Develop Bugs

Reverting back to complete WM5

Hi All,
I've been playing around with various WM6 ROM's but I have now decided to sell the phone (I want a Kaiser!), anyway whats the best way of reverting back to the original HTC booloader & WM5 ROM. I ask this because I still have valid warranty but only if HTC never find any traces of different ROM's??
I assume I would use ROM
HTC English HTC__001 1.23.405.2 1.07.0000 1.38.00.11 ??
but what about the bootloader??
Any advice would be a real help
Cheers
Ody

You should have the original ROM on your phone just hard reset it using the key combination to reinstall...

odyseus said:
Hi All,
I've been playing around with various WM6 ROM's but I have now decided to sell the phone (I want a Kaiser!), anyway whats the best way of reverting back to the original HTC booloader & WM5 ROM. I ask this because I still have valid warranty but only if HTC never find any traces of different ROM's??
I assume I would use ROM
HTC English HTC__001 1.23.405.2 1.07.0000 1.38.00.11 ??
but what about the bootloader??
Any advice would be a real help
Cheers
Ody
Click to expand...
Click to collapse
incorrect.. hard resetting will just wipe your data, not revert your ROM to original factory ROM
if you have the official ROM from your manufacturer, it should come with SPL packaged in it.. run SSPL manually and then run the official ROM update

I thought that part of the ROM comes with a hidden partition of WM5 so that in event of problems you could reflash back as it says in the manual? This is quoted in many threads! ie. Flash WM6 as much as you want and in event of problems just restore back to original state.

Yes but by flashing the orginial WM5 that cane with the device...
If you flash with WM6 the "Hidden" section will restore WM6 i.e. whats on the device..

so what would be good then is if there was a simple tool for backing up a rom to a PC like the one Orange used to do instead of all the command line converstions etc...

if one enter the bootloader and format the reg and storage that way
it's like an old fasion hardreset
everything will go back to the org rom settings
but never to a former rom if one have flashed it to a new one

hence is the a way we can simply backup our present ROM exactly as we have it now before flashing?

you can do a dump of your ROM to make a backup of it.. although it's a bit troublesome. Depending on your carrier, they may actually have your official ROM on their site, or it may be in the wiki, so not everyone needs a ROM dump

yep.. but if you changed WM5 and installed progs exactly as you wanted it then its good to get a backup...

umm.. yeah... i guess that goes without saying. you could use sprite or something.. then flash the same original wm5 rom and restore your backup

yes but would be more handly to create a flashable rom backup

Flashing a cooked rom - further tips

As a number of you are having problems flashing cooked roms I put up this sticky.
1. If you presently run a factory wm5\wm6 rom then uspl cid unlock (step 1 in my roms) your rom before you flash cooked rom.
2. If you have a cooked rom on your device already and are changing to another cooked rom (especially if rom is from a different cook) i would recommend you:
a) flash back to factory rom first
b) then cid unlock
c) then flash the new cooked rom.
This is because sometimes the new cooked rom does not function 100% on first flash and a repeat flash is required.
3.Alternatively (especially if you dont have access to the factory rom) flash the new cooked rom twice to be sure new rom has taken properly and if device is already cid unlocked there is no need to cid unlock again.

Thanks for your hard work
Yes flashing twice works!!!

Thanks
Thanks Meschle

No Navigation application included in ROMs
Maybe this is also interestening for newbies;
there is no TomTom or iGo in the ROMs included (this is a often asked question)
but you can download TomTom from their website for free (you only have to pay for the maps)
After installing TomTom - just insert your TomTom CD and install your maps from there.

