Related
I just found a Cheinese Rom in the FTP, and using the "MaUpgradeUt_noID" it seems can detect my rom version, but i did not continue because i can not afford to "Fail", DID anyone know how to upgrade my english ROM to chinese???
HELP!!!!!!!!!!!!!!!
ericcc said:
I just found a Cheinese Rom in the FTP, and using the "MaUpgradeUt_noID" it seems can detect my rom version, but i did not continue because i can not afford to "Fail", DID anyone know how to upgrade my english ROM to chinese???
HELP!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
should be no problem for that , you can look at FTP again there had new ROM 11336_11334_10402 that's same as I had Dopod 900 , I already try to flush WEE i-mate ROM and flush back Dopod ROM twice no problem for flush ,
how can you upgrade it? need to enter serial mode? ( how to enter for universal) what tool did you use?
thx
ericcc said:
how can you upgrade it? need to enter serial mode? ( how to enter for universal) what tool did you use?
thx
Click to expand...
Click to collapse
See here maybe help http://wiki.xda-developers.com/index.php?pagename=Universal_Technical
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
There are a few things I did after I upgraded to CHT ROM:
1. Changed the system font to the more artistic Kai font (from KAIU.ttf on a Windows machine). The original system font was MingLiU, which looked kind of scrawny on a VGA screen.
2. Re-enabled ClearType for the system and PIE. For some reason, Dopod disabled ClearType settings so the user cannot turn on ClearType from the user interface. I used a registry editor and modified a few keys to get the ClearType feature back.
With the Kai font and ClearType, the screen becomes a lot more readable and very pretty! If someone is interested in step-by-step instructions, let me know, and I will post them.
By the way, I was so excited when I discovered the im.tv site actually works for me in USA. I was able to watch the TV news in Taiwan in full VGA screen.
One difference I noticed is that with the WWE ROM, I can very easily set up Bluetooth ActiveSync. With the CHT ROM, the device can only discover the serial port service on my computer, but not recognize its ActiveSync capability. If someone knows how to correct this, please let me know.
Also, in case you don't know, the keyboard mappings between WWE and CHT ROMs are slightly different. The SYM key is swapped with the ";" character, probably because SYM is hardly used in Chinese input. The shortcut "FN + ;" can toggle the English and Bomopofo modes. Note the ";" character is now on the SYM key of JASJAR.
yyl said:
There are a few things I did after I upgraded to CHT ROM:
1. Changed the system font to the more artistic Kai font (from KAIU.ttf on a Windows machine). The original system font was MingLiU, which looked kind of scrawny on a VGA screen.
Click to expand...
Click to collapse
Hi yyl :
Can you tell me how to change system front to Kai ?
Thanks
1. Copy KAIU.ttf from a Windows machine. Paste it into the Pocket PC's "Windows" directory thru ActiveSync.
2. Using a registry editor (like PHM RegEdit), BACK UP your registry first! Then go to "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\FontLink\SystemLink\". Change the data of "Courier New" and "Tahoma" keys to "\windows\KAIU.ttf,DFKai-SB".
3. Soft-reset your device. Now all the Chinese characters become Kai font. It is not very smooth, because ClearType is still disabled.
4. To enable ClearType, this is how I did it. Maybe some steps are not really necessary.
5. Using the same registry editor, search for the keyword "cleartype" in all the keys and values. I found three matches. I set ClearType=1, NoClearType=0, ClearTypeText=1 respectively.
6. Soft-reset your device. You will see that the system ClearType is still disabled. Go to "Settings -> System -> Screen -> ClearType" to enable ClearType. This option was originally hidden from end users. Now it's visible. Once you check the "Enable ClearType" box, the font will immediately smooth up.
That's it. One thing worthy of note is, KAIU.ttf seems to only have traditional Chinese characters, not simplied Chinese. I am not sure.
