Develop Bugs

My Cingular 8525 just went dead!!!!

OK!!!
I need some help here.
I was talking on my phone, and it all of a sudden went dead.
Thinking it was a battery problem, i immediately plugged in my wall charger and saw that the light indicator was not lite.
I then got another battery from my functioning 8525, and nothing.
But the functioning phone worked after battery switch. So i ruled out dead battery as a cause.
I only did a ROM upgrade two days ago, otherwise the phone functioned without any problems.
I'll try to keep the phone on wall charger to see maybe it'll help but i doubt it.
Anyone else have this type of problem.
I'm currently thinking that it's dead, but i don't understand what could have happened.

Have you tried a Hard Reset?

I did soft reset, and even attempted to do a hardreset. several times. nothing. I see purely a blank screen.
What worries me is that when i plug in the wall charger i do not see any of the green or orange lights turn on.
I'm trying to search if there is any way for me to have someone check the phone out?
If the cost of fixing the phone is any where near 200 dollars then i might as well just buy another phone. Something better.
But any advice i'm willing to try short of dropping it off a roof. caz i know then i'll for sure have a dead phone...

Aren't there ideas like taking battery out and plugging into computer, and stuff like that?
I think I read them somewhere on the xda wiki.

IMO.. you should call at&t tech. they will most likely replace it.. and since they cant turrn it on.. they wont know what you did. anyway its a warranty exchange.. but im not sure of the number for at&t's tech department. good luck and keep us posted

I had the same probs 2 months ago...
No lights when charger was connected, hard/soft reset didnt help at all.
After 5 days of trying and trying i brought it to my provider repair center.
After 1 month of waiting they said it was a level 3 problem (highest). In the first case i was ordered to pay 230 Euro but i didnt agree, 3 days later they agree with no cost and i got a new tytn.
I used XCPUScalar.2007.v3.01 and clocked till 500 mhz.. maybe it burned my cpu..
Well good luck!

kparikh82276 said:
OK!!!
I need some help here.
I was talking on my phone, and it all of a sudden went dead.
Thinking it was a battery problem, i immediately plugged in my wall charger and saw that the light indicator was not lite.
I then got another battery from my functioning 8525, and nothing.
But the functioning phone worked after battery switch. So i ruled out dead battery as a cause.
I only did a ROM upgrade two days ago, otherwise the phone functioned without any problems.
I'll try to keep the phone on wall charger to see maybe it'll help but i doubt it.
Anyone else have this type of problem.
I'm currently thinking that it's dead, but i don't understand what could have happened.
Click to expand...
Click to collapse
Now I know why you're not successful at flashing your device with my ROM . Sorry that I misunderstood your message.
You have to send it back for repair.
Sorry, again.

How does that happen?
m0nkm0nk said:
I had the same probs 2 months ago...
No lights when charger was connected, hard/soft reset didnt help at all.
After 5 days of trying and trying i brought it to my provider repair center.
After 1 month of waiting they said it was a level 3 problem (highest). In the first case i was ordered to pay 230 Euro but i didnt agree, 3 days later they agree with no cost and i got a new tytn.
I used XCPUScalar.2007.v3.01 and clocked till 500 mhz.. maybe it burned my cpu..
Well good luck!
Click to expand...
Click to collapse
So maybe i might have over clocked my cpu?
I don't know what could have happened.
I do know i installed Schap's 3.60a ROM but i installed it both of my 8525.
So i don't think it was the ROM upgrade that could have caused it.
In the mean time I'm looking into if HTC can help me here. I don't know how this would work.
I purchased this phone unlocked on ebay, i've asked the seller if he/she can get me the original invoice to prove that the phone is under manufacturers warranty.
I'll see.
As far as AT&T is concerned, i don't know how i should approach them.
But once i get the invoice information I'll be able to do more.

In your case contact HTC, forget about AT&T especially if the phone isn't on your account. You may need to be peristent with HTC as although they prefer to do things via the carriers, there's a direct route as well. They track the warranty status by S/N.
Good luck... that sucks.

