Active Sync Problems with WM 6.1 - 8525, TyTN, MDA Vario II, JasJam ROM Development

I posted this in the TNT thread but thought I would start a general thread to get some ideas with this.
Anyone else having active sync problems?
I got a new handheld through warranty replacement and went through the whole process: SIM unlocking the phone, Hard SPL, flashing to factory ROM, then flashing TNT, then upgrading radio...
Worked flawlessly for 3 days...Now all of a sudden AS will not connect. You can here the connection sound and the battery will charge but AS will not kick in or attempt to connect.
I've tried it on 3 different computers...and still nothing.
My questions are:
1) Is there a registry hack or a place that I look in the registry or possibly a missing ROM file???
2) I started using a non-ATT and non-HTC wall charger...could this have caused it?
There are the programs I have installed:
SPB Mobile Shell 2; SPB Pocket Plus 4.0.1; SPB Phone Suite; SPB Insight; Battery Status with Clock Skin; Today Agenda; PocketWeather 2.0.7; IM +; ePoctrates (with auto-update enabled); a few paramedic programs; and google search.
Has anyone seen compatibility issues with these programs and WM 6.1?
I have done the tick and untick in the USB to PC connection setting tab and that was a NO GO....also tried completely uninstalling and then re-installing AS 4.5 and soft resets...
I've never had this issue.
If I can't get it figured out, I guess I'll re-flash....again...
Thanks in Advance,
Jim

FIXED IT!!!
Had to use MemMaid to "recreate activesync".
Jim

im having this problem too but i cannot install anything on this phone because my phone(8525) stopped recognizing memory cards =( even after upgrading my rom.

Related

Activesync Caput!

Since upgrading to WM6 Shadow, then CUSTEL ultimate I have had serious problems with Activesync.
AS is scheduled to sync with exchange server ev 10' in peak times. It usually works fine for a while, then it gets stuck: forcing a manual sync won't launch a gprs connection. Checking new exchange emails manually does not work either. the two problems are obviously related (to AS schedule?)
When i open the task manager, it works fine until AS gets stuck - then the task manager gets stuck too when identifying which programes are running.
i did not experience this type of problems when using JJ's earlier versions of WM6 but it has now become a common problem since upgrading to the latest rom (Shadow) and CUSTEL.
Have you got a similar problem?
How can I kill AS on the device, and start afresh? A soft reset won't do it. I am fed up of having to hard reset every few days..!
having the same problem!!!
using Satin Rom

I Need A Solution For The Wifi,nothing Worked!!

