Related
I have downloaded the new Shipping ROM update from ClubImate.com (uni_cdl-me_11238_132_10301_ship.exe) and tried installing it onto my JasJar with a horrible result: it's now only good to use as a paper weight Initially everything looked fine; the ROM utility detected the device and correctly displayed the existing versions of CE image, Device Extended image and Device Radio image, along with the versions it was going to upgrade to. It reset the JasJar (what I'd think was erasing the current versions), but has since been unable to install the upgraded versions. Result: a (virtually) dead JasJar :evil:
I have done the following in order to try and get it up and running again:
1) Several soft and hard resets - the best effort is a screen (with no back light) saying 'Serial' at the top and 'v0.60' at the bottom.
2) Uninstalled ActiveSync and tried reinstalling both version 4.10 and 4.1
3) I have tried to complete the upgrade procedure on two different PCs; one running WinXP SP2 and Win2K SP4.
Despite these efforts, the ROM installation utility is unable to detect the device (ActiveSync's device detection has been dodgy from the word get-go, despite WinXP detecting it every single time - although saying it's unable to identify it) resulting in the following error message from the ROM Update Utility:
In the Dialog's title bar: "R:3030 D:21200 U:11000 P:857873 - CB1" and the message "Error 101: Connection Error".
Please, please, please (with sugar ontop); can anyone of all you clever people out there offer some help or hope?
Thank you very much :!:
sure you did hardresets?
You´re really stuck in bootloader? strange... if it happens to me, i just do the standard hardreset: keep the 2 softbuttons pressed, resest with the stylus, and the confirm with 0 (zero). did you do that?
Yup - really stuck
Yes, I'm afraid the normal hard reset (Soft keys+Stylus reset) followed by entering '0' to confirm the reset, only brings me back to the boot loader...
same here
Help?
I had the same problem once with my himalaya and it was due to a firewall and virusscanner.
I turned them off- Look in your taskmanager that there isn't still running a service in the background. then I reinstalled the update and tried i new hard reset.
This worked for me I hope it will help you too
Good luck
1. pres ctl alt sup
2. kill wcesMgr.exe and wcscomm.exe
3. Connect your jasjas
4. Now your bootloader must show USB in the screen
5. Run the upgrade.
It should works...
Good luck
here it is
http://forum.xda-developers.com/viewtopic.php?p=161210#161210
Dear oddball,
Did you find solution to your problem?
I have the same problem!
dherrero's solution did not work for me.
Hope to hear another solution.
Thanks
Sorted...
First of all, thanks a lot to everyone who tried to lend a helping hand (what an absolutely brilliant forum this is!!! ).
However, neither of the solutions suggested worked for me, as I after lots more trial and error, worked out that the problem had to be hardware related. And I'm pleased to say that fault wasn't in the JasJar; in fact it was down to an un-original sync cable :idea: ! I managed to lose the one that came with the device (along with the CD and everything else that was in the box ) and after consulting Club imate support, was (obviously wrongly) told that any standard min-USB cable would do the trick. Ordered a new cable from where I bought the JasJar, and hey presto, problem solved. ROM upgrade worked without a hitch on first attempt - I didn't even have to disable my anti-virus or fire-wall software.
It might not be the solution for everyone else who seems to be struggling, but it worked for me, so if you've run out of options, it's worth a go.
Again, thanks a lot - and good luck to those still seeking a solution.
I have the sam problem
CRAP cant work it out
Hi,
Had the same problem..
- flashing ROM said 100% successful, but after power+reset still got "serial v1.00"
- tried different ROMs, no luck
- tried power and hard reset, no luck
- then tried JasJar ROM again, no luck
- but then I tried the radio ROM flash and the power-reset brought it to life.
So I recommend trying
a) just the radio update first, if no luck
b) jasjar THEN radio
See how you go.
