Hi ppl!
I'm newbie on this, but, i'm having a problem with this because i really need the phone and now i can't install any rom...
i have the artemis touch 3.01 rom, and i tried lots of stuff, like, uspl... downgrade to factory..etc and everytime that the device reboot, to bootloader, the screen stays white for a while.. and the rom installer gives me an error...
i disconnected the firewall and everything...
Anyone knows what to do? please?
This rom is pretty and everything, but it is SO slow... :S
Thanx for your time..
Regards
Remove you microsd, maybe it's the cause.
...
No...it's not that... i tried it already...:S
Thanks anyway! I really apreciated!
try 1-3 below
1- which active sync you are using?
try uninstall then re install active sync 4.5
2- try different pc (laptop) better in case of power issues
3- soft-rest your phone b4 flashing some applications like battery status does not allow proper procedure running
4- good luck
Related
Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!
I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.
try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.
I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.
What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.
Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.
Hi guys, I've read and used the forum for years and upgraded my Cingular 8525 a ton without troubles (followed Vanx's method for vista and for upgrading), but this is the first time I'm really stuck without a clue.
I had Schaps latest OS on my phone working fine for about three days. It was charging with the USB hook up to my Computer. I pulled the USB out and the phone entered bootloader. I couldn't get it out. I tried using mtty to no avail, hard reset ect., but finally used the SD loading method to put TNT's latest on it (don't know why this worked). Here's the thing though, the phone will load fine on first load after I flash, but if I soft reset or turn the phone off and on it goes right into bootloader mode. The only way I can get it to load up again is to connect it to the computer's USB, take out the battery and then put it back in. the OS then boots up without fail.
I have read a ton and searched on the forum, and if any of you can help me understand what the hell I can do to fix my phone I would really appreciate it. I will post anymore info you guys would like, I really need your help on this one.
Thank you so much!
Hi,
I posted exactly the same problem today ! here:
http://forum.xda-developers.com/showthread.php?t=381284
It's really strange !
Dave
I've been reading everything and it appears that Schaps's new version seems to have this problem sometimes....I have the exact same problem as everyone else (mtty gives me the same results), and flashing a new rom doesn't get rid of it....I hope there is some way to fix this!
maybe I'll try flashing a new radio and see if that helps things....
I did notice that flashing Schaps 4.31 seems to include radio 1.50 and I had changed my anyway to 1.43 as I thought that was better for my area.
Not sure a radio will help. Maybe a different ROM version will ? Maybe 3.54 ?
I have flashed TNT's rom as well and it still has the problem now....I'm flashing a new radio as I type, I'm going to have to reflash the OS too, it just got stuck again as it was restarting.
Just a quick thing, I think I have solved my problem (not sure if it is permanent) by powering the phone off and on. Not resetting, just a simple power off. I spoke to a colleague who said the way it shuts down is different to soft reset (makes sense) and I haven't powered my phone off properly for a long time.
I have tried soft reset a couple of times since doing this and it hasn't gone to the bootloader screen once.
Maybe this is the simple fix.
I will keep you posted.
try to flash OFFICIAL ROM first , maybe there are few bug / missing file when error appear while flashing other ROM.
I hope it will help you both.
rgds,
ermen
Use mtty to see if yo have any bad blocks... I've had a few problems the same as yours and found I had 1 or 2 extra bad blocks, after the 2 "factory standard" bad blocks I got on my jasjam of course. hope this helps...
My fix didn't work.
Not sure what I am suppossed to see when I run "task 2a".
Has anyone had any luck fixing this ?
Hi, i have been trying for the last month and a half to try another rom on my hermes,but it seems i can't.
i have flashed many Roms and i never had a problem in doing that till the las time when i tried to flash into the new S64.
every time i try flashing into any new rom it rejects me by giving me the (ERROR 260) telling me i'm not connected and the USB cardle thing, but all of my connections are correct and my ActiveShyn is up to date and i was always flashing roms in the same way.
Some seniors here when i have mentioned that told me that it seems i have flashed or reflashed the Hardspl, so i'm trying to reflash the Hardspl, i have tried endless times but it keeps telling me the same althought i have downloaded almost every hardspl that is available in the xda site lol.
what i'm requesting please if possible to direct me in the steps that i need to make my hermes functional again please i'm sure u understand what i'm saying.
some have mentioned that cause i still have the
herm100 i can't flash it into another roms but that sounds a bit strange lol.
I know that i have still herm100 (old) and my ipl-1.01
and spl-1.06 but i think that dosn't matter in my opinion.
Please i request if u can help me in fixing my problem by providing me the steps by simple words and if you have a fresh zips of hardspl coz i'm so confused which one to use, it would be nice to hear how to do it step by step.
i really need your support and excuse me if i'm bothering u with this kind of request but i didn't know where else to go and ask.
My Current rom is the HTC_Hermes_S64_WM_6[1].1_HTC_WWE_v2_30.03.2008 which is old and i would like to refresh my phone by a new version.
i was thinking of the new HTC_HERMES_S64_WM_6.1_TouchFlo2D_UC_ WWE v3 / GER v1 but i don't know if it would work on my herm100 cause i was told it was designed for herm200 and abouve is that true?
