Radio flashing problems SX66 - MDA III, XDA III, PDA2k, 9090 General

Who can give me a hand here? I've only had the BA for a couple of days now, have flashed it to WM6 twice, no problems. The radio version is 1.02 and the signal is weak, the sound volume low. I've read the wiki, tried to flash radio 1.15 at least a dozen times, using both of the methods described, but no joy. All I get are country ID errors or device not compatible errors. I followed the instructions step by step and still no luck. Maybe somebody in this community has had the same experience and can steer me to the answer.
GETDEVICEINFO= PH20B1,WWE,AT%CID?,5.70.11,Minhanhtran.pv,1.02.10,%4, obviously, minus the blank spaces and little symbols.
Thanks in advance!

kcguy said:
I've read the wiki, tried to flash radio 1.15 at least a dozen times, using both of the methods described, but no joy. All I get are country ID errors or device not compatible errors. I followed the instructions step by step and still no luck. Maybe somebody in this community has had the same experience and can steer me to the answer.
GETDEVICEINFO= PH20B1,WWE,AT%CID?,5.70.11,Minhanhtran.pv,1.02.10,%4, obviously, minus the blank spaces and little symbols.
Click to expand...
Click to collapse
What 'methods described'?
As far as I can tell, the errors you are describing are covered in the wiki at:
http://wiki.xda-developers.com/inde...rmx20.ax20.Radiox20.ROMx20.upgradex20.onlyx3f.
Can you be a bit more descriptive on what you downloaded, what you tried and where it failed?

Read the wiki first......
Thanks for your reply jdc. I don't know how to be more specific about the errors. In the wiki, there are several methods of flashing the radio rom, but none of them work on this siemens, Cingular phone. I have unlocked the phone and as I stated, no problems upgrading the rom. I've read all the trouble shooting guides about the various error messages, tried all the solutions, but still no luck. I read last night that if you can get the original ship rom for your device you can delete the nbfs you don't want to flash and merely replace the radio nbf in the ship rom folder and flash it. There are links to the ship roms in the wiki, but unfortunately, they are dead links. Maybe somewhere on this site, the rom I need is posted, but I haven't been able to find it. Any help would be appreciated.

kcguy said:
Thanks for your reply jdc. I don't know how to be more specific about the errors. In the wiki, there are several methods of flashing the radio rom, but none of them work on this siemens, Cingular phone. I have unlocked the phone and as I stated, no problems upgrading the rom. I've read all the trouble shooting guides about the various error messages, tried all the solutions, but still no luck. I read last night that if you can get the original ship rom for your device you can delete the nbfs you don't want to flash and merely replace the radio nbf in the ship rom folder and flash it. There are links to the ship roms in the wiki, but unfortunately, they are dead links. Maybe somewhere on this site, the rom I need is posted, but I haven't been able to find it. Any help would be appreciated.
Click to expand...
Click to collapse
OK, let's see if we can step this through. Please forgive if old ground is covered.
Starting with How to upgrade to the latest Radio ROM version:
http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.15_Upgrade
Using the "First Method (Quick/Easy) (TYPE II)", you were able to download BA_RRPT_Radio_11500.exe and MaUpgradeUt_noID.ZIP?
Running MaUpgradeUt_noID.exe, you get an error. What is the exact text of the error?
And when you rerun the program after the error, it errors again. Different error or same error?
Also, what enviroment are you running? XP, Vista, Windows for Workgroups 3.11?