Michael
my mda pro is be gone (turn on)
thank for everyone!
my jj is in bootload three day!cannt turn on
today i just update firmware of xda exec,finished! i do soft reset !my jj is be come back!
now i try update to cht! good luck!!
now my jj is cht!
if you want to update lanuage :
1:download rom and rar a new folder
2:delet firmware file
3:use no_id.exe to update,
maybe 5min finished ,it is fast!
then kick -and- and reset (hard reset)
now become cht version!
good luck
Help Help, please, I need your help please,
I am really new to this forum. I have been reading a long time the forum, and see evolution of cooked rom. I love the Tomal version 8.2 19960 that was on my Jasjar Imate. When I try to put the Vanillla version 8.2 I think that I mismatch myself, and unfortunately I should get back when I saw the error code 120. What I did, I say yes, and now have a blank screen. Nothing happens. Badly again,again, I have seen before this message USB on top and 2.01 on the bottom, but after I pull out the battery and change for another, I cannot connect anymore the device to the computer. It gives me this message <USB device not recognized> or < Windows cannot recognize a device attaching to you computer>. I kept trying all times, and now that this message, I have on my computer.
I think I did break my device myself, or I have all my stuffs in it, my passwords, my agendas, my contacts and so on.
Howw can anybody help me get out of this mess and recover my device. Please, I need help. Your help please.
Gerard
Universal Imate JasJar broke after error code 120 - Message USB Device not recognize
Thanks to post already done in this forum. I searched and brwosed all <USB not recognized> installed many utilities but without success. Finally, I discover the post < Instructions for those stuck on Boot Screen (UNI_exitbootloader> in wiki.xda-developers.com and I get results, my device has been come to life again, it was RESURRECTED.
I follow exactly, that the solutions, I tried before, but in panic and in a hurry you could miss to steps and to pay attention to the instructions, but I retry again and again and finally it did work. And I put the Tomal 8.2 19960 again on my Imate jasJar and bingo, it works.
For sure, I have not seen the blue screen <clubimate> again, but a black screen, and at the bottom te version 1.15 radio, 8.2 TML and so on, but it doesn't matter, I am so glad to see all the functions come again to life, and put my sbp backup and bingo, I do have all my data and software back, as I take precautions allways to make a backup two days ago with sbp.
MANY THANKS TO XDA-DEVELOPERS; TO XDA DEVOPERS WIKI, AND TO THE PERSONS OR THE TEAM THAT FOCUS ON ANSWERS TO HELP PEOPLE LIKE ME AND OTHERS get out freely and sincerely to theirs problems.
I hope this post will help others to keep visiting and searching xda-developers for solutions of their device needs.
All the best
So..my phone is rather useless at the moment. Won't load the rom after freezing up while i slept last night. I go into bootloader and try to reflash but get the error "Invalid update tool" and it says something about a newer version. Has anyone had this error or know how to fix it? I am in desperate need of assistance here. Thank you for all replies in advance.
Edit: The exact error is as follows
Code:
ERROR[300]: INVALID UPDATE TOOL
This Update Utility cannot be used for your PDA Phone. Please get newer Update Utility.
I was running Kavana cooked rom 6.1.
I have tried to reflash with atleast 5 different roms and they all present this error.
Just checking, but did you try the default ROM for your device? If it is a T-mobile Dash, you will want to use one the the Tmobile stock ROM's first.
cswroe said:
Just checking, but did you try the default ROM for your device? If it is a T-mobile Dash, you will want to use one the the Tmobile stock ROM's first.
Click to expand...
Click to collapse
Yeah, I tried them and got the same error. Thanks, though.
OxR said:
So..my phone is rather useless at the moment. Won't load the rom after freezing up while i slept last night. I go into bootloader and try to reflash but get the error "Invalid update tool" and it says something about a newer version. Has anyone had this error or know how to fix it? I am in desperate need of assistance here. Thank you for all replies in advance.
Edit: The exact error is as follows
Code:
ERROR[300]: INVALID UPDATE TOOL
This Update Utility cannot be used for your PDA Phone. Please get newer Update Utility.
I was running Kavana cooked rom 6.1.
I have tried to reflash with atleast 5 different roms and they all present this error.
Click to expand...
Click to collapse
I know this might be a stupid question of me but, did you do a hard reset?
Why would you make another thread regarding issues with your phone, when you already have a thread going about problems with your phone?