Thanks yyl , I will try it today
yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Can anyone give me more detailed information about how to use MaUpgradeUt_noID.exe? When I run it, I get an error message: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem", any help will be appreciated! I'm trying to update my Jasjar to CHT ROM.
yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."
yyl said:
I did the upgrade from Jasjar WWE to Dopod CHT. Here is how I did it:
1. Connect JJ to ActiveSync thru USB and wait till the sync session is completed.
2. While the sync is still active, I ran MaUpgradeUt_noID.exe. After a few steps of checking, it will disconnect ActiveSync and put the JJ into the bootloader mode.
3. The upgrade will halt with a country code error. No upgrade has been performed yet.
4. Run MaUpgradeUt_noID.exe again while the cable is still connected and JJ still in bootloader mode. I was prompted that I am upgrading from [Blank] to [NewVersionNumber]. Click "Next".
5. The ROM will be upgraded this time till it's done. It took about 20 minutes.
6. I pressed both softkeys and reset. When the reset prompt comes up, I pressed "0" to reset to default factory settings. After some booting time, JJ starts to speak Chinese.
I upgraded to Chinese ROM because the Chinese plug-in I used to use for English ROM is kind of buggy on WM5. Thanks to everyone on this forum.
Click to expand...
Click to collapse
Thanks! I am Upgrading my ROM now, May the God bless me!
Upgrade Success! thx everyone's help!
yyl :
Can you upload KAIU.ttf which I can't find in my window machine, Are you used Chiese window system ? mine was English + language pack
The KAIU.ttf comes with many versions of Microsoft Office of many languages. When the Asian character support is selected during installation, Office will install some extra Asian fonts for you. This is one of them.
Anyway, I uploaded this font to ftp://xdaupload:[email protected]/Universal
I don't know if this upload is appropriate. If it is not, the board moderators, please feel free to delete it. Thanks.
The principles that I outlined above should work with any TrueType Chinese font that you like.
johnney said:
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."
Click to expand...
Click to collapse
Download "(Open_ch)UNI_DOPOD_11336_134_10402_Test.exe" from the "Universal" folder of this site (see the link in my previous post). Use Winzip to extract all the content from this EXE file into a folder on your hard drive. Place "MaUpgradeUt_noID.exe" into the same folder. Then perform the steps I mentioned above.
I have Modify the font to KAIU , But it does not suppurt Simpfy Chinese, it only support tradition chinese, does any font will fit Both?
I did it!
yyl said:
johnney said:
Can you give me more detailed instruction about how to use MaUpgradeUt_noID.exe? Every time I run it, I get an error message as follows: "This application has failed to start because RUU.dll was not found. Re-installing the application may fix this problem."
Click to expand...
Click to collapse
Download "(Open_ch)UNI_DOPOD_11336_134_10402_Test.exe" from the "Universal" folder of this site (see the link in my previous post). Use Winzip to extract all the content from this EXE file into a folder on your hard drive. Place "MaUpgradeUt_noID.exe" into the same folder. Then perform the steps I mentioned above.
Click to expand...
Click to collapse
Thanks for your help! Now I did it! My mistake was that I copyed the whole exe file to the folder!
Do you guys have Wisbar Advance 2 installed? How's it work? It really slowed my system down on my previouse english ROM.
Re: I did it!
johnney said:
Thanks for your help! Now I did it! My mistake was that I copyed the whole exe file to the folder!
Do you guys have Wisbar Advance 2 installed? How's it work? It really slowed my system down on my previouse english ROM.
Click to expand...
Click to collapse
I use Magic Button to "truly" close applications. It also shows battery meter and the icons of currently running apps.
ericcc said:
I have Modify the font to KAIU , But it does not suppurt Simpfy Chinese, it only support tradition chinese, does any font will fit Both?
Click to expand...
Click to collapse
Yes, as I mentioned in one of my previous posts, KAIU.ttf seems to include only traditional Chinese. The MingLiU font that came with the Dopod ROM has both traditional and simplified. I presume there are many third-party fonts on the market that support both. Note that fonts supporting both styles tend to occupy a lot more space.