Tried again
jdc,
Reread your post, reread the wiki, downloaded fresh copies of the files ad tried flashing again. Here's what I understand and what I'm doing.
1. Placed BA_RRPT_Radio_11500.exe and MaUpgradeUT_noID.exe in the folder with my rom upgade files, replaced the rom nbf with the radio nbf, and ran MA----.exe.
It shows on the screen and on the mobile that the radio rom is being updated, but nothing happens for awhile, then I get an error message\ Radio romupdate error. Per the instructions in the wiki, I didn't touch my phone or remove it from the cradle and ran MA----.exe again, same error. I then tried running BA_RRPT........exe and got this error\ error:120 Country ID error. I really have no idea what this executable BA_RRPT---- is for.
What step am I missing? Maybe I am misunderstanding the instructions?
Also, I am flashing from WindowsXP.

kcguy said:
1. Placed BA_RRPT_Radio_11500.exe and MaUpgradeUT_noID.exe in the folder with my rom upgade files, replaced the rom nbf with the radio nbf, and ran MA----.exe.
Click to expand...
Click to collapse
Why do it that way? If your OS is fine, why try to reflash the OS as well?
When I did mine, the radio stack was flashed separately from the OS.
Download BA_RRPT_Radio_11500.exe and MaUpgradeUt_noID.zip, extract the radio, extract MaUpgradeUt_noID into the radio directory, and run MaUpgradeUt_noID on it's own.
Does that throw an error?
kcguy said:
Also, I am flashing from WindowsXP.
Click to expand...
Click to collapse
Good. Vista is know to interfere and be a general pain in the arse all the way around when it comes to flashing the phones.

Success, finally!
jdc,
Thanks for trying to help, but this seems to be a problem with the SX66 in particular. After reading many old upgrade posts, I found a user who had uploaded a radio utility specifically for the SX66. Tried it, first time, no luck, second time went through like a charm. I don't know why the siemens is any different from the rest of the BA models, but evidently it has some specific issues. Haven't had time yet to see if the signal strength and sound vol are any better, but here's hoping.
Thanks again
Steve

kcguy said:
jdc,
Thanks for trying to help, but this seems to be a problem with the SX66 in particular. After reading many old upgrade posts, I found a user who had uploaded a radio utility specifically for the SX66. Tried it, first time, no luck, second time went through like a charm. I don't know why the siemens is any different from the rest of the BA models, but evidently it has some specific issues. Haven't had time yet to see if the signal strength and sound vol are any better, but here's hoping.
Click to expand...
Click to collapse
Well, you got it, that's what counts. Glad to hear it!
I have heard of some phones not accepting the flash the first time, but will if done a second (or more!) time. Totally bizzare.
The post you are referring to, can you link it here? I'd like to see it myself.

Post requested
Hi jdc,
The post you asked about can be found here: xda-developers > Blue Angel > Blue Angel upgrading etc.
New Radio 1.15.00
It is post #57.
Thanks for your help!

In case anyone has this problem like I am, and don't want to search through many threads to find the link, here is the utility kcguy is referring to. And here is the thread he found it on.

Related

Quick question regarding ROM upgrade please..