Please post accordingly You should've posted this other issue on your previous thread, rather than making a new one! Can you imagine if everyone would make a thread for every little issue with their phone?
roloracer said:
I know this might be a stupid question of me but, did you do a hard reset?
Why would you make another thread regarding issues with your phone, when you already have a thread going about problems with your phone?
Please post accordingly You should've posted this other issue on your previous thread, rather than making a new one! Can you imagine if everyone would make a thread for every little issue with their phone?
Click to expand...
Click to collapse
It won't hard reset. I made a new topic because this is a completely different problem. I apologize if it was not necessary.
Bump.
Any ideas at all?
Ah yes.
My bomb didn't detonate until some time Wed/Thu night. 6am Thu morning I had to be at my local Polling Station where I was to be the 'Presiding Officer'.
Bad, bad timing.
Still, I managed a hard reset without the SD card in, (this took a few attempts), and having basic phone function, off I went to do my bit for European Democracy - honestly, the whole thing would be chaos without me ...
Anyway, I digress. I do that quite a lot. There was this one time ...
... I didn't get 'round to trying to sort it all out until Sat afternoon, (the phone, not the European Parliament), and as I have flashed this phone to buggery and beyond I expected it to take little time.
Ha. Ha. Ha.
I downloaded the latest version of the Energy ROM, (love it, love it, love it), ran the .bat file and; error 270.
I sparked up the bootloader and, of course, no connected device meant no update. I tried various 'stock' ROMs and got the same error you describe.
In UK, my provider is BT and there is no image link in the stickies, (I have finally found one, I will send a Mod a link), and tracking a full basic .exe image proved really difficult.
However, once found, all my problems evaporated.
So, find an executable basic ROM image from the phones' original provider, fire up the bootloader, run the .exe and a few minutes later you will be able to reflash.
Honest.
I believe you can also load the image as a .cab file onto the SD card and install from there but I didn't have to investigate this so can't promise anything. Sorry.
The ROM image is the key.
Once the bomb detonates, hard reset etc seems to become a bit flakey - keep trying.
I'm rambling again, aren't I?
Another beer I think ...
** Edit **
Yes, of course the BT ROM is now working.
Now I don't need it.
Ah well.
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
I have the same Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU value and i was able to restore my phone to working status with the following ROM
http://www.megaupload.com/?d=IJIVTIMF
Hope this help
10507
Thank you very much 10507! I'll download it now and see if it works.
Thanks for the file but it appears that it is for the SDA. It dit not work
luisro said:
Thanks for the file but it appears that it is for the SDA. It dit not work
Click to expand...
Click to collapse
That's odd, I was able to restore my Excalibur/Dash after flashing the corrupted EnergyRom.
Hope you will find a way to resolve your problem.
10507
But how did you do it? Flashing it through USB or through the memory card? The weird thing is that when I run the EXE the cellphone that appears in the picture of the program is an SDA. But well I will try it again and thank you for the help!
I used bootloader method and connected my phone through USB for flashing. Remember to remove your memory card when flashing.
well, I've been in your situation for almost 3 days now, and still no solution for it, maybe it's time to put it in the box and purchase a new one , all thanks to the broken EnergyROM ...
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
ookba said:
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
Click to expand...
Click to collapse
Thanks ookba for cheering us up. I'm having the same problem like many, many people in this forum hopeless seeing our dash not responding to every solution proposed in this forum and the only thing that we have right now is keep trying to flash and see if it works. I will try again in different PC and see what happens. I'll let all of you know if I finally resurrect my s621.
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
This problem is ridiculously weird to why some members are able to restore their phone to original factory condition, and others are not able. Therefore, I have search from trustworthy sites and from friends for difference made ROM. Hopefully, one of these ROMs with help out anyone...........
