Develop Bugs

did i bake my phone

Hello, I was updating my rom with Kavana 080408 and it got to 9% then I have to recover it, it successfully recovered then around 3% it just shut off and now I can not turn it on or do anything, I have pluged it into the wall charger and still can not turn it on? is my phone officially cooked? anything suggestions?
Mathew

milewski05 said:
Hello, I was updating my rom with Kavana 080408 and it got to 9% then I have to recover it, it successfully recovered then around 3% it just shut off and now I can not turn it on or do anything, I have pluged it into the wall charger and still can not turn it on? is my phone officially cooked? anything suggestions?
Mathew
Click to expand...
Click to collapse
Try removing the storage card (microSD/SDHC), then holding down this combination of keys: both soft keys, camera key--then press the power button.

Dont forget to place your forefinger on your nose before the restart
*Joke*

Rip Syntaxx said:
Try removing the storage card (microSD/SDHC), then holding down this combination of keys: both soft keys, camera key--then press the power button.
Click to expand...
Click to collapse
Nothing happened... I did it for upwards of 30 seconds... is it a hopeless cause? Time to part it? GR i hope not!
Mathew

Mikey1022 said:
Dont forget to place your forefinger on your nose before the restart
*Joke*
Click to expand...
Click to collapse
this dint work either

hold camera button plug usb in and then the phone sould go into bootloader then flash your origianl phones rom
hope this helps

Your Phone Is Not Dead
milewski05 said:
Nothing happened... I did it for upwards of 30 seconds... is it a hopeless cause? Time to part it? GR i hope not!
Mathew
Click to expand...
Click to collapse
Press all the keys on the power up, right and left soft keys, camera button and the power button, all at the same time, again do this on the power up! When you see the color screen, connect your device to your PC via active sync and install a 6.0 ROM on your device, do not try to install a 6.1 ROM on your device at this stage of recovery. The green active sync icon my not show or look like your device is connected to your PC but it is connected, just install a 6.0 ROM on your device. After you install the 6.0 ROM on your device, now you can again try to install a 6.1 ROM on your device. Be patient it will work, your device is not dead.............!

Technology said:
Press all the keys on the power up, right and left soft keys, camera button and the power button, all at the same time, again do this on the power up! When you see the color screen, connect your device to your PC via active sync and install a 6.0 ROM on your device, do not try to install a 6.1 ROM on your device at this stage of recovery. The green active sync icon my not show or look like your device is connected to your PC but it is connected, just install a 6.0 ROM on your device. After you install the 6.0 ROM on your device, now you can again try to install a 6.1 ROM on your device. Be patient it will work, your device is not dead.............!
Click to expand...
Click to collapse
I am still getting nothing... even when I plug in the phone to a USB power source the green power indicator light is not showing! I press L/R SoftK plus Cam and PWr Buton and nada!
[email protected]

milewski05 said:
I am still getting nothing... even when I plug in the phone to a USB power source the green power indicator light is not showing! I press L/R SoftK plus Cam and PWr Buton and nada!
[email protected]
Click to expand...
Click to collapse
PS the soft keys do not unclude the home key and back key do they?
[email protected]

milewski05 said:
PS the soft keys do not unclude the home key and back key do they?
[email protected]
Click to expand...
Click to collapse
try this take out you battry put back in then hold camera button plug usb in then flash your origianl rom

rickwyatt said:
try this take out you battry put back in then hold camera button plug usb in then flash your origianl rom
Click to expand...
Click to collapse
DUDE I GOT IT!!! the battery was the problem.. I wonder why? I took out the battery and then held the camera button down and it worked instantly WTF! LOL
Mathew

milewski05 said:
DUDE I GOT IT!!! the battery was the problem.. I wonder why? I took out the battery and then held the camera button down and it worked instantly WTF! LOL
Mathew
Click to expand...
Click to collapse
happy it work for you

haha. rickwyatt should be getting paid. hes the fix all.