Thanks for all the support
This morning, i tried to call up my carrier.
I explained to them what i observed and how the phone just went dead.
I did not mention anything about ROM upgrades (though i was asked if i did anything to the phone) nor did i drop it or dung it in water.
I was fortunate, that the lady was nice and understanding. I was surprised to know that they have all the information based on the IMEI number.
So as it turns out i made the purchase off the internet, in june. According to the lady since i made the purchase in june i was still under warrenty. They would ship out a replacement phone.
So far this is looking good.
I didn't expect it, but i guess AT&T isn't as bad as i proclaim it to be.
But customer service and phone service are two different things.
AT&T customer service has always been nice.
But their call service and internet sucks.
But got the contract so gotta stick w/ them.
ANd i like GSM, and Tmobile really sucks here in NJ and NYC.
So i gotta stick w/ AT&T
Will follow up once i get the replacement.
So far in doing business w/ At&T - they know, so don't try to kid them. Also need not give out more information then they ask. Just answer questions simple and to the point w/a bit of humor.

Compact IV Frozen on T-Mobile Splash Screen - HELP

Anyone able to assist. I have searched the forum.
After my compact froze I did a soft reset only to see it hang on the T-Mobile splash screen (white background, pink dots). The ROM details do not even appear in the bottom right hand corner.
I have upgraded my ROM with Hard-SPL, a Radio ROM and Dutty's 1.8 ROM but that was weeks ago.
Not even a Hard-Reset sorts it out.
Cannot see how the new ROM would be causing the problem as it has worked for a few weeks.
Luckily followed all the instructions and have 1.40 Olinex Hard-SPL on the phone. Just need to wait for home so I can plug it into my laptop. What I do from that point on will be the subject of a further search of this board later.
Any assistance?

Since you already have Hard-SPL, try first flashing a stock ROM.
See here for available ROM's: http://wiki.xda-developers.com/index.php?pagename=Diamond_Upgrades
Let us know what the results are...

Thanks for the reply.
Unfortunately I cannot get my Compact to sync with my PC in order to add a stock ROM. As I am frozen on the T-Mobile screen the Mobile Device Center does not connect to the Compacy.
Are there any work arounds?

Oh well back it goes to T-Mobile with the hope that they do not identify that the ROM has changed.

Happened to me before as well.
Start your Phone in bootloader mode. Means you hold down the Volume down button while soft resetting. Then you get to the red, green, blue, white screen. In the bottom it says "serial". once you connect to the PC it switches to "usb" and now you can flash ANY ROM you like. I replaced mine with the same ROM I had before....
Don't know what happened to cause this problem. But I got it solved that way.
Let me know if this worked....

Cheers for the reply Staty.
I was able to get the USB connection to work but after reloading the ROM the phone has gone off and stayed off. Can't get any splash screen now.

But you were able to completely reflash the ROM?
Or did it stop along the way?

Did not stop along the way. Went to 100% and was met by the finished screen on the PC. However the Compact does not turn in now.

So you try to turn it on but nothing happens?
Did you try hooking the phone to the loading cable and then turn it on? Maybe a problem with the bettery?
Besides that I got no idea right now.
Which ROM did you reflash? The same you used before?

Hi,
You must download full rom (with radio etc.), the best original. Doesn't matter which one. And hard reset after that.

staty said:
So you try to turn it on but nothing happens?
Did you try hooking the phone to the loading cable and then turn it on? Maybe a problem with the bettery?
Besides that I got no idea right now.
Which ROM did you reflash? The same you used before?
Click to expand...
Click to collapse
Tried hooking it up to the loading cable, the charger and still no luck.
Have no idea why it will not start-up. Do not even get the white circular light when plugged into the charger.

PanNet said:
Hi,
You must download full rom (with radio etc.), the best original. Doesn't matter which one. And hard reset after that.
Click to expand...
Click to collapse
Yep done all that. Compact still dead. Changed ROM about 3 weeks ago, no problems just stopped working altogether. Was able to connect it to the PC to update ROM again but now nothing.
Not sure how having Hard-SPL on the phone is gonna help when the thing wont turn on.