If not well there are so many more roms out there i would like to try but i'm stuck for the moment.
please again i wouldn't have bothered u with my request if i wasn't facing this problem.
thank u a lot and i hope to hear soon from u commrade.
Dayhauck.
have you tried to manually go into the bootloader and flash? You don't need activesync to flash like that if you're connected with USB. Also, from your SD card. Both have worked for me in the past.
Though you should have Hard SPL installed if you want to use the sd card method.
i have tried to do it manualy but i not much of a luck in loading the Hard SPL.
I really don't know what to do. i can't even f;ash to the original htc rom .
what else can i do?
1. Check your usb cable.
2. Try different USB ports in ur PC,
3. Check if the mini USB in Hermes is not damaged.
4. Check the bootloader if you have HardSPL installed.
5. Try SD method,
6. Read the wiki.
check out post 1160 on page 116 of this thread for sd card method for Hard SPL V7 - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...
I had the same problem. If you can activesync with the cable then all you need to do as already mentioned above.
With the phone attached manually go into bootloader (hold on/off on right of phone and 'ok' on the left of phone both in while you prod the phone reset at the bottom of the device).
When you have the multicoloured boot loader run the update and it should work fine.
Hope this is some hepl
hi all
after phone couldnt powered on, been doing the tri color thing and tryed to upgrade to nrg's rom. while running the uspl it says phone not connected, but when i running the update it does recognize the phone till it gives the error 270
any suggestions why phone seem to b unconnected while trying runing uspl? thx
btw diabled firewall and antivirus
many thx.
Try using your stock ROM from bootloader....
thx for ur reply
ive flashed the original rom, and it worked, after been trying to update but still at uspl stage it says device not connected
such a shame, hoping threes a solution for this
the-light said:
thx for ur reply
ive flashed the original rom, and it worked, after been trying to update but still at uspl stage it says device not connected
such a shame, hoping threes a solution for this
Click to expand...
Click to collapse
Flash via SD Info of name for file can be found via search or in NRG thread know it was stated... "would find it but very limited data and pap speed"
managed to flash the beautiful rom of nrg-thanks a lot for this rom..
i cant seem to b able to c the windows folder though....
any suggestions?
thx
Hi guys,
i flashed my i780 with the heroes 6.1 rom. after 1 day of perfect functionality i couldnt unlock it because the touch screen didn`t respond anymore. then after some time i managed to unlock it, but it seemed the ui crashed, so i had to reboot. after boot all data were gone like just after a hard reset. i tried plenty other roms but it`s everytime the same. after some time the phone crash and i need to reflash it. so i think that my phone is damaged someway. i still got warrenty, but i don`t have the original roms anymore. do anyone know, where i can download the original samsung wm 6.0 roms (german)? i also need the original phone rom so i can send the phone to samsung. thanks in advance
ouch! That'll be hard to find!
What you could do is order a new i780....and anyway you have a 7 day return and money back option....do a rom dump and send it back
shockabuku said:
Hi guys,
i flashed my i780 with the heroes 6.1 rom. after 1 day of perfect functionality i couldnt unlock it because the touch screen dind`t respond anymore. then after some time i managed to unlock it, but it seemed the ui crashed, so i had to reboot. after boot all data were gone like just after a hard reset. i tried plenty other roms but it`s everytime the same. after some time the phone crash and i need to reflash it. so i think that my phone is damaged someway. i still got warrenty, but i don`t have the original roms anymore. do anyone know, where i can download the original samsung wm 6.0 roms (german)? i also need the original phone rom so i can send the phone to samsung. thanks in advance
Click to expand...
Click to collapse
take a look here --> http://forum.xda-developers.com/showthread.php?t=398874
thx a lot,
once again i tried the heroes 6.1 rom but this time without syncing my phone to my pc. `til know everything works. maybe my activesync is the problem. i try the latest usb driver from samsung. i hope it work
shockabuku said:
thx a lot,
once again i tried the heroes 6.1 rom but this time without syncing my phone to my pc. `til know everything works. maybe my activesync is the problem. i try the latest usb driver from samsung. i hope it work
Click to expand...
Click to collapse
delete the actual activesync and reboot your pc, download the latest version of activesync (4.5) from samsung official site and delete the old connection. reinstall the sw and try again.
Bye
gianvi60 said:
delete the actual activesync and reboot your pc, download the latest version of activesync (4.5) from samsung official site and delete the old connection. reinstall the sw and try again.
Bye
Click to expand...
Click to collapse
hello ... i flash my phone, he got stuck at 13% , after that the phone is stuck at loading windows page, i tried anothers roms but nothing, pls can u help me ? i think i need a official rom or something like that... pls help me, pls teach me
Samsung Office WM 6.1
This is office Samsung I780 Windows Mobile 6.1 upgrade.
http://www.samsungmobile.com/support/i780/index.jsp
you can has a try.
towseng said:
This is office Samsung I780 Windows Mobile 6.1 upgrade.
http://www.samsungmobile.com/support/i780/index.jsp
you can has a try.
Click to expand...
Click to collapse
1. i can`t find the SGH-i780 Updater, when i press the "firmware download" button i go to webside and there is nothing, i can`t find updates.
2. my activesync cannot see the phone so i can`t use a .exe update... just mirage see the phone when is in emergency mode...