Develop Bugs

voice command over bluetooth headset on xdaIIs

I have a O2 XDAIIs been tring to find what exactly I need to do to ativate voice command with my bluetooth headset I have being looking
through the forums but am unable to find the sollution if there is one can someone point me in the right dirrection PLEASE GOING NUTS

I don't think it is possible. Problems with the integratino of Windows Mobile and the Bluetooth Static/Profiles.

So, is this a Blue Angel Issue, a Windows Moblie SE isuse, or both?
If just a Windows Moblie SE Issue does anyone know if WM2005 corrects this?
Thanks!

Its a windows issue rather than a BA issue I think, however there is a partial solution.
Press the connect button on your BT headset as if you were answering a call; then press the "contacts" button on your BA. You should then be able to speak into your BT headset. Once finished, disconnect the BT headset as normal
Not perfect, but a reasonable workaround. I have my BA in a cradle in my car & hardly need to glance at it in order to find the contacts button & get nearly-handsfree operation

Its a windows issue rather than a BA issue I think, however there is a partial solution.
Press the connect button on your BT headset as if you were answering a call; then press the "contacts" button on your BA. You should then be able to speak into your BT headset. Once finished, disconnect the BT headset as normal
Not perfect, but a reasonable workaround. I have my BA in a cradle in my car & hardly need to glance at it in order to find the contacts button & get nearly-handsfree operation

Dear weasel,
I have tried what you have advised to get BT head set to activate voice command. However, it don't work. Is there any thing else that I can do? I really hope I can dial a call via BT haed set.
Thank you.

Need bluetooth help badly!~

Please help me out I'm incredibly frustrated with this thing. I recently got the PDA2k and installed WM05 on it. It looks very nice and it runs speedy with no problems. My problem is the bluetooth which is huge thing to me. Either my headset (Tekkeon Eztalker Mini) is not compatible which I doubt or I'm making a stupid mistake.
This is what I did step by step: I click on the bluetooth icon and turn on the bluetooth, I then put my headset in pairing mode and the imate is able to recognize it and I enter the Pw and I put Set as handsfree. That's it, I would think I would be done at this point yet nothing happens, the headset doesn't do anything and I know its not Tekkeons fault because I was able to hook it up easily with my HP 6315.
So what's going what am I missing?
Also theres a tab at the bottom called "Com Ports" but I only see under this option "Incoming Port", and the description at the top says there should be another option called "New outgoing port". Does this have anything to do with it?
What Am i doing wrong? It's driving me crazy I can't really use the phone without the headset.
help me out pls

Bluetooth
I know the feeling, i have gone back to 2003 cause of that but now i am back on wm5. The bluetooth issue is not fixed yet, it is not stable, it keeps going off. There is a suspend cab file, but it does not work for me yet, also try pokect zen beta. You might get a longer period of bluetooth

thanks for responding, but the problem is not that it suspends or stops working. It doesn't start working at all even though the imate detects it. It's like it's not connected at all, not that it disconnects. I'm doing something wrong I just don't know what.
The bluetooth piece is not faulty and the unit is practically brand new. whats going on?

I used "Display Switch" binded button (From Wisbar Advance 2) or "Toggle Screen" (From SPB Pocket Plus) to turn off the backlight instead of using power button .
This work around will keep bt connection alive.
Note:
1. If you suspend your BA using psShutXP your bt connection .
2. You have to disable auto turn off device under Start -> Setting -> Power

Note:
1. If you suspend your BA using psShutXP your bt connection will be disconnected.

I'm sorry I'm not sure I'm explaining myself correctly. I understand that if the power goes off I will lose the BT connection but the problem is not KEEPING the connection alive, the problem is MAKING the connection. I follow all the steps , the imate recognized the headset but I'm not able to use it..also shouldn't a headset picture show up at the top of the screen when the bt headset is connected (cuz mine doesnt). what am i doing wrong?
thanks.

still need help please.. if someone can walk me through how to setup a bluetooth connection that would be great cuz I apparently haven't done it right.