waynespa said:
Anyone able to assist. I have searched the forum.
After my compact froze I did a soft reset only to see it hang on the T-Mobile splash screen (white background, pink dots). The ROM details do not even appear in the bottom right hand corner.
I have upgraded my ROM with Hard-SPL, a Radio ROM and Dutty's 1.8 ROM but that was weeks ago.
Not even a Hard-Reset sorts it out.
Cannot see how the new ROM would be causing the problem as it has worked for a few weeks.
Luckily followed all the instructions and have 1.40 Olinex Hard-SPL on the phone. Just need to wait for home so I can plug it into my laptop. What I do from that point on will be the subject of a further search of this board later.
Any assistance?
Click to expand...
Click to collapse
Here wot fella.... Yesterday i called t-mobile cause my mda was running kinda hot for some reason, With no effort the lady said it shouldn't be getting that hot (like she could feel the heat over the phone lol) "i'm going to send you a replacement for tomorrow morning" Today, So me thinking a refurbished phone and no screen protector, i asked if they could send me a screen protector, No she said, i'm sending you a brand new phone "in the box" so all the bits will be there.......
Brilliant i get a new mobile..... Here is the best bit....
UPS turns up this morning with a brand new phone.. the guy asks me for the old phone ONLY, didn't take back old batt, headset...etc put it in a bag and away he went......
So i get a brand new phone (BOXED) and get to keep all the old accessories.
So the moral of the story is..... RMA your mobile, tell t-mobile its over heating and pray too god you get the same woman on the phone that i did...!

P.s..... Out of curiosity, Which cooked rom was you using...!

fyew-jit-tiv said:
P.s..... Out of curiosity, Which cooked rom was you using...!
Click to expand...
Click to collapse
I used Dutty's 1.8, but It is not a problem with the ROM, I'm sure of that.

fyew-jit-tiv said:
Here wot fella.... Yesterday i called t-mobile cause my mda was running kinda hot for some reason, With no effort the lady said it shouldn't be getting that hot (like she could feel the heat over the phone lol) "i'm going to send you a replacement for tomorrow morning" Today, So me thinking a refurbished phone and no screen protector, i asked if they could send me a screen protector, No she said, i'm sending you a brand new phone "in the box" so all the bits will be there.......
Brilliant i get a new mobile..... Here is the best bit....
UPS turns up this morning with a brand new phone.. the guy asks me for the old phone ONLY, didn't take back old batt, headset...etc put it in a bag and away he went......
So i get a brand new phone (BOXED) and get to keep all the old accessories.
So the moral of the story is..... RMA your mobile, tell t-mobile its over heating and pray too god you get the same woman on the phone that i did...!
Click to expand...
Click to collapse
Mine has been extremely hot for the last few days. I'm gonna phone them now.

waynespa said:
Yep done all that. Compact still dead. Changed ROM about 3 weeks ago, no problems just stopped working altogether. Was able to connect it to the PC to update ROM again but now nothing.
Not sure how having Hard-SPL on the phone is gonna help when the thing wont turn on.
Click to expand...
Click to collapse
Thats really wiered. Looks like there is more broken than the ROM. Did you try taking out the battery and keeping it out for a little time.
Try to turn on the phone without the battery in it - so all the power in the condensers etc. will be gone.
Keep the battery separated from the phone for a couple hours and then try it again.
I was having the trouble back then, that the more often I tried to turn the phone on while it was broken it turned off itself even quicker. after I left it without touching it an hour it took longer to turn off itself again.

P.P.S and remember so say its the bottom part off the phone or they may try palm you off with its "the battery"...!

fyew-jit-tiv said:
P.P.S and remember so say its the bottom part off the phone or they may try palm you off with its "the battery"...!
Click to expand...
Click to collapse
Called them and put on my nicest charm with a young lady. She actually read out a T-Mobile notice release that said there was a known fault with the phones over-heating during charge and large downloads. It said that customers should be told that it is safe and a software update coming out soon would sort it out.
I told here the phone no longer worked and she said that they would replace but I should keep all accesories and the battery. I said that as it doesn't turn on it could be the battery and she agreed to a FULL replacement.
They are sending it to my work on Monday and will take the old one away.
Thanks for the advice, was really worried they would want it back for testing BEFORE sending out a new one and they may find my Custom ROM
All good though. Thanks again.