I'm trying to upgrade my IIs from 1.12.62 to iMate's 1.22 ROM, I read carefully thru all the posts here and I *think* I have everything set...
1) Got the xda3nbftool file and written the bat file to modify the ROM...
2) Got the Device Date file from my IIs etc
Am I correct that after the upgrade, I'll loose all original O2 or my carrier's setup from the extended ROM they provided? And bascially, my unit will be turned into a PDA2K right? Is it possible to retain all the O2 files etc while only upgrade the MS and Radio files?
Hey there CL55,
There is much discussion on this forum regarding this issue. I have done this upgrade myself and know it very well.
I used this particular post - http://forum.xda-developers.com/viewtopic.php?t=14912 and followed the instructions by ohmlogic to complete the upgrade.
If you need any help or get stuck, Private Message me and I'll see what I can do.
PS: BEFORE you run the upgrade install make sure you have run the GetDeviceData.exe on your phone and retreived the file \windows\devicedata.txt (also from your phone)!!! This is very important and contains the data you'll need to import into your setup files in order to get it to work. If you get this wrong you will lock your device and wont be able to use it!!!
Hope this helps - good luck!
Dom
CL55
Yup, you did your homework
Your Phone will look and feel like an I-mate.
Is this a problem, well not realy.
Was not for me and I went form T-mobile in German to I-mate in WWE.
Now there is a whole section on Extened rom, the short is that your provider has added files that they thought were cool. They have put them in a place were you are not meant to see them. However this forum gives your tools that will "unlock" and Unhide" this folder.
If you need this option is up to you and your own understanding.
The fact remains that most of them are unremovebale thus you cant just go over the "remove progams" to get rid of them. So you might end up with software that you can't use or im my case I lost the PDF viewer and zip.
Givem that you have a FTP tool you could have a look at the exteneded roms that are on this server. Internet explore will error on you.
ftp://xda:[email protected]/BlueAngel
Here you can download the ones that look intresting to you and extract the *.Cab files that you like (Like the zip). Copy them over to your device and with explorer click on them to install.
Also you might have had seetings for your Voicemailbox number and your SMS sending number. These are also gone and need to be added again.
There is also a thread about the Splash Screens (what you see when you boot) Here to you can change them if you have the original ones. (I asked were they were hided in that thread but never got an answer.
So for me, I am fine with the I-mate release and the added *cab files that i got out of the other extened roms. All of which can be done without any further tools than what you have mentioned.
Please be aware that for version 1.22 and above the format has changed and that the xda3nbftool.exe may error out on you.
I have tried to start a thread on what has worked for which operator to help people out on this subject.
http://forum.xda-developers.com/viewtopic.php?t=15510
Have fun
Thanks for the reply guys Like I mentioned in another topic, I just found out O2 has 1.31 ROM avilable thru their repair center! Will give that a shot first Thanks again!
CL55,
Excellent! Well, let us know how you get on and also it would be cool if you can upload it to the ftp here - ftp://xda:[email protected]/BlueAngel/ - so others can try it out!
Regards,
Dom

