Develop Bugs

FLASH disaster

I was becoming an expert in flashing...but the cable became undone during a flash :-(
Now it restarts to a blank screen with R1.50.08.11 / G32.83.7020 etc. but goes no further.
Computer no longer sees device.
Used hard keys to go into bootlocker. (IPL 0.50 / SPL- 1.07.000)
My VISTA :-( computer sees device.
Then try RUU, but this gives a 270 error.
Tried moving to XP, but the computer does not install the software for the USB port, so now the RUU gives 200 error. Arrgh.
Question: How to update from a very corrupted ROM? Or where can I find the drivers for the USB port, for XP. and if I do can I do the update from the hard bootlocker?
Any help really appreciated!
MS

Update
Found USB drivers for Windows XP
But getting identical problem as with Vista :-(
Device not seen unless in bootlocker mode.
RUU starts and after 1% quits with 270 error - image file corrupt.
Tried RUU a hard SPL (olipro) but same 270 error occured.
Help still needed...
MS

I think you have to flash original HTC rom prio to try other roms

i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.

sailer1983 said:
i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.
Click to expand...
Click to collapse
Maybe helps:
http://trinityguides.info/index.php?option=com_content&task=view&id=20&Itemid=66

The trinity upgrade guide does not help here.
I can connect to device I have sorted out all the VISTA and XP issues.
The problem is at 1% status the 270 error occurs.
The telephone is actuall a Swisscom 1510. Original ROM was lost in first flashing, have searched but not found official update.
Is there a mini-ROM or a windows WM5 lite ROM which may overwrite what happens while still using the hard bootloader?
MS

Use SD card method.
See wiki page.
Bye

Hi,
...or .... MTTY Procedure....
BYE, Bobo

Tried SD card method - nothing happens. Just sits in Bootloader :-(

Try this procedure
In windows Vista use the attached driver in order to recognize your Device.
If your device is already recognized from windows vista replace the drivers with the drivers in the zip drive.
You have to use the drivers in the attached file not the windows default drivers VERY IMPORTANT!!!
After your Windows vista recognized your device try to flash it
Cheers

Thanks for all the help....but still I am having no success.
The HTC trinity is recognised in both Vista and XP when I use bootloader. (ie HTC USB SYNCH in device manager. Without boot loader the device is more or less dead.
I tried the SD crard trick - nothing happens.
Tried mtty.exe - just get cannot open USB port (on both VISTA and XP).
Nevertheless, the bootloader sees the USB port and the RUU goes to 1% then stops so some communication is happening.
Any other ideas?
MS

The final and, j' m sure, the definitive solution:
Try this one http://forum.xda-developers.com/showthread.php?t=308691&highlight=stack+in+bootloader

Just before I try splxploit, as a note I got this out of mtty
Cmd>info 8
Block 0x0(0) is Reversed block
...
Block 0xC(12) is Reversed block
Block 0x335(821) is BAD block !!!
Seems my problem must be here. Is there another fix besides splxploit?
MS

Install Olipro hardspl 1.20.
Bye

Dear, carefully look that thread again. Stack overflow for Trinity.
It's all my advise. I think you don't do right "Stack method" to get out your problem.
Best regard.(rest calm and do it again).

Uhm, try to download some rom again? and try Rom NVID (no vendor ID) for example. ???

Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS

ManStan said:
Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS
Click to expand...
Click to collapse
So you haven't yet tried splxploit?

END of STORY
YESSS!
POF you are a genius - Splxpoilt worked a dream.
Had to run unbrick.bat once. Hit soft reset, and run again as explained in the readme.
This got a good SPL on the machine - then a standard RUU worked a dream.
At the same time I got the SD card update working too...
OK, OK, so I should have tried splxpoit earlier. But I think I had to do the rest first to understand what was going on.
Strange thing is if I look at my machine again under mtty, there is still the Bad block (821). Who cares, I am unbricked!!!
By the way, this board is just completely amazing.
THANKS TO ALL....

i have the same problem
could you help me . how did you repair your spv?

