well, but for now TomTom does the job very well.
Now I'm using iGo 2006. I can recommend this piece of software to everyone, it's much faster than both TomTom and Navigon. The looks are incredible.
My tomtom takes ages to find the sats when you first boot it up. Is this normal??
tmaxx said:
My tomtom takes ages to find the sats when you first boot it up. Is this normal??
Click to expand...
Click to collapse
Try to find the upgrade to v6.02 as this has the option for "Built In GPS" and it'll then use the Quick GPS data. Cold start is now 10 seconds for me with warm start being about 3 second!
Navigon 6
Navigon 6 works fine, but it is really slow on Artemis, is there anyone knows how to turn the first warning off in the begining of screen ?
Does iGo support QuickGPS so that it can lock on fast?
A cool nav program is Route 66. Works fine and gets a fix in approx.10 sec. Uses same maps as Navigon btw!
TomTom is a joke if you live in Eastern Europe. Either no maps at all or very poor with only very major roads.
I only work with DestinAtor on my Artemis. Version 6.0.0.
Very fast fixes (approx 6-9 seconds) and response from map is better then TommyTommy, according to a friend of mine. He switch over to DestinAtor aswell.
TomTom GPS Settings...?
low405 said:
Try to find the upgrade to v6.02 as this has the option for "Built In GPS" and it'll then use the Quick GPS data. Cold start is now 10 seconds for me with warm start being about 3 second!
Click to expand...
Click to collapse
Guys can someone tell me what settings they have on their Artemis' GPS Settings and on their TomTom 6.200?
On my Artemis' GPS settings, I have it set to:
GPS Programs Port: COM4
GPS Hardware Port: COM2
Baud Rate: 4800
Manage GPS automatically set to: ON
And on the TomTom settings I configured it to use the Other NMEA GPS Receiver, set the baud rate to 4800 and then when it asks "GPS is connected to:" I just select COM4 which is the first option.
Now this works for me pretty well but the weird thing is my HTC P3600 seems to be a lot quicker at getting a fix and it has connections with more sattelites and a better signal than the Artemis!
As far as I know, the artemis is suppose to be much better when it comes to GPS because it has the latest Sirf 3 GPS receiver and from what I read somewhere, the P3600 has another GPS chip not as good as the Sirf 3.
Would be good to know what settings everyone else is using. By the way TomTom only seems to detect the GPS when the GPS Programs Port is set to COM4 on the Artemis' GPS settings. Setting this to anything else doesnt work.
Thanks in advance.
D.C
Hello, I put the Navigon 6,2 software on my P3300 today. Awesome stuff. The update 6,2 has improved the Speed alot.
The only thing that i need help with is the TMC service.
how can i get that up and running?
Thanks
Tim
Hi,
I'm currently running navigon 6.1.5 on my P3300 with WM6 (NewArtemis2). Every now and then I'm getting the message that my memory is full. At that moment I can choose to end different programs. Normally or MN6 or phone. Because I'm using navigation I choose telephone. Then after a few minutes I'm getting a network faillure and MN6 ends.
Is this a known problem and if it is, is there a sollution for it?
Thanks for your help.
Paul
Bringing up an old topic again.
I tried to install Navigon MN6.2 on my artemis. Everything goes well, except for the images on the screen, it's far from smooth.
How did other people manage to run MN6.2 to run smoothly on there Artemis?
Hi,
please can someone tell me, why the inter gps only works with TomTom
on my XDA ORBIT?
I tried MioMap from a friend, but it tells me: No GPS was found.
Same problem with other software like gpstuner / smirftech and so on.
What can i do?
Is there a trick?
Are there tools to tweak the gps ?
Please give me an tip.
Big THanks
Bye
On my MDAC3 it works fine with both Tom Tom and Memory Map and it also worked with Pocket Earth.
Regards
TomTom is not the only software that works with the internal GPS - I tried several that worked (for example, ESRI ArcPAD 7.01 and MagicMaps2GO 2).
But you are right, GPSTuner doesn't work - it locks up my device while trying to find the GPS. There is a workaround described in the GPSTuner-Forum: You have to install GPSGate (software that works as an intermediary between the GPS and any other software) (http://gpstuner.com/forum/viewtopic.php?t=1044).