Unlocking Cingular 8525

I spent a whole day yesterday learning to unlock my new Cingular 8525. Then I tried it using HTC Hermes SIM Unlock v2a, and I followed closely discussion threat between crazyut and pof (http://forum.xda-developers.com/archive/index.php/t-286248.html), but I failed!
Steps as follows: I directly run RUU until ERROR 114 appeared. Then tried to copy HERM_Unlock_v2.exe to the phone, but found that I need to install the software to enable transfer of file from computer to the phone, so I install it. Unfortunately, the installation failed. In Device Manager there is item Windows CE USB Devices, with sub-item: HTC USB Sync(!). There is message: This device cannot start (Code 10). Then I tried uninstall and reinstall, but did not work.
So I use another computer. It can be installed, and connect the phone to this computer, and transfer the file. But I could not run it (I double click it; and also tried to run from: Start, Run, but no response).
Question: (i) Can the phone still be unlock (since the process was interrupted), (ii) Can I continue the process using another computer?, (ii) how can I transfer the file to the phone that can be executed, so I can complete the process.
Appreciate your help.
what bootloader do you have??? one of the first lines in the hermes unlocking thread is this:
It can be used in all HTC Hermes devices, the only restriction is that the device must have bootloader version 1.04
How to enter bootloader can be found here: http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
there is no need to post the same question in different threads. I have deleted your other post in regards to this matter. Next time make a post in the device specific thread
Many thanks finally a response to my posting (noted also your note regarding second posting - thanks). My bootloader is 1.06.
My understanding is that I can downgrade the bootloader from 1.06 to 1.04 using MaUpgradeUt_noID.exe program, is this correct?
During the process, there is already a message "ERROR 114" as mentioned in Install instruction.
as an FYI you would have gotten a faster response in the hermes upgrading board.. but here is a post you need to read about downgrading your bootloader.
http://forum.xda-developers.com/showthread.php?t=284401
when you follow those instructions make sure you follow #3 as stated.. if its not done as stated you will not accomplish this correctly...
Thank you, I will check and read the info from the link you mention. I.ll get back to you later. Thanks
I have googled the DownGrade_SPL.rar for more than a couple of hours, but could not get free file. All website that I found, we should pay, and some of them $35 - is this really the case? Is there website that can provide free file? Thanks
you dont need the downgrade....
first flash your phone cingular 1.6 bootloader phone with this..it will change your cingular phone to bootloader 1.4..both files are from cingular roms which makes you abe to downgrade your phone from cingular 1.6 to the 1.4 bootloader..understand??
http://forum.xda-developers.com/showthread.php?t=277664
Then follow instructions from here http://forum.xda-developers.com/showthread.php?t=282073
after that you're phone should be unlocked and supercid...
it works.. i have done it to my cingular phone.. just read read and read some more.. everything you need to know is adressed on this website....
Enjoy
honestabe said:
you dont need the downgrade....
first flash your phone cingular 1.6 bootloader phone with this..it will change your cingular phone to bootloader 1.4..both files are from cingular roms which makes you abe to downgrade your phone from cingular 1.6 to the 1.4 bootloader..understand??
http://forum.xda-developers.com/showthread.php?t=277664
Then follow instructions from here http://forum.xda-developers.com/showthread.php?t=282073
after that you're phone should be unlocked and supercid...
it works.. i have done it to my cingular phone.. just read read and read some more.. everything you need to know is adressed on this website....
Enjoy
Click to expand...
Click to collapse
thanks for pointing that out.. i COMPLETELY forgot about that... my head was definitely not in the game last night... Thanks
Many thanks to Shogunmark and Honestable for the advise. I have open the link and it seems that I need to study that first before proceed with thyis great work (e.g. I need to understand how to flash the cingular 1.6 bootloader with ... what file? -apologies for not understand some jargons). Let me also go through the information in the links. And I will get back to you, if I need further clarifications.
Many thanks
Re: Unlocking the 8525
Why not just call Cingu;lar and ask for the unlock code. If your a customer for more than three months, they have to give it to you!
noonrrr said:
Why not just call Cingu;lar and ask for the unlock code. If your a customer for more than three months, they have to give it to you!
Click to expand...
Click to collapse
cause this does more than unlock sim on the phone, this also unlocks the cid on the phone as well...
Hi! I made it!
I learn much from the process. I found the forum has been an exellent site for consultation and discussions. Thanks much to Shogunmark.
All the best for the New Year!
Broto123 said:
Hi! I made it!
I learn much from the process. I found the forum has been an exellent site for consultation and discussions. Thanks much to Shogunmark.
All the best for the New Year!
Click to expand...
Click to collapse
Thats what this whole community is here for! Enjoy your device

