Dell Axim x51V - Upgrading, Modifying and Unlocking

Hey Guys,
I have recently bought an Axim x51v and want to upgrade it to WM6, hoever my problem is this, i doenload the chosen new rom which in this case will now be Football's WM6.1 A08 rom, but when i do the restart the bootloader doesent load? so my question is this:
1. Am i doing it correctly - Power + Wifi + Reset button in the back with the stylus then release wifi?
2. If not how is it done,
3. Would i have needed to install the bootloader previously? if so how is this done?
4. Can any of this be done via USB from my PC?
Many thanks for any help on this i am rather anewbie, i previously used an updated rom to update my Orange SPV M3100 (HTC Hermes) which if i remember came with its own PC based flashing utility which made life loads easier.
Any help would be great!
Cheers

bunoire14 said:
Hey Guys,
I have recently bought an Axim x51v and want to upgrade it to WM6, hoever my problem is this, i doenload the chosen new rom which in this case will now be Football's WM6.1 A08 rom, but when i do the restart the bootloader doesent load? so my question is this:
1. Am i doing it correctly - Power + Wifi + Reset button in the back with the stylus then release wifi?
2. If not how is it done,
3. Would i have needed to install the bootloader previously? if so how is this done?
4. Can any of this be done via USB from my PC?
Many thanks for any help on this i am rather anewbie, i previously used an updated rom to update my Orange SPV M3100 (HTC Hermes) which if i remember came with its own PC based flashing utility which made life loads easier.
Any help would be great!
Cheers
Click to expand...
Click to collapse
Here is what you need to do:
1. You need to format an SD card with 32bit file system.
2. You copy the image and its .CRC in that SD card.
3. You put the SD card in your Axim.
4. You press simulatanously the WiFi+Power+reset.
5. You let go the stylus from the reset once you see the bootloader message.
6. It will take some time to load then it will ask you press the Action key.(the middle one).
7. It will again take some time to flash your Axim. Do not power off or intrupt the process otherwise you will kill your Axim.
8. After completing the flashing process it will ask to hard reset (i.e reset+Power).
REMEMBER: Flashing your Axim will void your warranty. Think twice if you still have an extended warranty.
Hope everything goes well.

Bootloader
Hey thanks for the reply i tried your method however dont get a bootloader message? the screen just stay black , i prob sat for about 10 mins waiting then when i release the buttons it just comes up with the restore factory settings screen?
any ideas?
Many thanks,
P.s. not sure if it makes a difference but im still running the default version of WM5 which was shipped with the device, it hasent been previously flashed (to my knowledge).

I believe you dont hold onto the wifi + power + reset all the time. Try holding the wifi + power first, then push reset and let go of it. Wait until the bootloader come up and then release the other 2. Its been a while since I flash so not really sure but I believe thats the way to do it.

Try this little YouTube video. Is it the exact same procedure with your x51v !

Ah Brilliant it worked, wireless and power, then just press the reset in once and it went straight in!
Many thanks for this guys!

Related

Unable to boot up after upgrade ROM to WM6

I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.
Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!
yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.
Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....
Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks
Error message I recive at the 3% stage when using the German ROM and english update util.
use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112
Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?
motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.
I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.
What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.
So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!
ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks
unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help
Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted
Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0

Did I Brick My Phone?