staty said:
Thats really wiered. Looks like there is more broken than the ROM. Did you try taking out the battery and keeping it out for a little time.
Try to turn on the phone without the battery in it - so all the power in the condensers etc. will be gone.
Keep the battery separated from the phone for a couple hours and then try it again.
I was having the trouble back then, that the more often I tried to turn the phone on while it was broken it turned off itself even quicker. after I left it without touching it an hour it took longer to turn off itself again.
Click to expand...
Click to collapse
I left the battery overnight but still no luck.
I am pretty certain it'saphone fault now and absolutely nothing to do with ROM's. T-Mobile are now thankfully taking it back.
Cheers

sometime NO GSM and sometime will detect a radio rom.

why my dopod 838pro sometime it cannot detect a radio rom and show a NO GSM, but if detect it a radio rom and it will hang about and half hours and reset will turn back to NO GSM, is hardware or software prob, anyone can give me a solution?

Provide more information - OS version and Radio version. Its probably a hardware problem but you may try to reflash to a manufacturer's shipped version and retest.
I had the same problem basically. Phone would freeze up, get repeated NO GSM messages, drop the radio even when it finds it after several minutes of use. I did buy the phone off eBay used and it did freezeup in WM5 ALOT.
I took the phone apart and cleaned all the contacts - same problems. Reflashed manufacturer's rom again and it took. Before it sometimes would hang up - looking for GSM radio. Took it apart again FULLY and put everything back together. It is now working for the past week. No freezeups or drops. Seems to always find GSM on bootup.

last time using a official rom wm6 also freeze up, then flash it to manila2d rom, it also got a same prob, try reflash a radio rom, but always get stuck at 6%, but try and try then 100% done, but also same prob.
so ur solution is try Reflashed manufacturer's rom again?

Thats what I did but the flash alone didn't fix the problem. I don't think a rom flash will bring your phone back but you may get lucky. I had to open it up and clean and reposition things. For some reason it worked. I still get screen fade to white and the directional pad on the front sometimes doesn't work - you move the scroll wheel and it will work again. Might have to replace the dPad circuit board or flex cable. The HERMES seems to have MAJOR problems with quality control and the radios. I personally think the battery presses against a backing plate which rests directly against the chipsets. The silver plate behind the battery does flex and it shouldn't. It probably should be a little thicker to prevent flexing. The heat from charging and the pressure from the battery I think causes the radios to fail. Bad soldering also may be a problem but any pressure on a motherboard and chipsets isn't a good thing. Also screws that are too tight also may contribute to the problem.
My phone has been working for about a week. Prior to that it was getting constant NO GSM errors on bootup and dropped calls. Today the phone was out of the house for the first time in weeks and it worked without any problems - no freezes (did a lot before) and no dropped radio. It has been sitting on my desk for two weeks without any problem. Will try it a few more days and see.

herm200 no GSM
Hi! I have read all thread about no GSM from here.
I have already do many many tests, tried to flash any radio rom extracted, hard reset, mtty with set 1e 1... I have already dissasemble and reassemble it
but no one fix the problem No GSM.
I have the same probleme, sometime no gsm and sometime ok.
So please, if anyone find everything which can fix this problem please post it!
Sorry for my english!
Thanks a lot for all jobs and helps.

Hello all, my hermes had this problem too!
Sometime it works, " 1.56.70.11" and sometime no! "NO GSM"
i have done about twenty flash thinking it will resolve this problem...
After reading a topic on this problem, i have understand it was an hardware problem. Something unsolde.
I have buy "double face scotch", i have disasemble the phone completely.
And on every chip and on the "battery"( little round and flat) i have put a little piece of scotch. it will do a pression on every chip to keep chip connected on the motherboard.
From this moment, the phone has never freeze, no more "no gsm" message!
ALL IS GOOD
Sorry for my poor english.

Many things can affect the radio
Try this...
Un plug your batt... insert a big piece of aluminium under the batt over the gsm chip... it wil not work properly... Magnetic issues... the batt do this things too i prove it on a Nokia... the batt without the stick = radio problem no signal...
Abd here i got the same trouble no gsm sometimes i realized that has been a lot flashes but noup, was a dialer that makes this issues 3G phone canvas,.... back to touch dialer 3G or 2G and its good now... think the CPROG and some other is not so compatible.