Can't exit bootloader screen

Hi,
I tried to upgrade my XDA using Ranju's latest updater, the whole process failed and now I'm stuck at the BL screen "USB" at the top (when connected, otherwise it says "serial") and "v1.00" at the bottom.
My PC, SyncCentre and Windows Mobile Device Centre (I'm using Vista) all show the device as being disconnected (up until trying to upgrade everything had been fine).
As it's not showing up on my PC all of the software options for recovering it dont fail, all end with a plethora of USB not connected errors etc
I've tried the how-to on the wiki: http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial to no avail.
Does anybody have any ideas? Greatly appreciated,
Thanks,
Lee

with jasjar-bl1.01-ruu-v1.2 I always restart my JJ Leave your uni in bl and start the application Good luck......
I think the Vista is not the problem this upgrade don't use AS or "in italian centro gestione dispositivi WM"
Bye
M.C.

Well, I flashed my Qtek a while ago, it failed to flash (using Vista) and doing a hard reset after it whas hanging at the startupscreen(the one with all the rom/radio numbers). No matter what I tried, following the instructions on Vista windows mobile center all failed... The good news is that your computer and your PDA still see when it is connected, ie USB/Serial, like in my case!
I then tried it on my desktop/XP, it flashed without a problem...
The funny bit is that I flashed my herald (WM6) 2 times using Vista without any problem...
I cannot explain but if U have the possibility, try and see if it works on XP...!
Good luck!

are you trying to flash it WITH your SIM card and / or SD card inside? If so, try taking them both out! It worked for me a few times!

I would start by getting rid of vista !

i had the same xprience
the different was i downgrade from wm6 to wm5 (i need the vcall)
failed in vista, succeed in xp
-> my advice : try in xp !! don't forget to remove the sd card

Manual for how to flash a rom in Vista
Read this post, you have the solution to the problem here:
http://forum.xda-developers.com/showthread.php?t=313001
You need to update the driver manually, if not, will not be able to install the driver.
You need to do this without sd/sdhc and without the sim.
If you follow these instructions, you can flash with success.
Greetings.
Kali.

Errors Numbers : 266 & 264 & 302 while Upgrading PPC

I decided to tell something about my experience today about these Error numbers while Upgrading my Hermes (T-Mobile MDA VARIO II) .
Dear friends….i read Upgrading instuguidances again and again but there is a gold issue I did not notice untill today.
whenever I put my PPC into Boot Loader Mode and connect it to PC to upgrading these Errors appear immediately and I was in trouble what those errors are.
It checked the cable or some different Official ROMs but in fact I noticed all growth from Windows.
Yeah…
I am in winder why Microsoft does not make it possible upgrading PPC over Windows XPSP3 !!!
Whenever I run RUUWarpper on Windows XP Service Pack 3 these errors shown while I was sure about correct cable and correct ROM and ….
Sooo I want to share it to all peoples this gold notice :
Upgrading PPC is just possible on Windows XP Service Pack 2.
not Windows XPSP3 nor Windows Vista.
I think it is good for someone else that search and find these Topic in database of this nice/great Forum if same problem has appeared to him.
Here is some pictures of those errors & some proof if is required.

Mate, there has been a heap of threads on how to upgrade with Vista. It Works.
I have, on occasion, upgraded my Hermes on Win XP SP3 successfully. If it doesn't work for you, try the sd card method, you have to install Hard SPL V7 first, I tend to use this method more as it seems safer to me... Especially for the radio rom.
All you need to do is search and you should find the answers you seek...
Cheers...

So really can you Upgrade your Hermes on Win XP SP3 successfully?
you mentioned some keywords but could you please show me those links exactly how to upgrade our Hermes on XP SP3 too?
I think this forum is so noisy i can not find it myself.
I really need Upgrade HERM300 (T-Mobile MDA Vario II) on XP SP3 on my Laptop.
its boot loader shows IPL-1.04 & SPL-2.10.olipro
is it enough or not?
about 1 hours after reading your post I tried again upgrading on XP SP3 and put it on Boot Loader but nothing. (above Errors had shown again and again)
i would be appreciate if you show us that useful links (upgrading over XP SP3 normaly like XP SP2 successfuly)