I NEED A SOLUTION FOR THE WIFI ,NOTHING WORKED!!it works sometimes,,,the problem is the famous problem of starting it,,,the lamp flashes but the tower doesnt show,,,!
i used every known rom and 2003se and wm5 nothing helped it works sometimes and someother times not,,,,,
it needs soft reset sometimes,,,and some times very resistant
my radio version now is 1.15 and 3.5.2 R5 wm5 and still sometimes i can start it and someother times i cant.....is there any fix for that?
i will sell my BA if i cant find one!
lotfytronics said:
I NEED A SOLUTION FOR THE WIFI ,NOTHING WORKED!!it works sometimes,,,the problem is the famous problem of starting it,,,the lamp flashes but the tower doesnt show,,,!
i used every known rom and 2003se and wm5 nothing helped it works sometimes and someother times not,,,,,
it needs soft reset sometimes,,,and some times very resistant
my radio version now is 1.15 and 3.5.2 R5 wm5 and still sometimes i can start it and someother times i cant.....is there any fix for that?
i will sell my BA if i cant find one!
Click to expand...
Click to collapse
I know excatlh the problem you mean as mine has done that for a long time. however, since I flashed Helmi's Wm6 rom mine hasn't done it again. it maybe the fix you need then again it may not depending on your device.
Mine is originally and Orange M2000 and prior to trying Orange's last official rom and t-mobile's latest rom as well it was still doing exactly as you described. make sure your moel is listed in helmi's description of compatable devices. and remember to do pim backup and backup you Storage arear before flashing as it combines internal storage to main memory in the wm6 rom
hope that helps
I just got my BA a few days ago. Did the WM6 upgrade today, and the wlan was doing this.
I noticed that it was happening after I'd sync'd it and the wifi connection was disabled by ActiveSync. I went into the Connection Settings on ActiveSync on my computer (ver. 4.5) and checked the "Allow wireless connection on device when connected to the desktop"
So far, this has worked. I've been able to sync my BA, disconnect, and reconnect to my wireless connection without having to do a reset first.
Nita
wheatfree said:
I noticed that it was happening after I'd sync'd it and the wifi connection was disabled by ActiveSync. I went into the Connection Settings on ActiveSync on my computer (ver. 4.5) and checked the "Allow wireless connection on device when connected to the desktop"
Click to expand...
Click to collapse
This appears to be a bug in the ROM. Activesync on the phone doesn't always realize that the connection is gone and gets 'stuck' in a loop trying to sync to a now-missing computer. Closing activesync on the phone will also clear it and allow the wifi to work after syncing.
i flashed it with wm6 but the wifi probelm still exists,,,only the lamp flashes but no tower is showing,,,,,,,,,,and i tried the wlan manager,,,and the com manager nothing helped
I have exactly the same problem, i think its an hardware error.
the problem started half a year ago with wm2003, yesterday i flashed wm6 but the bug still exists
after multiple switch on-and-off sometimes the wireless works, sometimes it takes just a while 5-10 minutes.
if theres somewhere a solution, please let me know
after a soft reset open CommManager, Setup, Wireless LAN an Select "TURN ON WLAN".
This dont conect.
But, after you do that, you can use te On/Off button of Wifi on te CommMannager with any problem...
You need to do this, only one time after a Soft Reset.
Can this be done via a script, reg key or even a Visual Basic App that opens the Comm Manager and the Wireless Manager and selects these in sequence? I have a profile switching software (PhoneAlarm) and it works a treat all for the activatation of WLAN. Sometimes it works fine, others, it doesn't.
As I am running WM6 and it's lovely undocumented feature (bug) of the time and password both being in volitile memory, each time I take my battery out, I have to rebuild the 'ken device as I cannot unlock the screen. I have resorted to using SPB backup nightly and a reboot after backup (as the device seems to work better with a daily reset (hey, it ain't stable yet - we are still waiting Billy)). This is where the Wireless issue comes into play.
Do I settle for Profile switching with wireless powering on correctly or do I backup my device and ensure that I am not re-imaging the stupid thing every day when I take out the battery! Mobile device - bulldust! Not very mobile when you have to keep it plugged in to ensure the battery doen't run out! My Laptop is more mobile!
jriquelme said:
after a soft reset open CommManager, Setup, Wireless LAN an Select "TURN ON WLAN".
This dont conect.
But, after you do that, you can use te On/Off button of Wifi on te CommMannager with any problem...
You need to do this, only one time after a Soft Reset.
Click to expand...
Click to collapse
no, that doesnt work with my BA

GPRS broken in WM6? - Can somebody test?

