i am trying to connect via usb modem but when i press start button my network connection show disable.after press stop its back again.i already hard reset once but result same.
is this a hardware problem or anything else/
pls help someone.
Why you don't want to use Bluetooth Dial-Up netoworking? Or maybe Internet Sharing (works also on USB)?
Related
While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy
Hello,
After I upgraded my ROM. I am having problems using Active Sync. It won't detect the device when I connected the USB cable. I tried soft reset, hard reset, remove, reinstall active sync and reboot the PC, also used two different computers and it still doesn't work.
I also notice that my dialing keypad won't show up when i press the "call button". Comm Manager shows that my phone is off. Tried turning it on by tapping as well as holding the Comm button then tap..doesn't work either..
Please help! I am thinking of downgrading the ROM to 1.8 to see if the phone will work but i cannot get the Active Sync to work..
Here is what I am seeing:
IPL 1.08
SPL 1.08
(am I missing something here?)
OS 2.26.10.2
Need help from anyone. Thanks.
I want to upgrade rom on may diamond but when conect the phone to my conputer the phone it just starts to charge. The computer does not detect him and I have activated usb conection on the phone.
I am using a standard miniusb cable used also for canon fotcamera, Nokia N95, motorola V3 (v360 L6, L7 etc.)
I did instaled Activesync on my computer but still no result.
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
R3PUBL1K said:
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Click to expand...
Click to collapse
I am using Win XP SP2 and I have tried every thing that you said but nothing.
band27 said:
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
I did uncheck that box but without any results so now I will try internal method. But I'll have to send the file to the phone via bluetooth and see if it works.
band27 said:
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
How much is it supose to take "Internal method"?
After pressing Vol_Down + Back button it showed the three color screen then it changed to a white screen with loading on it and it stays like that (after pressing Vol_Down + Back button I didn't press nothing else).
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
band27 said:
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
Click to expand...
Click to collapse
I have tried everything that you said and nothing.
The only diference is that now when I conect the cable to the phone it asks me witch mode to conect it (Activesync or storage), but the computer still doesn't see's it.
Tried another USB-cable?
chribruu said:
Tried another USB-cable?
Click to expand...
Click to collapse
I tried with 3 diferent cables.
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
band27 said:
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
Click to expand...
Click to collapse
It doesn't switch's to usb it only shows "serial". If I put it into bootmode while it is conected to USB it shows nothing, not "USB" or "Serial" it's blank.
I am begining to belive that there is a hardware problem in my phone.
Do you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
Hello guys,
I do have this strange problem on this T3,
I am familiar with Android devices, but this problem is very strange !
1 - the phone won't connect to the PC (so it doesn't connect to Pc companion)
2 - can't install anything (google play not working)
3 - sometimes it connects to Pc (as usb storage)
4 - I can't make it to do a factory Reset !! pressing the button doesn't do anything at all
5 - Bluetooth isn't connecting to any device
Thanks in advance for any help
Problem fixed !!
Basically what I did is a fresh reboot with volume up and power pressed, it vibrated three times then I started the phone with USB cable plugged to the computer, this time the phone was detected so backedup some files and then I performed a factory reset from Settings, and it worked after a while.
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Verity. said:
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Click to expand...
Click to collapse
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
yawarniazi said:
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
Click to expand...
Click to collapse
Yeah, but the point is, you can connect to pc and flash things and I can't do anything, I suspect my computer fried usb board or something on the motherboard bc it's impossible I can't get qualcomm hs-usb loader 9008.
As it turns out, after rebooting the pc, it doesn't boot anymore. Phone doesn't work and pc. Coincidence? formatting pc was needed (pc works now), could it be a virus or my power supply simply gave too much voltage to the usb? I was doing everything during the storm, y'know, thunders.. I don't know anymore, I tried even connecting to a different pc and the result is the same. I can't do anything on my phone, could it be broken usb board?
EDIT: It connects now in edl, I was shorting the pins incorrectly (can't touch the ground [shielding] while shorting the pins). Pls close this thread.