upgrading the ROM - a noob guide

Hi all
please dont flame the n00b. I have recently acquired my first smartphone the diamond and am very pleased with it. I have read through the threads and have developed my understanding of the considerations to make in flashing the ROM on my phone
I have an early version of the ROM as I received one of the first stock into the UK, which turned out to be grey imports from hong kong :S . I would like to realise some of the speed / battery / bugfix benefits of the newest ROM
however many of these threads are quite long , so i was wondering if someone could do me a favour by succintcly summarising the steps i would need :
my phone is runnning :
1.34.831.1 WWE - the unit is from hong kong i beleive, i have registered on HTC HK e-club
I would like to upgrage this is the latest signed UK ROM ?
If this is not possible can advice be given on going to the latest HK WWE ?
I understand this will involve changing the HARD SPL ?
Additionally can any method provided be confirmed as a reversible process should i need to invoke the warranty ?
thanks in advance for your help.
please let me know if you need any further information form me in order to help.
thanks
1: install hardspl (unsigned)
2: search the threads for the newer HK stock roms, they've been posted by tudispin I think.
3: flash
4: should need arise, you can revert to stock spl, search the threads for spls by htchackers.
you should be able to flash back for warranty purposes.. safest thing is still to dump your current ROM (search the forums and wiki for how-to), but i think you'll be alright. You can check out my site for step-by-step instructions on how to upgrade your ROM
thanks so far
just for help so far
your guide looks great racerx_
so i should be able to do the following tonight
1: install hardspl (unsigned)
2: search the threads for the newer UK? stock roms,
3: flash
4: and should the need arise, you can revert to stock spl, search the threads for spls by htchackers.
once the hardspl is loaded am i correct in thinking any ROM can be loaded ?
oh but
dump my current ROM before proceeding .. just in case
porkmince said:
just for help so far
your guide looks great racerx_
so i should be able to do the following tonight
1: install hardspl (unsigned)
2: search the threads for the newer UK? stock roms,
3: flash
4: and should the need arise, you can revert to stock spl, search the threads for spls by htchackers.
once the hardspl is loaded am i correct in thinking any ROM can be loaded ?
Click to expand...
Click to collapse
yeah you should technically be able to load any ROM... if signed Hard-SPL, then only any signed ROM of course
hit a slight problem
So i am tryiong to HARD SPL. have gone through all the instructions but :
when installint the HARD SPL . the phone screen switches off the progress bar on PC sits at )% for about 20 sec it then accelerates to 100% very quickly within around 2 mins. It say that is is installed correctly
however the phone restarts and i can still see the d: as 1.34.00.00
so the loinex 1.3 has not installed
the windows is hard reset as i then have to go through the screen calibration
any help appreciated
HardSPL is not the ROM, just software to enable the update
once you installed HardSPL you should now be able to install a ROM
hi
yes sorry for the confusion in my past previous description. It is the HARD SPL software update which says that it is installed but isnt
i have not attempted to load another ROM until this is done first
any further advice ?
in essence when installing the olinex 1.30 i get no errors
bit it doesnt install and all i get is a hard reset ?
If it goes through OK, it has installed You don't see anything different in the splash screen- that just lists the basics
To confirm, go into Bootloader mode by holding down the Volume Down Key and at the same time pressing the red reset button at the mouth of the stylus silo. It can take a few goes, but will show a rainbow screen listing the SPL etc, which ought to say 1.30 Olinex, confirming the correct SPL flash.
Once confirmed press the reset button to restart.
ok thanks for step by step advice there
the HARD SPL is loaded version 1.30 I will try a new ROM now
i am trying the :
RUU_Diamond_hTC_Asia_WWE_1.37.707.1_Radio_Signed_Diamond_52.26a.25.09_1.00.25.03_Ship
which is signed so should work
mmm even though the phone is synced up I get error
"262" when i try to install new ROM
it basically stalls on 0% for about 4 to 5 mins before it aborts with this error message.
i have searched the forums but cannot see a succinct plausible answer
hmm.. i thought that error was usually encountered with unsigned ROMs...
1) are you flashing with xp or vista
2) are you connected through a USB hub?
3) what EXACTLY are your steps for flashing this ROM
hi there
