Related
Hi y'all,
i have a BT GPS receiver that i used with my Qtek 2020 (before this was stolen... ).
Now i have a XDA Exec from O2, but i am not able to set the receiver!
Anyone has any tip for me?
Thanks a lot...
...no one can help me out...??? Please...
Check out this guide and follow from after installing tomtom and you should get BT GPS working with exec, I did!!!
ps search term used was 'tomtom 5.1 guide'
hope this helps!
http://forum.xda-developers.com/viewtopic.php?t=28386
Hello,
first the bad news: not every bt-reciever is working...
but you should try this way:
Connection-Manager
Enable BT
Setting (Connection-Manager) BT-Settings
Tab devices and ad new partnership (be sure, BT-Reciever is on)
Pair it with your Universal (pin is usuall 0000)
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Now it should work!
Thanks for the tipo...now i don't have my GPS receiver with me...but tomorrow i will give it a try.
The only thing that i find strange is: when i try to set the outgoing port i find my BT receiver in a box, but when i try to set the incoming port i dont' find it anywhere.
Something wrong?
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
can anyone confirm if haicom-405 bt works with dopod 900?
Hustladave said:
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
Click to expand...
Click to collapse
As I wrote before:
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Best wishes
Teja
jona69 said:
can anyone confirm if haicom-405 bt works with dopod 900?
Click to expand...
Click to collapse
I follow the tips ...outgoing port (COM4 - which the only port can be used other failed to open), incoming port (COM8).
But it doesnt work with my Garmin10 .... which work well with my previous XDAIIs. Anyone use Garmin1o with Dopo900?
Thanks
Usually, there's no need to setup an ingoing COM port: my Holux 236 receiver, for instance, works perfectly paired with my Qtek 9000 and only the outgoing COM8 setup'd.
The only thing to pay attention for is that TomTom have to be v5.1 or above (better if v5.21), in order to work properly under Windows Mobile 5.0.
Well...in my previous XDAII worked perfectly using the software MAPSONIC and the GPS VIEWER with my BT receiver (and just setting the outgoing port).
I tried to do like Teja told me in his answer (setting the outgoing COM4 and the incoming COM8), but it still does not work.
I will try to get a TOMTOM 5.1 software to give it a try...
solved...and i don't need to setup the ingoing port...thanks for the tips
Hi there! I have MDA Pro from T-mobile (UK) and until now I couldn't set a COM port appart of COM0 port for BT-GPS...
Now have COM4 for outgoing port and tom tom once is connected after 5 seconds is disconnected and again after 5 seconds is connected and again is disconnected and again......
I am using TT 5.21
Help please
I have set the outgoing port on COM8, no ingoing port needed and it works fine...although i don't have TOMTOM!!!
Orange M5000 and BT GPS and TOMTOM 5.21
I thought I share this just in case there are other like me out there.
I had an Orange M2000 with tomtom 5.0 and 512MB SD card.
I installed TT5 as normal on the PDA but the maps on the 512MB SD card.
I just got an Orange M5000 which is XDA EXEC and could not install TOMTOM 5.0 from CD. The SETUP kept on crashing on XP PC.
Here is the solution:
1) Put the SD card with the maps in M5000
2) Did NOT install TT5 from CD but downloaded navupd521.exe from the tomtom site and installed this on M5000 fine.
NOTE: I did not have to copy CAB files. I just installed this as normal from my PC with the USB cable
3) TT installed fine but I could not get it to recognise the BT GPS
I used the instructions below from the forum:
a) Turn on BT GPS
b) on PDA goto BlueTooth seeting --> New Partnership and supply the password (0000) to pair it.
c) Then in Bluetooth settings select the COM PORTS tab
d) Select Incoming port and set to COM8
e) and again in COM PORTS tab select Outgoing ports and select COM4
f) Start TOMTOM and goto Preferences and find GPS Configuration and select OTHER GPS and select COM4
It works every time... ALL my FAvourites etc are still there so no need to type them again.
So far WM5 and TT5 rocks. I will be testing it on the road with my Plantronics BT headset soon. With my old M2000, usually when TT5 is on the M2000 CPU does not have the juice and Bluetooth devices die or stop responding. Also when I stopped TT5 application the BlueTooth stopped.