ROM Upgrade Please help

I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help

Did u Hard Spl your device before begining this process?
Step 1: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.

band27 said:
Step 1: did u Hard Spl your device before begining this process? if yes to step 1 then move on.
Step 2: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.
Click to expand...
Click to collapse
I tired the hard reset, I got a white screen with a message saying press volume up button to restore phone to manufacturers defaults, when I did that I got a message Restore...Completed Press VolUp to boot.
When I press the Volup button the phoen does not boot, it comes to the Touch Diamond screen and there is not ROM message at the bottom of the boot screen.

Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.

band27 said:
Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.
Click to expand...
Click to collapse
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again

mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
Yeh, that is not your Bootloader Screen. Here, do it like this. Soft reset with stylus first....quickly let go of that and press Vol. Down in that order. When u see the Bootloader Screen you can let go of the Vol. Down button.

mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
The phone is booting again and again, only if I remove the battery it can be stopped.

So it won't let you go to the Bootloader Screen then? Hmm...?
So you soft reset it and pressed vol down and it just reboots constantly?

I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429

mukesh_thiru said:
I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help
Click to expand...
Click to collapse
dI have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Mukesh i have one solution for that download hspl package from here http://ds8.fileflyer.com/d/e3858be1...c/u56S/js0hkAj/diamond-hspl-1.23-and-1.24.zip extrace in other folder in ur pc than just connect ur phone to ur pc via cable and just click on dimond-sspl ms-dos batch file than follow the steps ur phone will connect via cable than follow this step 1. download unsigned hard spl v .1.93 olinex from here http://ficca.bounceme.net/download/HARDSpl_Diamond_OliNex_1.93_Unsigned.zip extract in other folders than connect ur phene via active sync than run Ruu if u got 100% job done try it tell me by post message what about ur prob good bless u

mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first post if you told us your phone was CDMA.

mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first thread if you told us your phone was CDMA. But you didn't think there was a difference probably because you didn't read much beforehand.

Bricked MP6900SP

My friend got a MP6900SP, and he tried to download a rom and flash it.
Now the phone is bricked, can't power on.
When connect to PC, nothing happened.
If I press power + volumn down + reset, PC will found a device.
No bootloader screen (tri-color), screen is totally blank.
RUU can't found the phone.
I did some research, but got confused.
Most post are for Verizon phone, not sure if they work the same for spring.
So, I am just checking to see if there's a way to revive my friend's phone.
Thanks all for the help!!

try to update via SD card
search for updating the bootloader via sd and also updating roms via SD
sounds like you may need to try updating the bootloader via SD first
good luck

chocobozero said:
My friend got a MP6900SP, and he tried to download a rom and flash it.
Now the phone is bricked, can't power on.
When connect to PC, nothing happened.
If I press power + volumn down + reset, PC will found a device.
No bootloader screen (tri-color), screen is totally blank.
RUU can't found the phone.
I did some research, but got confused.
Most post are for Verizon phone, not sure if they work the same for spring.
So, I am just checking to see if there's a way to revive my friend's phone.
Thanks all for the help!!
Click to expand...
Click to collapse
Have you pulled the battery and let it sit for a minute then put the battery back in and tried to power on?
Blank screen and cant power on? sounds like something far more than bricked from the ROM he tried...
If you can get the screen I would try the suggested route with the flash from bootloader/SD card technique but if you cant get a screen at all no matter what and swapped out batteries as well (have seen a bad battery cause similar issues and may be a coincidence this is happening during a flash attempt)
Detroit Doug

To enter bootloader:
Power+Camera, then reset. No volume button.

TheChampJT said:
To enter bootloader:
Power+Camera, then reset. No volume button.
Click to expand...
Click to collapse
Thank you!!
bootloader mode flash was successfully revived the phone.
Not sure what "power + volumn down + reset" mode is, but PC does show fine a data interface when I press them.
Anyway, thank you all for the help!!
You guys are good!!

chocobozero said:
Thank you!!
bootloader mode flash was successfully revived the phone.
Not sure what "power + volumn down + reset" mode is, but PC does show fine a data interface when I press them.
Anyway, thank you all for the help!!
You guys are good!!
Click to expand...
Click to collapse
i dont know how to put my mp6900sp in bootloader mode i tried the above still doesnt work only the start up screen and then it stays on

I don't know what the OP was saying about the volume button.
But just to be clear: if you are stuck at the bootup screen, having problems connecting and/or need to flash via SD card.....you want to quickly press and hold the top Power button + right side Camera button, then the bottom Reset button. The phone should display the rainbow screen and will say "Serial" on it until you plug the phone into your computer, when it should change to "USB".
For more help see this post and because I recommend an NFSFAN ROM this thread and this thread.