Ok I've flashed close to a dozen times using various great ROMS everyone has provided and never had a problem. Today I realized that ATT/HTC released their official ROM yesterday and I thought I would give it a try. I followed their instructions but it did not work.
My phone looked as though it was updating and it got stuck at 11%. Followed the instructions to recover and it still did not work. Now my phone is stuck at the Triple Color Bar screen and I cannot do anything.
Did I brick my phone?
Can I use some of the options to try to unbrick in the xda wiki?
Thank you in advance.
- Monty
Have you tried flashing a different rom or using a different pc to flash with?
i managed to revive mine from that state the key is getting the usb to let you update again dont plug in the cable until after the ruu is looking for the connection might take a couple tries but that worked for me.
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
MontyV77 said:
Ok I've flashed close to a dozen times using various great ROMS everyone has provided and never had a problem. Today I realized that ATT/HTC released their official ROM yesterday and I thought I would give it a try. I followed their instructions but it did not work.
My phone looked as though it was updating and it got stuck at 11%. Followed the instructions to recover and it still did not work. Now my phone is stuck at the Triple Color Bar screen and I cannot do anything.
Did I brick my phone?
Can I use some of the options to try to unbrick in the xda wiki?
Thank you in advance.
- Monty
Click to expand...
Click to collapse
You should not update using the Oficial ROM release Update because you put in the boot loader from here (Hard-SPL-V7) and it will try over righting the entire rom if you do and is probably what messed up your update attempt. Use Dutty's NBH tool and just decompile the NBH of the official rom, then recompile the windows, splash screens and radio into a new NBH then flash using the RUUwrapper from this site to flash the phone.
TooSharp said:
Have you tried flashing a different rom or using a different pc to flash with?
Click to expand...
Click to collapse
Yes I've tried two different Official ATT ROMs and on different computers but same problem. Actually the only one that will attempt to start loading are the ATT ROMs and none of the cooked ROMs here are loading. Maybe that has something to do with the way they are packaged.
Jefem24 said:
i managed to revive mine from that state the key is getting the usb to let you update again dont plug in the cable until after the ruu is looking for the connection might take a couple tries but that worked for me.
Click to expand...
Click to collapse
Yeah I've done this now over a dozen times since yesterday and still no luck.
duke_stix said:
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
Click to expand...
Click to collapse
This looked the most promising maybe because it felt like I was doing something and I was using the ATT ROM again to update, and it actually started updating again. But it stopped at 11% again and gave me the 262 error.
Below pulled from readme.txt file.
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
Click to expand...
Click to collapse
Tried to soft-reset and reinstall but same problem.
Scrambler001 said:
You should not update using the Oficial ROM release Update because you put in the boot loader from here (Hard-SPL-V7) and it will try over righting the entire rom if you do and is probably what messed up your update attempt. Use Dutty's NBH tool and just decompile the NBH of the official rom, then recompile the windows, splash screens and radio into a new NBH then flash using the RUUwrapper from this site to flash the phone.
Click to expand...
Click to collapse
Haven't yet tried this because I am having a hard time getting details on this. I've been searching looking for "duttythroy nbh tool", "nbh tool", "dutty nbh tool", and "dutty's nbh tool" and I can't find it.
If this helps anyone this is what I have on my tri-color screen:
HERM100
IPL - 1.04
HERM100
SPL - 2.03
Click to expand...
Click to collapse
You can also try to flash from the SD card:
- format a SD card with FAT32
- extract the .NBH file from the rom image you like (for your device of course)
- rename the .NBH to HERMIMG.NBH and copy it to your SD card
- put SD card in phone and start it in bootloader (hold OK button on left side and POWER button at same time and stick with stylus in RESET on bottom)
- confirm flashing on screen
- flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes.
This also works for normal (non preproduction) devices but keep in mind that if the CID does not match the flashing might not work. - this was taken from one old thread
- notes - you should backup everything on your SD card to your PC (because except for HERMIMG.NBH it should be blank)
- you can not get USB related error because it loads from a card
- if you flash official ROM you flash it with everything - radio ROM, Windows and bootloader
I am not really sure about bootloader you should have but for official upgrade official bootloader should be ok (it is first thing to be flashed - so I think you have bootloader from ATT ROM already.
Hope it can help somehow...
hey, what is your spl version?
it should say on your bootloader mode
and then read this http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
that really helps a lot, it has the solution and stuff. hope you unbrick your phone! all i did was download the update and it reloaded to wm5 update on my 8525 then after that, i went for olipro's 2.10 so i dont unbrick it anymore =) then flash all you want!
oh yea the factory update for my 8525 that unbricked my phone was this http://www.htcamerica.net/support/8525/software-downloads.html
try loading that in your phone =)
Ok that was the oddest thing but it worked. I've been trying to possibly unzip some of the packages by way of what duke_stix instructed. My last ROM was Schaps most recent 4.0. I unzipped what he had and ran the RUU file. What was funny though is that it started updating up to 3% then gave me the 260 error but this time my phone restarted and booted back up. I don't know what happen but it works now. If this is suppose to go in as a fix I don't know what happen.
Thank you everyone for all your help. I want to reflash my ROM but I will wait until I see this working for a while.
- Monty
asianr0cker said:
...i went for olipro's 2.10 so i dont unbrick it anymore =) then flash all you want!
Click to expand...
Click to collapse
How do I change my SPL to 2.10 now?
Here is nice tutorial how to flash HardSPL v7 (a.k.a. bootloader 2.10 Olipro). Glad to see you are out of brickland
KarhU said:
Here is nice tutorial how to flash HardSPL v7 (a.k.a. bootloader 2.10 Olipro). Glad to see you are out of brickland
Click to expand...
Click to collapse
Thank you just finished flashing it. Thanks again to all that helped.
MontyV77 said:
How do I change my SPL to 2.10 now?
Click to expand...
Click to collapse
See mrvanx.org
... Edit: That's what you get for waiting 10 minutes before posting. Doh!
Thank You So Much !
I did all pricedures and it worked perfectly. You are the best dude!
duke_stix said:
Hi
Try this:
1) Turn your phone off completely
2) Hold the side OK button and the power button, at the same time push the reset button at the bottom with your stylus.
3) this should get you into the bootloader (the three colour screen)(dont be lazy and just let it load into the bootloader, actually run the key sequence ive just mentioned!)
4) on your PC run the update, i would reccomend the latest official update for your handset, BUT, do the following:
a) Make sure you have WinRAR installed
b) Right click on the update file you have just downloaded
c) 'Extract' the update file to the folder it makes
d) within that folder should be ANOTHER executable file that has the same icon as the original update
e) Extract this file again
f) open the folder it makes and within that there should be a RUUSIGNED.NBH and also the RUU utility itself
5) Run the update utility in the second folder
6) once the utility has loaded, plug your phone in (the text will change from 'SERIAL' to 'USB')
7) proceed with the update and see what happens
hope that helps
good luck.
Click to expand...
Click to collapse
if its an official rom you may need to hard sol it first as i had the same problem updating to original after a chefs special
blowfeld said:
if its an official rom you may need to hard sol it first as i had the same problem updating to original after a chefs special
Click to expand...
Click to collapse
what is a hard sol and how do I do it? I wanna go back to the OEM Official ROM to see if it fixes my no service phone problems.
Ok, I've tried everything that was posted in this thread and nothing worked so far.
My last setup before trying to reinstall the Radio is:
AT&T 8525 (location - Hawaii)
Black Majik's WM6
Herm Radio 1.43.00.00
Hard SPL-V7
The OS has been working great until this previous Monday. Also just in case if this is any relevant, Hawaii has just recently upgraded and turned on it's 3G network just a couple of weeks ago. They are still tweaking the whole thing to make sure all is well. Unfortunately it seems that something they did this past Monday seemed to really screw up the 8525's.
The reason I'm trying to reinstall my radio is because I happened to go to the phone settings, and saw that there was no Radio version on the screen. Thought this might also add to the problem.
Well where I'm at now is that I'm stuck at the Tri-Color loader screen. I've read the Wiki regarding fixing a bricked phone. Doesn't seem to help.
So I'm now stuck and need expertise of more knowledgeable members who might have been in the same situation as me.
Please, really need help as this is a company phone and I've got to get it working cause I don't wanna have to pay for it.