We will see how M5000 improves on M2000
Thax...
i believe you shouldnt have a problem running your headset and bluetooth GPS together.
when i had a blue angel i ran TT3 with my SonyErricson Car Kit and the TT3 together and made vioce calls at the same time and even now with the Universal i can do the same! run them both together!
only thing is that occasionaly the TT5 seems to be a little behind my actual location if i have made/received a call luckily by only 30-40 yards so can still use the screen to see where my turnings are.
has anyone else found that and got the cure....
thanks
Hi all, for the last few months I have tried various Universal ROMs and even various WM5 phones including HTC and HP iPAQ, there are some commond issues which I haven't been able to figure out a permanent solution (work arounds are available though not ideal), these are:
- SIP (System Input Panel), if you install any additional SIP like SPB fullscreen keyboard, Monster SIP etc, every time after you soft reset the device, unless you load them up straight away, you will not be able to load them up after a few minutes (don't know exactly how long) until next reset!! This is a great pain, I have found a SIP changer program which automatically load a SIP after soft reset, but I will really love a permanent solution.
- Bluetooth problem with Tomtom 6 (TT6). With lots of AKU versions of WM5 (apart from Helmi AKU 3.3 I tried so far, haven't tried it with Helmi AKU 3.5 though so I can't be sure with that version) every time I start up TT 6 it asks me to enter the passcode to pair my BT GPS receiver again even though I have done it 100 times already!! Again I have seen this issue on other WM5 devices in addition to Universal so I am wondering if any one has a solution.
Thanks!
kevin.jiang said:
- Bluetooth problem with Tomtom 6 (TT6). With lots of AKU versions of WM5 (apart from Helmi AKU 3.3 I tried so far, haven't tried it with Helmi AKU 3.5 though so I can't be sure with that version) every time I start up TT 6 it asks me to enter the passcode to pair my BT GPS receiver again even though I have done it 100 times already!! Again I have seen this issue on other WM5 devices in addition to Universal so I am wondering if any one has a solution.
Click to expand...
Click to collapse
I've never seen this problem on either my Universal, or my friend's Wizard (which I set up for them).
I don't know if this is the "standard" way, but basically, I pair the GPS device (a BT-77 in our cases), and then setup an outgoing COM port to it, and then simply tell TomTom to attach to that COM port. In fact, I have two BT-77s, one set to COM0 in the car, and a hand-held one on COM4, and I can switch to my heart's content, and have never been asked to re-pair.
Cheers,
Steve.
kevin.jiang said:
- SIP (System Input Panel), if you install any additional SIP like SPB fullscreen keyboard, Monster SIP etc, every time after you soft reset the device, unless you load them up straight away, you will not be able to load them up after a few minutes (don't know exactly how long) until next reset!! This is a great pain, I have found a SIP changer program which automatically load a SIP after soft reset, but I will really love a permanent solution.
Click to expand...
Click to collapse
I know many SIP can not be able load out. Did you solve this? or how to load them with permanent solution?
kevin.jiang said:
I have found a SIP changer program which automatically load a SIP after soft reset, but I will really love a permanent solution.
Click to expand...
Click to collapse
i've installed a hebrew sip but i dont have a problem loading it anytime i want.
although, sometimes i have a problem composing a new text message. the device gets stuck sometimes if the keyboard it not opened when i click "new".
happends only with helmi's 3.5 and with the hebrew keyboard. doesn't happen with default SIPs.
whats te program you found to load the all the SIPs?
is it "SIPz"? (from the same maker of PQz).
I have the same problem with blue thooth and CoPilot I use. The software is iGo. I tried several roms, but after I switch off the GPS and switch it on, it always wants to pair with Uni again.
StevePritchard said:
I've never seen this problem on either my Universal, or my friend's Wizard (which I set up for them).
I don't know if this is the "standard" way, but basically, I pair the GPS device (a BT-77 in our cases), and then setup an outgoing COM port to it, and then simply tell TomTom to attach to that COM port. In fact, I have two BT-77s, one set to COM0 in the car, and a hand-held one on COM4, and I can switch to my heart's content, and have never been asked to re-pair.
Cheers,
Steve.
Click to expand...
Click to collapse
Thanks for the suggestion Steve, I have indeed paired the BT GPS receiver, created the outgoing port as COM4 (actually I also tried other available ones) and point TT6 to it. I have been using this BT GPS receiver for over 2 years with various devices including my good old HP iPAQ H4150. This problem didn't happen with my Universal's original Orange SPV M5000 ROM and it doesn't happen with Helmi's AKU 3.3/3.5 ROM either which is the main reason why I am using AKU 3.3 now.