Well, this is pretty newbie advice to most of you, so you may think it doesn't warrant a write up, but I had to do some searching for info on how to upgrade my ROM so I thought it would be good to put it all in one thread.
1) Download the ROM you want from the FTP server....Details here http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
2) Download MaUpgradeUt_noID.exe to your Desktop from here http://forum.xda-developers.com/download.php?id=7644
3) Disconnect your device from the USB cable.
4) Hold the Power button + Light bulb button, and press the reset pin found at the back of the device (fiddly if you have large fingers).
You will notice that the screen of the device is dark but has “USB” and "v 1.0" written on it.
5) Connect back your device via the USB cable.
6) Run the download ROM upgrade application...When it prompts you to begin the upgrade process, just minimise the window or leave it alone (DON'T CLOSE THE PROGRAM).
7) Whilst it is running, use Windows to search for a file named RUU.dll
8 ) Right click file and choose ‘Open Containing Folder’
9) Select all files and copy them
10) Create a temporary storage location....C:\Upgrade....And Paste all copied files in here.
11) Copy the file MaUpgradeUt_noID.exe from the desktop into C:\Upgrade
12) Close the previously started upgrade application running in the background
13) Run MaUpgradeUt_noID.exe from it's C:\Upgrade location
The upgrade process should begin now…If it does not, run the MaUpgradeUt_noID.exe application again
Make sure you DO NOT DISCONNECT the cable.
The upgrade takes around 20 minutes to complete.
14: Disconnect the USB cable when told, then push the reset pin. Ignore the advice to do a hard reset by holding down the soft keys while you do this, just push the reset pin by itself. Your Universal will load the new ROM image and you're all done.
Thanks.
Thanks!
There is only one thing, step 4, it is not USB but Serial.
Mento said:
Thanks!
There is only one thing, step 4, it is not USB but Serial.
Click to expand...
Click to collapse
It will go to USB when upgrading.
It doesn't seem to work with last Qtek 9000 ROM...
Help!
OK, I made my own instructions. Follow this instruction of mine:
The file is extracted in your computer. Once you run the shipped.exe file, you need to go to:
My Computer
Your Drive (mine is Drive C)
Show the contents of this drive
Documents and Settings
Choose your folder name
Choose "TOOLS" from the menu bar
Choose "FOLDER OPTIONS"
Click on the "VIEW" tab
Click on "HIDDEN FILES AND FOLDERS"
YOU WANT TO SHOW ALL HIDDEN FILES AND FOLDERS
Now go to TEMP folder
Now you will notice a bunch of folders will show up, tons of them to be exact. What you need to do now is click on the shipped.exe file again and "LOOK" for the folder being created because that folder is what you want to copy. If you did not see it created, you have to manually open each folder and look for the files I listed below.
Assuming you found the folder, you will have these following files inside that folder:
ms_.nbf----------------------this file is responsible for EXT ROM Version
nk.nbf------------------------this file is responsible for Windows Mobile Version
radio.nbf---------------------this file is responsible for Radio Version
EnterBL
GetDeviceData
readme
ROMUpgradeUt
RUU.conf
RUU.dll
UI.dll
MaUpgradeUt_noID
If the file MaUpgradeUt_noID is not there. You need to get hold of a copy of this file as you need this.
There you have it, REMEMBER, you need to have the MaUpgradeUt_noID file plus all the rest of the file if you want to upgrade to the ENTIRE I-Mate ROM, QTEK, O2, or whatever ROM you want.
If you only want to upgrade to the radio version then you need to delete 2 files namely: "ms_.nbf" and "nk.nbf". Leave "radio.nbf" alone and click on the "MaUpgradeUt_noID" file to initiate the Radio installation. Basically those 3 files control what you want to update on your device.