Desperately please help me, my Dopod 838 Pro has No GSM!

hey dude try another rom... the roms with HTC phonecanvas 2g or 3g do this issues on my hermes dunno why... thats th reason i dont cook anymore phoncanvas on my roms.

Update Radio ROM to 1.47
I had same problem just recently, and the recommendation that I got was update your Radio ROM ONLY...I upgrade to Radio 1.47 as all the time I was loosing service connection as well as No GSM...after this, my Hermes took live again.
I had 1.16 Radio...!!! and that issue came up after upgrading to one of the so many cooked ROM...I don't remember which one...
Check this link for more info, it saved my life!!!
http://forum.xda-developers.com/showthread.php?t=295751
Cheers,

[q] super bricked!

I've been rooting and working with custom roms for a long time (couple of years at least). I started with WinMo, and since I got my Evo the day they came out, I've been doing it in Android. I can also use ADB, and can typically recover from pretty much any problem on my Evo. (not claiming to be an expert) HOWEVER...
A couple days ago I loaded the latest Fresh ROM on my phone, and ran out the door while it was loading. Got in my car, the Evo started to reboot after applying the ROM, and zzzZZZIP! The thing went dead. And I mean REAL DEAD. The led which usually shows the charge level as not lit. I pulled the battery and tried to turn it on after replacing it. No go. Nothing when holding down vol while pressing power... nothing. When I got home I tried a wall charger, still no light, no boot, no drive with !, nothing. When the wife got home, tried her Evo's battery... same kind of nothing. USB connection to PC gives no adb access, no fastboot access,... you guessed it, nothing.
Sprint doesn't replace it if you didn't buy the warranty. Called HTC, of course they'll happily replace it, as long as it wasn't rooted. So I have a two part question.
Firstly, because I want my Evo back NOW! No, two days ago! LOL Is there a way to fix it?
Second, if I send it in, is there a way for them to know I rooted it?
Your help would be greatly appreciated.

Have you tried a different battery? That one may be fried. Just a suggestion.
Sent from my PC36100 using XDA App

fdb8231 said:
Have you tried a different battery? That one may be fried. Just a suggestion.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
Thanks for the quick response! Yep, tried that. I thought maybe I had one of the USB port issues that didn't allow me to charge the phone, but alas, my wife's fully charged battery couldn't boot it (or do anything), and my battery worked fine in her Evo.
I also disassembled the phone to check solder connections both on the battery connector and the usb port... both looked totally fine.

Well, if you pay insurance on it you could always accidentally lose it and report it lost or stolen.... that's what I would do, but that's just me....
___________________________________
Yup.... The ones yoe momma told ya about.... Bad Seed Customs!!

Yeah, I'll weigh my options. I think I'll send it to HTC first. I really don't think they can read the internal memory in this condition. I think it is probably fried. It is too late for the Sprint TPE (warranty), but but I might be able to finagle a squaretrade warranty. It will take time though. I thought about having a friend list it in eBay as a buy it now for what a new one costs, buy it from him (he give me my money back), and wait whatever period squaretrade requires, and file a claim. They're great, and I should have bought a squaretrade warranty from day 1. I've had it on the two phones prior and had to use it on one of them. They're easy to deal with and cheaper than any other options. Plus, its more flexible since they don't replace the phone, they issue you a refund for it (which would give me the option of switching phones, not that I would).

mrsato said:
I've been rooting and working with custom roms for a long time (couple of years at least). I started with WinMo, and since I got my Evo the day they came out, I've been doing it in Android. I can also use ADB, and can typically recover from pretty much any problem on my Evo. (not claiming to be an expert) HOWEVER...
A couple days ago I loaded the latest Fresh ROM on my phone, and ran out the door while it was loading. Got in my car, the Evo started to reboot after applying the ROM, and zzzZZZIP! The thing went dead. And I mean REAL DEAD. The led which usually shows the charge level as not lit. I pulled the battery and tried to turn it on after replacing it. No go. Nothing when holding down vol while pressing power... nothing. When I got home I tried a wall charger, still no light, no boot, no drive with !, nothing. When the wife got home, tried her Evo's battery... same kind of nothing. USB connection to PC gives no adb access, no fastboot access,... you guessed it, nothing.
Sprint doesn't replace it if you didn't buy the warranty. Called HTC, of course they'll happily replace it, as long as it wasn't rooted. So I have a two part question.
Firstly, because I want my Evo back NOW! No, two days ago! LOL Is there a way to fix it?
Second, if I send it in, is there a way for them to know I rooted it?
Your help would be greatly appreciated.
Click to expand...
Click to collapse
Are you certain the battery isn't fried? Also, make sure the SD card is fully seated and secure. With the battery OUT, connect your EVO to it's power supply and then reinsert the battery. Sometimes, after doing so, you will see the LED light up. If not, try again. If it still does not, try getting to the Hboot screen by pressing the down volume button while also pressing the power button.