I have an interesting situation with my Orbit. This never occurred with WM5, but only since WM6.
Description:
After a fresh boot, the device works perfect, and connects to GPRS when needed, and I am able to direct push my email all day long. Now, if I go into Comm Manager, and stop the phone radio, and then start it again, I am no longer able to connect to GPRS, and neither are any other applications. ActiveSync and DP don't work anymore, neither does IE.
The only solution to the above is to soft reset the device again, and things go back to normal.
Troubleshooting:
I've tried the regkey to keep GPRS always on. I've also tried to disable any today plugins that could be causing this issue. I've even tried a hard reset, but the same behaviour occurs. Oddly enough, this problem also occurs on a WM6 based Hermes device, and never did before when using WM5.
Something weird is going on with GPRS and WM6 in general. Sometimes, I will be on the train without reception, and when my phone gets signal again, GPRS will say it is connected, but it is not. I have to soft reset.
Needless to say this is annoying. Can somebody confirm that this issue exists with the base O2 WM6 rom? What about some of the other ROMs here that you guys/girls have? Does the same behaviour occur? My ROM and radio are just the defaults, no upgrades, etc.
N.
Hi There,
I am well aware of the problem, I currently work in a telecoms company and the main device we ship out is the XDA Orbit (Artemis).
Currently we are downgrading all devices so as to ignore the problem, but a permanent solution is being worked upon.
The HTC Touch's radio is identical to that of the Artemis, this problem does NOT exist on the Touch (Thanks for testing Pof!) So I atleast have ground to work upon, it is not related to the radio itself but the RIL (Radio Interface Layer) driver.
I'll let you all know if (or rather WHEN) I find a solution.
i've had loads of trouble with this issue and here are my findings:
the dopod sea 3.7 rom and and anything else based on it are the worst affected.
the o2 wm6 rom isn't too bad
tom and meschle's roms are both pretty much fine
I do a 20 minute tube journey every day so i have tested this quite well!
cheers
alex
I'm having the same issue in the Artemis Touch 2.1 Rom.
I found that when I disabled the Phone option, the Flightmode-option would enable. Now, when I want to enable the phone, I tab the Flightmode option to disable Flightmode. It then enables the phone automatically and successfully opens the GPRS connection.
Just done this a couple of times but for now this seems to be a workaround.
Read 'seems'
GuyBrush1978 said:
I'm having the same issue in the Artemis Touch 2.1 Rom.
I found that when I disabled the Phone option, the Flightmode-option would enable. Now, when I want to enable the phone, I tab the Flightmode option to disable Flightmode. It then enables the phone automatically and successfully opens the GPRS connection.
Just done this a couple of times but for now this seems to be a workaround.
Read 'seems'
Click to expand...
Click to collapse
The times I have had the issue with the O2 rom and the v.occasional times I have it with Tom/Meschle roms restarting the radio via flight mode always fixes it. With the Dopod and other 3.7 roms the whole radio seems to crash and you can't even get it into flight mode so soft reset is the only option.
This has been tested on all versions of the Artemis radio that are available.
same problem here on prophet. can connect. if i go ffline due to no signal, i cannot connect. after i switch to flightmode and activate phone again gpry works again. any patch?!.
holzzelt said:
any patch?!.
Click to expand...
Click to collapse
No patch, just better roms.

Problem with WM 6.1

I downloaded Windows Mobile 6.1 about 2 weeks ago and I have really thought it to be a step up from version 5. However, I am having a problem with the messaging. When I go to my inbox it says it is receiving an MMS and the clock on top is pushed over to the middle. After this it will start scooting the whole screen over to the left. Also, I am unable to run messaging after this because it seems to time out or something. I have uninstalled 6.1 and downloaded it again hoping this will fix the problem but it never does. I was wondering if anybody has had this problem or if anybody knows how to fix it before I return to the T-Mobile recommended WM.
Thanks,
Brad
did you use the built in connection setup program? If not, start there. I have played with a lot of the 6.1's on my Dashes, and the connection wizard has always worked for me
yeah, still no luck.. i'm thinking it has to be a problem with the WM 6.1 itself, although i've tried to find a different version each time i've had to install it again.
6.1
Have you tried Rickwatt's v24, I've been using it for a while , done a lot of modding and I've never had any mayor problems.
I installed v24 to my phone 2 days ago and it is still doing the same thing. I'm not sure what is going on, i was hoping somebody had had this problem before.