Hope my instructions were clear enough for you. Hope this helps.
cannot locate files after running exe
Hi All, I have ran the ROM update exe and the message saying extracting file XXX etc appears OK then the program closes. When I search for the files, for instance *.nbf they dont exist anywhere on the computer - does the exe autodelete the temp directory and have I missed a stage ? Any help gratefully accepted
Re: cannot locate files after running exe
SteveInUK said:
Hi All, I have ran the ROM update exe and the message saying extracting file XXX etc appears OK then the program closes. When I search for the files, for instance *.nbf they dont exist anywhere on the computer - does the exe autodelete the temp directory and have I missed a stage ? Any help gratefully accepted
Click to expand...
Click to collapse
Did you follow the instructions above on how to show hidden files and folders? After double clicking the .exe file and running it, leave it open then look for the NEWLY created folder in the TEMP folder as instructed. You need to look for it the hard way by opening each folder one by one and check for the files to see if you got the right one.
someone advised me for some extra step, someone please advise is it coorect steps:
"Then you need to make a small change to one of the text files. Look in the directory for
RUU.conf
Open it in notepad and add this line
[CHECKCEID_TYPE]=1
then save it
That’s about it….."
thx for reply christian,
yes i tried searching every folder the manual way but still no joy, I have just copied the rom exe onto my other computer and it worked OK on there and updated my exec without any further problems
Hi All, Linked to the update of the exec software , i noticed the audio playback on tom tom navigator and media files is very jerky to the point you can hardly make out what is being said. has anyone else had the same problem and have you found a solution to fix the problem ?
many thanks
Steve
Bricked QTek 9000
I got a Qtek on ebay and it was working when I tried to upgrade it failed with a "115" Radio Error.
Tried the method on this thread and it completes the upgrade but when I reset, I does not change from "USB v1.0" can anyone help!!!!
Hi
I'd like to take the risk for updating my Dopod 900 for new versions of ROM & radio, but I've got couple of questions.
1. I've got Dopod 900. I do understand, that it's absolutely the same with Qtek9000, but to be sure: may I use ROM update for Qtek?
2. My ROM (1.13.69) & radio (1.04.02) as of 10/12/05 are ancient What version of ROM & radio consider to be stable as of now? I saw in signatures that people using ROM 1.30.77 and radio 1.09.00. Are they OK?
3. I got on FTP and was a bit confused: as far as I understood the latest ROM is 1.30.100 (UNI_QTEK_130100_190_10900_ESN_Ship.exe), but it's for ESN (Spanish???) localization. So in order to get WWE I should use UNI_ORUK_13090_174_10300_WWE_Ship.exe and that update radio separately from 1.03.00 up to 1.09.00 or just UNI_QTEK_13077_176_10900_WWE_Ship.exe? What would u advice me?
4. What is the benefit for updating from 1.13.69 and 1.04.02? Will it works faster & more stable?
Thx in advance & take care
Hi
I tried this and get a 120 (incorrect country ID) error.
Strange, my V1640 from Vodafone is spanish and i want to upgrade to UNI_QTEK_130100_190_10900_ESN_Ship.exe
so it should be ok.
Am i wrong? Is there a way to get rid of that message?
Hi I have a Xda Exec
ROM: 1.13.82 WWE
Rom date 11/30/05
Radio 1.04.02
Protocol 42.37.P8
Ext Rom 1.13.188WWE
And when i do this:
4) Hold the Power button + Light bulb button, and press the reset pin found at the back of the device (fiddly if you have large fingers).
The devide says me:
Boot options:
Enable KITL
Clean registry hive
Format storage
I soupouse that it isn´t the boot loader for go on with the proces... what happens?
I want to upgrade to UNI_QTEK_13077_176_10900_WWE_Ship.exe for use my heasphones motorola stereo... (AD2P..)
Can any body help me?
Thanks a lot
Please!!!
Edit post number 1 and add as the last step:
14: Disconnect the USB cable when told, then push the reset pin. Ignore the advice to do a hard reset by holding down the soft keys while you do this, just push the reset pin by itself. Your Universal will load the new ROM image and you're all done.