I have this problem on JWright's i-mate AKU 3.2 ROM, my wife's HP iPAQ rw6828 (WM5 AKU 2.3), my friend's T-Mobile MDA Vario II (HTC Hermes, WM5 AKU 2.3).
vuquan said:
I know many SIP can not be able load out. Did you solve this? or how to load them with permanent solution?
Click to expand...
Click to collapse
No good solution and I am wondering if anybody else knows how to solve it. I have tried hacking the registry to make my additional SIP default and I ended up with my universal not being to boot until a hard reset. The work around is this SIPChange attached, basically you set which one you want as default, then every time you soft reset it loads that SIP automatically before it becomes impossible to load it.
kevin.jiang said:
Thanks for the suggestion Steve, I have indeed paired the BT GPS receiver, created the outgoing port as COM4 (actually I also tried other available ones) and point TT6 to it. I have been using this BT GPS receiver for over 2 years with various devices including my good old HP iPAQ H4150. This problem didn't happen with my Universal's original Orange SPV M5000 ROM and it doesn't happen with Helmi's AKU 3.3/3.5 ROM either which is the main reason why I am using AKU 3.3 now.
I have this problem on JWright's i-mate AKU 3.2 ROM, my wife's HP iPAQ rw6828 (WM5 AKU 2.3), my friend's T-Mobile MDA Vario II (HTC Hermes, WM5 AKU 2.3).
Click to expand...
Click to collapse
I've not had the problem with either of the O2 ROMs, and Ivan's AKU3.5 test ROM - I haven't tried any other ROMs. I unticked the "secure connection" - not sure if that's relevant or not.
I found that only COM0 and COM4 seemed to be available for outgoing ports.
Before you go into TT6 - is the GPS device in the device list, along with the outgoing port set up correctly? Do you switch BlueTooth on and off? I have it on all the time - I'm just trying to think of things that might be different in our configs.
Cheers,
Steve.
I have both TT6 and iGO 2006 on my XDA Exec. The TT6 (and TT5 before that) always worked well with the BT-77 by simply pairing the GPS to the XDA EXEC on a COM port and selecting that COM port in TT6.
With iGO 2006, on the same XDA EXEC, it will ask to pair the BT-77 every time I launch iGO 2006. The only solution I could find was to use Franson's GPSGate to create Virtual COM ports for the BT-77 and to select this virtual COM port in iGO 2006.
StevePritchard said:
I've not had the problem with either of the O2 ROMs, and Ivan's AKU3.5 test ROM - I haven't tried any other ROMs. I unticked the "secure connection" - not sure if that's relevant or not.
I found that only COM0 and COM4 seemed to be available for outgoing ports.
Before you go into TT6 - is the GPS device in the device list, along with the outgoing port set up correctly? Do you switch BlueTooth on and off? I have it on all the time - I'm just trying to think of things that might be different in our configs.
Steve.
Click to expand...
Click to collapse
Thanks for the advise, I have tried unticking "secure connection" as well and it didn't help.
From what I am gathering in the information supplied it looks to be caused by a combination of the BT GPS receiver, the WM5 and the Sat Nav software.
I can't remember what make and model my BT GPS receiver is because I bought it over 2 years ago and back then I didn't care what model it is. Now that I can't tell it from looking at the outside of this thing.
This is a wierd problem as with different combination of the GPS reciver, WM5 and software it may or may not happen. What I was having that problem using Tomtom 6 I tried the GPSInfo shareware and it didn't ask me to pair every time. Very strange, anyway I am alright now with Helmi's AKU 3.3 using COM5 as the port with my good old BT GPS receiver and TT6.
kevin.jiang said:
No good solution and I am wondering if anybody else knows how to solve it. I have tried hacking the registry to make my additional SIP default and I ended up with my universal not being to boot until a hard reset. The work around is this SIPChange attached, basically you set which one you want as default, then every time you soft reset it loads that SIP automatically before it becomes impossible to load it.
Click to expand...
Click to collapse
Thank you so much! it work on my device.
Hi chaps,
Excuse what might seem like a stupid question from a newbie...but....got my new Orbit a couple of days ago....and straight away, the problems came in thick and fast!!
Has anyone successfully set one of these things up to Activesync via bluetooth??? Mine is stubbornly refusing to do so...