[Q] BAD Flash when updating radios, who can I pay?

BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.

[email protected] said:
BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.
Click to expand...
Click to collapse
is your phone a gsm rhodium or does it have a cdma module too?

Both I believe

This happened to me last night. I reflashed the ROM to fix it. I used MightROM which is FRIGGIN' Awesome if you ask me
In order to do that though you need to be CID unlocked though but basically as long as you are in the bootloader/bios then you can flash the new ROM from your PC via the USB. If you need any links to that stuff I can post, but I am not quite sure if this would be part of XDA or not (Is MightROM xda? Idk? PPCGeeks??)
You can also try holding down the Call answer and Call end buttons at the same time with the power button then put your battery in. This didn't work for me though, but I had to do this anyways after I flashed the ROM so it might work.
edit: Sorry I misread. I am not sure about the Black Screen. Might work though. I was in the bootloader/tricolor to reflash. Maybe your LCD is dead or something for all I know. Sorry Mate.

[email protected] said:
Both I believe
Click to expand...
Click to collapse
oh god then you flashed a GSM radio to a CDMA worldphone (just because it has a GSM module doesn't mean you can flash a GSM carrier radio to it... nope!!)
if you plug it into the PC does the PC try to install some USB driver?

[email protected] said:
BAD Flash when updating radios, who can I pay to fix this?
Or anyone know of a way to fix this?
It appears to be bricked
When I flashed the ATT_Radio_Rhodium_4.48.25.95, I didn't rename it to RUU_Signed
Now I get nothing when I restart the phone, just a black screen.
Click to expand...
Click to collapse
It is simple. You obviously have a CDMA device. It doesn't matter if you use it on a GSM network. Your device is and always will be a CDMA device. NEVER try to flash ANYTHING GSM on it or you run the risk of permanently bricking it.
To fix this, you will need to grad the latest ROM update from either HTC's website, or your carrier's website. Put the device into bootloader mode by holding down the power button and pressing the tiny reset button under the battery cover with your stylus. Once it boots into the tri-colored screen (bootloader), you can then run the ROM update utility that you just downloaded. This will restore everything back to stock settings and you can try again. If you have already done Hard SPL, then it will NOT be overwritten, so don't worry.

Update
I cannot get into the tri-colored screen (bootloader).
How long do I need to hold in the reset and power button?
More than 1 min?

[email protected] said:
I cannot get into the tri-colored screen (bootloader).
How long do I need to hold in the reset and power button?
More than 1 min?
Click to expand...
Click to collapse
You can't get there, because you're doing it wrong. You need to hold down the volume down button and then press the reset button once. This gets you into the bootloader.

Update
Holding down the volume down button and then pressing the reset button once, did not work for me.
How long do I hold the volume down button for?

[email protected] said:
Holding down the volume down button and then pressing the reset button once, did not work for me.
How long do I hold the volume down button for?
Click to expand...
Click to collapse
Do you have power in the device? You need to have a battery in it. Also, the reset button might not power your device on. If your device doesn't turn on when you press the reset button, then just hold the volume down button and press the power button once instead. That ought to do it.

[Q] Htc one x is dead! Please.. Help..

Hello everyone.
I apologize for my bad English.
My Htc is dead and will not turn on. I make a list with the details hoping someone can help me.
** The phone will not turn on and the display remains black.
**The phone does not emit any sound and makes no vibration.
**If I connect the charger the phone is charging properly. You turn on the red light and after 10/15 seconds the green one.
**If I connect the phone to the PC 4 devices are recognized but one is not installed. (Attach photo)
**Try and try again to connect the phone to the PC on one occasion, the display has flashed 3 times and for a split second it appeared the inscription HTC.
---- List of tests done:
*I tried to hold down the power button for several seconds (10 to 40).
*I tried to press both volume keys and the power button.
*Replaced FLEAT the power button.
I really hope that someone can help me!!
Thank you!! Thank you!!

