Help with qtek 9100 rom upgrade crash - Upgrading, Modifying and Unlocking

Hello, while I was upgrading my qtek to wm6 there was a power failure, now I`m stuck at the first splash screen. The info I can read is:
IPL 2.21.001
SPL 2.21.olip
GSM 02.47.11
OS 11.11.11.11
The phone was working fine, I regret doing this upgrade, now I have a beautiful brick.
On the other hand, I can get it to start in bootloader mode with the red, green and blue screen, I can get it to show USB connection at the bottom left corner of the screen, I CANT get it to connect with active sync.
I am new at this, as a matter of fact this is my first time writing in this forum, could somebody walk me to the process of reviving my phone?
Thank you all vey much.

Related

Need bootloader for Qtek 9000

Forgive me for my inherent stupidity. My Qtek 9000 device fails to boot up and stays stuck at the splash screen. It shows me the Radio, CE image versions, but it does not boot. I even tried the upgrade procedures suggested to the Qtek ROM. My only guess at this time is I have corrupted my bootloader. Where can i get a bootloader .bin file so that I can use mtty and try putting my bootloader back on. Any help in this matter is highly appreciated. I just don;t want a $1000 Qtek paperweight on my hands.
Very Strange coincidence. My Qtek 9000 has the same problem
Just before reading your post I tried to hard reset my Qtek 9000 to reinstall my preferred software after some experimentation.
Now my device will not get beyond the 'spash screen'.
I have no idea what to do?
The device will power up and illuminate the screen with the Rom Details then after 15 seconds just powers off.
Somebody help please!!!

Help Please..................Jasjar crash

I was upgrading my radio last night and power went out in area. The device now freezes at blue imate logo page. Will not boot up. When I hard or soft reset it still stops at blue screen. Can not get into bootloader. XP says it does not recognize the device. ActiveSync does not connect.
Screen says "No GMS". D 1.30 .76 WWE. Just out of warranty. Any help would be appreciated.
cboy!!!
cboy77 said:
I was upgrading my radio last night and power went out in area. The device now freezes at blue imate logo page. Will not boot up. When I hard or soft reset it still stops at blue screen. Can not get into bootloader. XP says it does not recognize the device. ActiveSync does not connect.
Screen says "No GMS". D 1.30 .76 WWE. Just out of warranty. Any help would be appreciated.
cboy!!!
Click to expand...
Click to collapse
I have sent you a pm, that will correct your device. Please check your pm's...
Take care,
-Jwrightmcps
Jasjar Problems
Went in and restored the DOC to original layout. Have been trying to load Original OEM ROM (Jasjar WWE 1.30.76). Keep getting Country ID Error.
Any assistance would be appreciated.
Thanks in advance!!!!!!!!!!!!!!!
cboy77

MAJOR problem loading WM6

I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.
did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?
god, I'm gonna admit, I have no idea what any of that stuff is. I know the tricolor screen, I dont know what an SPL is.. a friend of mine usually sends me the upgrades for my programs and i just follow his instructions, but as i was loading the new version it got unplugged and when i tried to follow the restore options it wouldnt restore the upgrade.. so I've learned the term is bricking.
Activesync won't reconnect the phone.. it tries, then doesnt recognize the device.. so even if i try to downgrade to 1.04, it wont work because it wont sync with the damn computer.. I hard reset, i soft reset, i got it to the tricolor screen, i tried all the stuff in the hermes upgrade problems thread, but i dont know wtf i'm doing. the file mtty.exe wont work.. it just freezes at whatever screen i happen to get it to, be it the tricolor or the HTC screen.
please, someone help me out.. I apologize in advance for not being as savvy as everyone else, but I need some advice here.
Go the tri colour screen
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine
Did u hard SPL your device?
Costanza said:
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine
Click to expand...
Click to collapse
I hard reset, I soft reset, it freezes either way. The only way the computer recognizes the phone is when I get the tricolor screen but active sync wont connect to FINISH loading the upgrade.
antonlim1999 said:
Did u hard SPL your device?
Click to expand...
Click to collapse
I cant because it wont connect to activesync to install anything else.. i cant dongrade, upgrade, nothing! i cant get to version 1.04 from the 1.06 im running because activesync wont recognize my phone.
I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?
sg10 said:
I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?
Click to expand...
Click to collapse
I already had wm6, i was just getting a better version that didnt have as many bugs.. I began loading it, it got to 45%, then the cat knocked the cable out and it got messed up.. I dont believe it was hard-spl beforehand.. im gonna go with no.
Could you try to SPL in the tri colour mode (as you have contact between the unit and the PC)?
Link below has all (almost) info
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
A warning to those with an aversion to reading
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.
hiddenconcepts said:
I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.
Click to expand...
Click to collapse
You are not even in the right forum, you'll get better help elsewhere.
Start reading here: http://forum.xda-developers.com/showthread.php?t=286755
Hard SPL thread: http://forum.xda-developers.com/showthread.php?t=296722
philjohn said:
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.
Click to expand...
Click to collapse
thanks, but I've upgraded before to other versions without a problem and I know that pulling the plug out is a bad idea.. the cat jumped up and ripped it out causing it to brick.
What all the smart arses on this site should be telling you is that you don't need activesync to run the upgrade - it will work just fine from the tri-colour screen.
First off, when you get your phone into the tri-colour screen, check the SPL version - if it isn't 2.10 olipro, the first thing you need to do is read the vanx guide's (link in my sig) and get hard SPL 2.10 olipro on there ASAP - this will prevent you from bricking your phone.
If it is already 2.10 olipro, then breathe a sigh of relief as everthing is OK - just put it into the tri-colour screen and run the upgrade again - it should start again with out a problem.
Cheers,
Smiffy.