It seems that a lot of people are having trouble after a ROM upgrade by following the instructions on the upgrade program which tell them to hard reset.
Many thanks! PU10 by German T-Mobile upgraded to WWE
I have a T mobile mda pro, any recommendations as to what the best rom is.
Im torn between the new orange rom which is supposed to be good and the jasjar one?
Anyone?
Latest jasjar ROM
Hi,
Can I follow these instructions with my UK jasjar?
Where can I find the latest Rom?
Cheers
Anyone can point me out to the adequate ROM?
thanks
astpaul said:
Hi
I tried this and get a 120 (incorrect country ID) error.
Strange, my V1640 from Vodafone is spanish and i want to upgrade to UNI_QTEK_130100_190_10900_ESN_Ship.exe
so it should be ok.
Am i wrong? Is there a way to get rid of that message?
Click to expand...
Click to collapse
Okay, I've finally got WM6 on my HX2110. For any other people having the same problems I did, here is exactly what I did. What the guides I've found don't tell you is where to find it, and what to do when you get it. Basically you need to trick the iPaq into thinking it's getting the original 1.00.00.l firmware and then switch firmwares. You need to downgrade to the original H firmware before the iPaq will accept wm6. This worked perfectly for me after two days of trial and error. More detailed steps are below, but basically its: flash with 100l, reset, run 100l and swap firmware with 100h, flash, run 100l and swap with wm6, flash
Prerequisites:
Advanced_pack_for_hx2xxx_to_WM6
iPaq HX2110
USB connection to computer
1) Hard reset iPaq. Do this by holding the calendar button and itask button (curved arrow), and then put your stylus into the reset hole on the bottom of the iPaq. This will hard reset it.
2) After doing that, put it in to bootloader mode. You do this by holding the contact button (to the right of the calendar) and the itask arrow, and then clicking the reset button on the bottom. It should now be in bootloader mode. unplug the power/usb cable and plug it back in. hit the calendar button. it should now say USB.
3) run hpRUU.exe under the Wm5.0 for hx2000_1.00.00.L_ENG folder. It's found in provishki. it will flash your ipaq to 1.00.00.l . let it flash all the way.
4) hard reset the ipaq and put it in bootloader mode. see steps 1 and 2. make sure it says USB.
5) do step 3 again, but this time don't click upgrade. rename the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file to 100l.nbf
6) go into the SP32408_1.00.00.H_ENG folder and get the NBF file from there. copy it into the 1.00.00.L folder that we were just in. rename is to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf. click upgrade. let the upgrade finish.
7) repeat steps 1 and 2.
8) delete the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file that you just copied over and rename the 100l.nbf file to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf.
9) run hpruu.exe again. DO NOT CLICK UPGRADE.
10) get the wm6_wwe.nbf file and copy it into the directory we were just in. rename E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf to 100l.old and wm6_wwe.nbf to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf
11) click upgrade. let it finish.
12) repeat step 1
you should now have Windows Mobile 6 on your iPaq. Good luck
I've been finding things that said I need to downgrade my firmware to 1.00.00.h after doing the 1.00.00.l version. I can't find L for the life of me. All I need is for someone to show me where I can get it. The only sites that bring anything up about that are russian.
jsbarone said:
I've been finding things that said I need to downgrade my firmware to 1.00.00.h after doing the 1.00.00.l version. I can't find L for the life of me. All I need is for someone to show me where I can get it. The only sites that bring anything up about that are russian.
Click to expand...
Click to collapse
Hi jsbarone
You may study and try from this:
http://forum.xda-developers.com/showthread.php?t=330682
hkksl said:
Hi jsbarone
You may study and try from this:
http://forum.xda-developers.com/showthread.php?t=330682
Click to expand...
Click to collapse
More info found here
http://forum.xda-developers.com/showthread.php?t=329079&page=9
updated with my guide on flashing my hx2110. it worked well for me. it's not perfect but hopefully it will help someone with the same problems I had.