Also...my FM radio plays nothing but Simon and Garfunkel, since all I get is "The sound of Silence" Nothing....zip...zero is being played
It spat on my TomTom's auto install, until I handraulically installed the cabs, must say, this sat nav is head and shoulders above the same software on my old XDA II, using a wired GPS Antenna...nice
Anybody any ideas (I spent 2hrs on the phone with O2 about the bluetooth this week, and they just put their hands up in the air!!)
Nice site btw
Neil
Why not trying this here:
http://www.dpicts.com/axim/
Bluetooth Activesync works ok using the Microsoft XP SP2 stack instead of Widcomm or Toshiba:-
http://forum.xda-developers.com/showthread.php?t=288761
I tried and failed with Widcomm, but got it working 1st time once I used the MS stack.
Had the same problem with Tomtom. For me it was because my version of tt (5) was for an older version of WM. Installer didn't work, but manually dragged cabs were fine. I suspect tt6 installs fine.
F.
Mine is WIDCOMM, how to I get it to run the MS stack?
works fine with Toshiba, and the older versions of widcomm.
Toshiba stack always has an incoming port on com 7
set this and it will work fine (make sure you have the latest version of the stack from http://aps.toshiba-tro.de/bluetooth/pages/download.php)
Not tried with the latest versions cos my MIS key runs bluesoleil :-(
Try this
open my bluetooth places.
click bluetooth at the top of the windows (next to file, edit etc.)
click advanced configuration
click local services
note the port associated with the bluetooth serial port service.
open activesync on the pc
click file
click connection settings
set the com port here. (it must be lower than 20 for activesync 4.x)
click ok
open activesync on the device
tap menu
tap connect via bluetooth
tap yes when it asks about creating a pairing.
tap new device (if your device is already there, delete it. not totally necessary, but cleaner)
select your device and tap next
enter passkey
tap next
once it scans for services on the computer, it should find activesync.
tick it and tap finish
in activesync, tap menu
tap connect via bluetooth
should be gravy!
Maybe I am missing something here. I used to use the DUN with my 8525 and never had a problem with my laptop. I flashed today with XDA .20 and can not figure out how to work the new PAN. I tried everything and just can not get it to work. Am I missing something?
Use the internet sharing app. If you are tethering via USB make sure to disable bluetooth or your device won't get a DHCP lease from the PAN driver.
I have a problem connect Via bluetooth using Internet Sharing with all version of WM6. When pair with the PC, the PC can only transfer file with my 8525 only. But when using Cingular 3.3 aku my PC can find Serial port profile and connect to Internet Sharing.
Does anyone know a registry fix for this?, I am using a Sony laptop with build in toshiba bluetooth stack. When went back to 3.3 aku internet sharing Via bluetooth work again.
Thanks
tandao said:
I have a problem connect Via bluetooth using Internet Sharing with all version of WM6. When pair with the PC, the PC can only transfer file with my 8525 only. But when using Cingular 3.3 aku my PC can find Serial port profile and connect to Internet Sharing.
Does anyone know a registry fix for this?, I am using a Sony laptop with build in toshiba bluetooth stack. When went back to 3.3 aku internet sharing Via bluetooth work again.
Thanks
Click to expand...
Click to collapse
Now I dont feel so bad - this is exactly what is happening to me.
bluetooth PAN does NOT works with toshiba stack! upgrade your laptop to Vista and don't install toshiba stack! Vista (microsoft) stack works!
netnerd said:
bluetooth PAN does NOT works with toshiba stack! upgrade your laptop to Vista and don't install toshiba stack! Vista (microsoft) stack works!
Click to expand...
Click to collapse
I have vista and winxp with toshiba stack on the same laptop (dual boot), both doesn't work with all version of WM6 available here, but it work with 3.3 aku cingular rom.
Where can I find MS stack? when I unintalled toshiba stack, all the driver for the bluetooth is gone.
Edit: Thanks for the tips, I finally get it to work VIA bluetooth, the problem is the toshiba bluetooth stack. I uninstalled the toshiba stack, and do and manually driver installed and choose Toshiba as the manufacture, and intergrate bluetooth, Vista find a driver for it and activate the MS stack.
The issue with the Toshiba stack is this:
The auto discovery is the only way to set up services. However, the PAN service doesn't display unless the devices are paired. Toshiba can only Pair with devices seen during discovery....
Its a damn catch-22....