I am pretty sure I tried that. I pulled battery while plugged in, put battery back, no difference. The first thing I thought was that it was a bad battery connection, because the phone has never worked with the battery out, but plugged in. The battery MUST be in to work. So I disassembled it to check the battery and USB connection solder points, and they look fine.
I called a reputable mobile phone tech and he said he has seen this a few times with rooted Android devices. He said he doesn't think they will be able to read the internal memory, or probably won't go through the effort it would require to (pull the internal memory out and put it in a reader).

Just pull all your root files off the SD card cause that is a dead give away that it is rooted.
Sent from my PC36100 using XDA App

Insurance
Going through HTC is going to be a waste of time. Their turn around time is 30 days... And thats if they dont discover the rooting and therefore actually replace it.
Your best bet is sucking it up and paying the $100 deductible for Asurion insurance... If you order on their website www.phoneclaim.com they will overnight for free. However I have heard of it being back-ordered, in which case you will either wait, or be one of the lucky guys who gets a brand new one.
In regards to them seeing your internal memory, I would say its 50/50. They can recover that sort of stuff, but at the same time, HTC is way more lenient with rooting/mods than other manufacturers.
Good luck

toddlmr said:
Just pull all your root files off the SD card cause that is a dead give away that it is rooted.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
As it turns out, when you send your phone to HTC, you have to pull your battery cover, battery, microSD card, and any other "accessories" you have off, and keep them. They only want the phone without any of these items. I asked the guy, "you don't want me to ship the batter OR even the cover with the phone, but separate?" He said, "no, they are yours to keep. if you send them to us, they will not be returned." LOL! If they replace the phone, I'll have spare parts! Yaaay! I left my screen protector on it, in case they can fix it, they won't scratch it. Love my Evo y'all!

Yah the same exact thing happened to me when i first got my evo (the first day it came out). Absolutely no sign of life, but got it through best buy and just went back with no insurance or anything and she gave me another one on the spot.

Yeah if it won't even power, they won't bother. You are straight unless by some miracle they actually get it working.
TEP is a godsend.
I'm supremely surprised no one has popped in to say "WRONG SECTION AMAGADWTFBBQ!"

sekigah84 said:
I'm supremely surprised no one has popped in to say "WRONG SECTION AMAGADWTFBBQ!"
Click to expand...
Click to collapse
That would be so barbaric and elementary - so many capitals and so much hostility!
To the OP:
Wrong section, jackhole.
It will probably cost you $35 without the insurance. If one store doesn't work, try another.

Yeah, just smash it on the floor and claim a new one
$100.00 ..thats it.

Where to post this?
I had a feeling this was the wrong place to post this, but not sure where else to do it. General maybe?
SORRY! ;-P
I wouldn't have a problem if an admin moved it to the right place.

Do did you make a decision to send it in?

teh roxxorz said:
Do did you make a decision to send it in?
Click to expand...
Click to collapse
Yeah, with fingers and toes crossed.

Well, I don't think they'll find out. Cuz I'm in engineering, and they could try to overvolt the phone [in an attempt to turn it on] but too much a risk of frying the circuits. Also no sdcard so they can't see your files...and way too much work to disassemble...so I think you're good.