meschle said:
As a number of you are having problems flashing cooked roms I put up this sticky.
1. If you presently run a factory wm5\wm6 rom then uspl cid unlock (step 1 in my roms) your rom before you flash cooked rom.
2. If you have a cooked rom on your device already and are changing to another cooked rom (especially if rom is from a different cook) i would recommend you:
a) flash back to factory rom first
b) then cid unlock
c) then flash the new cooked rom.
This is because sometimes the new cooked rom does not function 100% on first flash and a repeat flash is required.
3.Alternatively (especially if you dont have access to the factory rom) flash the new cooked rom twice to be sure new rom has taken properly and if device is already cid unlocked there is no need to cid unlock again.
Click to expand...
Click to collapse
Hi guys, I'd like to try one of your cooked roms but unless I tried to gather infos from the forum I still have some doubts....
First of all... the cid unlock procedure is needed only for the devices that are operator branded right? I mean if I have a normal HTC no brand I don't need to do this step... is this correct?
And last but not least.. how can I flash back to the factory rom??? Is the procedure the same? I tried to find my original rom but I couldn't... Does anyone can help me in finding it? (I've got the italian rom installed).
Thanks to everybody...
Ciao
Shift.

Before you start to cook your own rom...
May I add that's also very important to have been through the whole process (at least one time) of recooking an original rom without adding/removing anything ?!
That's the price we need to pay in order to achieve successfull rom cooking !

difficulties to flash artemis
i have M650 (orange) wih WM4. it was unloacked by orange.
i'm not able to flash it.
i have the error 270 fconnect lost or file corruoted
how can i solve my issue?
meschle said:
As a number of you are having problems flashing cooked roms I put up this sticky.
1. If you presently run a factory wm5\wm6 rom then uspl cid unlock (step 1 in my roms) your rom before you flash cooked rom.
2. If you have a cooked rom on your device already and are changing to another cooked rom (especially if rom is from a different cook) i would recommend you:
a) flash back to factory rom first
b) then cid unlock
c) then flash the new cooked rom.
This is because sometimes the new cooked rom does not function 100% on first flash and a repeat flash is required.
3.Alternatively (especially if you dont have access to the factory rom) flash the new cooked rom twice to be sure new rom has taken properly and if device is already cid unlocked there is no need to cid unlock again.
Click to expand...
Click to collapse

unsuccess cooking flash
it is my first flashing.
i feel to have follow-up all step
connect usb cable, and go head
but it seems not working.
kulbut0r said:
May I add that's also very important to have been through the whole process (at least one time) of recooking an original rom without adding/removing anything ?!
That's the price we need to pay in order to achieve successfull rom cooking !
Click to expand...
Click to collapse

i succed to do it.
even if the m650 was unlock by the provider it is needed to do it with uspl.
tnx
Marcos Paolo said:
it is my first flashing.
i feel to have follow-up all step
connect usb cable, and go head
but it seems not working.
Click to expand...
Click to collapse

So if i whant to go from B&B4.3 Englisch version to the Dutch version, must i cid unlock my device again ? Or can i just flash from Englisch to Dutch ?

NP9660 said:
So if i whant to go from B&B4.3 Englisch version to the Dutch version, must i cid unlock my device again ? Or can i just flash from Englisch to Dutch ?
Click to expand...
Click to collapse
only flash the new one.

Just like to add that sometimes the ROM file renames itself to an N file even if you rename it back to a NBH file so watch for that before flashing cooked ROMs

using the ROM Update utility, how do I get it to choses the correct rom file. Cooked one with extended rom how do I get tit to choose this file?

XDA-BOJ said:
using the ROM Update utility, how do I get it to choses the correct rom file. Cooked one with extended rom how do I get tit to choose this file?
Click to expand...
Click to collapse
DONT CROSS POST - ESP IN A MODERATORS THREAD

Sorry... Ill take that as a slapped wrist... should had read the rules , but I am a bloke !!!!....