Sleuth255 said:
The issue with the Toshiba stack is this:
The auto discovery is the only way to set up services. However, the PAN service doesn't display unless the devices are paired. Toshiba can only Pair with devices seen during discovery....
Its a damn catch-22....
Click to expand...
Click to collapse
screw the toshiba stack! just dont install that junk, Vista will automally install Microsoft bluetooth stack!
Can someone please detail the steps on how to get Internet Sharing via bluetooth for either XP or vista?
TIA!
Interestingly, there's a help topic in WM6 that explains this! Tap Start->help and then choose "search"
Now search for "Internet sharing". How to set up the m$ bt stack on your desktop is explained there.
M$ stack
I just have the same prob. on my laptop with XP SP2 and toshiba BT stack...
how can i fix the drivers for M$ BT stack without install VISTA ???
THX in advance
vdavide
Since upgrading to WM6 Black, I can't seem to get the Wireless Modem (internet sharing) to work. I am using a USB cable but when I start the DUN on the PC, it says there is no modem installed.
found the answer elsewhere - if you are using USB turn off BT on the device!
obvious really (?)
replacing Toshiba BT stack with Microsoft
Hey, I cant vouch for this since i dont have a toshiba but thought i might pass this on. hope it helps.
http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_dtlViewDL.jsp?soid=841048
Is there any way to use old wmodem from WM5 on WM6. I have public ip and im afraid that using Internet Sharing make that i will be behind nat? If i think correctly? /dont have wm6 on hermes/
warmkiwi99 said:
Since upgrading to WM6 Black, I can't seem to get the Wireless Modem (internet sharing) to work. I am using a USB cable but when I start the DUN on the PC, it says there is no modem installed.
Click to expand...
Click to collapse
Hey bud, Microsoft ditched DUN in WM6. If you have the drivers installed properly (included with Activesync 4.5) you should see a new LAN connection in your Network Connections. In Windows XP it should be described as "Windows Mobile-based Internet Sharing Device" If you don't have the driver installed you will see Generic RNDIS in your Device Manager. From what i understand if you have Vista installed on your computer these drivers come stock (on the Final full version of Vista, not included by default on RC1, not sure about RC2)
hope this helps...
PAN with toshiba stack
I downloaded an updated bluetooth stack from
http://aps.toshiba-tro.de/bluetooth/pages/download.php
and it worked fine.
Pair hermes with computer. First turn on internetsharing then connect using pan profile.
TheLuggs said:
I downloaded an updated bluetooth stack from
http://aps.toshiba-tro.de/bluetooth/pages/download.php
and it worked fine.
Pair hermes with computer. First turn on internetsharing then connect using pan profile.
Click to expand...
Click to collapse
... mmm interesting ... wich version of toshiba stack you used ? and wich version of WM6 on your device ?
I tried the very latest version of toshiba stack with LVSW first WM6 version but doesn't work .... only the M$ stack work ( fine too ).
Bye
vdavide
vdavide said:
... mmm interesting ... wich version of toshiba stack you used ? and wich version of WM6 on your device ?
I tried the very latest version of toshiba stack with LVSW first WM6 version but doesn't work .... only the M$ stack work ( fine too ).
Bye
vdavide
Click to expand...
Click to collapse
Bluetooth stack:
v5.10.06
bluetooth spec:
2.0,1.2,1.1
with jasjamming's WM6 Black 2.0
works like a charm, couldn't get it to work wit the older toshiba stack supplied by asus (3.03.04)
TheLuggs said:
Bluetooth stack:
v5.10.06
bluetooth spec:
2.0,1.2,1.1
with jasjamming's WM6 Black 2.0
works like a charm, couldn't get it to work wit the older toshiba stack supplied by asus (3.03.04)
Click to expand...
Click to collapse
i tried the v 5.10.06 too on my asus but still can't connect to my tytn WM6 LVSW first release .... maybe the different WM6 is the key of this problem...
wich options u use in the toshiba stack ( security level and so on ) ?
i tried high security level that force pairing with device ( and obviously pan enabled) but still get the message " only file tranfer service on the device ..."
i'm interested to get it to work too also if it's working now with m$ stack .
There may be some other users interested too...
THX
vdavide
Hi, i've upgraded my Tytn succesfully to WM6 Black Edition, works like a charm, great performance (better then WM5) only one major problem is that i cannot activate Rsap with "sapsettings" that doesn't seem available. I've downloaded the "ActivateMSBluetoothSAPProfile.cab" from another ROM but that gives an error.