Thanks man, that really is reassuring. I'm kind of on pins and needles over this. I can't afford ANYTHING, much less to buy another phone (I was laid off Jan 1).
I've been desperately trying to learn to program in Java, for Android. Both should provide me with more flexibility financially. I'd rather work as a contractor than FTE any day, but sysadmin type work is hard to find these days. I didn't expect to enjoy programming as much as I am, which is a pleasant surprise. Java isn't so hard. ;-)
I hope to get my Evo replaced under warranty. Then I hope to get more income by the time the new Evo 3D comes out! Not to sideline this thread, but what do you guys think of that thing? I'm also wondering if the new Evo View 4G would work as a phone replacement, just using Google Voice to replace cell service. Most new cars have bluetooth built in, and otherwise can use a bt headset (even stereo headphone type), so you never have to hold it to your head anyway.

Sorry, I guess I spaced posting my results. The did not know out had been rooted. They just replaced the motherboard and sent out back.
Unfortunately, they downgraded me from hw version 003 to 002. There were also two soft key lights out and I sent it back. Even though I complained about the version difference they still put another v2 in it. I called US public relations and came close to getting a hwy v3 board in but in the end it didn't happen. All they really care is that they made the device work.
Moral of the story is, if your Evo is dead-dead, send it to htc, and now you know what to expect.

[Q] tried flasing rom and phone is dead..

i got a samsung gs3 yesterday, i loved everything but battery life, lastnight i used George Holtz's "towel root" and rooted my phone, added super user and rom toolbox, upgraded my recovery to clockwork mod basic, and proceded to flash to "flashingdroid version 2.2" it went thru everything and installed the rom, when it tried to reboot, it went black... now it does nothing, computer tries to recognize it, abut i cant get it to download mode, and i cant get it into recovery mode... it does not show charge picture when plugged in and if i take the battery out, plug it in, then insert the battery i get a red light... PLEASE HELP!!!!!!!

noobbrokes3 said:
i got a samsung gs3 yesterday, i loved everything but battery life, lastnight i used George Holtz's "towel root" and rooted my phone, added super user and rom toolbox, upgraded my recovery to clockwork mod basic, and proceded to flash to "flashingdroid version 2.2" it went thru everything and installed the rom, when it tried to reboot, it went black... now it does nothing, computer tries to recognize it, abut i cant get it to download mode, and i cant get it into recovery mode... it does not show charge picture when plugged in and if i take the battery out, plug it in, then insert the battery i get a red light... PLEASE HELP!!!!!!!
Click to expand...
Click to collapse
What model is your phone? You flashed a i9300 ROM, this is the sub-forum for the i747.

its the i747, i before looking today never knew there were more than 1 model of the GS3, is it possible to fix it?

This may help:
http://forum.xda-developers.com/showthread.php?t=2549068

audit13 said:
This may help:
http://forum.xda-developers.com/showthread.php?t=2549068
Click to expand...
Click to collapse
my problem is my phone does NOT vibrate when power button is pressed, it isnt doing ANYTHING at ALL, the red charging light only comes on when battery is left out and the phone is plugged in, light turns off after a minute or so of the battery being installed, to me it seems like less rom flash related, and more failure in the board, but im not good at this stuff so im probably wrong, i bought a verizon one (i535) for 50 bucks (pretty banged up touchscreen is cracked in several places i got it without a back cover,but it works,) to get me by but i miss my 4g on straight talk =( i wish i had just left it alone, it was clean just 1 crack in the touch screen wires ans such for lcdanddigitizer got cut by accient while trying to modify midframe for verizon board, i sure as hell cant afford the att version for a while 150-260 for a decent i747, is it possible that a JTAG service would be able to bring it to life or even one of those dongles to force recovery?

noobbrokes3 said:
my problem is my phone does NOT vibrate when power button is pressed, it isnt doing ANYTHING at ALL, the red charging light only comes on when battery is left out and the phone is plugged in, light turns off after a minute or so of the battery being installed, to me it seems like less rom flash related, and more failure in the board, but im not good at this stuff so im probably wrong, i bought a verizon one (i535) for 50 bucks (pretty banged up touchscreen is cracked in several places i got it without a back cover,but it works,) to get me by but i miss my 4g on straight talk =( i wish i had just left it alone, it was clean just 1 crack in the touch screen wires ans such for lcdanddigitizer got cut by accient while trying to modify midframe for verizon board, i sure as hell cant afford the att version for a while 150-260 for a decent i747, is it possible that a JTAG service would be able to bring it to life or even one of those dongles to force recovery?
Click to expand...
Click to collapse
It could be a board failure but it happened right after you flashed the ROM which leads me to believe it is software related.
A dongle is not going to help since the phone won't even power up. A jtag service would be your best and quickest option. You should try and find a shop that will guarantee to revive the phone or you pay nothing.
This might help with your current phone: http://www.xda-developers.com/android/how-to-make-your-verizon-galaxy-s-iii-a-world-phone/