But contrary to what the developers of GPSTuner think (namely, that TomTom locks out every other software from using the internal GPS), I don't think that's right because at least to different applications from different vendors work. There has to be something else...
Ah, big thanks!
Please tell me your config for GPS.
Why you can find the gps intern for MioMap!
I have got the same hardware like you!!
Please
Big big thanks
works ok with igo2006 and papago7 also
the problem is with destinator6 last version 6.1.1.4000
and we waiting for a bugfix from destinator tech.
a trick that can fix this prob is if you put the version with tmc and have always the tmc on,with this the com port stays open
config
com4 baud 115200
tmc on com4 9600
thiw trick was find from user Minotavrs
*sorry for bad english
Please help, i dont understand it???
What can i do for MioMap?
It doesen´t find the gps hardware.
djsven said:
Please help, i dont understand it???
What can i do for MioMap?
It doesen´t find the gps hardware.
Click to expand...
Click to collapse
i explain what i do for destinator 6 last version
i do not know miomap
but my config on alla programs is com4 nmea baud 4800
did you try that?
Ah ok!
You set in windows mobil5 gps Port Com4 an Baut 4800!
Ok.
So will try it.
Put no hope.
WOnt work.
i have a big problem with my artemis...
i updated the B&B 3.7 rom...and tomtom dont take signal from sat...
i updated the touch fluo rom...and tomtom dont take signal
i downgraded to original italian rom...and tomtom dont take signal
so i dont know what is the problem!!
when i bought my artemis tomtom was already installed in the phone (not sda)
so i downloaded the Cab from p2p and used it...it works in every way exept gps signal
i think its a problem of tomtom because with any rom i dont recive any response from sat! on tomtom.it site i cant download any Cab to install on phone..only tomtom home but i already have it on the DVD
anyone can help me or give me an advise?
Can you receive a signal at all? Is it greyed out or nothing?
When configuring GPS Hardware. Select another NMEA wired at 4800baud on COM4.
Shand359 said:
Can you receive a signal at all? Is it greyed out or nothing?
When configuring GPS Hardware. Select another NMEA wired at 4800baud on COM4.
Click to expand...
Click to collapse
I always set mine to 9600 baud - for some reason it works better for me on my t-mobile mda iii
Shand359 said:
Can you receive a signal at all? Is it greyed out or nothing?
When configuring GPS Hardware. Select another NMEA wired at 4800baud on COM4.
Click to expand...
Click to collapse
com 4 is the one i set in gps setting right? "data port" or "hardware port"? because the second one i dont have in tomtom port list
Furbious said:
I always set mine to 9600 baud - for some reason it works better for me on my t-mobile mda iii
Click to expand...
Click to collapse
ok...i have some signal now thx very much ^^ i feel like a stupid
when u set at 9600 baud...u modified the one in gps setting too?
Hope someone can help ... I know this should be easy but just can't get things working. I have loaded iGuidance software into my P3300 with WM6 ROM. I dont know what com port to use and which baud rate to set at in iGuidance. In the WM6 "external" software should i check off or uncheck let Wm manage. In this program it wants to know what GPS program port I am using ? and GPS Hardware port and Baud .. Hope someone can help - been about a week and I cant seem to figure it out - thanks very much
I run Destinator for satnav, and have the gps settings at COM4 and 4800 baud in Destinator.
In external GPS, I have the following settings.
Programs tab:COM4
Hardware Tab: GPS Hardware port NONE , Baudrate 4800
Access Tab: Manage GPS ticked.
Also,
I found that sometimes Destinator would say that it had lost the gps connection , then found it, over and over.
To get over this problem, I installed GPSGATE (Google for it).
Run that, it'll find the GPS on COM4, then set a "virtual" GPS connection for COM5.
Try pointing iGuidance to COM5.
That should help.
All of a sudden, when I open Tom Tom, it won't turn on the GPS anymore. I tested the GPS with other applications and it comes on with them, just not Tom Tom. Anyone know what could be wrong?
What com port are you using?
Try to set it to port 4 @ 9600 baut. Or reinstall TomTom
mfg sool
As well as checking the correct com port/gps device make sure Flight Mode is turned off.
soololi said:
What com port are you using?
Try to set it to port 4 @ 9600 baut. Or reinstall TomTom
mfg sool
Click to expand...
Click to collapse
Thanx. I did and now it's working agian.