yeas flashing through vista 64 bit
and not using USB hub but direct connection
I downloaded the signed 1.37.401.3 Europe ROM linked from this forum and this installed fine
the improvement over the old ROM is immense. so far i am delighted by the results.
I am still perplexed as to why the asian ROM did not install still :S
only difference so far is that this EUROP ROM does not have the remote desktop app
thanks for all your help. I am going to test this ROM over the coming week, but unless there is a compelling reason to another ROM i will stick with this
Why HARDSPL when flashing HTC rom?
When using the newer 1.37 roms, you download the installer from e-club, make activesync conn en go for it?
A noob's point of view
I got my Diamond about two weeks ago, and since I'm new to PDAs and WM, I've done a lot of reading on the forums, wiki etc. At first things were quite murky for me and I know what my fellow noob here is feeling. So I thought I should share my experience (or lack there of) for the use of other noobs.
What I Know
HardSPL is needed in order to flash a cooked (non original HTC) ROM. As I understand, it is the equivalent of BIOS for PCs, mixed with a bootloader flavor. You need to first change this section of software first in order for the cooked roms to be accepted.
HardSPL comes in two flavours:
- the developer edition with which you can flash any type of roms (signed, unsigned, original) link: HardSPL dev ed
- the signed edition with which you can flash signed roms (original HTC, and cooked signed). The signed ROM versions give an added sense of reliability since they are tested. link: HardSPL signed the topic name was confusing for me at first
A list of signed ROMs: here
There are more than one "cooks" out there working in teams or otherwise. And more than one ROM you can flash. I did a lot of reading before I chose the one to use, I find user feedback the best measuring tool for quality .
Now for the flashing part
After you downloaded the HardSPL and the chosen ROM, you need to install ActiveSync. This is found on the CDs that come with the device, or downloadable fromo the M$ ****e aaaa site ActiveSync is a tool used for transferring contacts, e-mails and other outlook stuff if you use it, files, AND is needed for the flashing process. When installing, if you do not use outlook and do not like "syncronisation folders" on your desktop uncheck every "folder" option, you will be better off.
This site was very useful to me since it gave a detailed description flashing with visual documentation which (a bit uncomfortable to admit) was very helpful for me.
The HardSPL flash takes little time to complete and unless going into bootloader mode (vol down + soft reset) is completely transparent to the user.
The ROM flash takes longer 10 mins - they go by pretty slowly .
For safety reasons, I also downloaded an original HTC ROM just in case.
Because the flashing process once started SHOULD NOT be stopped there are a few things to consider:
- charge the battery
- firmly and directly (no hubs) plug the USB cable into computer and device.
- if you live in an area where power cuts are often consider doing the flashing on an UPS-enabled computer.
When the flashing finishes, the device will reboot and you will have to set-up again. If using TLRs ROM do not panic if you have to align the screen 6 times or so as I did. You will eventually get to the next step
What I don't know or am not sure of:
- when using signed HardSPL can I load an original HTC signed ROM? if so, is this enough in case of RMA issues?
- when reflashing with a newer/different ROM can I restore a back-up made with the previous ROM? I'm using sprite and I backed up everything, including what registry stuff it offered to. In this case, do i need to reapply the registry tweaks? dunno if sprite backs-up all the registry or just some of it.
Im must thank guys for this thread, i am minutes from going to the postal office to get my Diamond and this weekend has been full of information reading and program downloading, but the only thing i was a bit hung up on was this flashig buisness. Of course i know a lot about flashing ( Right about everything there is to flash ) but almost nothing about Phone Flashing
But i think i will try the version i get now first to see if i feel the need to update to anything else...
Hence my question is rather simple... How tha fack do i see what version i already have? >_< is it that (vol down + soft reset) thing? or am i way out of place?
thx.
Reb0rn said:
How tha fack do i see what version i already have? >_< is it that (vol down + soft reset) thing? or am i way out of place?
thx.
Click to expand...
Click to collapse
No, that is for HardSPL info. To see the ROM version, go to settings - device info and you'll see both ROM and radio.