Thanks Man you saved my day... everything worked fine!!!
At last, I done an upgrade to WM5 (still waiting for help to understand how to upgrade to WM6)...
May I Ask A question?
Everyone doing an upgrade have a slower PDA?
cant make it work :-(
i did precisely as described in this article, but now i got a "bricked" HX2110.
I only get to the loading screen with the version 5.20.00.H ENG
Someone had an idea??
Thanks!!
//Pzymex
pzymex said:
i did precisely as described in this article, but now i got a "bricked" HX2110.
I only get to the loading screen with the version 5.20.00.H ENG
Someone had an idea??
Thanks!!
//Pzymex
Click to expand...
Click to collapse
The answers are all in the Posts above.
Hkssl:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
pzymex said:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
Click to expand...
Click to collapse
i might find the problem, i think i started with wm2003. do i need any prerequities to upgrade from WM2003 to wm6??
and what to do when I already bricked my hx2110?
something it's not clear for me... When we run hpruu and 100% of instalation it's complete the devive restart it self. Do we have to wait there? wen do we have to do the hard reset?
I did it!
my advices are
1)start installing from windows mobile 2003
2) do not restart the pocket pc before the windows log-in screen appears!
Good luck!
Thanks!
sorry for my english
So many thanks for your tips.
I have some friends who couldn't flash by ordinary steps, I hope your guides will solve their problem on upgrading to my Thai Customized WM6.1.
Cheers,
Keng230
pzymex said:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
Click to expand...
Click to collapse
My device is Original WM2003, are there any prerequities before doing the upgrade mentioned in this article?
Hi!
I'm having some problems with my Hx2110...
When flashing my working ipaq (Step 6), my computer halt.
So, i run HPRUU to reflash again, with no luck (because of "incorrect device SKU). Of course, model ID returned of my bricked IPAQ is "¨¨¨¨¨¨¨"...
But i have another chance, i try universal bootloader and USB telnet, (USB> prompt never come. (Pre-Bl screen and USB on ipaq screen are ok.)
I've tried every solution in this forum, and on internet.. (well, there's a hpruu.exe patched to ignore lang/model, but is for 6xxx series only )
What happen if i put a working 2110 on cradle, when hpruu comes with UPDATE screen, disconnect usb, and connect my non-working ipaq?...this will work?. I can try this on monday.
Thanks!
2) After doing that, put it in to bootloader mode. You do this by holding the contact button (to the right of the calendar) and the itask arrow, and then clicking the reset button on the bottom. It should now be in bootloader mode. unplug the power/usb cable and plug it back in. hit the calendar button. it should now say USB.
I just have to ask this:
What we should do before Unpluging powe/usb cable and plug it back in ???
Does it means that after putting it in bootloader mode i must put it on a cradle, then unplug power/usb cable and then again plug in it and press the calendar button ??? Or else ?
Greets, Janeku
people who installed wm6 on ur hp2110, are u satisfied with it?
Guys I Need Heeelp!!
Hellow Everyone! I am having a Hx2400 With WM5 Spanish and Firmware Version 1.02.00.H. Since i don't know any Spanish i want to upgrade to WM6 English.
I don't understand what i am supposed to.... Pleeeeease Help Me ...
I had followed jsbarone instruction but after step 3, i can not put my hx2110 on bootloader mode.i don't understand why?? i put the stylus into the softreset hole but it won't work. and then it shut down.now even i cannot turn it on (i mean put the cradle power on ) so if anyone know why please help me to fix it up !!!
Hi!
I was using Newplow's WM6 038 ROM with my N560.
Yesterday I tried to write another ROM(WM6 038 with 8MB pagepool) but during update got an error.. It said it just failed.
Now my N560 is stuck on booting screen(people climbing mountain..)
I tried Warm, Cold, Hard reset but with no luck.
