Develop Bugs

I need help with my BA here in the philippines

I was trying to upgrade my XDA IIs using my card reader but when I run the file named GetBL my XDA went off and it displays "serial" at the top and "v2.07 at the bottom. How can I put everything back to normal? Is there anyone in the Philippines that could help me? Thanx...

did you try hard reset?

Yes I did but nothing happened. Will you give me a hand on this. Is there any other way to put it all back? Thanx....

dude we have the same prob ill tell u wat 2 du if i fixed it...have u tried gh?

I haven't tried it dude. What's gh dude? Will you give me a hand on this. I can't figure out what's the problem. Thanx...

gh=greenhills
do you have a usb cable?is your BA still detected by the computer when plugged using the usb cable?

I haven't tried it yet but I have a cradle and usb. But what if it's detected. What should I do? What will I also do if it's not detected. Thanx

villain08 said:
I haven't tried it yet but I have a cradle and usb. But what if it's detected. What should I do? What will I also do if it's not detected. Thanx
Click to expand...
Click to collapse
if it gets detected.. there'll be another question
does it still enter BL (bootloader mode)? haven't been playing with my BA for a long time now, that i have already forgotten how to enter BL mode..
anyway.. if it still enters BL mode.. there may still be a lot of chance reviving it..
AW! i was not able to read the very first post carefully.. you are in the BL or bootloader mode.. to return to normal phone, just reset your device (poke the reset hole at the bottom) or remove the battery, replace it, then hit the power button..
getBL or enterBL is a program that resets your device and lets it enter BL (bootloader) mode.. you need to be in the bootloader mode to be able to flash new/upgrade ROMs..
anyway.. there is a more easier and safer/faster way of flashing roms that does not include the use of the memory card technique.. you only need the USB cable/cradle, your ROM and the RUU (upgrade utility) which will be run on the desktop pc.
where are you located in the phils? maybe i can help you..

WM5->WM6 DSUU MODE Please Wait

I messed up upgrading Atom Exec Life from WM5-6. Middle of process the upgrade stopped. Phone now says !!!Please plug-in the USB cable and reenter the eboot!!! DSUU MODE please Wait...
How do I get phone to see active sync and get OS back to WM5 or upgrade to WM6?

DSU mode died
I have same problem with u....
After that how about your XDA ???
My XDA, after the DSU mode, and when i reseted the XDA, my Xda could not respons anything even the light .....I dont know how to recure itt.....
Please help me .....
Thanks

Diamond doasen't go on in preparing page

Hi
I flashed diamond with a custom rom but it doesn't go in preparing page and i want to flash it again but the computer can't connect to diamond in preparing page
what should i do?

hamid reza said:
Hi
I flashed diamond with a custom rom but it doesn't go in preparing page and i want to flash it again but the computer can't connect to diamond in preparing page
what should i do?
Click to expand...
Click to collapse
...which preparing page? You mean the bootloader?
Do you have an active sync connection?
I don''t have to ask you if you are installed a hard slp?!

in the page that say preparing device for first use
active sync cant connect in the preparing for first use page
yeah olinex1.40

hamid reza said:
in the page that say preparing device for first use
active sync cant connect in the preparing for first use page
yeah olinex1.40
Click to expand...
Click to collapse
...disable the advanved network features: Settings/Connections/USB2PC

I can't go to device it locked in the prepating for first use after flashing rom

ok; make a hard reset!

I made but it locked again in preparing for first use page!

hamid reza said:
I made but it locked again in preparing for first use page!
Click to expand...
Click to collapse
...are you sure you made a hard and not s soft reset?

Yes sure vol down enter then red and then vol up
I just want a way to remove rom or go to spl page directly
How?

hamid reza said:
Yes sure vol down enter then red and then vol up
I just want a way to remove rom or go to spl page directly
How?
Click to expand...
Click to collapse
..you cannot remove a rom by deleting just like a file you know it from the computer world ;-)

Can i go to hard spl page directly?

Plz help i want to go to hard spl page where it shows the information of spl directly
How can i?

hamid reza said:
Plz help i want to go to hard spl page where it shows the information of spl directly
How can i?
Click to expand...
Click to collapse
press volume down and reset button together it will display which hspl you have

press volume down and reset button together it will display which hspl you have
Click to expand...
Click to collapse
tnx
it works

hamid reza said:
tnx
it works
Click to expand...
Click to collapse
no problem you can now connect your usb cable and when it shows at bottom that usb is connected you can reflash the rom

Stuck and boot problems

My phone get's stuck a lot for some reason also when my ram is on like 60 %.
When i reset my phone it automaticly does a hard reset.
I have brought it to a phone store and the guy said he repaired it but it's still broken.
does anybody have the same problem and a idea how to repair it?
HSPL: 1.40.OliNex
Radio: v1.00.25.05
I got the same problem with every ROM I install

TomMyH1992 said:
My phone get's stuck a lot for some reason also when my ram is on like 60 %.
When i reset my phone it automaticly does a hard reset.
I have brought it to a phone store and the guy said he repaired it but it's still broken.
does anybody have the same problem and a idea how to repair it?
HSPL: 1.40.OliNex
Radio: v1.00.25.05
I got the same problem with every ROM I install
Click to expand...
Click to collapse
like I've said before..
hard reset
install an official rom
hard reset
install your rom
hard reset
bye

fabius88 said:
like I've said before..
hard reset
install an official rom
hard reset
install your rom
hard reset
bye
Click to expand...
Click to collapse
gonna try this
EDIT:
at this moment i am not able to make a activesync connection

ok at his moment i am trying to get a active sync connection my pc detects my phone but windows mobile centre says there is something wrong