noobbrokes3 said:
my problem is my phone does NOT vibrate when power button is pressed, it isnt doing ANYTHING at ALL, the red charging light only comes on when battery is left out and the phone is plugged in, light turns off after a minute or so of the battery being installed, to me it seems like less rom flash related, and more failure in the board, but im not good at this stuff so im probably wrong, i bought a verizon one (i535) for 50 bucks (pretty banged up touchscreen is cracked in several places i got it without a back cover,but it works,) to get me by but i miss my 4g on straight talk =( i wish i had just left it alone, it was clean just 1 crack in the touch screen wires ans such for lcdanddigitizer got cut by accient while trying to modify midframe for verizon board, i sure as hell cant afford the att version for a while 150-260 for a decent i747, is it possible that a JTAG service would be able to bring it to life or even one of those dongles to force recovery?
Click to expand...
Click to collapse
Flashing an i9300 rom is guaranteed to hard brick the device and cause exactly what you described. If you follow the instructions in the thread linked in an above post it probably has a 90% chance of fixing it.
I am 99% certain it is not a hardware failure. Others have done the exact same thing and were able to fix it by using the instructions in that thread.

audit13 said:
It could be a board failure but it happened right after you flashed the ROM which leads me to believe it is software related.
A dongle is not going to help since the phone won't even power up. A jtag service would be your best and quickest option. You should try and find a shop that will guarantee to revive the phone or you pay nothing.
This might help with your current phone: http://www.xda-developers.com/android/how-to-make-your-verizon-galaxy-s-iii-a-world-phone/
Click to expand...
Click to collapse
i found one on ebay, full refund short of a 5 dollar shipping cost for return shipping, once i have money that i can spend ill sure as hell be giving it a shot

Or you can attempt to fix it for free.....but I suppose that is up to you.

DocHoliday77 said:
Or you can attempt to fix it for free.....but I suppose that is up to you.
Click to expand...
Click to collapse
either way its gonna cost me a little cash, i dont have a 16 gig sd card, forgive me for being so noob but the sd card trick CAN work for my case?? i know for a fact i cant do anythingto my phone right now as it wont even power on, but if you BELIEVE it will work ill gove it a try

Unless you updated with the kk ota, you are probably on 4.3 firmware. I cannot guarantee it will work, but I believe the chances are pretty good that it will.
Just remember, if it doesn't work, dont give up on the first try. Many have had to run through the process several times before it would actually boot up again.
The only other tip I can think to give is to make sure you buy a decent sd card. It doesn't have to be top of the line, but there are tons of fake ones out there that would be less likely to work. If you can, try to buy one from an authorized dealer for whatever brand you are considering. This greatly reduces the chance of getting a bad card.

DocHoliday77 said:
Unless you updated with the kk ota, you are probably on 4.3 firmware. I cannot guarantee it will work, but I believe the chances are pretty good that it will.
Just remember, if it doesn't work, dont give up on the first try. Many have had to run through the process several times before it would actually boot up again.
The only other tip I can think to give is to make sure you buy a decent sd card. It doesn't have to be top of the line, but there are tons of fake ones out there that would be less likely to work. If you can, try to buy one from an authorized dealer for whatever brand you are considering. This greatly reduces the chance of getting a bad card.
Click to expand...
Click to collapse
4.0.x was the last firmware, i never got to update it. i bought a PNY 16gb microSD HC class 4, it was 25 bucks at the local drug store, i was hoping for a class 6 - 10 but i believe it is a good quality card, maybe you would know better?

I won't lie, I am not a big fan of PNY, but as long as its the real thing, I think it should work. Class 6 or better is recommended, but it has worked on class 4 cards too. At this point, the only thing left to do is give it a shot. Good luck!