Probelm with WiFi

Hello there,
What I Have: Att 8525 Herm100
Rom: Att's Mobile 6
Everything is stock but the extended life battery
The problem I am having is when ever I try to activate my WiFi the phone doesn't do anything. I am not sure if there is a wifi card or not but that's want I want to know. I have tried everything from activating it in com manager to going into the settings and activating it manually and nothing happens it acts like I didn't even hit the button to activate it. Is there a wifi card in the phone or is it integrated on the motherboard in the phone. Note: I bought this phone off e-bay and the wifi never worked when I received the phone.
I am new here and if there is a post about this already I am sorry.
I hate it when that happens.
To begin, there were two ATT OEM WM6 roms relevant to the 8525 that I noticed deep in the bowels of XGA.
I chose the later file (higher revision numbers) I found it here:
http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
From comm manager when I click the tower button on within a second the spinning windoze icon shows something is happening. It then starts "sniffing" for my preset wifi connection (ATT supplied 2wire portal 802.11g).
Now, if yours does not show the spinning windoze working icon when you turn on wifi? There obviously is a problem. This could be software, or hardware related (duh). If there is no error message related to "wifi is not an option, unavailable, or screwed" then my first guess is there is something missing or damaged in the ROM update that was applied to your device. As far as I know all 8525 (herm100) were shipped with wm5. It had been mentioned in the volumes of xda that the first AT&T WM6 rom was a little buggy. Try the later released AT&T WM6 update.
It was a run file so no muss no fuss. Sync the phone run the update from the pc, three minutes later the phone is flashed to ATT WM6 professional.
You could take it to a ATT shop? But, I think that without a doubt they would hand it back and say you need a new phone with a 20 year contract and 3g data plan even Obama would blush at.
Try the hard reset. take a picture of the startup screens so you have the numbers and see if the wifi startup is working after the reset. If not then compare the numbers to the above mentioned roms. If the indications are you have the first issue of WM6 from ATT try flashing the second release. If that still fails then your device could indeed have a hardware problem.
The wifi is indeed built into the system and if that chip on the board is not working it could be a overly expensive problem. Possibly a shop has a working board they would swap out cheap? Otherwise, it is a fun phone you can keep notes on, run gps software if you have a bluetooth gps receiver and software like tomtom.
To be honest the wifi on my 8525 has been convenient when around the house to check the local weather radar when I hear a thunder outside, or browse headlines from the porcelain room or even leave messenger turned on incase a gamer friend is looking for someone to get shot up in a game.
I have used the live search voice thing to amaze the neighbors once. But, the limited range of wifi is a real drawback to how truly wonderful that addition could be.
HELP Please! Wi-Fi not working!!!
Hi to XDA all users !!!
MY Hermes - HTC TyTN [Herm200]
I bought HTC Hermes myself year ago.
there was flashed a WM5.0, I've just downloaded from here HARD SPL & WM6,1 (Custom) Flashed.
Wi-Fi will works on WM5.0.
Well here I am at 6.1 flashed and now is not working Wi-Fi. When i pressed Power ON - loading long and nothing happens.
Other methods are also tried on Commanager and Settings - but did not help.
What do I need to do my dear.
HELP!
Thank you for your attention!
Hi Nurk.
Since the wifi worked on wm5 but failed after the 6.1 flash. I would guess the problem is in the 6.1 components. You might start with contacting the kitchen rom you employed for WM6.1 thread and see if this has happened to others. Next step would be to check the radio rom version. I did see on xda an assortment of Radio roms.
If your not totally in love with the current rom you have flashed? Try another 6.1 or even a 6.5 and see whats poppin.
and what you have in HKLM\Software\HTC\CommManager\WLAN\DeviceName?
utak3r said:
and what you have in HKLM\Software\HTC\CommManager\WLAN\DeviceName?
Click to expand...
Click to collapse
I have get this from registry:
HKLM\Software\HTC\CommManager\WLAN\DeviceName - {98C5250D-C29A-4985-AE5F-AFE5367E5006}\TIACXWLN1

Categories

Resources