1.33.422.1 (Worldwide English, WM6)
http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
1.27.405.1 (Worldwide English, WM6)
http://rapidshare.com/files/100235639/HTC_S620_WWE_1.27.405.1.exe
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/104641948/T-Mobile_DASH_WM5_V_1.11.531.1.exe.html
Excalibur_BRIGHTSTAR_PTB_1.30.514.2_4.1.13.47_ 02.98.90_Ship
http://www.mediafire.com/?9gbwdzd2omg
Thanks 105507 but no success at all, I even found 2 more factory roms in the web and also they don't work. I own an unbranded international version s621 manufactured by Brightstar corporation (I tried to flash Brightstar's stock rom but it didn't work) and I noticed this because in the warranty docs it says brigthstar corporation and originally the phone came with WM5.
not that this will help. but this is one of the reasons why people should be really installing the hardspl so if you have a bad flash, you dont have to install a stock rom. any rom whether be it cooked or not will work. but this hardspl must be done prior to installing ANY rom. the hard spl is done by jockyw2001. send him a pm to see if theres anyway to get that on the phone, even in its current state.
edit: here's the link to the hardspl: http://forum.xda-developers.com/showthread.php?t=329605
luisro said:
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
Click to expand...
Click to collapse
My phone is the same your phone but ONBL 1.33.0000 and SPL 1.33.0000
I'm trying to find the original rom of this line but not found. Please help me!
Have you done a reset? My friend fixed his by trying reset a few times. He reset it, walked away...., it took long time to see whether it booted over; if not, do it again...
By the way, he leave the sim card in; and, you need to remove your micro sd card.
On an official site it is possible download ROM for your phone. It is flashing from bootloder mode. It some times helped me, while I have not flashed hard SPL.
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
Hi my friend, I wish you lucky!!!
by the way, where country you're from, I have some Shipped Roms here for brazilian Excalibur (S621), maybe it could help, if the answer is yes, let me know to made this one come to you
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Furious Girlfriend (oh My beloved Helloween died with my ROM's)
Boy oh Boy...
My ROM's are now in heaven
Girlfriend deleted they (I'm so sorry...)
But, pay attention in this thread
http://forum.xda-developers.com/showthread.php?t=381726
In there have a sort of shipped ROM's and maybe coud help you
Good luck my friends
A friend from XDA have some Shipped Rom's and will upload it for you, shortly he'll post something here
Hi,
experiencing a problem with my Xda O2 branded German Touch Diamond:
after switching on the WiFi the device rebooted itself and continued to reboot permanently until I remove the battery. Battery is full actually.
I flashed the original ROM successfully (previous one was a BliZZard custom ROM v5), but the device is still continues to reboot.
For warranty reasons I need to flash the original stock SPL back, but no success with this. I flashed it couple ot times and the flashing CustomRUU.exe showed success each time. But after prooving the SLP it still shows 1.93.Olinex.
I tried also any other HardSPLs like Olinex 1.37... again the same problem. 1.93.Olinex is showed on boot.
Any idea how to solve the flashing problem or maybe also any hint about the reboot problem?
I have important stuff on the 4 GB internal flash. How can I read the contets considering the above problem?
Any help highly apprechiated!
Cheers
same problemm
Same problem. Any help?
tekata said:
Hi,
experiencing a problem with my Xda O2 branded German Touch Diamond:
after switching on the WiFi the device rebooted itself and continued to reboot permanently until I remove the battery. Battery is full actually.
I flashed the original ROM successfully (previous one was a BliZZard custom ROM v5), but the device is still continues to reboot.
For warranty reasons I need to flash the original stock SPL back, but no success with this. I flashed it couple ot times and the flashing CustomRUU.exe showed success each time. But after prooving the SLP it still shows 1.93.Olinex.
I tried also any other HardSPLs like Olinex 1.37... again the same problem. 1.93.Olinex is showed on boot.
Any idea how to solve the flashing problem or maybe also any hint about the reboot problem?
I have important stuff on the 4 GB internal flash. How can I read the contets considering the above problem?
Any help highly apprechiated!
Cheers
Click to expand...
Click to collapse
Any chance to MTTY? Might help, just guessing...
Or try to flash a new radio ROM as the wifi hardware might be stuck in a state that is unknown to the drivers. Flashing a radio is supposed to reset hardware but I may be wrong.
Really guessing here but symptoms shows relation to radio hardware.
Cheers,
Cina.
sspl
You need to run sspl first before flashing to the stock SPL. I did had this same problem changing my HSPL before.
You can find the sspl on the olipro CID/Security/Sim Unlocker, I think.