Even the power button doesn't work so I had to remove battery. When I insert battery it powers on by itself.
I can enter bootloader screen by pushing power+record button so I tried to copy rom image file to SD card but it doesn't work.
I tried two ROMs(OS_213U.nbf from Original WM5 ROM and Newplow's) and 3 SD Cards(2GB SD, 1GB MicroSD with Adopter, 16GB SDHC)
Is there any recovery tutorial in bootloader mode?
Help me please!
Sorry for my English.
Have you tried flashing a ROM through the computer rather than the memory card? Try going into bootloader and flashing that way rather than the card.
The pagepool ROM is meant for N560s that have been upgraded to 128Mb RAM... have you upgraded the internal RAM to 128Mb? If you have not, then this may have caused your problem.
I had this problem when flashing to 038 normal RAM (from 035). A hard reset reset to the normal start screen, but nothing worked. However, trying a new burn with the Loox flash tool restarted the process and it worked. I found the cure was to make sure you hard reset the N560 before doing a burn. It appears to be that you have to do this to release enough RAM for the burn program to reside and for "working" storage. You may not have done this.
I suggest you try simply re-running the flashtool with SD/SDHC cards removed, battery in place, on the cradle via your PC, even though it appears stuck. The signals coming from the USB link may wake up the bootloader routine in the N560?
Solved the problem! Thanks for your comments!
I asked same question in Newplow's guestbook and the person who made pagepool rom answered. I used MTTY to revive my pda.
What I did is in below post. need translation
http://4pda.ru/forum/index.php?showtopic=55274
Hi all,
I have the same problem. N560 is stick on the himalaya picture. I tried to falsh from WM5 to new rom for Wm6 and after installation the pda stuked. So I did a warm reset and now only the start picture is apperaing. Problem is that battery is down now.
Can someone give more info on the process followed to revive the PDA ? I just cannont read russian (may be Jinsu77 ?)
Many thanks for support in advance
same problem here please please please someone help us
the only thing i can do is the l c:\os_213u.nbf on mtty program and nothing else happend to the machine
sorry for my english
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
It was me asking on Newplow's guestbook.
In case you're using Vista, you need some trick to be able to rom update. Read below.
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
And then you need to download MTTY (I used version 1.42, got it by googling) and follow below steps.
(used google translation from 4pda.ru)
------------------------------------------------------------
For rom update without ActiveSync.
1) take this set of extract, copy it to the folder with the firmware.
2) copy the file os_213u.nbf example in C: \
3) You press the button Recorder + food and poke in the hole reset (Recorder button and hold until you eat dolphins)
4) plug the device to a PC, the Task Manager, shooting process - wcescomm.exe
5) Run mtty, choose Port: USB, connect.
6) If mtty caused an error and shut down, simply restart mtty, if not typed commands, then repeat the procedure with paragraph 3.
7) in mtty command, enter: (first letter in kommande - a little l l от слова from the word L L oad)
> l l c:\os_213u.nbf c: \ os_213u.nbf
Since the end of the process will be an inscription about the error, remove the device from the PC.
9) Run rom update, zhmete "next", until you see dolphins.
10), plug the device to a PC and program.
---------------------------------------------------------------
Hope this helps you all
in advance sorry for my english
I am doing all the instructions carefully and the mtty show this
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,1A0F023Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
the pda shos the dolphins and the full blue bar
after without change anything i run the PocketLOOX5xxFlashTool that i have in the same folder with the :
EnterBootLoader.exe
OS_213U.nbf (originally rom)
RUUServer.dll
RUU.dll
and the only thing i can see is that the PocketLOOX5xxFlashTool is trying to find the pda without any luck
also the pda is stucked in the same screen with the dolphins and the blue bar
do you see any mistake in this procedure
Helppp!!! please
tuluba said:
Helppp!!! please
Click to expand...
Click to collapse
have you closed EVERY process of activesync before proceding with mtty?