XDA-BOJ said:
Sorry... Ill take that as a slapped wrist... should had read the rules , but I am a bloke !!!!....
Click to expand...
Click to collapse
No problem - we are all blokes here - probably none of them read the instructions.

prank1 said:
Just like to add that sometimes the ROM file renames itself to an N file even if you rename it back to a NBH file so watch for that before flashing cooked ROMs
Click to expand...
Click to collapse
Thanks for the tip you saved me from lot of frustration.

tray to flash the rom without sd inserted

shift_runstop said:
Hi guys, I'd like to try one of your cooked roms but unless I tried to gather infos from the forum I still have some doubts....
First of all... the cid unlock procedure is needed only for the devices that are operator branded right? I mean if I have a normal HTC no brand I don't need to do this step... is this correct?
And last but not least.. how can I flash back to the factory rom??? Is the procedure the same? I tried to find my original rom but I couldn't... Does anyone can help me in finding it? (I've got the italian rom installed).
Thanks to everybody...
Ciao
Shift.
Click to expand...
Click to collapse
The above questions asked are really important for the ppl flashing their ROMs for the 1st time. I want to add some more questions
- How to put the original ROM back on the device.. (could not find the steps for the same)
- CID unlock. If i put the original ROM back on the device, will it automatically take care of the CID which was unlocked before (to flash the cooked ROMs)?
- Is there any way we can see CID info on the mobile?

arinjayw said:
The above questions asked are really important for the ppl flashing their ROMs for the 1st time. I want to add some more questions
- How to put the original ROM back on the device.. (could not find the steps for the same)
- CID unlock. If i put the original ROM back on the device, will it automatically take care of the CID which was unlocked before (to flash the cooked ROMs)?
- Is there any way we can see CID info on the mobile?
Click to expand...
Click to collapse
to put the original ROM just get it and flash it when needed
and when flashing it it don't need CID unlock or anything and it will bring back your device to original SPL, IPL, Radio and ofcourse the OS
cheers

[HELP]HELP!!!!!

I Have Got An Orange Uk Diamond And Have Been Trying To Upgrade From Rom 1.37.405.1 Wwe To 1.93..... But Was Unsuccesfull. I Have Got Few Questions.
1. Is It Possible To To Do It(1.73 Rom To 1.93)
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
I Maybe Asking For Too Much Here.
And Sorry Guys For The Newbie Questions. As It Might Have Already Been Answered A Million Times. I Just Couldnt Find Them.
Thanks In Advance.

When You Type In All Caps It Makes Your Words Normalised But Every Word Has A Capital Letter
Just In Case You Wanted To See Who The Idiots Were

yuv said:
I Have Got An Orange Uk Diamond And Have Been Trying To Upgrade From Rom 1.37.405.1 Wwe To 1.93..... But Was Unsuccesfull. I Have Got Few Questions.
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.
I Maybe Asking For Too Much Here.
And Sorry Guys For The Newbie Questions. As It Might Have Already Been Answered A Million Times. I Just Couldnt Find Them.
Thanks In Advance.
Click to expand...
Click to collapse
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.

Since you're not giving any details I don't know what your exact issue is. It depends on your Phone and where you got it.
Most likely your issue can be resolved by reading the thread which I link to in my signature.

daleski75 said:
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.
Click to expand...
Click to collapse
If you HardSPL you wont be able to install a standard HTC ROM without some faffing, I had this problem this week, so if your 1.93 is the released Standard OEM HTC one then dont HardSPL whatever you do.

thanks alot guys. what a quick response. and sorry for the caps lock if it got u confused.
as far as the details of the phone is concerened. its an orange UK contract phone with the ROM version 1.37.405.1 WWE radio 1.00.25.03. the phone hasnt been flashed at all. i did try to flash it to _QMR_RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe but was unable to. i guess i should have hard spl it before.
i m guessing the only thing i need to do is to hard spl it right. or do i need to do something else as well.
again thanks alot guys for the quick responses.

hi tony.
i have actually tried to do it without hard spl but it would get stuck on 1%. is there any other way to do it. i believe the ROM i m trying to flash to is an official one as far as the thread i downloaded it from is concerend.

one thing to clear here. its the first time i m trying to flash from 1.37 to 1.93 official rom. could someone confirm that there is a 1.93... official rom available or is it one of the cooked ones. and could one confirm as well that i need to hard spl even flashing from oficial to official rom. coz two post before tony mentioned not to hard spl.
any ideas guys. thanks