The headset icon only shows in Phone app
The headset icon only shows up in the Phone application. It no longer is displayed in the notification area (top row).
If your device is paired up, when you make a call, you will see the headset icon in the top right corner.
You may also need to clear any old pairings that you headset has. I have a Jabra 250 and it happens all the time.

there we go you have solved my problem!. I didnt' have to open up the phone application on my hp 6315 to use the bt. So wait can I listen to music with windows media player through the bt headset or does it only work when making phone calls? I was able to listen to music on the HP 6315, is it different with the Imate or is it the NEW 05 os? Please enlighten me
thank you thank you

also one other thing does this mean that if i want to use the headset with the phone that I have to press the answer button on the imate rather than the headset..cuz that would suck big time.

what about when people call me can i answer with the answer button of the bt headset or no?

It works fine with the headset button for answering or hanging up.
Later.......... 8)
droy001 said:
what about when people call me can i answer with the answer button of the bt headset or no?
Click to expand...
Click to collapse

I cant get it to work!!

Hi all,
I have been reading about the HTC Universal for a long time, but only became an owner on Monday.
I am having real trouble getting my o2 xda exec to work with my motorola HT820 bluetooth headset!
My problem is that the headset button does not trigger voice dialing.
What happens is this...
I press the headset button for a short beep and nothing!
I press it again for a short beep and my head set seems to connect to the phone and all sounds go through the headset.
But the button STILL does not trigger voice dialer.
The other thing that seems to work is that I press and hold the headset button and the phone automatically dials the last number to be dialed on the phone.
I am pulling my hair out and I cant think what the hell is wrong
I heard that the two devices made a great combination, but I can not get it to work yet.
Can anyone shine a light on my darkest hour?
P.S.
In case it makes a difference somehow, I am not an o2 customer and am with Vodafone. Because of this I removed the o2 active UI software by giving my device a hard reset and chosing a co-operate install.
I did not think this would cause any problems as I heard it was all garbage to do with o2 networks only.

Please guys this is driving me nuts!
Has anybody been through this?
I searched the boards and have not found anything
I can work on it tomorrow for as long as it takes, but I just do not have the faintest idea where to start.

Just wanted to say that I managed to get this working in the end by first using the bluetooth off cab file and then after a soft reset using the bluetooth on cab file.
Both from this thread:
http://forum.xda-developers.com/vie...stdays=0&postorder=asc&highlight=hack&start=0
I even have voice cmd working with contacts and everything!!!
I am a happy guy
Danny

ulic3190 said:
Just wanted to say that I managed to get this working in the end by first using the bluetooth off cab file and then after a soft reset using the bluetooth on cab file.
Both from this thread:
http://forum.xda-developers.com/vie...stdays=0&postorder=asc&highlight=hack&start=0
I even have voice cmd working with contacts and everything!!!
I am a happy guy
Danny
Click to expand...
Click to collapse
nice to hear, just bought a HT820 myself yesterday as finally a SHIPPING ROM with A2DP came out (QTEK weeee)
Have a problem, when i play music, i just hear the first second then it cuts out.
Also in bluetooth settings when i click/hold the stylus on the HT820 icon, i get options to set as either Wireless headset or Handsfree. Isn't this supposed to be automatic? Which do I set it to?
THanks...

try to pair 2 bluetooth hands-free devices on one phone

Hello at all,
I've searched a long time for a solution, but I really couldn't find it.
I have an
- Ameo (same like HTC x7500, with original t-mobile WM6 german) and a
- LG Style-i HBM 700 - http://www.amazon.com/gp/product/B001CZICHA , for calling.
I had bought a couple of weeks ago a wunderful bluetooth bracelet LM 959. http://www.lm-technologies.com/ci/index.php?/products/details/38
Both, the bracelet and the Style-i want and could connect to my Ameo over the same profile (phone profile, hands-free).
I've tried a couple of days, but it doesn't run as I want:
I want that the bracelet will shake when the phone is ringing (that's normal).
And then I will accept the call with my LG Style-i. If the call finish, all should go again in stand by.
If the next call arrive, the bracelet have to shake first, and so on.
But reality is hard and bad:
If I power on the bracelet, and power on the LG iStyle the bracelet go in sleep and the LG Style-i is active connect to my Ameo. No action's could make the bracelet function, only if I power off the LG Style-i. But than I couldn't take a call (not with this brick on my ear)
I think both are using the same profile (hands-free). And only one could go in active, or ?
Is there a way to let both function, and as I want ?
I would be lucky for any suggestions.. any idea ?