Hello, my solution to this was conductive interconnect of metalic parts as you can see here
://i.ytimg.com/vi/UUnH8O-1jII/0.jpg
(of course with http on the beginning, i'm not allowed to post links)
on the left with aluminium tape (sorry for image quality, found it on web).
It also seems that the sim card reader has to be conductively connected with the above em shielding.
Hope it will help
it´s a battery problem ... get a different one and your phone should be fine
Dreamtheater2003 said:
You need to run sspl first before flashing to the stock SPL. I did had this same problem changing my HSPL before.
You can find the sspl on the olipro CID/Security/Sim Unlocker, I think.
Click to expand...
Click to collapse
Please correct me if I am wrong. But as far as I understood, it is only possible to SSPL the phone after running the system on it (e.g. inside windows mobile) and not from outside (e.g. USB connection or so). The problem is, that I cannot access win mobile at all! It is continuosly rebooting in an infinite loop. Not even able to see the windows mobile logo at start.
@cina
how do I MTTY the phone? any idea, link, tool? again: if I have to be "in the system" in order to check, whats wrong, then it will fail.
@edefux
Do you already had such a case? I am not sure, if buying a new battery is economical enough only in order to try, if it works. I admit, it could be the battery. But running the phone with the charger switched on, should show if its the battery or not. I tried with charger on, but obviously this didn't solve the problem. Or do you mean, that in the battery there is some sort of "short circuit", that's confusing the Diamond no matter if the charger is on or not?
@DiamondFlower
Thanks for the suggestion. I'll give it a try, when I tried everything else
This will be the final try before burrying the precious Diamond.
Cheerz
MTTY.
tekata said:
Please correct me if I am wrong. But as far as I understood, it is only possible to SSPL the phone after running the system on it (e.g. inside windows mobile) and not from outside (e.g. USB connection or so). The problem is, that I cannot access win mobile at all! It is continuosly rebooting in an infinite loop. Not even able to see the windows mobile logo at start.
@cina
how do I MTTY the phone? any idea, link, tool? again: if I have to be "in the system" in order to check, whats wrong, then it will fail.
...
Cheerz
Click to expand...
Click to collapse
See this post for MTTY. This is the second post on Diamond ROM thread pinned for easy access anyway. Please search before you post!
If you can enter bootloader mode with VolDown pressed while reboot you're off to go. You can plug in USB cable and you can flash SPL, Radio or any new ROM. I assumed this based on your first post:
tekata said:
I flashed the original ROM successfully (previous one was a BliZZard custom ROM v5), but the device is still continues to reboot.
Click to expand...
Click to collapse
Cheers,
Cina.
it is a battery problem i´m 99,9% sure of it - i had the same case ... it was driving me crazy ... different roms, radios, but the problem persisted - luckily at that time i was working at a cell phone provider and could try different hardware, which finally brought me to the solution to switch the battery.
edefux said:
it is a battery problem i´m 99,9% sure of it...
Click to expand...
Click to collapse
Maybe I'm a bit unlucky, but I've got the 0,1%. Took a new battery, this didn't solve the problem though.
i´m sorry it didn´t work for you ... !
it's ok! it didn't work - actually I could have thought about it wont work: beforehand I sent the item to the mobile operator guarantee team and they returned it back - no warranty of course (due to olinex bootloader which I wasn't able to remove) and stating: Fremdeinwirkung/ Totalschaden (total loss). And because I sent it without battery and they obviously checked it ... suppose with a fresh or "good" battery. And it still didn't work for them, so...
I'll try to open it and see if there is some short circuit around the metal shielding. Maybe I'm lucky then.
Anyway thanks guys about the hints and suggestions!
tekata said:
Please correct me if I am wrong. But as far as I understood, it is only possible to SSPL the phone after running the system on it (e.g. inside windows mobile) and not from outside (e.g. USB connection or so). The problem is, that I cannot access win mobile at all! It is continuosly rebooting in an infinite loop. Not even able to see the windows mobile logo at start.
Click to expand...
Click to collapse
I'm not sure if its called sspl but you can run it from boot loader and it will black out your phone. after that you need flash the new bootloader.
I'm thinking its not a bootloader problem though...