Develop Bugs

When installing WM6, ActiveSync auto disconects. What to do?

Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!

I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.

Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?

todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.

try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.

I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!

Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.

liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.

What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.

Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.

Very Strange Brick Problem

Hi guys, I've read and used the forum for years and upgraded my Cingular 8525 a ton without troubles (followed Vanx's method for vista and for upgrading), but this is the first time I'm really stuck without a clue.
I had Schaps latest OS on my phone working fine for about three days. It was charging with the USB hook up to my Computer. I pulled the USB out and the phone entered bootloader. I couldn't get it out. I tried using mtty to no avail, hard reset ect., but finally used the SD loading method to put TNT's latest on it (don't know why this worked). Here's the thing though, the phone will load fine on first load after I flash, but if I soft reset or turn the phone off and on it goes right into bootloader mode. The only way I can get it to load up again is to connect it to the computer's USB, take out the battery and then put it back in. the OS then boots up without fail.
I have read a ton and searched on the forum, and if any of you can help me understand what the hell I can do to fix my phone I would really appreciate it. I will post anymore info you guys would like, I really need your help on this one.
Thank you so much!

Hi,
I posted exactly the same problem today ! here:
http://forum.xda-developers.com/showthread.php?t=381284
It's really strange !
Dave

I've been reading everything and it appears that Schaps's new version seems to have this problem sometimes....I have the exact same problem as everyone else (mtty gives me the same results), and flashing a new rom doesn't get rid of it....I hope there is some way to fix this!
maybe I'll try flashing a new radio and see if that helps things....

I did notice that flashing Schaps 4.31 seems to include radio 1.50 and I had changed my anyway to 1.43 as I thought that was better for my area.
Not sure a radio will help. Maybe a different ROM version will ? Maybe 3.54 ?

I have flashed TNT's rom as well and it still has the problem now....I'm flashing a new radio as I type, I'm going to have to reflash the OS too, it just got stuck again as it was restarting.

Just a quick thing, I think I have solved my problem (not sure if it is permanent) by powering the phone off and on. Not resetting, just a simple power off. I spoke to a colleague who said the way it shuts down is different to soft reset (makes sense) and I haven't powered my phone off properly for a long time.
I have tried soft reset a couple of times since doing this and it hasn't gone to the bootloader screen once.
Maybe this is the simple fix.
I will keep you posted.

try to flash OFFICIAL ROM first , maybe there are few bug / missing file when error appear while flashing other ROM.
I hope it will help you both.
rgds,
ermen

Use mtty to see if yo have any bad blocks... I've had a few problems the same as yours and found I had 1 or 2 extra bad blocks, after the 2 "factory standard" bad blocks I got on my jasjam of course. hope this helps...

My fix didn't work.
Not sure what I am suppossed to see when I run "task 2a".
Has anyone had any luck fixing this ?

Need hepl guys PLEASE

Hi, i have been trying for the last month and a half to try another rom on my hermes,but it seems i can't.
i have flashed many Roms and i never had a problem in doing that till the las time when i tried to flash into the new S64.
every time i try flashing into any new rom it rejects me by giving me the (ERROR 260) telling me i'm not connected and the USB cardle thing, but all of my connections are correct and my ActiveShyn is up to date and i was always flashing roms in the same way.
Some seniors here when i have mentioned that told me that it seems i have flashed or reflashed the Hardspl, so i'm trying to reflash the Hardspl, i have tried endless times but it keeps telling me the same althought i have downloaded almost every hardspl that is available in the xda site lol.
what i'm requesting please if possible to direct me in the steps that i need to make my hermes functional again please i'm sure u understand what i'm saying.
some have mentioned that cause i still have the
herm100 i can't flash it into another roms but that sounds a bit strange lol.
I know that i have still herm100 (old) and my ipl-1.01
and spl-1.06 but i think that dosn't matter in my opinion.
Please i request if u can help me in fixing my problem by providing me the steps by simple words and if you have a fresh zips of hardspl coz i'm so confused which one to use, it would be nice to hear how to do it step by step.
i really need your support and excuse me if i'm bothering u with this kind of request but i didn't know where else to go and ask.
My Current rom is the HTC_Hermes_S64_WM_6[1].1_HTC_WWE_v2_30.03.2008 which is old and i would like to refresh my phone by a new version.
i was thinking of the new HTC_HERMES_S64_WM_6.1_TouchFlo2D_UC_ WWE v3 / GER v1 but i don't know if it would work on my herm100 cause i was told it was designed for herm200 and abouve is that true?
If not well there are so many more roms out there i would like to try but i'm stuck for the moment.
please again i wouldn't have bothered u with my request if i wasn't facing this problem.
thank u a lot and i hope to hear soon from u commrade.
Dayhauck.