I'm afraid I can't answer that with any experience, but I think the bluesoleil driver will allow connections to two devices.
When someone with more experience comes along, does anyone know if it is possible to connect two devices with different profiles.
I wish to connect my car kit (HFP) and an audio streaming connection (A2DP), to a kaiser, and keep them both connected.

ping, I want infor on this to for my ameo before I buy the bracelet!!

new status:
I've seen, that all entries in the registry between the braclet and the LG style-i are different. Not the channel entry : both are channel 0x2.
I've changed the channel from bracelet in the registry:
HKLM/Software/Microsoft/Bluetooth/Device/001b3500023b
from 0x2 to 0x1.
Bracelet connect with Ameo furthermore, but situation doesn't changed.
Now I will change the ROM from 6 to 6.1 (from original t-mobile 6 to sogarth 6.1) this weekend.
let me see ...

bad story ... sorry.
I've changed the ROM from original t-mob WM6 to sogarth WM 6.1 ROM but without any changes.
I've no solution to connect the bluetoorh bracelet AND the Bluetooth headset at the same time.
Any other idea's ?
please help ...

Not possible afaik. I personally tried it when I had two Motorola s9s and only one would connect at the same time :S.

Does anyone know if you can connect to *different* profile devices?
I want to connect a HFP device and an AD2P device.

ian_c said:
Does anyone know if you can connect to *different* profile devices?
I want to connect a HFP device and an AD2P device.
Click to expand...
Click to collapse
Hello all,
I'm currently using wm6.1 build 20273.1.3.3 cook (FInixNOver v3.6) on my Trinity with iDream BTSH01 + Nokia BH-102.
The BTSH01 can act as either "Hands Free" or/and "Wireless Stereo" (A2DP).
I can select which mode I want to use on that device by using the standard "Bluetooth Settings-->Device" menu.
The BH-102 is only an "Hands Free" device.
I successfully can listen music on the iDream and make/receive calls with the Nokia.
As you may guess, my main use of these combination is on the car! the Trinity is used as my MP3 player, my GPS and my phone with ear bud, while its battery is being charged.
The BH-102 works very smooth alone! just need to power it on, wait 2-3 seconds to ear the beep and start to use it, even while receiving a call (it happens a lot while I'm driving!).
That particular cook has the BT sound volume adjustment working very well!
The BTSH01 is tricky to pair... I always have to start it in "pairing" mode and do a BT search on the Trinity (I have a button on the "Today" for that!) to have it work properly. If I not do this way, the music is shopped in 500ms pieces !!!
I can only launch the music/sound app (Mortplayer and/or GPS app) after pairing it. If not, the sound goes out through the internal speaker.
By having the BTSH01 decoding music, the HTC becomes slower (still ok for the GPS app)!
Now, combining both... I'm using both since a couple of days and I still have no procedure to have both running ok (BTSH01 as "Wireless Stereo" and BH-102 as "Hands Free") at first shot!
Sometimes the BTSH01 start to decode my calls, sometimes the BH-102 is not able to pair ... it's always been asked the PIN code.
But, once both are up, I have no more troubles and can start my trip!

i'm using an r35 itech set as handsfree...although it can be switched to include a2dp. however, i also have a sony ericsson car kit that's set for a2dp or wireless stereo. thus, when i'm in the car my u1000 automatically connects to the ericsson and thus streams the music. any calls that come i can answer through my r35. when i leave the car, the ericsson then disconnects with my u1000 (either through range or when i shut off the ignition). my r35 is continuously bonded and thus any calls are answered through it.
i don't think it's really possible to connect 2 bt devices with hands free profiles at the same time. i tried that with both my r35 and ericsson kit....if the first device bonded is my r35 a message appears on my ameo indicating an error when i try to set hands free. it only accepts wireless stereo.
cheers