TomMyH1992 said:
ok at his moment i am trying to get a active sync connection my pc detects my phone but windows mobile centre says there is something wrong
Click to expand...
Click to collapse
try to delete your device from Windows Mobile Centre, then try again to connect your diamond to pc

read the mtty thread and follow the advice there.

sandervanzijl said:
read the mtty thread and follow the advice there.
Click to expand...
Click to collapse
found it gonna try it now

fabius88 said:
try to delete your device from Windows Mobile Centre, then try again to connect your diamond to pc
Click to expand...
Click to collapse
i tried this but it didn't work

ok i got a active sync connection now but when i try to install a original rom i get this : This Update Help can't be used on your PDA-Phone check the Update help

Bricked/dead SGS,

Hello guys, i have a problem with my sgs .. after downgrade from jv9 to froyo i've got my sgs bricked.. cannot enter do download mode by 3 button combo and by usb jiig is well ( jig is working, checked on sgs2) only thing happening is when i connect it by usb cable to my laptop i getting info the windows cannot find the driver for it and after few seconds is disconnecting.
Any ideas how to get it back to life ?
Thanx.
ps. sorry for my english. Cherrs

What happens when you turn it on normally?
At what screen does it stop?
Can you enter recovery mode?

its totally dead.

Remove the battery, wait a few minutes ( In fact, 30 sec should be alright ) the put it back. Press power button, if you see the phone -- triangle -- pc image, then just remove the battery again, put it back and plug your jig. If you see nothing i'm almost sure your screwed.

Steps:
First Remove your battery and wait 60 seconds
Then put the battery back in
There will be a small hole in the right side of the camera like a soft reset hole
take a paper clip
insert it in the hole and wait 25 seconds while pressing it in
then go into the download mode but the volume down +home button + power button
If the button method doesn't work try using the jig
Now it should work

yaro014 said:
Hello guys, i have a problem with my sgs .. after downgrade from jv9 to froyo i've got my sgs bricked.. cannot enter do download mode by 3 button combo and by usb jiig is well ( jig is working, checked on sgs2) only thing happening is when i connect it by usb cable to my laptop i getting info the windows cannot find the driver for it and after few seconds is disconnecting.
Click to expand...
Click to collapse
Can you try running USBDeview from http://www.nirsoft.net/utils/usb_devices_view.html . You should see all your existing devices like mouse, keyboard etc. Then plug the phone in, and if it shows up in USBDeview tell me what it says in these columns for the phone device:
VendorID, ProductID, USB Class, USB SubClass
You may need a couple of tries to get all the numbers if it's disconnecting after a few seconds.
I'm interested because it could be the type of brick we are trying to fix in this thread where the bootloaders have been corrupted and it is going into processor recovery mode. We don't have a fix for you but if I'm right it will confirm that you need to get the phone reflashed by Samsung. Ask them how they do it while you're there.

hmm i cannot see any hole on the right side of the camera.. there is only connector looks like gps antenna.
i tried on 3 different batteries and i tried to take battery out for few minutes and still not work..

hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?

yaro014 said:
hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?
Click to expand...
Click to collapse
Just say to them i was updating my phones software via kies and my pc crashed because of some other application so it got interrupted in the half way now i can boot into my phone.

do you think they will accept it ? i mean .. if they will fix it and say this is my fault then i'll need to pay for this fix ?
anyone guys has experience with it ? how long it takes ?

yaro014 said:
hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?
Click to expand...
Click to collapse
Yes, they won't be able to tell what caused it, though your custom firmware could all reappear if they only reflash the bootloaders. But at least your phone will be fixed.

hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100

yaro014 said:
hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
Try reinstalling the USB drivers from my signature.

yaro014 said:
hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
The brand market can see if u rooted the phone,
But i i also got this kind of brick, when i instaled a 9000m modem to my int i9000,
what i did i heated the phone, this is not a joke, a heated the phone used adb to enter download mode and i flashed stock 2.2 from samfirmware.com
The phone newer worked well so my provider changed the phone and didn't saw that i root it.
try adb and heating than the 3button combo.
good luck

yaro014 said:
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
Yep, that confirms that your initial bootloader is trashed and the CPU has gone into USB recovery mode because it couldn't load the bootloader. The only fix currently is to get Samsung to reflash it, or get someone with a Riffbox or other JTAG equipment to fix it. Heating the phone will not help you, neither will reinstalling Samsung phone USB drivers.

yaro014 said:
hmm i cannot see any hole on the right side of the camera.. there is only connector looks like gps antenna.
i tried on 3 different batteries and i tried to take battery out for few minutes and still not work..
Click to expand...
Click to collapse
Well mate; if we are talking about the usual samsung galaxy s , when we open the lid there definitely is that small gutter with a hole in it . That little diaphragm can be pressed by a blunt pin.

Your provider should fix the phone no problem.
Sent from i9000m on cm7, with xda premium.

Try JIG it help me.
At marktplaats ( EBAY??) you can buy an usb device to help you it works great.
Search te forum "Samsung i9000 galaxy S micro USB download mode Jig"
http://forum.xda-developers.com/showthread.php?t=819551
http://cell-phones.shop.ebay.com/Ce...SB+JIG&_catref=1&_fln=1&_trksid=p3286.c0.m282