unknown problem - P3300, MDA Compact III General

dear friends ,
my phone has shut down and only when you take out the battery and put it back in after which you press any button on the phone it comes on and shows the htc logo after which it displays the following
ipl 3.07.001
spl 3.07.000
gsm 02.69.90
os 3.7.0.0
remains on for about 5-6 seconds and goes off
have tried to enter the boot loader mode by pressing the record button and reset button but it continous to behave in the same manner as mentioned above .
also when i try to charge the phone it shows only a red light
hoping someone can offer a solution to my problem
thanks and regards

I'd also be interested to know about this as my MDA Compact III has just done exactly the same thing.

have you guys tried flashing...that could kill it if not done propertly....but i doubt,the led is on,splash screen appears...info appears...what were last few things you did
according to spl os and ipl you flashed artemis touch 4.02 if i'm not wrong...or maybe tom's v5...try reflashing the same rom or just try a hardreset

Interesting...I've recently flashed the same ROM (v4.02)
I am certain I followed all the instructions about USPL and its been working fine for about a week...then it just went blank!
Will try re-flashing and/or a hard reset.
Thanks for the advice.

mrd5477 said:
Interesting...I've recently flashed the same ROM (v4.02)
I am certain I followed all the instructions about USPL and its been working fine for about a week...then it just went blank!
Will try re-flashing and/or a hard reset.
Thanks for the advice.
Click to expand...
Click to collapse
well...if it worked i'm sure you installed some app or deleted some files...so the system doesn't work...
if so hr will help

dear friends,
took the device in for repairs the fault was with the power circuit board which had to be changed as`informed to me by the technician
i now remember a few months ago the power button stopped working and a few days before the phone went bad it would work intermittently but there was no spring in the button hence it would have to be pressed quite hard for it to work i feel that this loose power button caused the power circuit to fail also my sd card was spoilt and the same had to be replaced
cast me appx in usd 30 for the repairs
thanks

Related

My Qtek 9000 died after upgrade

Hi to all. After that i have upgraded my Qtek 9000 Vodafone with NoID software, at 99% the device it is blocked. No Boot Display. No Lamp.
I can to solve the problem? How i can enter in boot loader mode forced?
Pse help me!
Thanks.
Power + Light + Reset
rikram said:
Power + Light + Reset
Click to expand...
Click to collapse
Died.
Boot rom is cancelled from PDA?
There is a another mode ?
Help Me!
Help me!
Another Idea?
Power+light+reset = bootloader mode as already posted. It does not light up though, you can only see the bootloader screen if you look at it in bright sunlight or shine a light at it. Try charging it overnight the press power+light+reset, connect it to your PC then run the upgrade. If it really isn't going into bootloader mode then you will probably need to send it off for repair to vodafone.
i just had exactly the same problem, even the pc does not recognize it at all, activesync doent work, what to do please
lion2000 said:
i just had exactly the same problem, even the pc does not recognize it at all, activesync doent work, what to do please
Click to expand...
Click to collapse
I do not have hopes. There is not image on display. I have tried with power+reset+lamp hard reset - + - + Reset!!! Power+ camera + Reset!!!
Display black and nobody written of the boot loader.
Useless if the boot loader it is cancelled is not restorable. Unfortunately it goes in repair.
i have the same problem with my MDA PRO. my MDA PRO also does not show bootloader screen. even not is charging by its charger. i just wanted to upgrede it with AKU and after i upgraded it, it did not open even bootloader screen did not appear.
fuhayer said:
i have the same problem with my MDA PRO. my MDA PRO also does not show bootloader screen. even not is charging by its charger. i just wanted to upgrede it with AKU and after i upgraded it, it did not open even bootloader screen did not appear.
Click to expand...
Click to collapse
I have not solved. I sent device to assistance.
mne now shows the boot screen, it comes with some funny colours, but it stays there, whe i ckicj sof+soft:reset it comes with screen
press o to restorefactory default
press x to exec
when i press 0 it goes back to that funny colourd screen, dont no what to do
any help?
what is soft+soft ? how did you get boot screen ? which phone are you using ?
How it can happen? If device worked before u start upgrading maybe u battery is low. Try to charge it somehow even not fully and continue upgrading via bootloader screen.
yes, universal. good news, i got it back to life, it now an i mate, can't change it, but it works.
i tried many rom version that i downloaded from buzzdev and one clicked.
most came with country id wrong etc
how can i gdt it back to O2? it does not accept it anymore?
tabasco said:
How it can happen? If device worked before u start upgrading maybe u battery is low. Try to charge it somehow even not fully and continue upgrading via bootloader screen.
Click to expand...
Click to collapse
Shalom tabasco, well not really, i had it like that for a week, i evenhad it on charge for almost 3 days, the screen came at one point when i upgraded a rom, but the screen had a funy colour and it was stuck in bootloader, done all reset you can imagin, i even rand O2 to collect it for repair
seems to me that I created a problem for myself too. Can't escape bootloader mode. This 3 stages runs fine, but after final 100% CE screen, when I doing hard reset, writes "Clearing now" and goes back to bootloader screen :roll: How to make him alive? I even did short on backup battery (opened back cover), but nothing effective
ok ok i pressed several times buttons which activates bootloader and it comes to normal activity. Was it a joke or something else ?
Good for you
Did u try to do as given here? http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen - do all this, maybe it will solve. Be ezrat ashem
But anyway I'll going to make him swallow this new ROM from T-Mobile, but later, not at work... :wink:
hi,
did you solve your problem yet ?