O2 XDA Orbit - Upgrading/Backup/Flashing

Sorry if the post has already been mentioned in another forum before.
I have an O2 XDA Orbit and i'm looking to put Fracoons Artermis rom on it http://forum.xda-developers.com/show...o♦.
I'm pretty new to flashing phones and PDA's but i'm quite experienced with a PC so shouldnt need to much help!
I was wondering what steps I should ensure to take to make sure that I dont turn it into a brick, I could do with a complete guide! I've also been told that i'll need to run the Artermus USPL program after connecting the phone. But any help and advice would be a great help. Is there anyway to backup the phone in the state it is at present if or if it doesnt go wrong?
Thankyou for the help and sorry again i've this has already been asked by someone else! Will really appreciated it!
There is no assurance that the process will not make your device a brick. But it happens only on a rare case. Many 1000s of users have upgraded without problems however a few has got their devices a brick.
There is no point taking a backup as the new ROM will give you different files. Anyway, to make sure you don't end up with a bricked device:
-Charge your device fully
-Run USPL
-The process should complete successfully!
-Upgrade ROM.
-Never disconnect your Pocket PC or turn of your PC when the upgrade is going on.
-If your stuck anywhere, don't try to do anything stupid but come here and post.
-Your device should be fine
-Even if some devices get bricked during one of the upgrade process, there is still a high chance of bringing your device back to good working condition with the help of a Factory ROM and so don't worry and go ahead.
Regards,
Carty..
that's my biggest concern so far... my XDA II SHOULD be able to run WM5 but i'm very concerned that i could turn it into a brick... the reason for this is: the XDA is the only phone i have at the moment.
If it bricks, then i'm literally screwed... i have the HimaUpgrade File that does not need an ID, and as i'm pretty fluent with English, i see no problem in using an English ROM.
The Wiki is a good place to start... but i still don't know if i REALLY need active sync to be running or not, since i cannot understand what good that would do if the device is in Bootloader Mode anyway.
Reason for this is that sometimes i read "Active Sync should be on" and sometimes i read the complete opposite... it's freaking me out.
Device should be Synchronized always for the best choice. All un-official ROMs will require this. However, factory ROMs can be flashed directly from Bootloader mode.
That is why I said when you think you screwed the process of upgrading, mostly your device will be stuck at bootloader or you can access bootloader screen and only a factory rom can go from here.
PS: I wont guarantee if the above will be true on all conditions.
Regards,
Carty..
I flash all my ROMs in bootloader mode, including my own, so it's not restricted to the official ROMs. But you need a working ROM to get it back alive.
I'd recommend using a laptop for flashing or use a USV. If some guys cut your power your computer would crash right in the middle of the flashing process - won't happen on a laptop with a working battery.
This is what I want to know. How do I flash in bootloader mode?
okay, i did it this way: first of all you need a rom to flash your device with, but i guess that should be clear
To put your device into Bootloader Mode you have to press the On/Off Button, the Directional Pad AND the reset button (mostly at the lower left corner) simultaneously.
Release the Reset Button first after about a second, and then the other two Buttons.
Your Device should say "Serial" on its Screen... by that time you can put your Device in the Cradle or connect it via a USB Datacable to your PC.
Also: connect the Cable/Cradle directly to your PC, not to a hub as that could cause Problems during the Flashing Process.
Now you can start the Flash-Program, wait approximately 30 Minutes (if you are just flashing the ROM and nothing else) and follow the Instructions that came with your ROM WORD FOR WORD as these instructions are working for most people.
I'm not saying that flashing is without Problems though... when i flashed my XDA II with WM2005 yesterday, i was not able to send/receive Textmessages (SMS), so i had to reflash the device again with the last ROM released by O2, which sucks.