Unable to flash Diamond with new ROM

I cannot flash my Diamond with a new ROM. I have tried using HardSPL versions 1.23, 1.24, and 1.34,and various ROM's but with no joy.
I have done a hard reset on my phone and setup an active sync connection with my PC. I then run HardSPL, which I get the screen with 4 colours on my phone and then get the progress bar displaying 0% on my phone, but doesn't get past that, the program times out with a communication error.
When I take out and replace my battery my phone still works fine.
Please can anyone give me advice.
Thanks
same here.
ROM 1.37.401.3
radio 1.00.25.03
WWE
paul_32 said:
same here.
ROM 1.37.401.3
radio 1.00.25.03
WWE
Click to expand...
Click to collapse
Dito for me!
Saw this coming
Indeed, not a surprise to see another thread opened by newbies.
Partly (small part though) we might point the finger at the HARD SPL creators and the Chefs.
Too many ROMS with sometimes confusing "signed" or "non-signed" versions (and this is for you newbies) WHICH NEED A DIFFERENT HARD SPL.
Unsigned and Signed ROMS can not be flashed with same SPL guys .
So, start readin these threads about the ROM you want to flash profondly and use SEARCH.
In a few weeks, you'll have to write this message to newer Newbies again.
Maybe I better ask a MOD to close this thread though
Look here ! The solution is near
Just an example how you will feel in a few minutes
http://forum.xda-developers.com/showpost.php?p=2420277&postcount=125
ceevee369 said:
Indeed, not a surprise to see another thread opened by newbies.
So, start readin these threads about the ROM you want to flash profondly and use SEARCH.
In a few weeks, you'll have to write this message to newer Newbies again.
:
Click to expand...
Click to collapse
The problem is: We get a connection error a while after the black screen during the hardSPL procedure. And the SPL is not updated...
So if you know what the reason is that the device wouldn't enter SSPL automatically (JumpSPL.exe 0x800000 sspl-1.01-reloc-mod.nb)? Mine didn't respond! I try to used another USB port but …same problem!
I tried to run " JumpSPL.exe " directly from the diamond... then the screen turned black (backlight still working good but the whole screen is black)
Thx for your answer!
Well, I had the same problem, and managed to work around it! First of all, I have NO idea why all of a sudden my Diamond would stop going into bootloader mode by itself - instead, all I get when trying to flash is a screen which fades to black, and then eventually the comm error after 5 minutes, with the option to go into recovery mode.
This is what works for me: first of all, make sure you have the right HardSPL for what yoyu need to do. Either flash the one for the signed roms (and the only try to flash signed roms) or flash the one for unsigned roms (and then only flash unsigned roms). But how to flash if the screen goes black and you do not get a connection?
Well, what works for me (and it may not work for you - try at your own risk!), is to put the phone in bootloader mode by holding the -Volume button and doing a soft reset, and then connecting it to the USB cable of the PC. When the lettering in the white part changes from Serial to USB, you are ready to go, and - at least for me - the flashing works.
Don't ask me why, but this is what I did last night to put the .05 radio on my Diamond.
ceevee369 said:
Indeed, not a surprise to see another thread opened by newbies.
Partly (small part though) we might point the finger at the HARD SPL creators and the Chefs.
Too many ROMS with sometimes confusing "signed" or "non-signed" versions (and this is for you newbies) WHICH NEED A DIFFERENT HARD SPL.
Unsigned and Signed ROMS can not be flashed with same SPL guys .
So, start readin these threads about the ROM you want to flash profondly and use SEARCH.
In a few weeks, you'll have to write this message to newer Newbies again.
Maybe I better ask a MOD to close this thread though
Click to expand...
Click to collapse
Thanks ceevee369 it works fine for me now
I still cannot get a new ROM on my diamond. When I said it worked above that was only getting HARD SPL on my phone.
When I try to update the ROM it gets to 100% and then says the ROM is corrupt. I have tried with different ROM's and I get the same error
creation said:
I still cannot get a new ROM on my diamond. When I said it worked above that was only getting HARD SPL on my phone.
When I try to update the ROM it gets to 100% and then says the ROM is corrupt. I have tried with different ROM's and I get the same error
Click to expand...
Click to collapse
Could you please give the UNSIGNED developers SPL a try?
You only used he Signed version ones as you wrote in 1st thread, and as far as I can feel, you try to flash unsigned ROM's maybe?
Hope you're not bricking your device soon.
Did you posted in the specific ROM thread a specific question on the hard SPL you use vs. The ROM you intend to flash?
Yes, bootlader will always start, but no, it won't go further than giving you an error if no compliant Rom is used.
ceevee369 said:
Indeed, not a surprise to see another thread opened by newbies.
Partly (small part though) we might point the finger at the HARD SPL creators and the Chefs.
Too many ROMS with sometimes confusing "signed" or "non-signed" versions (and this is for you newbies) WHICH NEED A DIFFERENT HARD SPL.
Unsigned and Signed ROMS can not be flashed with same SPL guys.
So, start readin these threads about the ROM you want to flash profondly and use SEARCH.
In a few weeks, you'll have to write this message to newer Newbies again.
Maybe I better ask a MOD to close this thread though
Click to expand...
Click to collapse
The majority of these "help me" posts wouldn't be necessary if the information on this forum was a little more accessible - and seriously, the search engine returns so much dross that it takes an age to gather all the relevant info about roms, spls, flashing, cooking etc, etc. And yes, modmydiamond.info is a cool site but the info there is basic at best.
I'm not knocking the work being done here as it's seriously good - I'm a techie from way, way back, so I can appreciate the amount of effort involved - however, you guys make a rod for your own back by not producing documentation that is more explanatory (or just there) to start with.
And yes, I can also appreciate that you're a bunch of dudes doing this for free and for the love of it and not a bunch of technical writers getting paid for your work but you have to try to understand what a newbie is faced with when they arrive at this site looking to upgrade their pride and joy. Confusing and contradictory are two words I'd use.
Peace.
Ade
PS. ceevee369, the "you"s above weren't necessarily directed at you.
Everytime I'm trying to Hard-SPL my phone disconnects and tryies to install a device called "Qualcomm CDMA Technologies MSM" but doesn't find a driver for that. So there is no connection left between the Phone and the PC and it doesn't work anymore...
Can anyone look if that device is installed on his PC? And if possible upload a driver for that?
Found a way to solve the problem:
Go into bootloader-mode (volume-down + reset) and then connect to the PC. If Win is looking for the drivers you will find them in the folder where ActiveSync was installed. Afterwards you should see "usb" instead of "serial" in the screen on your XDA.
Now soft-reset and proceed as told everywhere...
So my problem was that Win Didn't finde the drivers automatically and i didn't know where to look for them.
ceevee369 said:
Could you please give the UNSIGNED developers SPL a try?
You only used he Signed version ones as you wrote in 1st thread, and as far as I can feel, you try to flash unsigned ROM's maybe?
Hope you're not bricking your device soon.
Did you posted in the specific ROM thread a specific question on the hard SPL you use vs. The ROM you intend to flash?
Yes, bootlader will always start, but no, it won't go further than giving you an error if no compliant Rom is used.
Click to expand...
Click to collapse
Its working now, I used the unsigned SPL. Although when I was using the signed SPL I was trying to Flash ROMs that had been sigened.

