Related
Can some pls help me how can I enter the bootmenu in Universal. I tried the combination given by wiki "camera + reset " but it doesnt works for me the device just soft rests. So pls can anyone help how can I enter the bootmenu pls.
thx
jeet
to get the bootloader you need to do power off + backlight + softreset.
i got the same problem as jeet got it, i cant get into the boot menu to get a sd bakup of my complete os
greetz
http://forum.xda-developers.com/showthread.php?t=549207
i know about that thread orb3000 but we dont talk about the BOOTLOADER, we talk about the BOOT-MENU where u can bakup ure ROM from current device to an SD card
i cant get into the boot menu if i push reset+camera !!!
thats the problem
grretz
didn't know Uni had a boot-menu
I believe for backing up ROM, you can use MTTY
I'm sure it's there in the wiki somewhere
Reset your device (using the SR hole) and then HOLD the camera button tight until you get the menu.
So the key thing is to HOLD the button after you hit the reset.
DOMy
you're joshing me? I have G3 and can't do that... (On WM6.51)
It simply boots up as normal. What does this 'bootmenu' allow you to do?
Hi, a friend have 2 pda universal from vodafone that he has flashed and killed. I don´t know what happend. pda always shows USB and v1.00. After a lots o rom updates still dead, i have JAFWM, but with or without this machine is dead.
any rom especial version?
any soft?
thanks.
1. Try to restart the device in bootloader mode(Light key, power and reset pressed together)
2. Look at the display (should say Serial and version at the bottom)
3. Disable the USB connection in Active Sync otherwise the update will crash.
4. Plug in USB Cable (Screen Should now show USB at the top)
5. Start original Upgrade from your provider or take the upgrade you want to use with the MA_UpGrade_noid.exe.
6. After Flashing restart device with both soft keys at the bottom of the screen ( Buttons with - on it) pressed.
7. When asked type 0 to erase all data.
9. Device should start normally, if it doesn't do not hesitate to ask.
device always start in bootloader mode, i flash all times without problems, but when i restart device, automatically puts on bootloader mode.
after flash, make factory settings but,after this, restart in same mode.
always, when i run update program soft MaUpgradeUt_noID, detects no rom in pocket loaded.
strange problem on 2 pda´s ?
thanks
That shouldn't be a problem. Just continue to flash the rom. There could be a problem with your bootloader and the upgrade version (AKU2) you want to use.
Maybe it's a problem with bootloader.
Try it, maybe it will help you.
http://forum.xda-developers.com/download.php?id=11414
i think same as you, only problem with ROM image, but i have flashed many roms but I can´t revive device. So i ask name of Rom tht can revive pda.
Br.
PD. how i can flash the archive attached?
The rar file mentioned above is only the bootloader you already got on your device.
In your case i would use an old AKU1 rom and to see if it works.
hi guys
i have same problem. show only boot loader mode. how to use this boot loader file. wich AKU1 file is working. my phone is MDA PRO from germany T-mobile, i wan't to update ro to English. after flashing many times, many rom no result. help me
thanks a lot
Hello Siemens Man
Which Bootloader do you have ?
It would be great if you could make an backup of your bootloader then, that i could downgrade my phone and try to unlock it.(If do not know how to make an backup, thats no problem, because i can show you how to do it)
greetz
hi man
i have in boot loader mode. show me usb v1.00 only. i don't have buck up for my phone. please tell me solution how repair my phone.
thanks a lot
Did you try to update your phone to the latest orange rom for testing yet ?
If not try it out (I know it is said to be slow, but only if all orange customizations are installed) If it runs then its ok.
Otherwise try to use the exitbl.exe mentioned somewhere in this forum, hopefully it works.
connect to mtty and issue set 14 0 and then restart the device or use exitbl utility by buzz
hi guys
thank you for reply mail. all problem solved. now good working
thanks to Buzz
are there any useful hints extrem69 ?
no usb mode
What can i do of my Qtek 9000 doesen't change from Serial to USB mode?
siemens man said:
hi guys
thank you for reply mail. all problem solved. now good working
thanks to Buzz
Click to expand...
Click to collapse
I had same problem like you, can you tell me what exactly did you do so you can repaire your phone.
I used T-mobie and didn't work after upgrade rom too, it's alway stop in boot loader screen. I tried up rom of T-mobile, Imate, Dopod but nothing to work, I don't know how to repair it, it's still can up rom normaly, nothing wrong while upgrade, it's only don't work after finish.
wooooooooooooooooooow
many thanks
i tried many ways to solve this problem
with your advuse it is working now.................
Lt.Cmdr.Ivan said:
1. Try to restart the device in bootloader mode(Light key, power and reset pressed together)
2. Look at the display (should say Serial and version at the bottom)
3. Disable the USB connection in Active Sync otherwise the update will crash.
4. Plug in USB Cable (Screen Should now show USB at the top)
5. Start original Upgrade from your provider or take the upgrade you want to use with the MA_UpGrade_noid.exe.
6. After Flashing restart device with both soft keys at the bottom of the screen ( Buttons with - on it) pressed.
7. When asked type 0 to erase all data.
9. Device should start normally, if it doesn't do not hesitate to ask.
Click to expand...