Imate Kjam Will not boot

Hi all i am new to all this i tried to load a newer rom on my Imate it had an error and froze did a reset and now it only comes to the 3 colour boot screen i have tried a hard reset but no luck and have downloaded the offical rom again i can get into the bootloader screen by pressing camera button and on and connect with the usb the thing is how do I load the rom the Program"RUU program" says u must have a active sync connection and it will not work in the bootloader it says usb in the left conner but active sync will not work is there any other program that doesnt use active sync to load the rom to my phone i have been reading the forum and seen similar problems all with the reply load wizardlove cant find the it all the links are broken or doesnt excest I need to get my phone running asap and if i send it in it will only be returned inn 6weeks they say I am from south africa and the guys here can be a lot of help coz the know nothing so if anybody can help me please it would be great thanks
Which is your device a G3 or G4 ? post the IPL/SPL...? of the phone to determine the version. As far as it gets to bootloaders (tricolor screen) you are safe,its just a bad flash,nothing to worry,you'll soon have it working fine.
Which rom were you trying to upgrade to ? and what exactly were you doing.First, is your phone SIM/CID unlocked,if you were trying to upgrade to a latest wm6 rom,its essential to have the phone CID unlocked
Secondly,while in bootloaders, Activesync doesn't work,you got to have a working OS on the phone to sync with activesync,but when in bootloaders and usb appears in the bottom of the screen,you can flash the rom.
Cheers!
K Jam hangs at blue screen
Hi to all,
I have a K jam more then 1 years old. Now It is giving some probem. There is no display but only light in the screen but I make call and recieve calls!.
First time when problem arised. I pressed 3 battons(2 left side and 1 up side)the screen will became perfect and when I remove the battery & reinserted, the problem arised again. When I asked some 2 to 3 mobile service mens, thay told that there is a problem with OS (By reinstalling the OS it will be repaired). I think probem is with the strip connect motherboard to the LCD, that could be cuted but service mens told no, it is problem with OS.
Where I can get the OS, WM5 is preinstalled in it.
Still it did not open the mobile. Please help me
Many Thanks for all
Srikanth.K
hellol i m facing the same problem when i start my imate k jam it does nt boot to windows n stopd on three color screen wht to do now help me plz to sort out
I feel your Pain! im in the same boat the three colour screen! all my Imate only gives
me IPL 2.16.0001 an SPL 2.16.0001 not even an OS
i downloaded wm6 from here and i followed some step of senior member of these site.now i have a problem.when i upgraded my mobile restart after booting and again restart so i am in serious problem.what can i do now.any help.
my imate k-jam ipl 1.01 and spl is 1.06
please help me

[Q] Rookie Mistake

Hi I have and IMATE PDA2k EVDO and I tried a d-two rom and I now have the device sitting on the 4 color screen every time I reset it. Any idea how I reset it back to defaults so I can load another image onto it, I have the original image. any advice would be appreciated.
Thanks,
Actually I just fixed it.
Anyone know of any WM5,6 or 6.5 roms that work on this phone. The EVDO network is dead here in Australia so I just want to convert it into a PDA.
For the love of God... if you are going to make a thread saying "Hey guys, I broke this, how do I fix it?" Do not EVER update with "I fixed it!" without telling us HOW you fixed it.
I thought it was such simple fix it did not requiere explaination. To enter the bootloader you do the following
Press Power + record (above the volume slider) + softreset at the same time.
This puts it into the load mode so you can reflash.
problem with my xda iis
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
about WM 6 rom, maybe you can look at ftp://ftp.xda-developers.com/BlueAngel/Shipped_Complete_Updates/
or at http://shipped-roms.com/index.php?category=windows mobile&model=Blue Angel
try to flashing rom again
You sir are an idiot.
A Blue Angel rom will not work for a Harrier.
So delete your comment because some other idiot will follow your bad instructions then **** up their phone and make another idiotic post.
Yea so did anyone figure out this whole problem with the white boot loader screen? I'm no where near a programmer or anything but I think my boot loader version is out dated. My HARRIER, not blue angel, is stuck at a white screen that reads Serial(USB when connected to usb of course) and v1.02. I've had a Harrier before this and it had the four color screen for boot loader. Am I on to something here?
Oh btw I already tried to reflash the rom over and over but updater keeps saying it can't connect.
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
I have the same problem, anyone found a fix?
yes I have too same problem..plz help
i have a problem
Obviously.
But which one?
Tell us as elaborate as possible.
Problems Blue Angel Harrier Alpine
B-44 said:
Obviously.
But which one?
Tell us as elaborate as possible.
Click to expand...
Click to collapse
Please be careful: This is a Blue Angel (BA) Thread!
As Hima and Alpine Fora are closed, i will try to help as well as possible,
but please post marked "off topic"- hope moderators won't intervene...
And always first work out which device you're talking about.
Still love Alpine...
@admin: I know it's quite impossible to keep all these legacy threads alive- but what about some rescue thread, e.g. for non-touch-screen-phones,the Hima-BA-Family?
As i know from Siemens/BenQ Phones, it has gone silent around here, but from time to time some collectors appear which shouildn't be left alone.

Categories

Resources