have you tried to manually go into the bootloader and flash? You don't need activesync to flash like that if you're connected with USB. Also, from your SD card. Both have worked for me in the past.

Though you should have Hard SPL installed if you want to use the sd card method.

i have tried to do it manualy but i not much of a luck in loading the Hard SPL.
I really don't know what to do. i can't even f;ash to the original htc rom .
what else can i do?

1. Check your usb cable.
2. Try different USB ports in ur PC,
3. Check if the mini USB in Hermes is not damaged.
4. Check the bootloader if you have HardSPL installed.
5. Try SD method,
6. Read the wiki.

check out post 1160 on page 116 of this thread for sd card method for Hard SPL V7 - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...

I had the same problem. If you can activesync with the cable then all you need to do as already mentioned above.
With the phone attached manually go into bootloader (hold on/off on right of phone and 'ok' on the left of phone both in while you prod the phone reset at the bottom of the device).
When you have the multicoloured boot loader run the update and it should work fine.
Hope this is some hepl

Energy ROM semi bricked my Dash, help needed! (And appreciated)

Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!

I have the same Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU value and i was able to restore my phone to working status with the following ROM
http://www.megaupload.com/?d=IJIVTIMF
Hope this help
10507

Thank you very much 10507! I'll download it now and see if it works.

Thanks for the file but it appears that it is for the SDA. It dit not work

luisro said:
Thanks for the file but it appears that it is for the SDA. It dit not work
Click to expand...
Click to collapse
That's odd, I was able to restore my Excalibur/Dash after flashing the corrupted EnergyRom.
Hope you will find a way to resolve your problem.
10507

But how did you do it? Flashing it through USB or through the memory card? The weird thing is that when I run the EXE the cellphone that appears in the picture of the program is an SDA. But well I will try it again and thank you for the help!

I used bootloader method and connected my phone through USB for flashing. Remember to remove your memory card when flashing.

well, I've been in your situation for almost 3 days now, and still no solution for it, maybe it's time to put it in the box and purchase a new one , all thanks to the broken EnergyROM ...

Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.

ookba said:
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
Click to expand...
Click to collapse
Thanks ookba for cheering us up. I'm having the same problem like many, many people in this forum hopeless seeing our dash not responding to every solution proposed in this forum and the only thing that we have right now is keep trying to flash and see if it works. I will try again in different PC and see what happens. I'll let all of you know if I finally resurrect my s621.

Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems

luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
This problem is ridiculously weird to why some members are able to restore their phone to original factory condition, and others are not able. Therefore, I have search from trustworthy sites and from friends for difference made ROM. Hopefully, one of these ROMs with help out anyone...........
1.33.422.1 (Worldwide English, WM6)
http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
1.27.405.1 (Worldwide English, WM6)
http://rapidshare.com/files/100235639/HTC_S620_WWE_1.27.405.1.exe
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/104641948/T-Mobile_DASH_WM5_V_1.11.531.1.exe.html
Excalibur_BRIGHTSTAR_PTB_1.30.514.2_4.1.13.47_ 02.98.90_Ship
http://www.mediafire.com/?9gbwdzd2omg

Thanks 105507 but no success at all, I even found 2 more factory roms in the web and also they don't work. I own an unbranded international version s621 manufactured by Brightstar corporation (I tried to flash Brightstar's stock rom but it didn't work) and I noticed this because in the warranty docs it says brigthstar corporation and originally the phone came with WM5.

not that this will help. but this is one of the reasons why people should be really installing the hardspl so if you have a bad flash, you dont have to install a stock rom. any rom whether be it cooked or not will work. but this hardspl must be done prior to installing ANY rom. the hard spl is done by jockyw2001. send him a pm to see if theres anyway to get that on the phone, even in its current state.
edit: here's the link to the hardspl: http://forum.xda-developers.com/showthread.php?t=329605

luisro said:
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
Click to expand...
Click to collapse
My phone is the same your phone but ONBL 1.33.0000 and SPL 1.33.0000
I'm trying to find the original rom of this line but not found. Please help me!