XDA exec dead

Hi all
Recently I bought a XDA exec from eBay (used) It was working fine but I found light button was not working. (Very imp)
By mistake I cleared the memory of the device and same time did a soft reset
Then the device was got stopped at O2 screen at the start it self and not going further.
Then I removed the battery and also did a hard reset it dint helped after similar tries my XDA exec was dead with no screen at all now (just blank)
The only thing I could notice is when ever I plug the charger or USB cable from PC a red light blinks for few sec
I want through this site and got to know the issue is with the boot loader
Know the major problem to me is, to get into the boot loader (i.e. Light + power + reset) but as I said my light button is not working from the beginning is there any other way to get into the boot loader
Can any one help me in fixing this problem would be great help
Thanks and Regards
syed ([email protected])
no one knows wt do with this
Same thing happening to me!!
It was stuck on Boot Loader, then i cleared out the rom with "task 28 55aa"
at first i can see some words ("serials"), but now completely BLANK!!
The only thing i can do is go to "Clear storage" mode, either i typed 0 or x, both goes BLANK!
What im afraid is if the battery got empty because of re-trying..
Anyone please help us!....
did you reflash a ROM after task 28 55aa?
Im afraid so, yes.
I did "task 28 55aa" twice..
Any chance to make it right?
Ok, i just did (reset+power+light) and now i can see "Serial" and "v1.00" at the bottom.
I can see USB connection when i connect through "mtty"
Now what should i do?
Everything OK now.
If anyone have the same problem, PM me.
Ill be glad to help.
Now reflash the rom (upgrade) with the rom upgrade utility
syed_mail said:
Hi all
Recently I bought a XDA exec from eBay (used) It was working fine but I found light button was not working. (Very imp)
By mistake I cleared the memory of the device and same time did a soft reset
Then the device was got stopped at O2 screen at the start it self and not going further.
Then I removed the battery and also did a hard reset it dint helped after similar tries my XDA exec was dead with no screen at all now (just blank)
The only thing I could notice is when ever I plug the charger or USB cable from PC a red light blinks for few sec
I want through this site and got to know the issue is with the boot loader
Know the major problem to me is, to get into the boot loader (i.e. Light + power + reset) but as I said my light button is not working from the beginning is there any other way to get into the boot loader
Can any one help me in fixing this problem would be great help
Thanks and Regards
syed ([email protected])
Click to expand...
Click to collapse
Try reflashing with Jwrights rom upgrade (I don't think it requires going to bootloader) or any of the upgrade utility that does not require going into bootlader.
how do i do it
can u give me the procedure to do it
thanks
I have a probleme MY pc dosent detect the universal when i connect
it dispayes unrecgnised device
any help would be great