Is there a ROM that has "Sapsettings" in the programs? I'd install that one then.
Any help is appreciated. Thnx.
Hi, I've had the same problem after upgrading my Hermes 300 to 3DES.3
I was missing the SAP or rSAP, which I needed for my Passat.
I found an OEM package here: http://wiki.xda-developers.com/index.php?pagename=HTC_Universal_WM6_Kitchen_Helmi
and downloaded the btsapprofile (direct link: ftp://xda:[email protected]/Uploads/Universal/helmi_c/Kitchen_OEM/btsapprofile.v1.45.rar)
Extract the content of this file to your PC. Copy SAPSettings.lnk to \Windows\Start Menu\Programs on your phone.
Copy SAPSettings.exe.0409.mui, sapsettings.htm, SAPSettings.exe, SALib.dll, BtSim.exe to \Windows on your phone.
Go to Programs on your phone - you should find a working link to SAP settings.
This did the trick for me.
Cheers - mgruett
You are my hero! Works 100%. Thank you!
While looking into this issue i found anothern, maybe easier solution together with my collegues (same problem here, for the VW Passat fleet)
Just open this file, unrar, copy .cab file on your Hermes, execute, softreset and off you go.
http://forum.xda-developers.com/attachment.php?attachmentid=29801&d=1155792304
tested it on 2 Hermes with WM6 and it works flawlessly.
rSAP with TyTN, s620 and Wizard
Hi,
when you're saying "100% working" and "works flawlessly" do you mean you have the Icon in your program folder or is it really working well with your car-kit ? Make phonecalls, Syncs phonebook etc. ???
I've a carkit from THB (bury) since ages in my car and upgraded the phone holders from old nokias up to the LT9100 with rSAP. As rSap pops up, I was 100% sure that this is the solution I'm looking for.
Since 6 months now, I try to get that damn thing working. It always fails with "Sim Card missing / not found". I could pair, it connects to the phone, disables the phone-module, but I couldn't dial a number, nor could I sync the phone book.
I tried it with Blueangel, Wizard, TyTN and my brandnew S620 without succes. I tried it with PPC 2003, WM5 and WM6 Roms, no chance. Of course, I followed the hints in the forum.
I sent the carkit to Bury to upgrade to the latest firmware and guess what ... nothing, always the same problem with Windows Devices, but my Nokia 9300 connects well in a second.
So, bottom line, I'm not sure if it is a Bury Problem with a bad rSAP support for WM or a WM Problem as my Nokia connects well.
Any thought or tipp is highly appreciated
Thanks
Chris
I just tried the download from WDawn (thanks incidentally) and aside from it resetting my background to the windows default, worked just fine. Enabled SAP, gave the phone a poke up the rear and tried it on a Nokia 616 car kit. This car kit uses SAP if available, otherwise falls back to HFP. It quite happily connected via SAP. Next text with be the Mercedes Bluetooth module, which would have to be the fussiest car unit I've ever come across and it only supports SAP (no HFP, HSP.. or other fall back).
The phone used is a DoPod 838 Pro running the newly released official WM6 ROM. I never had this success with the cooked LVSW ROMs that I used in the past.
Alex.
Progress but still troubled
WDawn said:
While looking into this issue i found anothern, maybe easier solution together with my collegues (same problem here, for the VW Passat fleet)
Just open this file, unrar, copy .cab file on your Hermes, execute, softreset and off you go.
forum.xda-developers.com/attachment.php?attachmentid=29801&d=155792304
tested it on 2 Hermes with WM6 and it works flawlessly.
Click to expand...
Click to collapse
Hello!
I have a HP Ipaq 914c and having troubles connecting with the VW Passat.
Here are the steps that I have made so far. Any help will be much appreciated.
1) Initialy on the VW menu searched for BT phones. Detected mine but whenever I selected it, returned back with the message: "Phone not compatible"
2) Dicovered here this tool BTSAP_Test, installed on the Ipaq and activated the "Remote SIM Access" checkbox button
3) VW now is able to pair with the phone (after inputing the 16 code number) but immediatly after pairing says that "Bluetooth is not activated on phone" ...
4) Looking on BT devices in IPAQ I can now see a device named "VW UHV PREM", but the only available service to use for this device is "Dialup Networking".
Am I missing something ? Thanks.