Have you done a reset? My friend fixed his by trying reset a few times. He reset it, walked away...., it took long time to see whether it booted over; if not, do it again...
By the way, he leave the sim card in; and, you need to remove your micro sd card.

On an official site it is possible download ROM for your phone. It is flashing from bootloder mode. It some times helped me, while I have not flashed hard SPL.

luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
Hi my friend, I wish you lucky!!!
by the way, where country you're from, I have some Shipped Roms here for brazilian Excalibur (S621), maybe it could help, if the answer is yes, let me know to made this one come to you

http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard

Furious Girlfriend (oh My beloved Helloween died with my ROM's)
Boy oh Boy...
My ROM's are now in heaven
Girlfriend deleted they (I'm so sorry...)
But, pay attention in this thread
http://forum.xda-developers.com/showthread.php?t=381726
In there have a sort of shipped ROM's and maybe coud help you
Good luck my friends
A friend from XDA have some Shipped Rom's and will upload it for you, shortly he'll post something here

[TOOL] Task 29 (format internal Memory) without drivers, without mtty-It's about time

Hi all, for all the people like me who do not have the patience or knowledge do adventure themselves in the mitty thread.
This program already exists for X1, HD2, TP2 (for what I know) and I have tested it and it works.
After some search on this forum I have talked to agent_47, who was kind enough to make a task29 program for our HTC Diamonds (GSM version).
Agent_47 or me do not take any responsibility for ay damage done to your device. Use it at your own risk, and only after you have HSPL already installed on your device.
Do not know what a HSPL is, check here:
http://forum.xda-developers.com/showthread.php?t=415191
agent_47 said:
it will flash radio 1.09.25.23
replace the radio if u want to use other version
Click to expand...
Click to collapse
agent_47 said:
now we can mtty our "HTC Diamond" without having the need of MTTY and its drivers
INSTRUCTIONS:
- download and unzip
- run then ROMUpdateUtility.exe and wait for it to finish.....
- device will reboot but will neva go past the bootscreen coz there is no OS to boot
- take our batti and then flash a rom using mSD card or by taking device into bootloader and using customRUU to load ur favorite ROM
DOWNLOAD:
http://rs604.rapidshare.com/files/407049148/task29-diamond.7z
WHATS TASK29\MTTY
when u flash a rom, you are copying files onto the internal memory (like duh!) but if u repeatadly flash different roms, sometimes files from older version stays behind as when u flash a rom, you just copy and sometimes overwrite files without deleting the older ones. hence at times these older files may create bugs\instability. hardrest donot always fix it.so we use MTTY
but the thing is, mtty is and can be hard to use for new users. ... for me,, i was having the worst time installin the drivers needed to run mtty on win7 x64. so u i made this tool for me and for all
CREDIT:
all credit goes to doloop for coming up with the idea
Click to expand...
Click to collapse
and I would add to agent_47, as he adapted this tool for the HTC Diamond

Did anyone tried this?
What's the verdict?

mmm. interesting.

Thanks for the share and all your hard work but this is actually harder than mitty for me and i am a windows 7 user also

wapvirus said:
Thanks for the share and all your hard work but this is actually harder than mitty for me and i am a windows 7 user also
Click to expand...
Click to collapse
I do not understand how this is possible, I am using Vista and this is as easy as flashing a ROM with a computer. You just connect the device via USB to the Diamond, let active sync finish. Then you just need to run "ROMUpdateUtility.exe" and follow the instructions.
I have tested this, and I can confirm this is working for the European HTC Diamond (bought in Portugal).
This was not made by me, but I do think that more people will benefit with this program. Hopefully people will overcome the initial resistance to change.

Great idea!
I used to MTTY through VMWare Windows XP x86 within my host Windows 7 x64. It was a pain in the ass to get though but it always worked for me. This is a great time saver!
Regards to both of you Johev and agent_47!
Willing to test on my next flash.
Best regards,
Cina.

