Hello all,
it seems some one has flashed my SPV M2000 with a o2 rom in an attempt to "unlock" it, however they have rendered the phone useless along with the wifi.
Where can i obtain the original M2000 rom from so i can reflash it back to original?
Doughnut said:
Hello all,
it seems some one has flashed my SPV M2000 with a o2 rom in an attempt to "unlock" it, however they have rendered the phone useless along with the wifi.
Where can i obtain the original M2000 rom from so i can reflash it back to original?
Click to expand...
Click to collapse
orange still have last firmware posted if not then lemme know as I tihnk I still have it. but I donZt trust it after their initial firmware had faulty bluetooth stack
you can download the orange spv m2000 rom from here
good luck
Tested and working, not a bad rom tbh fast and stable so far
Related
my brother has the one of these o2 exec , but he has somehow reflashed the rom and now is it just a blank screen- is there a way of getting the rom, etc from another o2 exec and reload it to his? I have never done this before and he has had enough of messing around with it and just bought a new m3100, so i was wonderig if I could repair this, if so I have just aquired a new phone for nothing .
Any help will be much apprieciated.
thanks
sam
If you look well the screen an see some word like usb up and v.1.0 down is possible to repair.
Try to reflash the ROM via Bootloader mode.
I used the method of SD back-up to back-up the ROM of my Orange SPV M1500 on the SD card. ( http://en.pdamobiz.com/en/forum/PDAforum_posts.asp?TID=151&PN=1). Then I flashed the phone with O2 upgraded ROM. It worked although there are some tricks. However, after that, I wanted to flash the original Orange ROM back. But I failed everytime. The new O2 ROM seems stay there forever.
I don't know how I can redo it. I have searched for the Orange ROM but no happy. Maybe some experts can do it? Please leave your message. Thanks!
Hi everyone,
A while ago I was stupid and tried to flash my O2 XDA Orbit without fully reading the instructions and therefore ended up "bricking" the device. It turns on but seems to hang on the "O2 Welcome Screen" which shows the following information:
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
The device can boot up into the bootloader screen no problems and I have tried to install various ROM's from the German O2 WM6 ROM to the UK T-Mobile WM5 ROM but with no success, it just gets to 3% then reboots.
Does anyone know a way that I can restore the original O2 UK WM5 ROM from the bootloader? Or at least get it working again?
At this point there is no O2 Rom avaliable, you will have to wait till they finally release the WM6 Rom sometime this Summer.
Lordao
try this
http://forum.xda-developers.com/showthread.php?t=312495
go to this tread and test it
1234567890
No Joy
pvdhelm said:
http://forum.xda-developers.com/showthread.php?t=312495
go to this tread and test it
Click to expand...
Click to collapse
Thank you however I have tried the above instructions but my device just gets to 3% then reboots.
Does anyone know what the MTTY.EXE software is all about and is there any way that I can manually force the device to Flash using this?
Or!!!!!
Is there a way for me to clone a mates xda orbit and drop the image onto mine? Both were purchased at the same time just I thought i'd be clever and update mine which didn't quite work out.
Have you already tried to flash a rom by using your microSD card ?
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
try to flash it from sd card if your orbit is cid unlocked
not sure
I dont think my device is cid unlocked as it would have worked with the updated rom install, wouldn't it? sorry pretty new to all this.
I have tried to flash straight from the sd card but it just searches through the sd card then goes straight to the multicoloured bootloader screen.
Anyother ways or is there a better rom that i could use?
hi all i have a orange uni i have unlocked the sim so i can run my o2 sim
i have 2 problems
1 i have tried the wonderfull uni unlock from buzz my system says its unlocked but no matter how i try it will not show up in file explorrer or any other software could the problem be the chip set on my phone mine is m-systems.
2 i have also tried to install the o2 stock rom it seemsto install ok but when i cold boot it sticks on the boot screen but the picture is all stripy (so you can not see the picture at all)
i have the uni working with the orange rom minus orange software but i would like to get it sorted to run o2 roms.
thanks for any advice
nocatmcm
I have Orange branded spv m700 and have unlocked and supercid'd the device using pof's tool. I then added HardSpl (Olipro 1.20). All appear to have loaded fine - phone is unlocked and Olipro shows up when put into bootloader.
So, the problem - every time I flash a cooked ROM (Ausdim, NiAx, FiNixNover...?) it won't boot past the first screen. I can rescue the situation by putting device into bootloader and flashing the official WM6 ROM (no radio, no ipl....) and it boots up just fine.
Can anybody help or at least point me in the direction of some good advice?
hmm... odd... can you list step by step what your procedure is for flashing the ROMs
I've done lots of devices - old XDA2i, SPVM600, wifes SPV M700 (unlocked, hard spl etc and flashed away!
This particular device shows IPL 0.50 & SPL 1.20 Olipro. It is unlocked (have o2 sim working in it), and should be SuperCid (I checked the box and radio shows as 1.16.00.00 - pof's patch I believe?). I also re-run HardSpl and Pof's unlock/supercid patch just in case it hadn't flashed properly.
I generally just download ROM and flash via RUU. Occasionally I get the device not responding error so I just re-run RUU from the bootloader screen.
Have tried WM 6.1 and 6.0 cooked roms but all show initial boot screen (numbers along bottom) next screen and then frozen, have waited and waited and nothing. Also, it would not flash back to Mozzers WM5 Orange UK ROM - same symptoms. I thought it was bricked, but the Dopod WM6 flashed perfectly.
Hope that helps - thanks for looking into my problem.
anybody please? por favor........
hmm.. i remember someone having a similar problem but it was some time ago..
two things to try just in case...
1) i'd manually go to bootloader (hard-spl) before flashing
2) Have you tried to flash from SD card? this method seems to provide less problems..
let me know how it goes..
A degree of success - managed to flash WM6 AX3L. All seems to be working. As I recall this is very similar to the official ROM and I used to use it last year because it is very stable. Think I moved on because of the missing email accounts problem. Will happily keep it if I can sort the email problem out. Never really had much fun with the hard reset after loading method - is there another/better way? Just wondering.
Also, now I have a "cooked" rom loaded perhaps it will stop being so sensitive.....!!
How strange! Have just flashed Akeo's new Diamond port ROM and no problems. Not only that, the ROM is FAB!!!