I don't think so. In my opinion it's not possible. u can use stereo.

bluetooth paring problems WM6.5

Yesterdaty I updated to WM6.5 and now try to get everything working again. Somehow my TP2 won't pair with my bluetooth carkit anymore. With WM6.1 this was no problem. The phone still pairs perfectly with my computer (also bluetooth connection) so I think the bluetooth connection is ok.
When parining to my carkit it finds the device, then I have to enter a password on the TP2, and after that it just sais "pairing connection failed", and it will not work. I am sure the password is not changed since yesterday. I tried it several times. I do not know what to do anymore. Could this be a setting somewhere? I get the feeling my password is not send properly but have no idea.

Meanwhile I tried pairing my carkit with another phone and no problems there. So my conclusion is: something has changed with bluetooth, updating to WM6.5 which makes it now impossible to pair my TP2 with my carkit.
Is there maybe a programm for the TP2 which give me more controll over bluetooth (like maybe go to an older standard)?

I have exactly the same problem as you

good to hear I am not the only one. Hope someone will come up with a solution for this.

I did nor observed any issues when pairing my TP2 after reflashing to WM6.5
There is another issue however - I can not hear any voice until it is charging.
Unplugging of the charger fixes this issue immediately. Horrible...
Seems, HTC guys are saving money on testing by using us as Beta Customers.

Would a custom ROM be a solution for us?

I updated to the "energy 6.5.1 rom" and guess what..............
The same problem. The rom is very nice, but my TP2 still won't pair with my BT carkit which is very big problem for me.
Is there maybe a way to downgrade just the BT part of a rom to WM6.1. I read on different forums there is something that is called a BT stack. Could this be the problem?

I have a ton of problems with bluetooth pairing now. However, I don't know whether it's the fault of 6.5 or the Tilt 2. Here is what I am experiencing...
- On car deck or headphones, the skip buttons don't do anything
- on car deck or headphones, I have to disconnect Stereo Audio and then reconnect to actually get sound. It NEVER works when it auto connects.
- Music will do a brief skip when you shut the screen off
- Stupid message about volume control every time it connects (resolved by switching to custom rom)
- SMS or any kind of alert tone now turns music way down so that the tone is the only thing you hear. Which is super awesome when I'm driving my drunk friends around and they are singing along to a song when suddenly it mutes so everyone can hear my incoming text message.
Not a single one of these issues existed when I had my Fuze.

Same here
My bt headset (sony hbh ds970) and simply does not find the pairing...
I asume is a problem related to energy´s ROM

orb3000 said:
Same here
My bt headset (sony hbh ds970) and simply does not find the pairing...
I asume is a problem related to energy´s ROM
Click to expand...
Click to collapse
No I do not think so, because I used the official WM6.5 with the same problem. Does someone know a way around this issue. I strongly believe that if only I could pair I have some options to work with it (in 6.1 it worked like a charm). If I only could pair without having to send the passkey it would be great step forward. I presume with sending the passkey, the bluetooth of the TP2 sends out other "rubbish" that confuses my carkit.

My problem is solved and guess what, it had nothing to do with my TP2. The problem was my carkit. It has a maximum number of bluetooth devices (5) it can pair to and the last one (the WM6.1 version of my phone) had been reached. So a hard reset on the bluetooth carkit and the problem was solved.
Well, at least I now know how to flash a rom to my phone and I think I learned more about the phone reading through all the forums. Thanks all for thinking with me on this problem!

Does anyone else still have this problem?? I have removed all the devices from my car and continue to have the same pairing error just after entering the passcode. Stock Spint ROM worked great, but multiple 6.5 upgrades don"t pair..............suggestions/ideas??????

bluetooth settings, advanced, enable beam data exchange,check the box

Interesting.....I actually found a fix. Instead of pairing the phone with the car, I paired the car with the phone. I didn't even know that this was possible, but it did the trick!