INSTRUCTIONS:
- take our batti and then flash a rom using mSD cardor by taking device into bootloader and using customRUU to load ur favorite ROM
Click to expand...
Click to collapse
What do you mean? take out battery?
Gonna try this with my next flash

Yeah, the sentence is a bit odd to me to
i asume it means take out battery but still..
i'm not gonna try it until i know it for sure!
--edit--
i couldn't help it and used it anyway..
i assumed "take our batti" means take out battery cuz it worked for me!
my diamond was clean (i guess) and i'm now enjoying a new rom!
Thanx guys!!

I would never post something that I did not test first.
I am glad that you liked it, and I really think it is much simpler then the mitty thread.
Good luck flashing.

rapidshare
first would like to give thanks for sharing this one but some people cannot use rapidshare links and unluckily I am those few
can you give alternative link like mediafire ????

character said:
first would like to give thanks for sharing this one but some people cannot use rapidshare links and unluckily I am those few
can you give alternative link like mediafire ????
Click to expand...
Click to collapse
http://www.mediafire.com/?jabdu2n968xa9uk here you are

I LOVE THIS TOOL
this isn't good for my ORD.. i'm flashing the hell out of my diamond now!
Getting a HD2 in about a month.. can't wait for it ;D

I tried it, but I only get the start screen with "Touch diamond", no bootloader.
But I´ve installed HARDSPL Olinex, because I already flashed other ROM´s.
How can I solve this problem?
What about battery? When I have to get it out, when I can put it in again...?
fibula

to get into bootloader you have to reset your device while holding the volume down button!
then you will get the tri-color screen,
connect your diamond to your pc and flash a rom with a RUU!

fibula said:
I tried it, but I only get the start screen with "Touch diamond", no bootloader.
But I´ve installed HARDSPL Olinex, because I already flashed other ROM´s.
How can I solve this problem?
What about battery? When I have to get it out, when I can put it in again...?
fibula
Click to expand...
Click to collapse
To get into bootloader with my diamond:
1) Turn Diamond off, take out battery for 5 seconds.
2) Put battery back inside, and press and hold the centre button (circle) and turn ON the device (hold both buttons) until you see a 3 colour screen
If step 2 does not work, try pressing holding volume down while turning the device on (hold the ON button too). Remember to take out the battery before you do this.
Hope this helps.

Hi!
Does this work by simply copying any ROM's nbh file (instead of radio*.nbg) to folder and executing ROMUpdateUtility.exe? Will it MTTY before flashing the ROM?
Currently I'm trying this method out. It is around at 50% of flashing progress.
I'll report back.
Cina.

thanks a ton dude.... magnificent work...

Now if there were only a way to do it directly from Internal Storage, without RUU...

It does not work the way I described. It hangs on HTC Diamond black boot screen and no red lines appears in lower right corner (no OS recognized).
So you have to flash 2 times. Radio flash is shorted for the first attempt and on the second turn you flash your ROM with CustomRUU.
There is a similiar tool like this with the method working with other devices I described above. FlashaholicRUU. Someone give it a try for Diamond. Next week I'll do it and report back.
Cheers,
Cina.

cina said:
It does not work the way I described. It hangs on HTC Diamond black boot screen and no red lines appears in lower right corner (no OS recognized).
So you have to flash 2 times. Radio flash is shorted for the first attempt and on the second turn you flash your ROM with CustomRUU.
There is a similiar tool like this with the method working with other devices I described above. FlashaholicRUU. Someone give it a try for Diamond. Next week I'll do it and report back.
Cheers,
Cina.
Click to expand...
Click to collapse
I remember to see that post on xda developers front page short time ago, but I was not sure if it would work for HTC Diamond.
A universal task29 that would format and flash the device in one single process.
Ironically it was developed a few weeks after I have found an alternative way to mitty that I posted here.
So far I did not hear that it was compatible with Diamond, so I will not risk it.
It's nice to have all these options, because when I searched for something like this a few months ago, I could only find the mitty threat that has more than 80 posts.
For me it was strange as newer devices with very similar hardware and software already had something like this, but Diamond users had to use mitty.
Well I am glad that you like it, and hopefully I helped someone that was not able or willing to do it manually.