Mate, as you have Hard SPL installed (SPL 2.10) try this instead...
1. Format a 2Gb or less sd card FAT32. Copy the .nbh file of the rom you want onto it and rename to "hermimg.nbh".
2. Put sd card into Hermes and reset to bootloader - power, OK and reset with stylus.
3. When prompted hit the power button to flash new rom.
Just make sure you have 50% or more battery though.
I find this method the easiest way of flashing roms as there is no real involvement of the PC except to format sd card and copy the .nbh file across. You'll get no sync errors, have no worries about resets/blackouts ar the usb cable being pulled. About the only ways to stuff this up is to reset in the middle of a flash or to have a flat battery.
Cheers...

reza_sadeghi said:
So really can you Upgrade your Hermes on Win XP SP3 successfully?
you mentioned some keywords but could you please show me those links exactly how to upgrade our Hermes on XP SP3 too?
I think this forum is so noisy i can not find it myself.
I really need Upgrade HERM300 (T-Mobile MDA Vario II) on XP SP3 on my Laptop.
its boot loader shows IPL-1.04 & SPL-2.10.olipro
is it enough or not?
about 1 hours after reading your post I tried again upgrading on XP SP3 and put it on Boot Loader but nothing. (above Errors had shown again and again)
i would be appreciate if you show us that useful links (upgrading over XP SP3 normaly like XP SP2 successfuly)
Click to expand...
Click to collapse
Yes you can upgrade it in XP SP3. Do you have .net installed in the pc? If you dont, then you will be getting errors too.

ultramag69 said:
Mate, as you have Hard SPL installed (SPL 2.10) try this instead.....
Click to expand...
Click to collapse
Wonderful.
and I like this method to upgrade PPC and prefer it.
I will try it as soon as i came back home and format 1GB Memory SD Card.
an Special thanks about your nice clear guidance.
i will back and declared any results.
ai6908 said:
Do you have .net installed in the pc
Click to expand...
Click to collapse
Yes.
.NET Framework 2.0 SP2 and 3.0 SP2 is installed on my XP SP3 shows on Add/Remove Programs on Control Panel.
I am sure.
and by your accepting we can upgrade PPC on XP SP3 , I resolute and will search and search again to find any solution why i get those errors on XP SP3 while you both told me upgrading is possible.
dear friends ,Thanks for your communion.

What you experienced was what I just did went thru
Had the same thoughts with the problem, I get Error [264], I also thought the CID-unlock issue. Tried many ways to get thru but fail in the end. Well yea, your piece of notes enlighten me. I will try on XP SP 2 and below, gotta find the machine some where first
Thanks for this post.
Reza_Sadeghi said:
I decided to tell something about my experience today about these Error numbers while Upgrading my Hermes (T-Mobile MDA VARIO II) .
Dear friends….i read Upgrading instuguidances again and again but there is a gold issue I did not notice untill today.
whenever I put my PPC into Boot Loader Mode and connect it to PC to upgrading these Errors appear immediately and I was in trouble what those errors are.
It checked the cable or some different Official ROMs but in fact I noticed all growth from Windows.
Yeah…
I am in winder why Microsoft does not make it possible upgrading PPC over Windows XPSP3 !!!
Whenever I run RUUWarpper on Windows XP Service Pack 3 these errors shown while I was sure about correct cable and correct ROM and ….
Sooo I want to share it to all peoples this gold notice :
Upgrading PPC is just possible on Windows XP Service Pack 2.
not Windows XPSP3 nor Windows Vista.
I think it is good for someone else that search and find these Topic in database of this nice/great Forum if same problem has appeared to him.
Here is some pictures of those errors & some proof if is required.
Click to expand...
Click to collapse

dear ferioz...
after those days passed what about your siuation?
has your problem solved using Windows XP Service Pack 2 ?
did you find any System running XP SP2 and try upgrading your PPC ?