Help - Artemis doesn't boot / turns on

Since this morning I've got a serious problem:
My last flash was on February (Artemis touch 4.01). Everything worked fine till this morning. I turned the device off to change the sd card. After that I couldn't turn on the device (black screen).
I removed the battery for one hour - no luck.
After a hard reset it begins to boot, but on the first screen I only see 2 Version (IPL and SPL). After a while, for a millisecond I can see the version of GSM, than immediately the screen turns black. After a while the Charge LED turns on for a short while (without connected cable!). Then nothing.
I can get into bootloader and successfully flash the original shipped O2 GER rom, but after flashing the same.
Has anybody any ideas or do I have to send the phone for repair?
Regards
Andre
There are some posibilities:
1) The device has a serious damage. Could be flash memory or boot section of flash memory. In this case, repair could be useless or only done by service.
2) flash was not that successful you finally thought. To Access Bootloader you have to press Powerbutton and Voicebutton (other side) at the same time and press simultaneously the reset button. When Device is rebooting, press power an voice buttons at same time, several times until bootloader opens. See wiki, it worked for me.
3) flash WM6 image from HTC. This one accesses bootloader by itself and is easy. I don't know if this will work for you.
4) battery could have a damage. The battery of artemis is very damageable. maybe try to change against a new one, maybe with more capacity.

Help with HTC Touch Diamond, won't boot

Hello, this is my first post here. I tried to install Windows Mobile 6.5 as indicated in Gizmodo http://gizmodo.com/5281397/how-to-install-windows-mobile-65-right-now but it didn't work and now my phone won't boot.
The phone is an HTC Touch Diamond from Sprint. I followed all the steps indicated and everything look fine, but after installing the OS the phone displays the screen TOUCH DIAMOND, and then restarts and displays the same thing. I'm able to get into the boot loader (Tri color screen) and says:
DIAM500
SPL-0.57.CMONEX
MicroP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20.
I don't know what to do now
Thanks
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Flash from Olinex 1.40 screen?
okokur said:
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Click to expand...
Click to collapse
Hi I have the same issue on my HTC Diamond. I flashed wm 6.5 and it was working fine, then it hanged on titanum weather. I reset and it stayed on the HTC Diamond page, I did hard reset and got the Olinex 1.40 3 color page. It does respond from serial to usb when I plug/unplug. Can I reflash without active sync?
Turns out I was able to flash, but both roms I tried work well on 1st install, but stay stuck on the Touch Diamond screen everytime I restart de device. Is it a problem with the radio not compatible , or is there a specific Hspl for each ROM???
I found solution for this problem. If your diamond won't boot go to bootloader mode and upgrade your radio http://modmydiamond.info/index.php?option=com_content&task=view&id=15&Itemid=26 and after that your dimond worked fine without loosing data.
try to hard reset the phone by pressing vol down key + the center button + reset button.
if the problem is still like dat..
try to install another rom..
davidwong007 said:
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
Click to expand...
Click to collapse
Thanks davidwong007 for your help, I was experiencing the same issue as op and your method did the trick. For a minute there I thought I had bricked my HTC Touch. I did step by step what you suggested and ended up in the rainbox screen, once I was able to do that, I knew there was a hope. i did a full factory reset of the phone and voila the phone fully booted, the pain in the butt touchflow loaded. Very important thing I forgot to do in the past is to back up my phone, after the restore you will lose everything on phone, except what is in the internal storage. Thanks again.

Help! Diamond Not Starting Up

I recently tried to unlock my uncle's Diamond. I used Hard SPL1.4 from this site, and it finished that successfully. After restarting, I went through the whole screen calibration and so on, then I went to the kitchen to get some food. By the time I got back, the Diamond wouldn't start at all. I haven't tried a hard reset, but I don't think that would do me any good since the phone doesn't start up at all. Is there anything I can do? Or will I have to tell my uncle I ****ed his phone..
Just a quick detail, I did notice that after it started up again, the area next to the SIM card slot heated up quite a bit. I don't know if that's related, but I figured I'd tell you anyway.
The Hard SPL of choice is the 1.93. Any who, try and place the device into bootloader mode (tri-colour screen).
Hard Reset Your Device:
• Soft reset button and hold the vol. down + Circle button until u see the grey screen. REMEMBER THIS WILL ERASE EVERYTHING SAVED ON THIS ROM (i.e. contacts, calender, etc.)
Bootlaoder Mode:
• Soft reset and hold the volume down until u see the tri screen
Do you see the Hard spl 1.40? if yes, then just a hard reset and see what happens
IF none of the above worked, take out the BATTERY for a bit and try the above options all over again.
Hi, thought i would add to this thread.
Mine also did this, it worked fine for a week with Windows Revolution 6.5 rom then it randomly turned off and refuses to turn on.
Bootloader mode / hard / soft reset none work.

Categories

Resources