Click to collapse
HI to all! I have lost bootloader upgrading my qtek 9000 vodafone.
can i to solve problem? No bootloader menu, i have tried power+reset+lamp, power+reset+camera - herd reset with - + - reset without effect. Pse help me!!! Thanks.
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
blanktruth said:
Ok, first of all I did not think that it was this dangerous to use MTTY!.
I followed everything and came to these lines
---------------------
Cmd>task 8
Cmd>
---------------------
But after Cmd>task 8 my device restarted immediately before the second line Cmd> appears and I panicked and disconnected my device and pushed the wrong buttons while "Touch Diamond" logo was on the screen.
Now, nothing happens. I can not start from the beginning because I can not start the bootloader by pushing Vol Down and the small red reset button...
Is there anything else left for me to try? Or should I throw my HTC to garbage?
Click to expand...
Click to collapse
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
i have the same probnlem!! with my diam300
my bootloader show not Diam300 64m but only 64M on the first position in 3color mode... plz help
Connect the Diamond and run the customruu.exe from your desktop, this should work.
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....
blanktruth said:
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
Click to expand...
Click to collapse
The only thing to do now is to flash back a stock ROM or use a custom ROM with the RUU.
Solved!...
Dom1n8tr1x said:
First of, your device is supposed to soft-reset after the "task 8" command and you should have been holding down the "Volume Down" and "Back Buttons" to begin flashing your new ROM. The whole idea of using MTTY is to format your Main Storage and flash a new ROM. Therefor you should have loaded the ROM that you wanted to flash onto your Internal Storage.
Click to expand...
Click to collapse
Thank you for your reply.
Actually I had uploaded the ROM to my internal storage, but during trying to bring my phone to bootloader mode, I formatted the internal storage...
Anyway, what I did now is, first I opened the USB Connection feature from ActiveSync, and then used CustomRUU.exe to Flash the ROM...
Everything is solved now...
Thank you very much all...
ilijan said:
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....[/QUOT
bootloader is all you need to revive the phone
connect it to usb in bootloader mode and just install an oficial diamond rom from an windows xp pc.
it's easy
Click to expand...
Click to collapse
plz write here step by step guide how you solved
How it was solved...
ilijan said:
plz write here step by step guide how you solved
Click to expand...
Click to collapse
Actually the most crucial part was to bringing phone to boot loader mode. And I think I managed that by pushing the Volume Down and Back (the arrow pointing left) buttons immediately after restarting my phone. And I had to do this after taking out the battery and putting it back after 5 sec.
When I pushed these buttons at the start up the phone tried to install the ROM from my internal storage, but as I explained I had deleted it by mistake. Therefore it could not find the ROM. I disconnected my phone from my PC and the screen started to say something like Retrying USB connection or waiting for USB connection, something like that.
I restarted my PC in Digitally Signed feature disabled by pressing F8 during start-up. Reconnected my phone to PC (the screen of the phone was still blinking as waiting or retrying usb connection). And voila the phone screen changed to boot loader mode...
The rest was easy. I opened the USB connection feature from ActiveSync and used CustomRUU.exe with a ROM to flash my phone...
That is all...
1. plug phone in to computer in bootloader
2. run customruu or stock from rom update on computer
3. wait for rom to flash to device
4.???
5.profit
but my booloader dont show model ID: DIAM300 64M what i had befor
and show me only: 64M
and any flash error with invalid model id, i canot flash, rom, stock rom, or hardspl...
understand me.. im not totaly noob... i used mtty X times... but now have this probles
can somebody help me?
my diamond dont have model id...
before i had in bootloader mode DIAM300 64M model id, but now i havent got... its show only 64M,
every rom flash stopped at 1% cose model id error,
every hard spl falsh finished 100% but after flash when device restart write model id error...
i cant do anithing... can somebody help me?
For everyone facing problems after flashing his/her device, take a look at the link in my sig.
There you can find a guide to restore your diamond.
you dont understand me..
i canto flash any rom any hard spl becous my diamond dont have device ID...
in bootloader dont show DIAM300 64M but only 64M
after all flash say error mobile ID...
i try mtty, hard reseted, soft... and nothing
after start its show me only first stock screan, the red text on the right bottom sight dont start: 1.17.25.14
2.100000
geny d2x
its maybe wrong but i forgot what waz here...
how can change device model ID? form 64M back to my stock DIAM300 64M?
Try another version of Hard-SPL, some people report that 1.40 not fully works.
I suggest you try 1.94 Olinex.
my diamond is death... if somebody know how can heal it... plz write me...
my device ID is missing... so i cant flash any rom, any hard spl, any radio...
try this? http://forum.xda-developers.com/showthread.php?t=409425&highlight=invalid+model+id
im not sure but i dont think one can brick his/her phone after hard spl, thats the reason of hard spl in the first place that u dont brick it. boot loader is always present
Guide
if you are using Windows XP try the following steps:
Connect your device to your PC
In Active Sync > connection settings > check Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.
Guide
if you are using Windows XP try the following steps:
Connect your device to your PCIn Active Sync > connection settings > check
Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..
...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?
I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get
hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work
...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn
Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p
ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000