Does anyone have any advice?

Can you enter hboot?
Sent from my One X using XDA Premium 4 mobile app

Usura666 said:
Does anyone have any advice?
Click to expand...
Click to collapse
Try to go in bootloader when the phone is off pres volume down + power button until you go in bootloader if you can go in bootloader you can Unlock bootloader after this flash Philz 5.15.9. recovery and then custom rom or nand backup and it will be good when you are in bootloader to post here result from command fastboot getvar version-main

I tried to get into bootloader mode but nothing happens ...

You need to hold power and volume down until you get into bootloader
Sent from my One X using XDA Premium 4 mobile app

Usura666 said:
I tried to get into bootloader mode but nothing happens ...
Click to expand...
Click to collapse
and disable fast boot in power settings

Thant said:
and disable fast boot in power settings
Click to expand...
Click to collapse
The phone will not turn on. The only thing that happens is that charges the battery and if I connect it to the PC recognizes 4 devices.

Usura666 said:
The phone will not turn on. The only thing that happens is that charges the battery and if I connect it to the PC recognizes 4 devices.
Click to expand...
Click to collapse
ok then press power button for 10-15 sec to turn off the phone after this press volume down + power buttton until you are in bootloader

Thant said:
ok then press power button for 10-15 sec to turn off the phone after this press volume down + power buttton until you are in bootloader
Click to expand...
Click to collapse
I tried. Nothing happens.
[

Usura666 said:
I tried. Nothing happens.
[
Click to expand...
Click to collapse
please post picture on your phone when you go in bootloader not on the computer

portssra with
Thant said:
please post picture on your phone when you go in bootloader not on the computer
Click to expand...
Click to collapse
No, I can't because it doesn't switch on.

Usura666 said:
No, I can't because it doesn't switch on.
Click to expand...
Click to collapse
man are you able to go in bootloader???? yes or no what happend when you pres volume down + power button hold the keys until you go in bootloader

Thant said:
man are you able to go in bootloader???? yes or no what happend when you pres volume down + power button hold the keys until you go in bootloader
Click to expand...
Click to collapse
Nothing happens. The phone remains off.

Usura666 said:
Nothing happens. The phone remains off.
Click to expand...
Click to collapse
are the phone have battery connect the phone to charger and hold volume down+power button and report back
If again not see anything on the display after this maybe fault display or BSD/black screen of dead/ try do pressure between the display and the right down side on the main camera

Thant said:
are the phone have battery connect the phone to charger and hold volume down+power button and report back
If again not see anything on the display after this maybe fault display or BSD/black screen of dead/ try do pressure between the display and the right down side on the main camera
Click to expand...
Click to collapse
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?

Usura666 said:
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?
Click to expand...
Click to collapse
you must to see something on the display see have new thread for apx mode PJ4610000

My 2 cents
Usura666 said:
I tried. Nothing happens.
I have read some posts that talk about the APX mode. Could it be my case?
Click to expand...
Click to collapse
You never stated what happened to get your device in the state it is and i'm just assuming you did something to brick it, so here
So firstly you need to get the drivers for your device installed.
my advice download WinDroid Universal HTC Toolkit v1.1. It will allow you to easily know if your pc is recognising your device.
Once that is done you need to get your device changed sufficiently.
Go to http://www.hackmyandroid.com/comprehensive-guide-on-unbricking-the-htc-one-x/4216 and follow the instructions.
Charge HTC One X in Fastboot Mode section from the link should help you charge your device
With the ADB folder where it should be on your computer C drive and your device plugged in and recognized, charging shouldn't be a issue
this should cause your device to restart repeatedly until it reaches about 10% battery
I advice once you have completed the charging of your device to the 10% mark that you continue on to the Unbrick the HTC One X as well as the Restoring the nandroid backup sections. You can always install a custom rom like CM11 or a sense based rom instead of doing restoring a nandroid backup
Hopefully your device will be up and running
Goodluck and let me know how it went.