Help Me Please

Hey everyone, my phone has a faulty microphone on it and it is less than a year old. Everyone I talk too whenever I'm on the phone say my voice sounds very muffled almost like I am talking though a pillow. I am currently running the NRG rom and no one else has this problem, and I've tried numerous microphone boosters and volume fixes. This phone is less than a year old so i'm going to take it to AT&T and see what they say. How can i flash a stock ROM and make it so they can't tell i ****ed with it
Read this thread, the relocker is towards the bottom of post.
http://forum.xda-developers.com/showthread.php?t=550131
F2504x4 said:
Read this thread, the relocker is towards the bottom of post.
http://forum.xda-developers.com/showthread.php?t=550131
Click to expand...
Click to collapse
Actually, near the bottom of post #2 of that thread, you will find the instructions to return to stock condition.
Basically flash stock ROM & radio > use relocker to relock SPL > good to go.
thanks guys appreciate your help
OK so i got the stock ROM, but I had some issues with the relocker...when i tried it on my PC the spyware flipped out on it and the .exe file didn't even work. How would i fix my phone on a MAC as thats what im using. Any Help?
Turn off anti-virus , download and install, turned on virus protection..
very very common issue.
well i only have mac now cause i went back to school. so how can i do it without an exe
bump any way this is possible on a mac? I really need help....
Also I was wondering is there anyway to block a number on your Tilt2...is there any application i can download to do this
ATT says its not possible
The flashing tools don't play well with Mac. Find a friend with an XP system. Vista and Windows7 "usually" work, but XP is the easiest.
For a call blocker, how about just using this websites search function to search "call blocker"? (yes, you will get some useful results).
tlglegacy said:
Also I was wondering is there anyway to block a number on your Tilt2...is there any application i can download to do this
ATT says its not possible
Click to expand...
Click to collapse
They are correct, it is not possible. Also, better thread title next time.

Categories

Resources