two days a go I tried to upgrade present WM5 to WM6! few moments after it appeared recovery error. I followed an instruction, but the device was crashed! next time when I tried to start device, on the screen appears HTC and then stops. So many times I attempt to repeat process of upgrading, but nothing. What have I to do! Please help me?
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Related
two days a go I tried to upgrade present WM5 to WM6! few moments after it appeared recovery error. I followed an instruction, but the device was crashed! next time when I tried to start device, on the screen appears HTC and then stops. So many times I attempt to repeat process of upgrading, but nothing. What have I to do! Please help me?
Hi,
I tried many times to install the hard spl version 1.34 on my new Diamond, but I have always the same problem:
- the program start
-it run since the boot loader mode appear on the screen
-then appear the progress bar and then ..... NOTHING.
I'm not new to flash and add new software, infact before the Diamond I had a Trinity flahed many and many times (Kaiser, Elegance Edition, etc....).
What can I do to solve the problem ? Really I don't undestand.
Please If someone has solved the problem post the solution.
Thank's
Post your SPL upgrade procedure, step by step.
We'll try to see where you might've gone wrong.
Did you sync your diam with active sync?
Did you try the spl-manual?
Maybe it is also good to give a link to the post you got the SPL from, so we know exactly which version you have (signed/unsigned).
I could not do it on my macbook pro either. IN teh end I resorted to boot camp and it worked fine
The procedure I made is still the same.
1. connect to activesync
2. start the exe
3. the screen of the diamond star the boot loader mode
4. appear the progress bar both in the pc screen and the diamond screen
5. the procedure stops and no data are transferred to the diamond
I tried all the three version of hard spl but the problem is still present.
The version of hard spl (from 1.24 to 1.34) is the one you can find in the first page of the forum.... belive me I did it many times in the past and I read very well the procedure suggested in the post.
However I will try to use boot camp.
Thank' s to everibody .
Dear Sir
My diamond got stuck up at the welcome screen or else in the alignment screen. I've flashed many roms number of times before but this time this happened after a hard reset- using Macadam 1.2 (latest).
My bootloader reads - Diam140 MFG 64M; SPL-1.40. Olinex. After this I've flashed back to the latest indian stock rom i.e. First to (RUU_Diamond_hTC_Asia_India_1.93.720.4_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_ShiP) but know result & (RUU_Diamond_hTC_Asia_India_1.93.720.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.07_Ship_R). After going through the forums- I understood that I've to step down to stock spl. But even after successful flashing, the boot loader shows the same- "SPL-1.40.OliNex".
I'm unable to use the jump SPL, because I can't pass through the alignment screen. Please help, is there any way to JUMP SPL without operating the phone.
Or else how can I come back to the stock spl.
Please Help.........................
Regards
Furthermore, I've tried using mtty to following the procedure:
Correct sequence is as follows:-
1. Launch ActiveSync on PC
2. Go to connection settings
3. Uncheck the Allow USB Connection
4. bring the device to bootloader. AND connect to the PC.
5. Now, run mtty1_1_.42_538 on PC.
6. CMD>task 29
7. Flash the ROM of your choice
Then flashed the stock rom again. But the problem remained.
jockyw2001 - suggested me on PM to do- "in mtty: set 16 0 then reboot'- but nothing happened. Or I didn't follow the correct steps... can anyone explain & help please....
[UPDATE]where do I get the commands for mtty
Can anyone tell me the link where I can get the commands to be used in mtty... Is there anyway to bypass the screen alignment part during start up after a hard reset.... how can I JumpSPL in a handset where the touch screen is not working.. but the screen is not completely dead, i.e. on tapping the "+" sign is moving after around 5 or 7 mins of the tap...
Please help guys.... I'm waiting to be rescued by some WM wizard from this great community.....
Regards
wizards- all'r failing or what- very few people with clear funda
cmonex please help....
hi man
i had the same problem, with all the rom around
than i understand that the problem was the radio rom
try to flash the lastest radio..i use the 1.13
Flash a Rom without screen alignment
Hi
If you on bootloader and you have 1.40olinex then flash a 1.13 radio then flash a Rom without Screen alignment process. It might help. Good luck
Every time I try to update the hardspl on my phone it works up until its about to install. The progress goes 0 percent on my comp and stays there then the loading icon comes up on my diamond but then it just freezes and disconnects from my computer then gives me error 260. I'm on xp and I have followed all the instructions and its pissing me off.
Error 260
I've had this same problem too.
Plucked up the courage to install unsigned hard SPL Olinex 1.93, so I could just install the 2.03.405.3 official HTC ROM (Orange haven't bothered to release it...).
And then this error 260...
At first I thought I'd bricked my Diamond, but luckily a soft reset brought it back to life.
I've trawled this site, and it doesn't seem like anyone has any solutions to this issue.
So, at the moment, my upgrade process has stalled.
Any advice, gratefully received!
Dear xda-dev community!
Today I tried to flash a wm6.1 ROM on my Uni. In the first few percents of the flashing process everything went fine, however, at 9% it reported some error, and stopped flashing. Now I can't boot back to wm, but I can enter bootloader, though every time upgrading fails at around 9%. Have I bricked my uni? thanks in advice, andor
andor44 said:
Dear xda-dev community!
Today I tried to flash a wm6.1 ROM on my Uni. In the first few percents of the flashing process everything went fine, however, at 9% it reported some error, and stopped flashing. Now I can't boot back to wm, but I can enter bootloader, though every time upgrading fails at around 9%. Have I bricked my uni? thanks in advice, andor
Click to expand...
Click to collapse
Please forgive me for being inpatient, the DOC Format method solved the problem. Please delete/merge this topic to a ''general help'' topic.