If you have trouble with the pc, try the SD card method. Easier and I believe safer too as no-one accidently resets the pc in the middle of a flash. This method is a MUST when upgrading Radio ROMs...
For the PC though, you might need to update your .net framework to 3.5.
Cheers...

dear ultramag69...
You recommened this safely nice upgrading method and wrote a how to on this post and I love it and thank for suggest it.
I did not have enough time to upgrade and change my Hermes ROM recently from December 2008 so I did not try this method still cause PPC will go to Factory Default settings and programms installed will be ununstalled and I hate installing again and again.
anyway...
so Thanks for your nice answer and remind.
I suggest others try this method too instead of using PC running XPSP 2 specially this days mostly use Vista running Windows Mobile Device Center instead of XP running ActivSync.

Hellllllllp,260 error!

hi
i'll install a rom on my jasjam in win 7 but this can't connect to my phone [260 error] help me plz.. i can't change my windows..
and i have windows mobile device center and i'm sure my phone is connect to pc.. but i see 260 error..

Install Hard SPL V7 then use sd card method...

i´ve had the same problem in win 7. It was connected untill the device was set in the 3-colour-mode, and after a while error 260 was shown. I tried the same in win XP with ActiveSync 4.5 and everything was right. So if you have a pc with win XP, just try it there.

Odd this works fine for me in win7 but every once and awhile I'll get the same thing but all I have to doo is relaunch RUUWrapper and it works or just do it in tri screen.

ultramag69 said:
Install Hard SPL V7 then use sd card method...
Click to expand...
Click to collapse
Do exactly what Ultramag says or you run the strong chance of destroying your phone. See http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners for details.

use the [Easy Hard-Spl v7 beta v0.1] by qwasde2
it,s really usefull i tryed it,s by me
it,s for win XP and vista and se7en users
i,am not joking here is the link
http://forum.xda-developers.com/showthread.php?p=5136858#post5136858

qwasde2 said:
use the [Easy Hard-Spl v7 beta v0.1] by qwasde2
it,s really usefull i tryed it,s by me
it,s for win XP and vista and se7en users
i,am not joking here is the link
http://forum.xda-developers.com/showthread.php?p=5136858#post5136858
Click to expand...
Click to collapse
TNXXXXXXXXXXXXXXXXXXXXXX 100% WORKED.. Xx

Justphemy said:
TNXXXXXXXXXXXXXXXXXXXXXX 100% WORKED.. Xx
Click to expand...
Click to collapse
no problem

Windows7 Rom upgrading doesnot proceed 0%

I have Windows 7 RC1 64 bit version , I have installed Device manager 6.1 , I can sync with Diamond I have succesfully done Hard SPL, but in ROM upgrading Doesnot proceed and stop at 0 % and finishing wit error

Shomoha said:
I have Windows 7 RC1 64 bit version , I have installed Device manager 6.1 , I can sync with Diamond I have succesfully done Hard SPL, but in ROM upgrading Doesnot proceed and stop at 0 % and finishing wit error
Click to expand...
Click to collapse
i have win7 rtm 64-bit, and rom upgrades work. (also worked in the beta and rc1.)
by device manager, you mean windows mobile device center, yes?
it has an single upgrade via windows update, maybe that will solve the problem.
apart from these, you can also install the rom file (after extacting it) by copying it to internal storage with the name diamimg.nbh.

yes I mean windows mobile device center, I will try your Suggestion, but I really want to Know what is my problem , Hard SPL is done with no problem but rom upgrade could not be done

Internal storage method is faster, easier and safer.. why not thinking of that?

hy from what i now after flashing on w7 you have too install other driver for the phone when it is in bootloader then the ones that update installs. if the driver date is something with 2007 you have to take the driver from the mtty threat and install them in the Force driver signiture diseable (something like that) mode of the w7. when it boots hit f8 and from that list you will see what i meant. afterwords i recommend the internal storage flashing method(more simple and faster, in case of electicity stop less problems). hope this helps

p.s. after some interesting erorrs i found that a usb mouse when i was in signiture desabled mode of the w7 gave me troble. all went well after removing the mouse.... (microsoft mouse)...h..h.hh.

mauk said:
p.s. after some interesting erorrs i found that a usb mouse when i was in signiture desabled mode of the w7 gave me troble. all went well after removing the mouse.... (microsoft mouse)...h..h.hh.
Click to expand...
Click to collapse
thank you Mauk
I have upgradeed with internal storage methode, thanks again