Here's what I've just done, I hope it helps -
Vodafone UK to UK release HTC ROM.
1. I read the info here, over and over and asked lots of questions.
2. I checked the current SPL of my fone (Volume Down & Reset) and found I had 1.37.
3. Downloaded Hard SPL 1.37 UnSigned and installed it - Here was my first problem. Everyone just says use RUU to install hard SPL however the SPL's I downloaded didn't come with RUU so I took a guess and decided that RUU was a generic flasher which could also flash the SPL for me.
4. Use RUU to flash the SPL, mine reported V1.0 as the new ROM version but installed and rebooted perfectly to reveal the coloured screen informng that I did now have a Cooked SPL installed.
5. Followed the fisrt startup procedure that the phone asked me to do.
6. Flashed the new ROM in a similar way to flashing the Hard SPL.
7. Phone flashed ok and I'm just in the process of setting it up now.
One issue I did have was using Vista I had to right click and run as Administrator to make it work.

tonyb15re said:
If you HardSPL you wont be able to install a standard HTC ROM without some faffing, I had this problem this week, so if your 1.93 is the released Standard OEM HTC one then dont HardSPL whatever you do.
Click to expand...
Click to collapse
wrong. if you use unsigned hardspl (aka "developer hardspl") it will flash HTC ROMs just fine
1.93 is also unsigned.

vrstu said:
3. Downloaded Hard SPL 1.37 UnSigned and installed it - Here was my first problem. Everyone just says use RUU to install hard SPL however the SPL's I downloaded didn't come with RUU so I took a guess and decided that RUU was a generic flasher which could also flash the SPL for me.
Click to expand...
Click to collapse
who's "everyone"? this information is totally wrong, wrong, wrong.
next time you download an attachment from a post, read the post where the attachment was, and you won't have this problem (the post that had the unsigned hardspl 1.37 also talked about where to get the special SSPL RUU for it - have a guess. it is in the same post in another attachment).

Thread has been closed due to maintenance of the forum. If you want it reopened, PM a MODERATOR!

Back to Original ROM and CID Lock

Dear Friends;
I've done HardSPL and installed Cooked ram (downloaded from XDA) several times, but recently I heared that by installing non-original ROMs the Guarantee will be invoked. It is easilly possible to back to original ROM but is it possible to back to original CID lock as well? I dont want loose the Guarantee....
I will be appreciated if the firends kindly help me.
Best Regards
Darius

As far as I know you can go back to your original SPL, but dont quote me on it.
Wait for a better answer from someone more experienced.

at the same place where u got the hard spl, the author probably provided the stock spl for warranty purposes.
so what u need before u send it back to service is:
stock spl, stock rom, and stock radio (probably u remember which came with it).
any ways, just read the hard spl thread, and u have the answer.
don't do nothing without first reading what u are doing

easy!
hi, simply install an ORIGINAL HTC rom and it return with rom and original CID.
Bye, felix

AFAIK installing another rom also the HTC default ones are not giving back the CID when u unlocked it, if you wrote the CID down you can do it with the CID unlocker of OliNex there u can write in the CID u want to set.
The problem with stock SPL is dicussed many times ! a whole thread is there for that.
Greets
ps. http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39

Step by step guide is here post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4

Back to Original SPL
Dear Friend;
I've done all steps and successfully installed stock SPL 1.93.0000 but in bootloader v0x32 is mentioned while it seems it should be v0x30 (as smae as my friends' Diamonds), anybody knows how can I fix it?
Regards
Darius

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.

good job...
moderator make this "sticky"

3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.

This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..

Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.

where can i read more information about jumpspl, how it works and everything?

eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.

sticky please
this needs to be a sticky topic.

losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.

Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.

Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)

donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.

losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..

Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.

Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?

Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...

Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me

bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi

herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.

Thanks Op
Managed to restore it no problem, but took ages