need hellp pls

I just flash my Artemis with wm6.5 lite made by thormdac, and it does not start, is stuck when WM is loading, I can not connect it to computer, what can I do? Can I make it longer work? I will post some pic with it.
Thank you.
1. have you tried a hard reset? (see wiki to know how to do this)
2. First boot after flash is normaly taking much longer dan a normal boot, ingore all noises (beep) till the screencalibration is visible and input is required,
3. How did you flash, did you remove correctly your microsd card before the flashing/update?
4. Did you use USPL to unlock the current rom first?
If dont work your phone after the steps what Twiggerdingo wrote, you can enter to boot loader with voice + power button (use them at the same time when your phone is off) and connect to PC and flash the latest official rom. After that, flash the uspl and you can flash thormdac's rom.
Twiggerdingo said:
1. have you tried a hard reset? (see wiki to know how to do this)
2. First boot after flash is normaly taking much longer dan a normal boot, ingore all noises (beep) till the screencalibration is visible and input is required,
3. How did you flash, did you remove correctly your microsd card before the flashing/update?
4. Did you use USPL to unlock the current rom first?
Click to expand...
Click to collapse
thanks for the advice, I tried everything you said and not working, thank you
Shady313 said:
If dont work your phone after the steps what Twiggerdingo wrote, you can enter to boot loader with voice + power button (use them at the same time when your phone is off) and connect to PC and flash the latest official rom. After that, flash the uspl and you can flash thormdac's rom.
Click to expand...
Click to collapse
Thank you, that is working.
Ha advice from the master himself did the trick. I am glad it works again!
HTC p3300 Artemis100
Hi Members...
Having HTC p3300 Artemis100 with:
IPL:3.07.0001
SPL:3.07.0000
GSM:02.69.90
OS:3.7.0.0
When Starting its Htc Spash Screen. than error:
"Device Startup Failed Due To Sudden lose of Power
press "YES" To continue
after clicking phone goes off
well i tried to reset phone, hard reset. also changed the bettery but still same problem..
is there any way recover or HARD SPL In Bootloader Mode?
Bcoz I cant Use USPL_Atremis Bcoz Phone dont start...
thanks in advance

[Q] Resetting Defy to "factory"

Hey ppl.
I have a big problem, hope you can help me solve it.
I installed jboogies blurless ginger Froyo build 4 a while ago and everything worked fine. Now the gps module and the loudspeaker is broken and id like to send it in. I guess my guarantee is kinda gone when i sent it in with the modified ROM.
Is there any way to get the old bootloader and the normal Blurish Android?
Please help me.
Thanks in advance!
First, you need:
Original SBF of your country, seek for it here: http://forum.xda-developers.com/showthread.php?t=966537
RSD Lite + Moto Drivers: http://forum.xda-developers.com/showthread.php?t=1100585
Then, once you've got everything, power off you phone. You must enter into recovery mode: press volume down and keep pressing it, press power button. Wait for android robot to appear, then press both volume keys and select "Wipe data/factory reset".
Reboot your phone, this time by holding volume up button. Connect phone via usb to pc ( wait for pc to recognize device ), open rsd lite and flash your downloaded sbf.
i am still running the original factory settings + android update, is there a way to save the original factory settings before i try a new rom? sorry i am in a hurry so did not have much time to search the forum first, and as its along the same lines as the first poster i figured it would be a good place to ask a similar question and expand the thread rather then creating a new one
install cwm and make a nandroid backup of your system then search for a fixed sbf of your current software..as long as you have both of them you should be good to go.
Ty for the help one more what do i look at on my phone so i know im getting the right sbf?
at a guess you need t-mob 2.2 us rom
thanks much appreciated.

Categories

Resources