I close the wcescomm.exe and the rapimgr.exe is there anything else?
The pocket LOOX 5xx FlashTool cant connect with the N560 and at the and says that Error"The language in this Flash Image update (ENGLISH) differs from that on your device()!" and i have always english rom exept maybe from the last rom "the killer" with the 128MB rom that i dont know if it is an english or something else because the device never opens to see
After flashing in MTTY(don't care about error messages), you need to unplug your n560 from PC. And then proceed romupdate until you see the dolphin picture. Now you plug n560 to PC and cilck next and wait for a while.. Hope it works!
I change the language of the rom and it works
thank very much all of you
At all they have Probs with flash from SD Card: only use a Card with 512MB! I think a Card greater then can't read by the Bootloader....
hey.
i am compeletly new here. I have the same with my n560. I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
ChrisDo said:
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
Click to expand...
Click to collapse
You can usually get back to the boot loader if you do a hard reset. I am sure you know how, if not you will find it in the FSC CDROM manual that came with the device. Let us know if this works? I have got stuck at this point too, so I know it works..... hopefully!
Hii all,
actually this my first post in the forum and i hope to find the solution to my small prob.
The problem is appearance some words on the jasjar screen like "usb" n "serial"
they doesn't disappear although i 'v done "reset" n "Power+reset+backlight"
They are permanently appear on the screen and make my jasjar as dead ..
----
actually i've open the rom upgrade icon from the mobile directly and i didn't use the pc at all because i didn't know how to upgrade it
----
please if someone know the solution of this prob. tell me >>
n i want to know how to upgrade the rom if i already downloaded it >>
Welcome to forums
have a read on my signature link and check for usb connection
Moving to upgrade section
Please orb or anyone can help >> ):
I want the software of the jasjar which come with the installtion cd ..
I tried to join the jasjar with the pc but there's a problem with the usb ..
Plese help me as my mobile now like dead body
Thanks In Advance ;
Hello,
First instal ActiveSync 4.5 in PC. - if not already installed
Code:
http://www.softwarepatch.com/windows/activesync.html
Then in settings in (ActiveSync) disable (NOT check): "allowed to connect to one of the following port" and "Allow connection to USB".
Perhaps the translation is correct. I use the CZ version. But it's second and third check box.
Now
This works for when the Universal is in Bootloader and Windows Mobile.
1. First download the ROM you want to install.
2. Extract it to a folder (use winar or other extraction software).
3. There will be up to 3 ROMs in the package: ms_.nbf (Extended ROM), nk.nbf (OS ROM), radio_.nbf (Radio ROM)
4. Delete those which you don't want to install. (If you just want to upgrade the radio rom for instance delete ms_.nbf and nk.nbf and leave radio_.nbf.)
5. Download UniversalRUU.zip
6. Extract it and copy into that folder the nbf files you want to install.
7. Enter BootLoader mode by pressing and holding the power button and backlight button whilst performing a reset with the stylus. And plug to PC. Wait few seconds.
8. Doubleclick ROMUpgradeUt.exe and follow the instructions
9. When the upgrade is finished pull out the USB cable from the Universal.
10. You will need to do a soft reset OR hard reset depending on the situation. (note: some say do a soft reset / others a hard reset .. possibly someone with more knowledge could correct me here, but until then it's best to investigate the matter for yourself on the forum.)
11. To do a hard reset (push the two menu buttons ("-") on the keyboard + the reset button at the same time (all of this three). Doing a hard reset will result in you losing all your installed apps and data so ensure you have a backup of everything first.) Everything should be fine from this time. You have to calibrate the screen and do some tutorial...
12. If after doing a hard reset you want your Universal not to install the extras from the Extended ROM wait untilsetup is complete and then do a softreset when the popup window appears (you have 3 seconds before it installs ExtendedROM)
For a long time I have not installed the new ROM. I remember so I proceeded as follows
Greetings
Svobi
Really I don't know how to thank u
Thread closed as problem got solved